Monoclonal antibody produced by heterologous indirect enzyme-linked immunosorbent assay and its application for parathion residue determination in agricultural and environmental samples

A heterologous indirect enzyme-linked immunosorbent assay (ELISA) was developed, which was based on monoclonal antibody (Mab) to determine parathion residue in agricultural and environmental samples. Eight Mabs were produced by introducing the heterologous indirect ELISA into the screening procedure. It was shown that these Mabs had more broad-reactivity with twenty competitors than that of 5H7 (Mab produced by homologous screening). So it became much easier using these new Mabs to develop heterologous immunoassays. In addition, all the developed heterologous ELISAs could be used to determine parathion residue in semiquantitative or quantitative level, and their detection limitation (LOD) was around 2 ng/mL. Compared with the previous heterologous ELISA (hapten 11/5H7) with IC₅₀ of 13.3 ng/mL, a better heterologous ELISA (hapten 11/1E1) was obtained with IC₅₀ of 3.8 ng/mL, which improved the sensitivity 3.5 times. Finally, the latter was applied to parathion residue determination in spiked agricultural and environmental samples without extraction or cleanup. The average recoveries of parathion added to water, soil, cucumber, Chinese cabbage and carrot were between 80.4 % and 111.8 %. The LOD for water and soil samples was 5 ng/mL, and the LOD for cucumber, rice and corn samples was 10 ng/mL.     

Determination of PAHs in wastewater irrigated agricultural soil using accelerated solvent extraction

A procedure was developed for determination of 16 polycyclic aromatic hydrocarbons (PAHs) in heavily contaminated paddy soil from wastewater irrigated farmland near Tianjin. The sample was distilled with accelerated solvent extraction (ASE), purified by a silica gel column, and measured with GC/MS. The optimal conditions for the distillation were at 140 degrees C (1500 psi) with a 1:1 mixture of dichloromethane and acetone for 5 min. Application of cyclohexane for extract transfer improved the recovery when the ASE extraction was followed by a silica gel cleanup procedure. Recoveries from the method for 16 PAHs ranged from 57-140% with the coefficients of variation of the results ranging from 0.35% to 5.75%. The total 16 PAHs in a composite sample collected from a wastewater irrigated paddy field near Tianjin was 3.90 mg/kg.     

Comparison of gas chromatography and immunoassay methods for analysis of total DDT in calcareous soils

Three different calcareous soil samples from Lebanon were analyzed for total DDT pesticide residue using GC and ELISA methods. Two experiments were conducted on three different calcareous soil samples. In each experiment, triplicates of 5 gm soil samples were each fortified with standard solutions of DDE to reach concentrations of 0, 5, 25, 50, 100 and 200 ng g(-1) and allowed to equilibrate at room temperature for 6 hours. Each sample was then extracted with 25 mL of 90% methanol by shaking in glass bottles on a mechanical shaker for 16 hours. The bottles were allowed to stand for 30 minutes and aliquots were taken from the clear supernatant for analyses without further cleanup. The total DDT in the extract was measured in triplicate by GC and ELISA. The results indicated that the two methods were highly correlated (R = 0.955-0.994). Differences in soil properties did not affect the accuracy of the detection limits of ELISA. Immunoassay technique can be used for rapid and accurate measurement of total DDT residues in mineral calcareous soils in Lebanon.     

An enzyme-linked immunosorbent assay for the determination of dioxins in contaminated sediment and soil samples

A 96-microwell enzyme-linked immunosorbent assay (ELISA) method was evaluated to determine PCDDs/PCDFs in sediment and soil samples from an EPA Superfund site. Samples were prepared and analyzed by both the ELISA and a gas chromatography/high resolution mass spectrometry (GC/HRMS) method. Comparable method precision, accuracy, and detection level (8 ng kg(-1)) were achieved by the ELISA method with respect to GC/HRMS. However, the extraction and cleanup method developed for the ELISA requires refinement for the soil type that yielded a waxy residue after sample processing. Four types of statistical analyses (Pearson correlation coefficient, paired t-test, nonparametric tests, and McNemar's test of association) were performed to determine whether the two methods produced statistically different results. The log-transformed ELISA-derived 2,3,7,8-tetrachlorodibenzo-p-dioxin values and log-transformed GC/HRMS-derived TEQ values were significantly correlated (r=0.79) at the 0.05 level. The median difference in values between ELISA and GC/HRMS was not significant at the 0.05 level. Low false negative and false positive rates (<10%) were observed for the ELISA when compared to the GC/HRMS at 1,000 ng TEQ kg(-1). The findings suggest that immunochemical technology could be a complementary monitoring tool for determining concentrations at the 1,000 ng TEQ kg(-1) action level for contaminated sediment and soil. The ELISA could also be used in an analytical triage approach to screen and rank samples prior to instrumental analysis.     

Selenium extractability from a contaminated fine soil fraction: implication on soil cleanup

Two batches of fine soil fraction of an acidic soil were deliberately contaminated with selenite (Se(IV)) and selenate (Se(VI)), respectively, and aged for more than 220 days. Speciation analysis using continuous flow-through hydride generation atomic absorption spectrometry (HGAAS) indicated that the species were predominant in their respective aged soils. A selective sequential extraction scheme was employed to fractionate the Se retained in the soils into six fractions of varying retentions. Abilities of various chemical reagents in extracting the Se in the two soil batches were then evaluated. The reagents investigated were sodium salts such as sodium chloride (NaCl), sodium sulfate (Na2SO4), sodium carbonate (Na2CO3), and sodium phosphate (Na3PO4), and two oxidants, namely, hydrogen peroxide (H2O2) and potassium permanganate (KMnO4). It was found that NaCl, Na2SO4, and Na2CO3 could only extract the exchangeable fraction of Se, while Na3PO4 could extract the exchangeable and strongly-bound fractions. Selenate was extracted more than Se(IV) by the salts. The kinetics of Se(IV) extraction by Na3PO4 could be best described by the Elovich model, while the Ritchie second-order model was the most appropriate to describe Se(VI) extraction. Efficiencies of the oxidants in Se(IV) extraction highly depended on their applied dosages. Both H2O2 and KMnO4 were able to extract greater than 93% of total Se, and therefore were significantly more effective than the salts in Se(IV) extraction.     

Sorption and desorption kinetics of diuron,fluometuron, prometryn and pyrithiobac sodium in soils

Abstract

The sorption and desorption characteristics of four herbicides (diuron, fluometuron, prometryn and pyrithiobac‐sodium) in three different cotton growing soils of Australia was investigated. Kinetics and equilibrium sorption and desorption isotherms were determined using the batch equilibrium technique. Sorption was rapid (> 80% in 2 h) and sorption equilibrium was achieved within a short period of time (ca 4 h) for all herbicides. Sorption isotherms of the four herbicides were described by Freundlich equation with an r² value > 0.98. The herbicide sorption as measured by the distribution coefficient (K_d) values ranged from 3.24 to 5.71 L/kg for diuron, 0.44 to 1.13 L/kg for fluometuron, 1.78 to 6.04 L/kg for prometryn and 0.22 to 0.59 L/kg for pyrithiobac‐sodium. Sorption of herbicides was higher in the Moree soil than in Narrabri and Wee Waa soils. When the K_d values were normalised to organic carbon content of the soils (K_oC), it suggested that the affinity of the herbicides to the organic carbon increased in the order: pyrithiobac‐sodium < fluometuron < prometryn < diuron. The desorption isotherms were also adequately described by the Freundlich equation. For desorption, all herbicides exhibited hysteresis and the hysteresis was stronger for highly sorbed herbicides (diuron and prometryn) than the weakly sorbed herbicides (fluometuron and pyrithiobac‐sodium). Hysteresis was also quantified as the percentage of sorbed herbicides which is not released during the desorption step ω = [n_ad / n_de ‐1] x 100). Soil type and initial concentration had significant effect on ω. The effect of sorption and desorption properties of these four herbicides on the off‐site transport to contaminate surface and groundwater are also discussed in this paper.     

Analysis of PCDD/Fs and dioxin-like PCBs in atmospheric deposition samples from the Flemish measurement network: Optimization and validation of a new CALUX bioassay method

Since the CALUX (Chemically Activated LUciferase gene eXpression) bioassay is a fast, sensitive and inexpensive tool for the analysis of a high number of samples, validation of new methods is urgently needed. In this study, a new method for the analysis of PCDD/Fs and dioxin-like PCBs in atmospheric deposition samples with the CALUX bioassay was developed, optimized and validated. The method consists of 4 steps: filtration, extraction, clean up and bioassay analysis. To avoid the use of large amounts of toxic solvents, new techniques were used for filtration and extraction: a C18 filter was used instead of a liquid/liquid extraction and an Accelerated Solvent Extractor (ASE) was used instead of the traditional soxhlet extraction. After pre-oxidation of the sample extract, clean up was done using a multi-layer silica gel column coupled to a carbon column. The PCDD/F and PCB fractions were finally analyzed with the H1L7.5c1 and/or the H1L6.1c3 mouse hepatoma cell lines. The limit of quantification was 1.4 pg CALUX-BEQ m⁻² d⁻¹ for the PCBs and 5.6 pg CALUX-BEQ m⁻² d⁻¹ for the PCDD/Fs, when using the new sensitive H1L7.5c1 cell line. The GC-HRMS recovery for all PCDD/F congeners was between 55% and 112%, with a mean recovery of 90%. CALUX recoveries of spiked procedural blanks were between the accepted ranges of 80-120%. Repeatability and reproducibility were satisfactory and no interferences from metals were detected. The first results from the Flemish measurement program showed good correlation between CALUX and GC-HRMS.     

Development of indirect competitive ELISA using egg yolk-derived immunoglobulin (IgY) for the detection of Gentamicin residues

Gentamicin (Gent) is an aminoglycoside antibiotic being used in livestock sector. Gent residues could cause some genetic disorders by nonsense mutations. This study aimed to develop IgY-based ELISA for the detection of Gent in animal products. Gent was conjugated with Bovine serum albumin (BSA) by carbodiimide method for further immunization in the laying chickens. PEG-6000 extraction method was employed to extract IgY from the egg yolk. The titer of anti-Gent-IgY attained the peak of 1:256,000 after the 5^th booster immunization. Checkerboard titration confirmed that, anti-Gent IgY in 1:2,000 dilution could give an Optical Density (OD) 1.0 at 2 µg mL^?1 of Gent-OVA coating concentration. IgY-based indirect competitive ELISA (Ic-ELISA) showed that, the IC₅₀ value of anti-Gent IgY was 2.69 ng mL^?1 and regression curve equation was y = ?16.27x + 56.97 (R² = 0.95, n = 3), confirming that, the detection limit (LOD, IC₁₀ value) was 0.01 ng mL^?1. Recoveries from fresh milk, pork and chicken samples were ranged from 69.82% to 94.32%, with relative standard deviation lower than 10.88%. Our results suggested that generated anti-Gent IgY antibodies can be used in routine screening analysis of Gent residues in food samples.     

Optimisation of pressurised liquid extraction for elimination of sulphur interferences during determination of organotin compounds in sulphur-rich sediments by gas chromatography with flame photometric detection

A simple method for species-selective analysis of organotin compounds (OTCs) (butyl and phenyl) in sediments was developed. The sample preparation procedure was specifically optimised for sulphur-rich sediments to eliminate interferences from elemental sulphur and organosulphur compounds. Tin species were extracted from sediment samples using pressurised liquid extraction technique (PLE), ethylated - with simultaneous extraction to isooctane - in aqueous phase with sodium tetraethylborate (NaBEt(4)) and separated/detected by gas chromatography with flame photometric detection (GC-FPD). PLE operational variables (extraction temperature and pressure, solvent composition and number of static extraction steps) and extract handling routine were fine-tuned to minimise the amount of extracted interferents while keeping OTCs recovery at an acceptable level. Best results were obtained after extraction of sediment samples with methanol/water (75% v/v methanol) solution of acetic acid/sodium acetate with tropolone addition (0.6 g l(-1)). Derivatisation of low temperature, high-pressure (50 degrees C, 13.8 MPa) extracts gives isooctane extracts which are clean enough to be directly analysed by GC-FPD without any further cleanup. Interferences from elemental sulphur were completely eliminated while concentrations of other interferents were reduced to the level not impairing quantitation of OTCs under the study. No negative effects in terms of chromatographic column deterioration were observed after repeated injections of such extracts. Two certified reference materials, BCR646 and PACS-2, were analysed to assess performance of the method. Recoveries of all OTCs under the study, except MBT, were in the range of 91-114%. MBT extraction efficiency was low (34-47%) therefore the method is unsuitable for precise determinations of this compound.     

Heterogeneity of nodularin bioaccumulation in northern Baltic Sea flounders in 2002

The cyanobacterial hepatotoxin nodularin is abundantly produced by the cyanobacterium Nodularia spumigena in the Baltic Sea during July-August. Nodularin is a potent hepatotoxin and a tumour promoter, distributed in various Baltic Sea environmental compartments, especially food webs involving mussels. Flounders receive nodularin through consumption of blue mussels. In this study nodularin concentrations in individual flounders (liver) were examined between July and September 2002 (six sample sets, four to 10 samples/set), providing information about contribution of sampling on estimates of bioaccumulation intensity. Toxin was determined using liquid chromatography/mass spectrometry (LC/MS) and enzyme-linked immunosorbent assay (ELISA). Additionally, liver histopathology was examined. Observed toxin concentrations were ND-390 microg kg(-1) dw (LC/MS) and 20-2230 microg kg(-1) dw (ELISA), with maximum concentrations in September (ELISA). The ELISA protocol generally resulted in higher, up to approximately 10-fold, toxin concentrations than LC/MS, with increasing difference toward September. This difference may have originated from different extraction solvents in LC/MS and ELISA, ion suppression in LC/MS, and temporal increase in nodularin metabolites detectable with ELISA. The differences in toxin concentrations between individual liver samples were considerable with relative standard deviation values of 20-154% (LC/MS) and 28-106% (ELISA). Since the precision of the ELISA method employed was <25% and that of LC/MS <10%, it can be concluded that the largest source of error in bioaccumulation estimates may be an inadequate number of samples. Although there were tissue lesions in several liver samples, occurrence of lesions was not related to toxin concentrations.     

Effect of condensed organic matter on solvent extraction and aqueous leaching of polycyclic aromatic hydrocarbons in soils and sediments

The contents of nonhydrolyzable organic matter (NHC) and black carbon (BC) were measured in soils and sediments from the Pearl River Delta, South China. Polycyclic aromatic hydrocarbons (PAHs) were extracted respectively by Soxhlet and an accelerated solvent extraction device (ASE) using different solvents. In addition, sequential aqueous leaching at different temperatures was carried out. The PAH content extracted with the sequential three solvent ASE is two times higher than that using the Soxhlet extraction method. The relationship of the PAH content with the NHC content is very significant. The PAH concentrations measured at various temperature steps fit well to the Van't Hoff equation and the enthalpy was estimated. The investigation indicates that condensed organic matter such as kerogen carbon, aged organic matter, and BC is relevant for the extraction and distribution of native PAHs in the investigated field soils and sediments.     

Optimization and validation of enzyme-linked immunosorbent assay for the determination of endosulfan residues in food samples

In this study, an enzyme-linked immunosorbent assay (ELISA) was optimized and applied to the determination of endosulfan residues in 20 different kinds of food commodities including vegetables, dry fruits, tea and meat. The limit of detection (IC(15)) was 0.8 microg kg(-1) and the sensitivity (IC(50)) was 5.3 microg kg(-1). Three simple extraction methods were developed, including shaking on the rotary shaker at 250 r min(-1) overnight, shaking on the rotary shaker for 1 h and thoroughly mixing for 2 min. Methanol was used as the extraction solvent in this study. The extracts were diluted in 0.5% fish skin gelatin (FG) in phosphate-buffered saline (PBS) at various dilutions in order to remove the matrix interference. For cabbage (purple and green), asparagus, Japanese green, Chinese cabbage, scallion, garland chrysanthemum, spinach and garlic, the extracts were diluted 10-fold; for carrots and tea, the extracts were diluted 15-fold and 900-fold, respectively. The extracts of celery, adzuki beans and chestnuts, were diluted 20-fold to avoid the matrix interference; ginger, vegetable soybean and peanut extracts were diluted 100-fold; mutton and chicken extracts were diluted 10-fold and for eel, the dilution was 40-fold. Average recoveries were 63.13-125.61%. Validation was conducted by gas chromatography (GC) and gas chromatography-mass spectrometry (GC-MS). The results of this study will be useful to the wide application of an ELISA for the rapid determination of pesticides in food samples.     

Comparisons of metal leachability for various wastes by extraction and leaching methods

The objective of this research was to evaluate three extraction tests, i.e., toxicity characteristic leaching procedures (TCLP), extraction procedure (EP), and American Society for Testing and Materials (ASTM) methods, for their ability to extract metals in chemical sludge and incineration bottom ash, in terms of the precision of analytical results. Typical chemical sludges, including the electroplating and dye-stuff sludges, the municipal solid waste incineration bottom ash, the leather debris, and the steel-mill bottom residue containing Cd, Cr, Cu, Pb, and Zn were prepared for the lysimetry test (dynamic testing) to compare with the extraction results. Results show that for bottom residue and dye-stuff sludge, the concentration of metal leached was almost the same between the lysimetry leaching and the TCLP tests. The metal concentration followed the order: TCLP approximately = EP > ASTM. TCLP and EP exhibited almost the same relative standard deviation (RSD) value. Therefore, the results of the TCLP tests for bottom residue and dye-stuff sludge, which have a low metal content and alkalinity, can be used to estimate the metal concentration leached by typical acid rain in Taiwan; whereas the ASTM extraction test may be a better indicator of the lysimetry test.     

LC-MS/MS determination of pesticide residues in fruits and vegetables

The aim of the research is to evaluate pesticide residue contamination of fresh and frozen fruits and vegetables, agricultural raw material, purchased from Polish farmers for production of frozen fruits and vegetables, and the estimation of the multiresidue method effectiveness expressed as the proportion of pesticides detected in food samples to the total number of pesticides analyzed by multiresidue methods. A total of 144 samples (of black currants, red currants, raspberries, cherries, strawberries, blackberries, cauliflowers and broccoli) were analyzed using LC-MS/MS method for the determination of 60 pesticides. QuEChERS extraction, matrix-matched calibration and dynamic multiple reaction monitoring method were used. Residues of 15 compounds, mainly fungicides and insecticides, were detected in 46 samples. The percentage of samples with residues above the maximum residue levels (MRL) was 15%, whereas samples with residues below MRL were 17%. A total of 13 samples contained more than one pesticide residue. Pesticide residues were detected most often in samples of black currants (50%), broccoli (36.4%), raspberries (29%) and red currants (21.8%). The most frequently detected pesticides were carbendazim and acetamiprid. The proportion of pesticides detected during our study to the total number of analyzed pesticides amounted to 25%. It was compared to literature findings. For three fourth of multiresidue methods, the proportion was below 50% for methods developed for the analysis of less than 100 pesticides, and below 30% for methods developed for the analysis of more than 100 pesticides. It appears that a lot of efforts and means is lost on pesticides never or rarely detected in examined samples. The workload and cost effectiveness of the development and application of multiresidue methods along with the range of pesticides covered by the method should be carefully and thoroughly considered anytime when a new method or workflow is developed. Including non-targeted screenings in pesticide residue control seems to be an alternative worth considering.     

Determination of levoglucosan in atmospheric fine particulate matter

A microanalytical method suitable for the quantitative determination of the sugar anhydride levoglucosan in low-volume samples of atmospheric fine particulate matter (PM) has been developed and validated. The method incorporates two sugar anhydrides as quality control standards. The recovery standard sedoheptulosan (2,7-anhydro-beta-D-altro-heptulopyranose) in 20 microL solvent is added onto samples of the atmospheric fine PM and aged for 1 hr before ultrasonic extraction with ethylacetate/ triethylamine. The extract is reduced in volume, an internal standard is added (1,5-anhydro-D-mannitol), and a portion of the extract is derivatized with 10% by volume N-trimethylsilylimidazole. The derivatized extract is analyzed by gas chromatography/mass spectrometry (GC/MS). The recovery of levoglucosan using this procedure was 69 +/- 6% from five filters amended with 2 microg levoglucosan, and the reproducibility of the assay is 9%. The limit of detection is approximately 0.1 microg/mL, which is equivalent to approximately 3.5 ng/m3 for a 10 L/min sampler or approximately 8.7 ng/m3 for a 4 L/min personal sampler (assuming 24-hr integrated samples). We demonstrated that levoglucosan concentrations in collocated samples (expressed as ng/m3) were identical irrespective of whether samples were collected by PM with aerodynamic diameter < or = 2.5 microm or PM with aerodynamic diameter < or = 10 microm impactors. It was also demonstrated that X-ray fluorescence analysis of samples of atmospheric PM, before levoglucosan determinations, did not alter the levels of levoglucosan.     

Phosphorus release from ash, dried sludge and sludge residue from supercritical water oxidation by acid or base

Leaching of ash and dried sewage sludge were investigated and compared with the leaching results of sludge residue from supercritical water oxidation (SCWO). This article focuses on how the composition of ash and sludge residues influences the extraction of phosphate and heavy metals and if different treatment temperatures of the sludge effect the leachability. Results showed that acid leaching gave a higher release of phosphate than alkaline leaching for all ash and sludge residue samples. Also, alkaline leaching dissolved phosphate with a lower metal contamination than acid leaching. Furthermore, it was found that iron had a low release at both alkaline and acid leaching from ash and from SCWO residue. The difference in composition of ash and sludge residue samples had no significant influence on release of phosphate at high concentrations of acid. Phosphate release from ash, dried sludge at 300 degrees C and SCWO residue showed similar results at 1M acid leaching. However, it seems to be easier to release phosphate from the SCWO residue than from the ash at low acid concentrations. SCWO residue showed higher release than the other ashes at 0.5M HCl. Results for alkaline leaching showed higher release from ash at 1M NaOH than from SCWO residue or from dried sludge at 300 degrees C. The leaching of phosphate from dried sludge seems to be temperature dependent, as the dried sludge treated at higher temperature showed less release of phosphate. It was found that the pre-treatment of the ash may be important for better release of phosphate.     

Development of an efficient extraction method for oxytetracycline in animal manure for high performance liquid chromatography analysis

Oxytetracycline (2-(amino-hydroxy-methylidene)-4-dimethylamino-5,6,10,11,12a-pentahydroxy-6-methyl-4,4a,5,5a-tetrahydrotetracene-1,3,12-trione) is a major member of the tetracycline antibiotics family of which are widely administered to animals in concentrated animal feeding operations for purposes of therapeutical treatment and health protection. With the disposal of animal manure as fertilizer into agricultural land, tetracyclines enter the environment. However, tetracyclines chelate with multivalent cations and proteins, resulting in low extraction efficiencies from animal manure for tetracycline residue analysis. In this study an efficient extraction method for oxytetracycline from steer manure using methanol/water solution amended with chelating organic acid was developed for the analysis of high performance liquid chromatography. The effect of species and amount of amendment acids, shaking time, methanol/water ratio, manure weight, and repeated times of extraction was investigated. It was optimized to amend 2.5 g citric acid and 1.1 g oxalic acid with 10.0 g manure sample in a 50-ml centrifuge tube and extract with 15 ml methanol/water (9:1 in volume) by vigorously shaking for 30 min in a reciprocating shaker. After centrifugation at 11,000 rpm, supernatant is collected. Sample was extracted for a total of 3 times. The developed extraction method was further applied to extract oxytetracycline from fresh and aged cow manure, swine and poultry manure, and soil. Satisfactory recoveries ranging from (84.1 ± 2.4) % to (102.0 ± 3.1) % were obtained, demonstrating that the optimized extraction method is robust for oxytetracycline from different manure sample matrixes.     

Direct determination of neonicotinoid insecticides in an analytically challenging crop such as Chinese chives using selective ELISAs

ABSTRACT

Easy-to-use commercial kit-based enzyme-linked immunosorbent assays (ELISAs) have been used to detect neonicotinoid dinotefuran, clothianidin and imidacloprid in Chinese chives, which are considered a troublesome matrix for chromatographic techniques. Based on their high water solubility, water was used as an extractant. Matrix interference could be avoided substantially just diluting sample extracts. Average recoveries of insecticides from spiked samples were 85–113%, with relative standard deviation of <15%. The concentrations of insecticides detected from the spiked samples with the proposed ELISA methods correlated well with those by the reference high-performance liquid chromatography (HPLC) method. The residues analyzed by the ELISA methods were consistently 1.24 times that found by the HPLC method, attributable to loss of analyte during sample clean-up for HPLC analyses. It was revealed that the ELISA methods can be applied easily to pesticide residue analysis in troublesome matrix such as Chinese chives.     

Estrogenicity profile and estrogenic compounds determined in river sediments by chemical analysis, ELISA and yeast assays

An effects-directed strategy was applied to bed sediments of a polluted tributary in order to isolate and identify the major estrogenic chemicals it discharges into the River Po, the principal Italian watercourse. Sediment extract was concentrated by solid phase extraction and then fractioned into 10 fractions by reversed phase high performance liquid chromatography (RP-HPLC). Estrogenic activity of whole extract and fractions were determined using a recombinant yeast assay containing the human estrogen receptor (YES). The 10 fractions and whole extract were analysed for target compounds, e.g. estrone (E1), 17beta-estradiol (E2), estriol (E3), 4-nonylphenol (NP), 4-tert-octylphenol (t-OP), bisphenol A (BPA), using both liquid chromatography-tandem mass spectrometry (LC-MS/MS) and non-competitive enzyme-linked immunosorbent assays (ELISA). The YES assay determined high estrogenic activity in whole sediment (15.6 ng/g EE2 equivalents), and positive results for fractions nr 1, 2, 6, 7 and 8. E1, E3 and NP were the main estrogenic chemicals, however, other unidentified compounds contributed to sediment estrogenicity, particularly for polar fractions nr 1 and 2. A GC-MS screening performed in scan mode identified other potential contributors such as phthalates (DBP, BBP), and OP isomers. A next sampling campaign extended to other tributaries and receiving stretches of the River Po confirmed E1, E3 and NP as major estrogenic chemicals potentially threatening other sites of the main river. In general, target compound ELISAs have been shown to be suitable tools for a rapid screening of wide areas or large numbers of environmental samples for estrogenic risk. The potential for interferences suggests however to use cautiously the concentration values obtained from some of the immunoassays.     

Determination of benzene, toluene, ethylbenzene, xylenes in water at sub-ng l-1 levels by solid-phase microextraction coupled to cryo-trap gas chromatography-mass spectrometry

A trace analytical method of benzene, toluene, ethylbenzene and xylenes (BTEX) in water has been developed by using headspace solid-phase microextraction (HS-SPME) coupled to cryo-trap gas chromatography-mass spectrometry (GC-MS). The chromatographic peak shape for BTEX was improved by using cryo-trap equipment. The HS-SPME experimental procedures to extract BTEX from water were optimized with a 75 microm carboxen/polydimethylsiloxane (CAR/PDMS)-coated fiber at a sodium chloride concentration of 267 g l(-1), extraction for 15 min at 25 degrees C and desorption at 290 degrees C for 2 min. Good linearity was verified in a range of 0.0001-50 microg l(-1) for each analyte (r(2)=0.996-0.999). The limits of detection (LODs) of BTEX in water reached at sub-ng l(-1) levels. LODs of benzene, toluene, ethylbenzene, m/p-xylene and o-xylene were 0.04, 0.02, 0.05, 0.01 and 0.02 ng l(-1), respectively. The proposed analytical method was successfully used for the quantification of trace BTEX in ground water. The results indicate that HS-SPME coupled to cryo-trap GC-MS is an effective tool for analysis of BTEX in water samples at the sub-ng l(-1) level.