Comparative equilibrium studies of sorption of Pb(Ⅱ) ions by sodium and calcium alginate

The absorption of Pb(Ⅱ) ions from aqueous solution by different alginate compounds was studied in a batch sorption system.Water soluble sodium alginate and insoluble calcium alginate beads were investigated.The lead-binding capacity of both alginate compounds was highest within the pH range 6-8.The binding capacities and rates of Pb(lI) ions by alginate compounds were evaluated.The Langmuir,Freundlich,and Bruneaur,Emmet and Teller (BET) sorption models were applied to describe the isotherms and isotherm ...     

微生物吸附剂对重金属的吸附特性

从活性污泥中分离得到5株菌,检验了它们对重金属离子的吸附能力,其中类产碱假单胞菌(Pseudomonas pseudoalcaligenes)和藤黄微球菌(Micrococcus luteus)GC subgroup B对Cu(Ⅱ)和Pb(Ⅱ)离子吸附能力最强.考察了Cu(Ⅱ)和Pb(Ⅱ)离子分别在这2种菌体上的吸附特性研究表明,Langmuir型吸附模式能很好地描述Cu(Ⅱ)和Pb(Ⅱ)离子在这2种菌体上的吸附实验数据,其线形回归系数高达0.99,溶液pH值是影响吸附的最主要因素,pH=5～6是吸附Cu(Ⅱ)和Pb(Ⅱ)离子的适宜条件.吸附动力学实验研究表明,菌体对Cu(Ⅱ)和Pb(Ⅱ)离子的吸附可以分为迅速的细胞表面结合和缓慢的向细胞内的传输,稀HNO₃和H₂SO₄是Cu(Ⅱ)离子从Micrococcus luteus GC subgroup B菌体上有效的洗脱剂.     

Sequestration of toxic Pb（II） ions by chemically treated rubber （Hevea brasiliensis ） leaf powder

Rubber leaf powder (an agricultural waste) was treated with potassium permanganate followed by sodium carbonate and its performance in the removal of Pb(II) ions from aqueous solution was evaluated. The interactions between Pb(II) ions and functional groups on the adsorbent surface were confirmed by Fourier transform infrared (FT-IR) spectroscopy, scanning electron microscopy (SEM) coupled with X-ray energy dispersive spectroscopy (EDX). The effects of several important parameters which can affect adsorption capacity such as pH, adsorbent dosage, initial lead concentration and contact time were studied. The optimum pH range for lead adsorption was 4–5. Even at very low adsorbent dosage of 0.02 g, almost 100% of Pb(II) ions (23 mg/L) could be removed. The adsorption capacity was also dependent on lead concentration and contact time, and relatively a short period of time (60–90 min) was required to reach equilibrium. The equilibrium data were analyzed with Langmuir, Freundlich and Dubinin-Radushkevich isotherms. Based on Langmuir model, the maximum adsorption capacity of lead was 95.3 mg/g. Three kinetic models including pseudo first-order, pseudo second-order and Boyd were used to analyze the lead adsorption process, and the results showed that the pseudo second-order fitted well with correlation coefficients greater than 0.99.     

Pb(Ⅱ) biosorption using chitosan and chitosan derivatives beads: Equilibrium,ion exchange and mechanism studies

The study examined the adsorption of Pb(II) ions from aqueous solution onto chitosan, chitosan-GLA and chitosan-alginate beads. Several important parameters influencing the adsorption of Pb(II) ions such as initial pH, adsorbent dosage and different initial concentration of Pb(II) ions were evaluated. The mechanism involved during the adsorption process was explored based on ion exchange study and using spectroscopic techniques. The adsorption capacities obtained based on non-linear Langmuir isotherm for ch...     

Pb（II） biosorption using chitosan and chitosan derivatives beads： Equilibrium, ion exchange and mechanism studies

The study examined the adsorption of Pb(II) ions from aqueous solution onto chitosan, chitosan-GLA and chitosan-alginate beads. Several important parameters influencing the adsorption of Pb(II) ions such as initial pH, adsorbent dosage and di erent initial concentration of Pb(II) ions were evaluated. The mechanism involved during the adsorption process was explored based on ion exchange study and using spectroscopic techniques. The adsorption capacities obtained based on non–linear Langmuir isotherm for chitosan, chitosan-GLA and chitosan-alginate beads in single metal system were 34.98, 14.24 and 60.27 mg/g, respectively. However, the adsorption capacity of Pb(II) ions were reduced in the binary metal system due to the competitive adsorption between Pb(II) and Cu(II) ions. Based on the ion exchange study, the release of Ca2+, Mg2+, K+ and Na+ ions played an important role in the adsorption of Pb(II) ions by all three adsorbents but only at lower concentrations of Pb(II) ions. Infrared spectra showed that the binding between Pb(II) ions and the adsorbents involved mostly the nitrogen and oxygen atoms. All three adsorbents showed satisfactory adsorption capacities and can be considered as an e cient adsorbent for the removal of Pb(II) ions from aqueous solutions.     

Effect of pH on transport of Pb（2＋）,Mn（2＋）,Zn（2＋）and Ni（2＋） through lateritic soil： Column experiments and transport modeling

This study investigated the e ects of pH on the transport of Pb2+, Mn2+, Zn2+ and Ni2+ through lateritic soil columns. Model results by fitting the symmetric breakthrough curves (BTCs) of bromide (Br??) with CXTFIT model suggested that physical non-equilibrium processes were absent in the columns. The heavy metal BTCs were, however, asymmetrical and exhibited a tailing phenomenon, indicating the presence of chemical non-equilibrium processes in the columns. The retardation factors of Pb2+ were the largest of the four metal ions at both pH 4.0 (33.3) and pH 5.0 (35.4). The use of Langmuir isotherm parameters from batch studies with HYDRUS-1D did not predict the BTCs well. Rather the two-site model (TSM) described the heavy metal BTCs better than the equilibrium linear/nonlinear Langmuir model. The fraction of instantaneous sorption sites ( f ) of all four metal ions on the lateritic soil was consistently about 30%–44% of the total sorption sites.     

Immobilization study of biosorption of heavy metal ions onto activated sludge

Activated sludge was immobilized into Ca-alginate beads via entrapment, and biosorption of three heavy metal ions, copper(Ⅱ), zinc(Ⅱ), and chromimum(Ⅱ), from aqueous solution in the concentration range of 10-100 mg/L was studied by using both entrapped activated sludge and inactivated free biomass at pH≤5. A biphasic metal adsorption pattern was observed in all immobilized biomass experiments. The biosorption of metal ions by the biosorbents increased with the initial concentration increased in the medium. The adsorption rate of immobilized pre-treated activated sludge(PAS) was much lower than that of free PAS due to the increase in mass transfer resistance resulting from the polymeric matrix. Biosorption equilibrium of beads was established in about 20 h and the adsorbed heavy metal ions did not change further with time. No significant effect of temperature was observed in the test for free biomass while immobilized PAS appeared to be strong temperature dependent in the test range of 10 and 40℃.Besides, the content of activated sludge in the calcium alginate bead has an influence on the uptake of heavy metals. The sorption equilibrium was well modeled by Langmuir isotherm, implying monomolecular adsorption mechanism. Carboxyl group in cell wall played an important role in surface adsorption of heavy metal ions on PAS.     

海藻酸钠包埋活性炭与细菌的条件优化及其对Pb~(2+)的吸附特征研究

利用海藻酸钠固定化包埋活性炭与多黏类芽孢杆菌GA1,通过正交试验研究海藻酸钠溶液浓度、包炭量及包菌量吸附Pb2+的最佳配比,并研究了这种新型的固定化小球对Pb2+的吸附特征.结果表明,固定化活性炭与多黏类芽孢杆菌GA1小球最佳制备条件为海藻酸钠质量分数2.5%、包炭量1:20和包菌量1:2,在该制备条件下吸附率达到93.74%.固定化小球的最佳吸附条件为pH5、温度30℃和Pb2+初始浓度300mg·L-1,活性炭与GA1经固定后对pH、温度和Pb2+初始浓度适应范围扩大.吸附平衡曲线表明,对Pb2+的吸附在30min内是一个快速的过程,在2h时基本趋于平衡,且平衡曲线能较好地用Langmuir模型和Freundlich模型来描述,其吸附过程主要为单分子层吸附,最大单分子层吸附量为370.37mg·g-1.解吸结果表明固定化小球能有效地循环利用.     

Synthesis, characterization, and adsorption performance of Pb（Ⅱ）-imprinted polymer in nano-TiO2 matrix

Surface ion-imprinted in combination with sol-gel process was applied to synthesis a new Pb(II)-imprinted polymer for selective separation and enrichment of trace Pb(II) from aqueous solution. The prepared material was characterized by using the infrared spectra, X-ray di ractometer, and scanning electron microscopy. The batch experiments were conducted to study the optimal adsorption condition of adsorption trace Pb(II) from aqueous solutions on Pb(II)-imprinted polymer. The equilibrium was achieved in approximately 4.0 h, and the experimental kinetic data were fitted the pseudo second-order model better. The maximum adsorption capacity was 22.7 mg/g, and the Langmuir equation fitted the adsorption isotherm data. The results of selectivity experiment showed that selectively adsorbed rate of Pb(II) on Pb(II)-imprinted polymer was higher than all other studied ions. Desorption conditions of the adsorbed Pb(II) from the Pb(II)-imprinted polymer were also studied in batch experiments. The prepared Pb(II)-imprinted polymer was shown to be promising for the separation and enrichment of trace Pb(II) from water samples. The adsorption and desorption mechanisms were proposed.     

Adsorption characteristics of copper, lead, zinc and cadmium ions by tourmaline

The adsorption characteristics of heavy metals： Cu（Ⅱ）, Pb（Ⅱ）, Zn（Ⅱ） and Cd（Ⅱ） ions on tourmaline were studied. Adsorption equilibrium was established. The adsorption isotherms of all the four metal ions followed well Langmuir equation. Tourmaline was found to remove heavy metal ions efficiently from aqueous solution with selectivity in the order of Pb（Ⅱ）〉Cu（Ⅱ）〉Cd（Ⅱ）〉Zn（Ⅱ）. The adsorption of metal ions by tourmaline increased with the initial concentration of metal ions increasing in the medium. Tourmaline could also increase pH value of metal solution.The maximum heavy metal ions adsorbed by tourmaline was found to be 78.86, 154.08, 67.25, and 66.67 mg/g for Cu（Ⅱ）, Pb（U）, Zn（Ⅱ） and Cd（U）, respectively. The temperature （25-55℃） had a small effect on the adsorption capacity of tourmaline. Competitive adsorption of Cu（Ⅱ）, Pb（Ⅱ）, Zn（Ⅱ） and Cd（Ⅱ） ions was also studied. The adsorption capacity of tourmaline for single metal decreased in the order of Pb〉Cu〉Zn 〉Cd and inhibition dominance observed in two metal systems was Pb〉Cu, Pb〉Zn, Pb〉Cd, Cu〉Zn, Cu〉Cd, and Cd〉Zn.     

Biosorption of cadmium(II) and lead(II) ions from aqueous solutions onto dried activated sludge

Introduction Toxic metal compounds are frequently used in industrial processes and are widely distributed in the environment. Due to their extended persistence in biological systems and tendency to bioaccumulate as they move up the food chain, they repres…     

Adsorptive removal of heavy metal ions from industrial effluents using activated carbon derived from waste coconut buttons

Removal of heavy metal ions from industrial effluents by the activated carbon prepared by steam activation of waste coconut buttons through batch adsorption process.     

菌株Dyella ginsengisoli LA-4吸附Ni~(2+)的条件优化及特性研究

主要考察了菌株Dyella ginsengisoli LA-4对重金属Ni2+的吸附性能,同时,利用表面响应法对菌株Dyella ginsengisoli LA-4吸附Ni2+的条件(接种量、pH、Ni2+浓度等)进行了优化,并考察了其动力学及吸附等温曲线特性.实验结果表明,菌株Dyella ginsengisoli LA-4吸附Ni2+的最优条件为:接种量10.64 g.L-1,pH为6.50,Ni2+浓度为19.20 mg.L-1,此时的Ni2+最大去除率为99%.动力学分析表明,吸附平衡时间约为30 min,吸附可分为表面快速吸附和缓慢重金属积累两个阶段.利用Langmuir吸附模型能较好地描述菌株Dyella ginsengisoli LA-4对Ni2+的等温吸附行为,最大吸附量为25.81 mg.g-1.     

竞争干扰对轮叶黑藻吸附Pb(Ⅱ)的影响

沉水植物处理低浓度重金属废水是一项清洁和廉价的技术.主要研究了不同初始浓度和pH条件下,轮叶黑藻鲜样在单一、二元和三元金属离子体系中对铅离子的生物吸附特征.在单一金属离子体系中,不同pH值条件下的实验结果表明,pH值在2.0～6.0间变化时,轮叶黑藻对铅的吸附能力随pH值升高而增强,当初始铅浓度为250 mg/L和pH...     

Sequestration of toxic Pb(Ⅱ) ions by chemically treated rubber(Hevea brasiliensis) leaf powder

Rubber leaf powder(an agricultural waste) was treated with potassium permanganate followed by sodium carbonate and its performance in the removal of Pb(Ⅱ) ions from aqueous solution was evaluated.The interactions between Pb(Ⅱ) ions and functional groups on the adsorbent surface were confirmed by Fourier transform infrared(FT-IR) spectroscopy,scanning electron microscopy(SEM) coupled with X-ray energy dispersive spectroscopy(EDX).The effects of several important parameters which can affect adsorption capacity such as pH,adsorbent dosage,initial lead concentration and contact time were studied.The optimum pH range for lead adsorption was 4-5.Even at very low adsorbent dosage of 0.02 g,almost 100% of Pb(Ⅱ) ions(23 mg/L) could be removed.The adsorption capacity was also dependent on lead concentration and contact time,and relatively a short period of time(60-90 min) was required to reach equilibrium.The equilibrium data were analyzed with Langmuir,Freundlich and Dubinin-Radushkevich isotherms.Based on Langmuir model,the maximum adsorption capacity of lead was 95.3 mg/g.Three kinetic models including pseudo first-order,pseudo second-order and Boyd were used to analyze the lead adsorption process,and the results showed that the pseudo second-order fitted well with correlation coefficients greater than 0.99.     

Biosorption of cadmium(Ⅱ) and lead(Ⅱ) ions from aqueous solutions onto dried activated sludge

The removal of heavy-metal ions from aqueous solutions by using dried activated sludge has been investigated in batch systems. Effect of solution pH, initial metal ion concentration, and temperature were determined. The results of the kinetic studies showed that the uptake processes of the two metal ions（Cd（Ⅱ） and Pb（Ⅱ）） followed the pseudo-second-order rate expression. The equilibrium data fitted very well to both the Langmuir and Freundlich adsorption models. The FT-IR analysis showed that the main mechanism of Cd（Ⅱ） and Pb（Ⅱ） biosorption onto dried activated sludge was their binding with amide I group.     

Equilibrium and kinetics of copper(Ⅱ) biosorption by Myriophyllum spicatum L.

The potential use of Myriophyllum spicatum L. biomass as a biosorbent for the removal of copper（ Ⅱ ） from aqueous solution was investigated in laboratory condition. The sorption experiments were undertaken to obtain copper（ Ⅱ ） biosorption properties of M. spicatum L., i.e. equilibrium time, the maximum capacity, and rate constants. Copper（ Ⅱ ） biosorption was fast and equilibrium was attained within 35 min at initial copper（ Ⅱ ） concentration of 6 mg/L. Different isotherm models including the Langmuir, Freundlich, Temkin and Redlich-Peterson model, were used to investigate the sorption capacity and isotherm. These models showed an excellent match with the experimental data except for the Freundlich model. According to the Langmuir coefficients, the maximum sorption capacity of copper onto M. spicatum L. was 10.80 mg/g. The kinetics of copper（ Ⅱ ） sorption was also analysed and rate constants were derived. It was found that the overall sorption process was best described by the pseudo second-order equation, and that intraparticle diffusion was not the rate determining step. The results of this study showed that M. spicatum L. can be considered as useful vehicles for the removal and recovery of copper（ Ⅱ ） from aqueous solutions.     

Enhanced U(VI) bioreduction by alginate-immobilized uranium-reducing bacteria in the presence of carbon nanotubes and anthraquinone-2,6-disulfonate

Uranium-reducing bacteria were immobilized with sodium alginate, anthraquinone-2, 6-disulfonate (AQDS), and carbon nanotubes (CNTs). The effects of different AQDS-CNTs contents, U(IV) concentrations, and metal ions on U(IV) reduction by immobilized beads were examined. Over 97.5% U(VI) (20 mg/L) was removed in 8 hr when the beads were added to 0.7% AQDS-CNTs, which was higher than that without AQDS-CNTs. This result may be attributed to the enhanced electron transfer by AQDS and CNTs. The reduction of U(VI) occurred at initial U(VI) concentrations of 10 to 100 mg/L and increased with increasing AQDS-CNT content from 0.1% to 1%. The presence of Fe(III), Cu(II) and Mn(II) slightly increased U(VI) reduction, whereas Cr(VI), Ni(II), Pb(II), and Zn(II) significantly inhibited U(VI) reduction. After eight successive incubation-washing cycles or 8 hr of retention time (HRT) for 48 hr of continuous operation, the removal efficiency of uranium was above 90% and 92%, respectively. The results indicate that the AQDS-CNT/AL/cell beads are suitable for the treatment of uranium-containing wastewaters.     

Adsorptive removal of iron and manganese ions from aqueous solutions with microporous chitosan/polyethylene glycol blend membrane

Microporous chitosan (CS) membranes were directly prepared by extraction of poly(ethylene glycol) (PEG) from CS/PEG blend membrane and were examined for iron and manganese ions removal from aqueous solutions. The different variables affecting the adsorption capacity of the membranes such as contact time, pH of the sorption medium, and initial metal ion concentration in the feed solution were investigated on a batch adsorption basis. The affinity of CS/PEG blend membrane to adsorb Fe(II) ions is higher than that of Mn(II) ions, with adsorption equilibrium achieved after 60 min for Fe(II) and Mn(II) ions. By increasing CS/PEG ratio in the blend membrane the adsorption capacity of metal ions increased. Among all parameters, pH has the most significant effect on the adsorption capacity, particularly in the range of 2.9-5.9. The increase in CS/PEG ratio was found to enhance the adsorption capacity of the membranes. The effects of initial concentration of metal ions on the extent of metal ions removal were investigated in detail. The experimental data were better fitted to Freundlich equation than Langmuir. In addition, it was found that the iron and manganese ions adsorbed on the membranes can be effectively desorbed in 0.1 mol/L HCl solution (up to 98% desorption efficiency) and the blend membranes can be reused almost without loss of the adsorption capacity for iron and manganese ions.     

Synthesis of linear low-density polyethylene-g-poly (acrylic acid)-co-starch/organo-montmorillonite hydrogel composite as an adsorbent for removal of Pb(Ⅱ) from aqueous solutions

The purpose of this work is to remove Pb(II) from the aqueous solution using a type of hydrogel composite. A hydrogel composite consisting of waste linear low density polyethylene, acrylic acid, starch, and organo-montmorillonite was prepared through emulsion polymerization method. Fourier transform infrared spectroscopy (FTIR), Solid carbon nuclear magnetic resonance spectroscopy (CNMR)), silicon^-29 nuclear magnetic resonance spectroscopy (Si NMR)), and X-ray diffraction spectroscope ((XRD) were applied to characterize the hydrogel composite. The hydrogel composite was then employed as an adsorbent for the removal of Pb(II) from the aqueous solution. The Pb(II)-loaded hydrogel composite was characterized using Fourier transform infrared spectroscopy (FTIR)), scanning electron microscopy (SEM)), and X-ray photoelectron spectroscopy ((XPS)). From XPS results, it was found that the carboxyl and hydroxyl groups of the hydrogel composite participated in the removal of Pb(II). Kinetic studies indicated that the adsorption of Pb(II) followed the pseudo-second-order equation. It was also found that the Langmuir model described the adsorption isotherm better than the Freundlich isotherm. The maximum removal capacity of the hydrogel composite for Pb(II) ions was 430 mg/g. Thus, the waste linear low-density polyethylene-g-poly (acrylic acid)-co-starch/organo-montmorillonite hydrogel composite could be a promising Pb(II) adsorbent.