Pd/Ce0.5Zr0.5O2三效催化剂负载方法

分别采用沉积沉淀、直接混合和传统的浸渍法制备1% Pd/Ce_0.5Zr_0.5O₂ 催化剂, 研究了Pd负载方法对催化剂活性影响.运用H₂-TPR和原位漫反射红外(DRIFTS)研究了Pd-铈锆载体间的相互作用及Pd/Ce_0.5Zr_0.5O₂催化剂上的三效反应机理.结果表明沉积沉淀法制备的Pd/Ce_0.5Zr_0.5O₂催化剂(Pd-DP)表现出最强的Pd-载体作用及最优活性,原位红外实验发现Pd-DP上存在与传统的浸渍法制备的Pd-IMP催化剂不同的NO催化还原途径,推测Pd-载体间相互作用引起NO还原机理差异,进而导致活性差异.     

Removal of formaldehyde over MnxCe1-xO2 catalysts: Thermal catalytic oxidation versus ozone catalytic oxidation

MnxCe1- xO2（x： 0.3–0.9） prepared by Pechini method was used as a catalyst for the thermal catalytic oxidation of formaldehyde（HCHO）. At x = 0.3 and 0.5, most of the manganese was incorporated in the fluorite structure of Ce O2 to form a solid solution. The catalytic activity was best at x = 0.5, at which the temperature of 100% removal rate is the lowest（270°C）. The temperature for 100% removal of HCHO oxidation is reduced by approximately 40°C by loading 5 wt.% Cu Oxinto Mn0.5Ce0.5O2. With ozone catalytic oxidation, HCHO（61 ppm） in gas stream was completely oxidized by adding 506 ppm O3 over Mn0.5Ce0.5O2 catalyst with a GHSV（gas hourly space velocity） of 10,000 hr-1at 25°C. The effect of the molar ratio of O3 to HCHO was also investigated. As O3/HCHO ratio was increased from 3 to 8, the removal efficiency of HCHO was increased from 83.3% to 100%. With O3/HCHO ratio of 8, the mineralization efficiency of HCHO to CO2 was 86.1%. At 25°C, the p-type oxide semiconductor（Mn0.5Ce0.5O2） exhibited an excellent ozone decomposition efficiency of 99.2%,which significantly exceeded that of n-type oxide semiconductors such as Ti O2, which had a low ozone decomposition efficiency（9.81%）. At a GHSV of 10,000 hr-1, [O3]/[HCHO] = 3 and temperature of 25°C, a high HCHO removal efficiency（≥ 81.2%） was maintained throughout the durability test of 80 hr, indicating the long-term stability of the catalyst for HCHO removal.     

Reduction of NO by CO using Pd-CeTb and Pd-CeZr catalysts supported on SiO2 and La2O3-Al2O3

The catalytic activity of Pd catalysts supported on Ce_0.73Tb_0.27O_x/SiO₂, Ce_0.6Zr_0.4O_x/SiO₂, Ce_0.73Tb_0.27O_x/La₂O₃-Al₂O₃ and Ce_0.6Zr_0.4O_x/La₂O₃-Al₂O₃ was studied using the reduction of NO by CO. The catalysts were characterized by X-ray fluorescence, surface area, X-ray diffraction, temperature-programmed reduction, CO chemisorption and oxygen storage capacity. Temperature-programmed reduction results indicated that Tb or Zr incorporation improves the reducibility and oxygen storage capacity. CO chemisorption data suggested the presence of large PdO particles due to the low CO/Pd ratio. No significant differences were obtained in light off temperatures (T_{Light off}) for all Pd catalysts and the most active was 1.5%Pd/Ce_0.6Zr_0.4O_x/SiO₂.     

The selective catalytic reduction of NO over Ce0.3TiOx-supported metal oxide catalysts

A Ce_(0.3)TiO_xoxide carrier was synthesized via a sol–gel process,and Ce_(0.3)TiO_xsupported metal(M=Cd,Mn,Fe,W,Mo)oxide catalysts were prepared by the method of incipient-wetness impregnation.The catalysts were characterized by means of X-ray diffraction(XRD),Brunauer–Emmett–Teller(BET)analysis,scanning electron microscopy(SEM),transmission electron microscopy(TEM),Fourier transform infrared(FT–IR)spectroscopy,UV–Visdiffusereflectancespectroscopy(UV–VisDRS),and Temperature-programmed reduction with H_2(H_2-TPR).The catalytic activities for de-NO_(x )were evaluated by the NH_3-SCR reaction.Among all the catalysts tested,the 2 wt.%Cd/Ce_(0.3)TiO_xcatalyst exhibited the best NH_3-SCR performance,with a wide temperature window of 250–450°C for NO conversion above 90%.Moreover,the catalyst showed N_2 selectivity greater than 99%from 200 to 450°C.     

富氧条件下SnO2/Al2O3催化剂上丙烯选择性还原NOx的研究

考察了分别用浸渍法、共沉淀法和溶胶-凝胶法制备的SnO₂/Al₂O₃催化剂上丙烯选择性还原NO_x的催化活性,发现制备方法与Sn的负载量对其活性有重要影响.溶胶-凝胶法制备的SnO₂/Al₂O₃催化剂活性最高,Sn的最佳负载量为5%.与浸渍法和共沉淀法制备的5%SnO₂/Al₂O₃催化剂相比,溶胶-凝胶法制备的5%SnO₂/Al₂O₃催化剂受水蒸汽的抑制作用较弱,并且在水和SO₂共存的条件下活性最高.此外,反应气中丙烯及氧气浓度的增加有利于NO_x转化率的提高.     

Effect of Ce doping of TiO2 support on NH3-SCR activity over V2O5-WO3/CeO2-TiO2 catalyst

CeO2–TiO2composite supports with different Ce/Ti molar ratios were prepared by a homogeneous precipitation method, and V2O5–WO3/CeO2–TiO2catalysts for the selective catalytic reduction（SCR） of NOx with NH3 were prepared by an incipient-wetness impregnation method. These catalysts were characterized by means of BET, XRD, UV–Vis,Raman and XPS techniques. The results showed that the catalytic activity of V2O5–WO3/TiO2 was greatly enhanced by Ce doping（molar ratio of Ce/Ti = 1/10） in the TiO2 support.The catalysts that were predominantly anatase TiO2 showed better catalytic performance than the catalysts that were predominantly fluorite CeO2. The Ce additive could enhance the surface adsorbed oxygen and accelerate the SCR reaction. The effects of O2 concentration, ratio of NH3/NO, space velocity and SO2 on the catalytic activity were also investigated. The presence of oxygen played an important role in NO reduction. The optimal ratio of NH3/NO was 1/1 and the catalyst had good resistance to SO2 poisoning.     

N/Ce doped graphene supported Pt nanoparticles for the catalytic oxidation of formaldehyde at room temperature

Pt catalysts with nitrogen-doped graphene oxide (GO) as support and CeO₂ as promoter were prepared by impregnation method,and their catalytic oxidation of formaldehyde (HCHO) at room temperature was tested.The Pt-CeO₂/N-rGO (reduced GO) with a mass fraction of 0.7% Pt and 0.8%CeO₂ exhibited an excellent catalytic performance with the 100% conversion of HCHO at room temperature.Physicochemical characterization demonstrated that nitrogendoping greatly increased the...     

Pd/TiO2对水体中2,4-二氯酚的催化加氢脱氯研究

分别采用沉淀-沉积法和浸渍法合成了Pd/TiO2催化剂,采用透射电镜(TEM)、X射线衍射(XRD)和电感耦合等离子体发射光谱(ICP-AES)对材料进行了表征,并对2,4-二氯酚的催化加氢脱氯反应进行了研究.结果表明,2种方法制备的催化剂在加氢脱氯反应中均具有较好的效果,沉淀-沉积法制备的催化剂活性更高,当反应物初始浓度为3.11 mmol.L-1,pH为12,催化剂用量为50 mg时,45 min内2,4-二氯酚可以完成脱氯过程.酸性条件有利于反应的进行.当催化剂用量在15～80 mg时,反应初活性没有明显变化,因此催化反应过程不受传质阻力的影响.当反应物初始浓度在0.62～3.11 mmol.L-1时反应初活性随浓度的提高显著增加,但进一步增加反应物的浓度时初活性没有明显提高,因此2,4-二氯酚在催化剂上的加氢脱氯行为符合Langmuir-Hinshelwood模型,表明2,4-二氯酚的加氢脱氯受表面吸附所控制.     

Improved activity and durability of Rh-based three-way catalyst under diverse aging atmospheres by ZrO2 support

The catalytic activity and durability of Rh/ZrO_2 catalyst were investigated compared with Rh/Al_2O_3 catalyst under diverse aging atmospheres, including lean, rich and lean–rich cyclic aging atmospheres, to simulate the real working conditions of three-way catalyst.Oxidation states and microstructures of rhodium species were investigated to correlate with the catalytic performance of the catalysts. The catalytic performance and durability of the Rh catalyst under diverse aging atmospheres were drastically enhanced by ZrO_2 support. ZrO_2 support was confirmed to be able to effectively inhibit rhodium sintering even under diverse aging conditions. It can also successfully keep Rh species in an active low-valence state on the surface of the catalyst. The superiority of ZrO_2 support compared to Al_2O_3 was verified by the Rh-based monolith catalyst.     

Promotional effect of Si-doped V2O5/TiO2 for selective catalytic reduction of NOx by NH3

TiO2 supports doped with different amounts of Si were prepared by a sol-gel method, and 1 wt% vanadia (V2O5) loaded on Si-doped TiO2 was obtained by an impregnation method. The mole ratio of Si/Ti was 0.2, NOx conversion exceeds 94% at 300℃ and GHSV of 41,324 hr-1 , which is about 20% higher than pure V2O5/TiO2 . The catalysts were characterized by XRD, BET, TEM, FT-IR, NH3-TPD, XPS, H2-TPR, Raman and in situ DRIFTS. The results of FT-IR and XPS indicated that Si was doped into the TiO2 lattice successfully and a solid solution was obtained. V2O5 active component could be dispersed well on the support with the increasing of surface area of the catalyst, which was confirmed by Raman and XRD results. Above all, the numbers of acid sites (especially the Br nsted-acid) and oxidation properties were enhanced for Si-doped V2O5/TiO2 catalysts, which improved the deNOx catalytic activity.     

Effect of chromium oxide as active site over TiO2-PILC for selective catalytic oxidation of NO

This study introduced TiO2-pillared clays （TiO2-PILC） as a support for the catalytic oxidation of NO and analyzed the performance of chromium oxides as the active site of the oxidation process. Cr-based catalysts were prepared by a wet impregnation method. It was found that the 10 wt.% chromium doping on the support achieved the best catalytic activity. At 350℃, the NO conversion was 61% under conditions of GHSV = 23600 hr^-l. The BET data showed that the support particles had a mesoporous structure. Hz-TPR showed that Cr（10）TiP （10 wt.% Cr doping on TiO2-PILC） clearly exhibited a smooth single peak. EPR and XPS were used to elucidate the oxidation process. During the NO ＋ O2 adsorption, the intensity of evolution of superoxide ions （O2^-） increased. The content of Cr^3＋ on the surface of the used catalyst was 40.37%, but when the used catalyst continued adsorbing NO, the Cr^3＋ increased to 50.28%. Additionally, Oα/Oβ increased markedly through the oxidation process. The NO conversion decreased when SO2 was added into the system, but when the SO2 was removed, the catalytic activity recovered almost up to the initial level. FT-IR spectra did not show a distinct characteristic peak of SO4^2-.     

Fe2O3 particles as superior catalysts for low temperature selective catalytic reduction of NO with NH3

Fe203 particle catalysts were experimentally studied in the low temperature selective catalytic reduction （SCR） of NO with NH3. The effects of reaction temperature, oxygen concentration, [NH3]/[NO] molar ratio and residence time on SCR activity were studied. It was found that Fe203 catalysts had high activity for the SCR of NO with NH3 in a broad temperature range of 150-270℃, and more than 95% NO conversion was obtained at 180℃ when the molar ratio [NH3]/[NO] = 1, the residence time was 0.48 seconds and 02 volume fraction was 3%. In addition, the effect of SO2 on SCR catalytic activity was also investigated at the temperature of 180℃. The results showed that deactivation of the Fe2O3 particles occurred due to the presence of SO2 and the NO conversion decreased from 99.2% to 58% in 240 min, since SO2 gradually decreased the catalytic activity of the catalysts. In addition, X-ray diffraction, Thermogravimetric analysis and Fourier transform infrared spectroscopy were used to characterize the fresh and deactivated Fe2O3 catalysts. The results showed that the deactivation caused by SO2 was due to the formation of metal sulfates and ammonium sulfates on the catalyst surface during the de-NO reaction, which could cause pore plugging and result in suppression of the catalytic activity.     

Mo-modified Pd/Al2O3 catalysts for benzene catalytic combustion

Mo-modified Pd/Al2O3catalysts were prepared by an impregnation method and tested for the catalytic combustion of benzene. The catalysts were characterized by N2 isothermal adsorption, X-ray diffraction（XRD）, X-ray photoelectron spectroscopy（XPS）, temperatureprogrammed desorption of NH3（NH3-TPD）, H2temperature-programmed reduction（H2-TPR）, and high-angle annular dark-field scanning transmission electron microscopy（HAADF-STEM）. The results showed that the addition of Mo effectively improved the activity and stability of the Pd/Al2O3catalyst by increasing the dispersion of Pd active components, changing the partial oxidation state of palladium and increasing the oxygen species concentration on the surface of catalyst. In the case of the Pd-Mo/Al2O3catalyst,benzene conversion of 90% was obtained at temperatures as low as 190°C, which was 45°C lower than that for similar performance with the Pd/Al2O3catalyst. Moreover, the 1.0% Pd-5% Mo/Al2O3catalyst was more active than the 2.0% Pd/Al2O3catalyst. It was concluded that Pd and Mo have a synergistic effect in benzene catalytic combustion.     

Synthesis of novel CeO2-BiVO4/FAC composites with enhanced visible-light photocatalytic properties

To utilize visible light more effectively in photocatalytic reactions, a fly ash cenosphere （FAC）-supported CeO2-BiV04 （CeO2-BiVO4/FAC） composite photocatalyst was prepared by modified metalorganic decomposition and impregnation methods. The physical and photophysical properties of the composite have been characterized by X-ray diffraction （XRD）, scanning electron microscope （SEM） and energy dispersive X-ray spectroscopy （EDX）, X-ray photoelectron spectroscopy （XPS）, and UV-Visible diffuse reflectance spectra. The XRD patterns exhibited characteristic diffraction peaks of both BiVO4 and Ce02 crystalline phases. The XPS results showed that Ce was present as both Ce4＋ and Ce3＋ oxidation states in Ce02 and dispersed on the surface of BiV04 to constitute a p-n heterojunction composite. The absorption threshold of the CeO2-BiVO4/FAC composite shifted to a longer wavelength in the UV-Vis absorption spectrum compared to the pure Ce02 and pure BiV04. The composites exhibited enhanced photocatalytic activity for Methylene Blue （MB） degradation under visible light irradiation. It was found that the 7.5 wt.% CeO2-BiVO4/FAC composite showed the highest photocatalytic activity for MB dye wastewater treatment.     

Effect of pretreatment on Pd/Al2O3 catalyst for catalytic oxidation of o-xylene at low temperature

The effect of pretreatment on Pd/Al₂O₃ catalysts for the catalytic oxidation of o-xylene at low temperature was studied by changing the pretreatment and testing conditions. The fresh and pretreated Pd/Al₂O₃ catalysts were characterized by transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD). The results showed that the pretreatment dramatically changed the Pd/PdO ratio and then significantly affected the Pd/Al₂O₃ activity; while the pretreatment had not much influence on Pd particle size. The Pd/Al₂O₃ pre-reduced at 300℃/400℃, which has fully reduced Pd species, showed the highest activity; while the fresh Pd/Al₂O₃, which has fully oxidized Pd species, presented the worst performance, indicating the Pd chemical state plays an important role in the catalytic activity for the o-xylene oxidation. It is concluded that metallic Pd is the active species on the Pd/Al₂O₃ catalyst for the catalytic oxidation of o-xylene at low temperature.     

N2O decomposition over K/Na-promoted Mg/Zn-Ce-cobalt mixed oxides catalysts

Three groups of cobalt mixed oxide catalysts（Mg/Zn-Co, Mg/Zn-Ce-C, K/Na-Mg/Zn-Ce-Co）were prepared by sol-gel or impregnation methods. The synergistic effects of transition metal, rare earth metal and alkali metal on cobalt mixed catalysts for nitrous oxide（N2O）decomposing to N2 and O2were investigated. The experimental results revealed that the catalytic activity for N2 O decomposition was promoted as Co2＋was replaced partially by Zn2＋/Mg2＋, moreover, the characterization analysis by XRD and XPS showed that Zn2＋/Mg2＋replaced Co2＋successfully into the spinel structure of Co3O4 and promoted significantly the catalytic activity. Especially, the addition of CeO2 and K2O/Na2O decreased the binding energy and resulted in an increase in the density of the electron cloud around Co and an improvement of the catalytic activity. Of the investigated cobalt mixed catalysts, the best catalytic activity was shown by 2% K-Zn0.5-Ce0.05-Co catalyst.     

Characterization and performance of Pt/SBA-15 for low-temperature SCR of NO by C3H6

Pt supported on mesoporous silica SBA-15 was investigated as a catalyst for low temperature selective catalytic reduction(SCR) of NO by C 3 H 6 in the presence of excess oxygen.The prepared catalysts were characterized by means of XRD,BET surface area,TEM,NO-TPD,NO/C 3 H 6-TPO,NH 3-TPD,XPS and 27 Al MAS NMR.The effects of Pt loading amount,O 2 /C 3 H 6 concentration,and incorporation of Al into SBA-15 have been studied.It was found that the removal efficiency increased significantly after Pt loading,but an optimal loading amount was observed.In particular,under an atmosphere of 150 ppm NO,150 ppm C 3 H 6,and 18 vol.% O 2,0.5% Pt/SBA-15 showed remarkably high catalytic performance giving 80.1% NOx reduction and 87.04% C 3 H 6 conversion simultaneously at 140°C.The enhanced SCR activity of Pt/SBA-15 is associated with its outstanding oxidation activities of NO to NO 2 and C 3 H 6 to CO 2 in low temperature range.The research results also suggested that higher concentration of O 2 and higher concentration of C 3 H 6 favored NO removal.The incorporation of Al into SBA-15 improved catalytic performance,which could be ascribed to the enhancement of catalyst surface acidity caused by tetrahedrally coordinated AlO 4.Moreover,the catalysts could be easily reused and possessed good stability.     

Ultrasound-assistant preparation of Cu-SAPO-34 nanocatalyst for selective catalytic reduction of NO by NH3

The influence of the various preparation methods of Cu-SAPO-34 nanocatalysts on the selective catalytic reduction of NO with NH₃ under excess oxygen was studied. Cu-SAPO-34 nanocatalysts were prepared by using four techniques: conventional impregnation (IM), ultrasound-enhanced impregnation (UIM), conventional deposition precipitation (DP) using NaOH and homogeneous deposition precipitation (HDP) using urea. These catalysts were characterized in detail by various techniques such as N₂-sorption, XRD, TEM, H₂-TPR, NH₃-TPD and XPS to understand the catalyst structure, the nature and the dispersed state of the copper species, and the acid sites for NH₃ adsorption. All of the nanocatalysts showed high activities for NO removal. However, the activities were different and followed the sequence of Cu-SAPO-34 (UIM) > Cu-SAPO-34 (HDP) > Cu-SAPO-34 (IM) > Cu-SAPO-34 (DP). Based on the obtained results, it was concluded that the NO conversion on Cu-SAPO-34 nanocatalysts was mainly related to the high reducibility of the isolated Cu^2 + ions and CuO species, the number of the acid sites and the dispersion of CuO species on SAPO-34.     

A comparative investigation of NdSrCu1-xCoxO4-σ and Sm1:8Ce0:2Cu1-xCoxO4-σ(x: 0-0.4) for NO decomposition

A series of single-phase T-structured NdSrCu1??xCoxO4?? with oxygen vacancies and T0-structured Sm1:8Ce0:2Cu1??xCoxO4?? (x: 0–0.4) with oxygen excess were prepared using ultrasound-assisted citric acid complexing method, and characterized by means of techniques such as thermogravimetric analysis and NO temperature-programmed desorption (NO-TPD). The catalytic activities of these materials were evaluated for the decomposition of NO. It was found that the NdSrCu1??xCoxO4?? catalysts were of oxygen vacancies whereas the Sm1:8Ce0:2Cu1??xCoxO4?? ones possessed excessive oxygen (i.e., over-stoichiometric oxygen); with a rise in Co doping level, the oxygen vacancy density of NdSrCu1??xCoxO4?? decreased while the over-stoichiometric oxygen amount of Sm1:8Ce0:2Cu1??xCoxO4?? increased. The NO-TPD results revealed that NO could be activated much easier over the oxygen-deficient perovskite-like oxides than over the oxygen-excessive perovskite-like oxides, with the NdSrCuO3:702 catalyst showing the best e ciency in activating NO molecules. Under the conditions of 1.0% NO/helium, 2800 hr??1, and 600–900°C, the catalytic activity of NO decomposition followed the order of NdSrCuO3:702 > NdSrCu0:8Co0:2O3:736 > NdSrCu0:6Co0:4O3:789 > Sm1:8Ce0:2Cu0:6Co0:4O4:187 > Sm1:8Ce0:2Cu0:8Co0:2O4:104 > Sm1:8Ce0:2CuO4:045, in concord with the sequence of decreasing oxygen vacancy or oxygen excess density. Based on the results, we concluded that the higher oxygen vacancy density and the stronger Cu3+/Cu2+ redox ability of NdSrCu1??xCoxO4?? account for the easier activation of NO and consequently improve the catalytic activity of NO decomposition over the catalysts.     

富氧条件下Ag、Co和Cu/Al2O3选择性催化还原NO的研究

研究了负载于氧化铝载体上的Ag、Co和Cu 3种金属催化剂在富氧条件下以丙烯为还原剂,选择性催化还原NO的活性,考察了这3种金属单独负载时其负载量与活性的关系,并尝试探讨了这几种金属活性组分之间的一些组合效应.研究表明,单组分催化剂以Ag的活性最佳,达近90%,Co其次,Cu最低.相应的最佳活性温度则是Cu最低,Ag最高.对于单组分Ag催化剂,相同负载量的分步浸渍与一步浸渍样品活性无明显差异.机械混合样品的活性不是单组分样品活性的简单加和.其中,以Ag-Co机械混合样品的活性最佳,最高活性高于80%.复合催化剂一步浸渍与分步浸渍样品的活性均有不同程度的下降,一步浸渍的几个样品的活性下降尤为明显,最高活性只有30%多.