A four-year size-segregated characterization study of particles PM10, PM2.5 and PM1 depending on air mass origin at Melpitz

PM₁₀ measurements were started in November 1992 at Melpitz site. The mean PM₁₀ concentration in 1993 was 38 μg m^?3 in the summer season (May until October) and about 44 μg m^?3 in the winter season (November until April). The mean PM₁₀ level decreased until 1999 and varies now in ranges from 20–34 μg m^?3 to 17–24 μg m^?3 (minimum and maximum mean values for 1999–2008) in winter and summer seasons, respectively. High volume filter samples of particles PM₁₀, PM_2.5 and PM₁ were characterized for mass, water-soluble ions, organic and elemental carbon from 2004 until 2008. The percentage of PM_2.5 in PM₁₀ varies between summer (71.6%) and winter seasons (81.9%). Mean concentrations of PM₁₀, PM_2.5 and PM₁ in Melpitz were 20, 15, and 13 μg m^?3 in 2004, 22, 18, and 13 μg m^?3 in 2005, 24, 19, and 12 μg m^?3 in 2006 and 22, 17, and 12 μg m^?3 in 2007, respectively. In the four winters the rural background concentration PM₁₀ at Melpitz exceeded the daily 50 μg m^?3 limit for Europe on 8, 8, 7 and 6 days, respectively.Findings for a simple two-sector-classification of the samples (May 2004 until April 2008) using 96-h backward trajectories for the identification of source regions are: Air masses were transported most of time (60%) from the western sector and secondly (17%) from the eastern sector. The lowest daily mean mass concentration PM₁₀ were found during western inflow in summer (17 μg m^?3) containing low amounts of sulphate (2.4 μg m^?3), nitrate (1.7 μg m^?3), ammonium (1.1 μg m^?3) and TC (3.7 μg m^?3). In opposite the highest mean mass concentration PM₁₀ was found during eastern inflow in winter (35 μg m^?3) with high amounts of sulphate (6.1 μg m^?3), nitrate (5.4 μg m^?3), ammonium (3.8 μg m^?3) and TC (9.4 μg m^?3). An estimation of secondary formed OC (SOA) shows 0.8–0.9 μg m^?3 for air masses from West and 2.1–2.2 μg m^?3 from East. The seasonal difference can be neglected.The half-hourly measurements of the particle mass concentration PM₁₀ evaluated as mean daily courses using a TEOM^® show low values (14–21 μg m^?3) in summer and winter for air masses transported from West and the highest concentrations (31–38 μg m^?3) in winter for air masses from East.The results demonstrate the influence of meteorological parameters on long-range transport, secondary particle mass formation and re-emission which modify mass concentration and composition of PM₁₀, PM_2.5 and PM₁. Melpitz site is located in the East of Germany faraway from strong local anthropogenic emissions (rural background). Therefore, this site is suitable for investigation of the influence of long-range transport of air pollution in continental air masses from the East with source regions inside and outside of the European Union.     

Quantifying road dust resuspension in urban environment by Multilinear Engine: A comparison with PMF2

Atmospheric PM pollution from traffic comprises not only direct emissions but also non-exhaust emissions because resuspension of road dust that can produce high human exposure to heavy metals, metalloids, and mineral matter. A key task for establishing mitigation or preventive measures is estimating the contribution of road dust resuspension to the atmospheric PM mixture. Several source apportionment studies, applying receptor modeling at urban background sites, have shown the difficulty in identifying a road dust source separately from other mineral sources or vehicular exhausts. The Multilinear Engine (ME-2) is a computer program that can solve the Positive Matrix Factorization (PMF) problem. ME-2 uses a programming language permitting the solution to be guided toward some possible targets that can be derived from a priori knowledge of sources (chemical profile, ratios, etc.). This feature makes it especially suitable for source apportionment studies where partial knowledge of the sources is available.In the present study ME-2 was applied to data from an urban background site of Barcelona (Spain) to quantify the contribution of road dust resuspension to PM₁₀ and PM_2.5 concentrations. Given that recently the emission profile of local resuspended road dust was obtained (Amato, F., Pandolfi, M., Viana, M., Querol, X., Alastuey, A., Moreno, T., 2009. Spatial and chemical patterns of PM₁₀ in road dust deposited in urban environment. Atmospheric Environment 43 (9), 1650–1659), such a priori information was introduced in the model as auxiliary terms of the object function to be minimized by the implementation of the so-called “pulling equations”.ME-2 permitted to enhance the basic PMF solution (obtained by PMF2) identifying, beside the seven sources of PMF2, the road dust source which accounted for 6.9 μg m^?3 (17%) in PM₁₀, 2.2 μg m^?3 (8%) of PM_2.5 and 0.3 μg m^?3 (2%) of PM₁. This reveals that resuspension was responsible of the 37%, 15% and 3% of total traffic emissions respectively in PM₁₀, PM_2.5 and PM₁. Therefore the overall traffic contribution resulted in 18 μg m^?3 (46%) in PM₁₀, 14 μg m^?3 (51%) in PM_2.5 and 8 μg m^?3 (48%) in PM₁. In PMF2 this mass explained by road dust resuspension was redistributed among the rest of sources, increasing mostly the mineral, secondary nitrate and aged sea salt contributions.     

Physicochemical variations in atmospheric aerosols recorded at sea onboard the Atlantic–Mediterranean 2008 Scholar Ship cruise (Part I): Particle mass concentrations,size ratios,and main chemical components

We report on ambient atmospheric aerosols present at sea during the Atlantic–Mediterranean voyage of Oceanic II (The Scholar Ship) in spring 2008. A record was obtained of hourly PM₁₀, PM_2.5, and PM₁ particle size fraction concentrations and 24-h filter samples for chemical analysis which allowed for comparison between levels of crustal particles, sea spray, total carbon, and secondary inorganic aerosols. On-board monitoring was continuous from the equatorial Atlantic to the Straits of Gibraltar, across the Mediterranean to Istanbul, and back via Lisbon to the English Channel. Initially clean air in the open Atlantic registered PM₁₀ levels <10 μg m^?3 but became progressively polluted by increasingly coarse PM as the ship approached land. Away from major port cities, the main sources of atmospheric contamination identified were dust intrusions from North Africa (NAF), smoke plumes from biomass burning in sub-Saharan Africa and Russia, industrial sulphate clouds and other regional pollution sources transported from Europe, sea spray during rough seas, and plumes emanating from islands. Under dry NAF intrusions PM₁₀ daily mean levels averaged 40–60 μg m^?3 (30–40 μg m^?3 PM_2.5; c. 20 μg m^?3 PM₁), peaking briefly to >120 μg m^?3 (hourly mean) when the ship passed through curtains of higher dust concentrations amassed at the frontal edge of the dust cloud. PM₁/PM₁₀ ratios ranged from very low during desert dust intrusions (0.3–0.4) to very high during anthropogenic pollution plume events (0.8–1).     

Experimental and statistical analyses to characterize in-vehicle fine particulate matter behavior inside public transit buses operating on B20-grade biodiesel fuel

This paper presents results from an in-vehicle air quality study of public transit buses in Toledo, Ohio, involving continuous monitoring, and experimental and statistical analyses to understand in-vehicle particulate matter (PM) behavior inside buses operating on B20-grade biodiesel fuel. The study also focused on evaluating the effects of vehicle’s fuel type, operating periods, operation status, passenger counts, traffic conditions, and the seasonal and meteorological variation on particulates with aerodynamic diameter less than 1 micron (PM_1.0). The study found that the average PM_1.0 mass concentrations in B20-grade biodiesel-fueled bus compartments were approximately 15 μg m^?3, while PM_2.5 and PM₁₀ concentration averages were approximately 19 μg m^?3 and 37 μg m^?3, respectively. It was also observed that average hourly concentration trends of PM_1.0 and PM_2.5 followed a “μ-shaped” pattern during transit hours.Experimental analyses revealed that the in-vehicle PM_1.0 mass concentrations were higher inside diesel-fueled buses (10.0–71.0 μg m^?3 with a mean of 31.8 μg m^?3) as compared to biodiesel buses (3.3–33.5 μg m^?3 with a mean of 15.3 μg m^?3) when the windows were kept open. Vehicle idling conditions and open door status were found to facilitate smaller particle concentrations inside the cabin, while closed door facilitated larger particle concentrations suggesting that smaller particles were originating outside the vehicle and larger particles were formed within the cabin, potentially from passenger activity. The study also found that PM_1.0 mass concentrations at the back of bus compartment (5.7–39.1 μg m^?3 with a mean of 28.3 μg m^?3) were higher than the concentrations in the front (5.7–25.9 μg m^?3 with a mean of 21.9 μg m^?3), and the mass concentrations inside the bus compartment were generally 30–70% lower than the just-outside concentrations. Further, bus route, window position, and time of day were found to affect the in-vehicle PM concentrations significantly. Overall, the in-vehicle PM_1.0 concentrations inside the buses operating on B20-grade biodiesel ranged from 0.7 μg m^?3 to 243 μg m^?3, with a median of 11.6 μg m^?3.Statistical models developed to study the effects of vehicle operation and ambient conditions on in-vehicle PM concentrations suggested that while open door status was the most important influencing variable for finer particles and higher passenger activity resulted in higher coarse particles concentrations inside the vehicle compartments, ambient PM concentrations contributed to all PM fractions inside the bus irrespective of particle size.     

Modelling the formation and atmospheric transport of secondary inorganic aerosols with special attention to regions with high ammonia emissions

Regional simulations of sulfate, nitrate and ammonium aerosols were performed by a nested application of the online-coupled three-dimensional Eulerian model system COSMO-MUSCAT. This was done in a domain covering the northern part of Germany and surrounding regions for the full month of May and a 6-week period in August/September 2006 with the primary focus on secondary inorganic aerosol levels caused by ammonia emissions from domesticated animals and agricultural operations.The results show that in situations with westerly winds ammonium nitrate dominates with concentrations of about 5–10 μg m^?3 whereas the ammonium sulfate concentrations are about 5 μg m^?3. In situations with winds mainly from the East characterized by warmer and dryer air the ammonium sulfate concentrations have their maximum at about 10 μg m^?3 whereas at the same time no ammonium nitrate is present.A reduction of agricultural NH₃ emissions by 50% in a regional scale reduces the ammonium nitrate concentrations to a maximum of 30%, while the ammonium sulfate concentrations are unchanged. The reduction of NH₃ emissions in a more limited area (here in the Federal state of Germany Niedersachsen) does have no noticeable effect neither on ammonium sulfate nor on ammonium nitrate.     

Speciation and diurnal variation of thoracic,fine thoracic and sub-micrometer airborne particulate matter at naturally ventilated office environments

Thoracic (PM₁₀), fine thoracic (PM_2.5) and sub-micrometer (PM₁) airborne particulate matter was sampled during day and night. In total, about 100 indoor and outdoor samples were collected for each fraction at ten different office environments. Energy-dispersive X-ray fluorescence spectrometry and ion chromatography were applied for the quantification of some major and minor elements and ions in the collected aerosols. During daytime, mass concentrations were in the ranges: 11–29, 8.1–24, and 6.6–18 μg m^?3, with averages of 20 ± 1, 15.0 ± 0.9, and 11.0 ± 0.8 μg m^?3, respectively. At night, mass concentrations were found to be significantly lower for all fractions. Indoor PM₁ concentrations exceeded the corresponding outdoor levels during office hours and were thought to be elevated by office printers. Particles with diameters between 1 and 2.5 μm and 2.5 and 10 μm were mainly associated with soil dust elements and were clearly subjected to distinct periods of settling/resuspension. Indoor NO₃^? levels were found to follow specific microclimatic conditions at the office environments, while daytime levels of sub-micrometer Cl^? were possibly elevated by the use of Cl-containing cleaning products. Indoor carbon black concentrations were sometimes as high as 22 μg m^?3 and were strongly correlated with outdoor traffic conditions.     

Indoor particle size distributions in homes with open fires and improved Patsari cook stoves

Particulate pollution has been clearly linked with adverse health impacts from open fire cookstoves, and indoor air concentrations are frequently used as a proxy for exposures in health studies. Implicit are the assumptions that the size distributions for the open fire and improved stove are not significantly different, and that the relationship between indoor concentrations and personal exposures is the same between stoves. To evaluate the impact of these assumptions size distributions of particulate matter in indoor air were measured with the Sioutas cascade impactor in homes using open fires and improved Patsari stoves in a rural Purepecha community in Michoacan, Mexico. On average indoor concentrations of particles less than 0.25 μm were 72% reduced in homes with improved Patsari stoves, reflecting a reduced contribution of this size fraction to PM_2.5 mass concentrations from 68% to 48%. As a result the mass median diameter of indoor PM_2.5 particulate matter was increased by 29% with the Patsari improved stove compared to the open fire (from 0.42 μm to 0.59 μm, respectively). Personal PM_2.5 exposure concentrations for women in homes using open fires were approximately 61% of indoor concentration levels (156 μg m^?3 and 257 μg m^?3 respectively). In contrast personal exposure concentrations were 77% times indoor air concentration levels for women in homes using improved Patsari stoves (78 μg m^?3and 101 μg m^?3 respectively). Thus, if indoor air concentrations are used in health and epidemiologic studies significant bias may result if the shift in size distribution and the change in relationship between indoor air concentrations and personal exposure concentrations are not accounted for between different stove types.     

Year-long continuous personal exposure to PM2.5 recorded by a fast responding portable nephelometer

Personal exposure to particulate matter of aerodynamic diameter under 2.5 μm (PM_2.5) was monitored using a DustTrak nephelometer. The battery-operated unit, worn by an adult individual for a period of approximately one year, logged integrated average PM_2.5 concentrations over 5 min intervals. A detailed time-activity diary was used to record the experimental subject’s movement and the microenvironments visited. Altogether 239 days covering all the months (except April) were available for the analysis. In total, 60 463 acceptable 5-min averages were obtained. The dataset was divided into 7 indoor and 4 outdoor microenvironments. Of the total time, 84% was spent indoors, 10.9% outdoors and 5.1% in transport. The indoor 5-min PM_2.5 average was higher (55.7 μg m^?3) than the outdoor value (49.8 μg m^?3). The highest 5-min PM_2.5 average concentration was detected in restaurant microenvironments (1103 μg m^?3), the second highest 5-min average concentration was recorded in indoor spaces heated by stoves burning solid fuels (420 μg m^?3). The lowest 5-min mean aerosol concentrations were detected outdoors in rural/natural environments (25 μg m^?3) and indoors at the monitored person’s home (36 μg m^?3). Outdoor and indoor concentrations of PM_2.5 measured by the nephelometer at home and during movement in the vicinity of the experimental subject’s home were compared with those of the nearest fixed-site monitor of the national air quality monitoring network. The high correlation coefficient (0.78) between the personal and fixed-site monitor aerosol concentrations suggested that fixed-site monitor data can be used as proxies for personal exposure in residential and some other microenvironments. Collocated measurements with a reference method (β-attenuation) showed a non-linear systematic bias of the light-scattering method, limiting the use of direct concentration readings for exact exposure analysis.     

Particulate matter emissions from on-road vehicles in a freeway tunnel study

Particulate matter, including coarse particles (PM_2.5–10, aerodynamic diameter of particle between 2.5 and 10 μm) and fine particles (PM_2.5, aerodynamic diameter of particle lower than 2.5 μm) and their compositions, including elemental carbon, organic carbon, and 11 water-soluble ionic species, and elements, were measured in a tunnel study. A comparison of the six-hour average of light-duty vehicle (LDV) flow of the two sampling periods showed that the peak hours over the weekend were higher than those on weekdays. However, the flow of heavy-duty vehicles (HDVs) on the weekdays was significant higher than that during the weekend in this study. EC and OC content were 49% for PM_2.5–10 and 47% for PM_2.5 in the tunnel center. EC content was higher than OC content in PM_2.5–10, but EC was about 2.3 times OC for PM_2.5. Sulfate, nitrate, ammonium were the main species for PM_2.5–10 and PM_2.5. The element contents of Na, Al, Ca, Fe and K were over 0.8 μg m^?3 in PM_2.5–10 and PM_2.5. In addition, the concentrations of S, Ba, Pb, and Zn were higher than 0.1 μg m^?3 for PM_2.5–10 and PM_2.5. The emission factors of PM_2.5–10 and PM_2.5 were 18 ± 6.5 and 39 ± 11 mg km^?1-vehicle, respectively. The emission factors of EC/OC were 3.6/2.7 mg km^?1-vehicle for PM_2.5–10 and 15/4.7 mg km^?1-vehicle for PM_2.5 Furthermore, the emission factors of water-soluble ions were 0.028(Mg²⁺)–0.81(SO₄^2?) and 0.027(NO₂^?)–0.97(SO₄^2?) mg km^?1-vehicle for PM_2.5–10 and PM_2.5, respectively. Elemental emission factors were 0.003(V)–1.6(Fe) and 0.001(Cd)–1.05(Na) mg km^?1-vehicle for PM_2.5–10 and PM_2.5, respectively.     

Quantification of Saharan dust contribution to PM10 concentrations over Italy during 2003–2005

Italy is frequently affected by Saharan dust intrusions, which result in high PM₁₀ concentrations in the atmosphere and can cause the exceedances of the PM₁₀ daily limits (50 μg m^?3) set by the European Union (EU/2008/50). The estimate of African dust contribution to PM₁₀ concentrations is therefore a key issue in air quality assessment and policy formulation. This study presents a first identification of Saharan dust outbreaks as well as an estimate of the African dust contribution to PM₁₀ concentrations during the period 2003–2005 over Italy. The identification of dust events has been carried out by looking at different sources of information such as monitoring network observations, satellite images, ground measurements of aerosol optical properties, dust model simulations and air mass backward trajectory analysis. The contribution of Saharan dust to PM₁₀ monthly concentrations has been estimated at seven Italian locations. The results are both spatially (with station) and temporally (with month and year) variable, as a consequence of the variability of the meteorological conditions. However, excluding the contribution of severe dust events (21st February 2004, 25th–28th September 2003, 23rd–27th March 2005), the monthly contribution of dust varies approximately between 1 μg m^?3 and 10 μg m^?3 throughout year 2005 and between 1 μg m^?3 and 8 μg m^?3 throughout year 2003. In 2004 the dust concentration is lower than 2003 and 2005 (<5 μg m^?3 at all sites). The reduction in the number of daily exceedances of the limit value (50 μg m^?3) after subtraction of the dust contribution is also calculated at each station: it varies with station between 20% and 50% in 2005 and between 5% and 25% in 2003 and 2004.     

Meteorological variability in NO2 and PM10 concentrations in the Netherlands and its relation with EU limit values

The extent of the exceedance of the EU limit values for nitrogen dioxide (NO₂) and particulate matter (PM₁₀) concentrations within the Netherlands is expected to decrease significantly, in the coming years. Whether limit values will actually be exceeded, in the next decade, depends not only on European, national and local policies, but also on the effects of inevitable interannual meteorological fluctuations. An analysis of model calculations and measurements yields variations (1 sigma) in the annual average concentration of about 5% for NO₂ and 9% for PM₁₀, due to meteorological fluctuations. These deviations from long-term average concentrations affect assessments of future levels, set against limit values. For instance, an NO₂ concentration of 39 μg m^?3, estimated for a given year with long-term average meteorology, indicates that it is likely (chance >66%) that the limit value of 40 μg m^?3 will not be exceeded in that particular year. At the same time, the estimation also indicates, for example, that this situation is unlikely (change <33%) to continue for three years in a row. However, with an estimated concentration of 38 μg m^?3, it is likely that the limit value will not be exceeded for three years in a row. The limit value for the daily average PM₁₀ concentration is equivalent to an annual average of about 32 μg m^?3. This threshold is unlikely to be exceeded for three years in a row, when an annual average concentration of 29 μg m^?3 is estimated. Interannual variations in concentrations of NO₂ and PM₁₀ are linked to large-scale meteorological fluctuations. Therefore, similar results can be expected for other European countries.     

Experimental evidence for a significant contribution of cellulose to indoor aerosol mass concentration

An apartment bedroom located in a residential area of Aveiro (Portugal) was selected with the aim of characterizing the cellulose content of indoor aerosol particles. Two sets of samples were taken: (1) PM₁₀ collected simultaneously in indoor and outdoor air; (2) PM₁₀ and PM_2.5 collected simultaneously in indoor air. The aerosol particles were concentrated on quartz fibre filters with low-volume samplers equipped with size selective inlets. The filters were weighed and then extracted for cellulose analysis by an enzymatic method. The average indoor cellulose concentration was 1.01 ± 0.24 μg m^?3, whereas the average outdoor cellulose concentration was 0.078 ± 0.047 μg m^?3, accounting for 4.0% and 0.4%, respectively, of the PM₁₀ mass. The corresponding average ratio between indoor and outdoor cellulose concentrations was 11.1 ± 4.9, indicating that cellulose particles were generated indoors, most likely due to the handling of cotton-made textiles as a result of routine daily activities in the bedroom. Indoor cellulose concentrations averaged 1.22 ± 0.53 μg m^?3 in the aerosol coarse fraction (determined from the difference between PM₁₀ and PM_2.5 concentrations) and averaged 0.38 ± 0.13 μg m^?3 in the aerosol fine fraction. The average ratio between the coarse and fine fractions of cellulose concentrations in the indoor air was 3.6 ± 2.1. This ratio is in line with the primary origin of this biopolymer. Results from this study provide the first experimental evidence in support of a significant contribution of cellulose to the mass of suspended particles in indoor air.     

PM2.5, soot and NO2 indoor–outdoor relationships at homes,pre-schools and schools in Stockholm,Sweden

In developed nations people spend about 90% of their time indoors. The relationship between indoor and outdoor air pollution levels is important for the understanding of the health effects of outdoor air pollution. Although other studies describe both the outdoor and indoor atmospheric environment, few excluded a priori major indoor sources, measured the air exchange rate, included more than one micro-environment and included the presence of human activity. PM_2.5, soot, NO₂ and the air exchange rate were measured during winter and summer indoors and outdoors at 18 homes (mostly apartments) of 18 children (6–11-years-old) and also at the six schools and 10 pre-schools that the children attended. The three types of indoor environments were free of environmental tobacco smoke and gas appliances, as the aim was to asses to what extent PM_2.5, soot and NO₂ infiltrate from outdoors to indoors. The median indoor and outdoor PM_2.5 levels were 8.4 μg m^?3 and 9.3 μg m^?3, respectively. The median indoor levels for soot and NO₂ were 0.66 m^?1 × 10^?5 and 10.0 μg m^?3, respectively. The respective outdoor levels were 0.96 m^?1 × 10^?5 and 12.4 μg m^?3. The median indoor/outdoor (I/O) ratios were 0.93, 0.76 and 0.92 for PM_2.5, soot and NO₂, respectively. Their infiltration factors were influenced by the micro-environment, ventilation type and air exchange rate, with aggregated values of 0.25, 0.55 and 0.64, respectively. Indoor and outdoor NO₂ levels were strongly associated (R² = 0.71), followed by soot (R² = 0.50) and PM_2.5 (R² = 0.16). In Stockholm, the three major indoor environments occupied by children offer little protection against combustion-related particles and gases in the outdoor air. Outdoor PM_2.5 seems to infiltrate less, but indoor sources compensate.     

Aerosol transport model evaluation of an extreme smoke episode in Southeast Asia

Biomass burning is one of many sources of particulate pollution in Southeast Asia, but its irregular spatial and temporal patterns mean that large episodes can cause acute air quality problems in urban areas. Fires in Sumatra and Borneo during September and October 2006 contributed to 24-h mean PM₁₀ concentrations above 150 μg m^?3 at multiple locations in Singapore and Malaysia over several days. We use the FLAMBE model of biomass burning emissions and the NAAPS model of aerosol transport and evolution to simulate these events, and compare our simulation results to 24-h average PM₁₀ measurements from 54 stations in Singapore and Malaysia. The model simulation, including the FLAMBE smoke source as well as dust, sulfate, and sea salt aerosol species, was able to explain 50% or more of the variance in 24-h PM₁₀ observations at 29 of 54 sites. Simulation results indicated that biomass burning smoke contributed to nearly all of the extreme PM₁₀ observations during September–November 2006, but the exact contribution of smoke was unclear because the model severely underestimated total smoke emissions. Using regression analysis at each site, the bias in the smoke aerosol flux was determined to be a factor of between 2.5 and 10, and an overall factor of 3.5 was estimated. After application of this factor, the simulated smoke aerosol concentration averaged 20% of observed PM₁₀, and 40% of PM₁₀ for days with 24-h average concentrations above 150 μg m^?3. These results suggest that aerosol transport models can aid analysis of severe pollution events in Southeast Asia, but that improvements are needed in models of biomass burning smoke emissions.     

Impact of smoking on in-vehicle fine particle exposure during driving

Indoor smoking ban in public places can reduce secondhand smoke (SHS) exposure. However, smoking in cars and homes has continued. The purpose of this study was to assess particulate matter less than 2.5 μm (PM_2.5) concentration in moving cars with different window opening conditions. The PM_2.5 level was measured by an aerosol spectrometer inside and outside moving cars simultaneously, along with ultrafine particle (UFP) number concentration, speed, temperature and humidity inside cars. Two sport utility vehicles were used. Three different ventilation conditions were evaluated by up to 20 repeated experiments. In the pre-smoking phase, average in-vehicle PM_2.5 concentrations were 16–17 μg m^?3. Regardless of different window opening conditions, the PM_2.5 levels promptly increased when smoking occurred and decreased after cigarette was extinguished. Although only a single cigarette was smoked, the average PM_2.5 levels were 506–1307 μg m^?3 with different window opening conditions. When smoking was ceased, the average PM_2.5 levels for 15 min were several times higher than the US National Ambient Air Quality Standard of 35 μg m^?3. It took longer than 10 min to reach the level of the pre-smoking phase. Although UFP levels had a similar temporal profile of PM_2.5, the increased levels during the smoking phase were relatively small. This study demonstrated that the SHS exposure in cars with just a single cigarette being smoked could exceed the US EPA NAAQS under realistic window opening conditions. Therefore, the findings support the need for public education against smoking in cars and advocacy for a smoke-free car policy.     

Fine particles and carbon monoxide from wood burning in 17th–19th century Danish kitchens: Measurements at two reconstructed farm houses at the Lejre Historical–Archaeological Experimental Center

Carbon monoxide (CO) and particulate matter (PM_2.5) were measured in two reconstructed Danish farmhouses (17–19th century) during two weeks of summer. During the first week intensive measurements were performed while test cooking fires were burned, during the second week the houses were monitored while occupied by guest families. A masonry hearth was located in the middle of each house for open cooking fires and with heating stoves. One house had a chimney leading to the outside over the hearth; in the other, a brickwork hood led the smoke into an attic and through holes in the roof. During the first week the concentration of PM_2.5 averaged daily between 138 and 1650 μg m^?3 inside the hearths and 21–160 μg m^?3 in adjacent living rooms. CO averaged daily between 0.21 and 1.9 ppm in living areas, and up to 12 ppm in the hearths. Highest concentrations were measured when two fires were lit at the same time, which would cause high personal exposure for someone working in the kitchens. 15 min averages of up to 25 400 μg m^?3 (PM_2.5) and 260 ppm CO were recorded. WHO air quality guidelines were occasionally exceeded for CO and constantly for PM_2.5. However, air exchange and air distribution measurements revealed a large draw in the chimney, which ensured a fast removal of wood smoke from the hearth area. The guest families were in average exposed to no more than 0.21 ppm CO during 48 h. Based on a hypothetical time-activity pattern, however, a woman living in this type of house during the 17–19th century would be exposed to daily averages of 1.1 ppm CO and 196 μg m^?3 PM_2.5, which exceeds WHO guideline for PM_2.5, and is comparable to what is today observed for women in rural areas of developing countries.     

Discriminating the regional and urban contributions in the North-Western Mediterranean: PM levels and composition

Simultaneous measurements of the PM concentration levels and chemical composition of atmospheric aerosols at a regional background (RB) and an urban background (UB) site, located in the same geographic region, allowed for the determination of their urban and regional contributions. In the specific case of the North-Western region of the Mediterranean the RB amount has been quantified in 18, 13 and 12 μg m^?3 for PM₁₀, PM_2.5 and PM₁, respectively, whereas the UB contribution reached 22, 13 and 8 μg m^?3, respectively. The UB contributions in the Western Mediterranean are much higher than those observed in other European regions; especially concerning the coarse fraction. The high loads of road dust in the urban areas across the Mediterranean may account for these large differences.The urban contributions are extremely enriched in Ca, Fe, Sb, Sn, Cu, Zn, being the main tracers of the road dust, with concentrations up to 6–8 times higher than those at the RB. Elemental carbon and nitrate are mainly derived from direct vehicular emissions. Some industrial tracers (Mn, Pb, Bi) are also enriched in the urban area. The evaluation of the Cu/Sb, Cu/Zn, Cu/Cd and Cu/Pb ratios and the high enrichment of these trace elements versus the Upper Crustal Composition average values corroborates the importance of the road-traffic emissions in the study area, also influencing the RB.The supplementary results from a suburban site in the Balearic Islands and the evaluation of the V/Ni ratios evidence the strong signature of fuel-oil combustion processes, which is a general characteristic of the Mediterranean aerosols.     

Temporal characteristics from continuous measurements of PM2.5 and speciation at the Taipei Aerosol Supersite from 2002 to 2008

This study uses monitoring data collected at the Taipei Aerosol Supersite from March 2002 to February 2008 to analyze characteristics such as seasonal fluctuations, diurnal variations, and photochemical-related variations of PM_2.5 chemical compositions. The results indicate that the average of PM_2.5 mass concentration in Taipei during this period is 30.3 ± 16.0 μg m^?3. The highest average concentration of PM_2.5 components is that of sulfate, which accounts for 21.1% of the PM_2.5 mass, followed by organic carbon (OC) at 15.9%, nitrate at 5.8%, and elemental carbon (EC) at 5.4%. Concentrations of EC, OC, and nitrate have distinctive but similar seasonal fluctuations, which is highest in spring and lowest in fall. Sulfate concentration has less seasonal fluctuations, and the highest value appears during the fall. Similarly, concentrations of EC, OC, and nitrate have notable diurnal variations; however, the diurnal variation of sulfate concentration is not very apparent. These observation data show that EC, OC, and nitrate in PM_2.5 in the Taipei metropolis come mainly from local emissions, while sulfate comes mainly from the regional transport of pollutants. This is likely because Taiwan is located on the lee zone of the Asian prevailing winds from fall to spring; its air quality is frequently affected by the transport of air pollutants from Mainland China. In addition, the extent of increase in aerosols is much higher than that of CO, indicating the formation of secondary aerosol when photochemical activity is strong. Based on six years of observation data, this study explores three potential scenarios to set up Taiwan's PM_2.5 air quality standard (AQS). The analysis indicates that the optimum standard for 24-h air quality of PM_2.5 should be around 50 μg m^?3.     

Chemical characterization and source apportionment of fine and coarse particulate matter in Lahore,Pakistan

Lahore, Pakistan is an emerging megacity that is heavily polluted with high levels of particle air pollution. In this study, respirable particulate matter (PM_2.5 and PM₁₀) were collected every sixth day in Lahore from 12 January 2007 to 19 January 2008. Ambient aerosol was characterized using well-established chemical methods for mass, organic carbon (OC), elemental carbon (EC), ionic species (sulfate, nitrate, chloride, ammonium, sodium, calcium, and potassium), and organic species. The annual average concentration (±one standard deviation) of PM_2.5 was 194 ± 94 μg m^?3 and PM₁₀ was 336 ± 135 μg m^?3. Coarse aerosol (PM_10?2.5) was dominated by crustal sources like dust (74 ± 16%, annual average ± one standard deviation), whereas fine particles were dominated by carbonaceous aerosol (organic matter and elemental carbon, 61 ± 17%). Organic tracer species were used to identify sources of PM_2.5 OC and chemical mass balance (CMB) modeling was used to estimate relative source contributions. On an annual basis, non-catalyzed motor vehicles accounted for more than half of primary OC (53 ± 19%). Lesser sources included biomass burning (10 ± 5%) and the combined source of diesel engines and residual fuel oil combustion (6 ± 2%). Secondary organic aerosol (SOA) was an important contributor to ambient OC, particularly during the winter when secondary processing of aerosol species during fog episodes was expected. Coal combustion alone contributed a small percentage of organic aerosol (1.9 ± 0.3%), but showed strong linear correlation with unidentified sources of OC that contributed more significantly (27 ± 16%). Brick kilns, where coal and other low quality fuels are burned together, are suggested as the most probable origins of unapportioned OC. The chemical profiling of emissions from brick kilns and other sources unique to Lahore would contribute to a better understanding of OC sources in this megacity.     

Determinants of exposure to fine particulate matter (PM2.5) for waiting passengers at bus stops

This research evaluates commuter exposure to particulate matter during pre-journey commute segments for passengers waiting at bus stops by investigating 840 min of simultaneous exposure levels, both inside and outside seven bus shelters in Buffalo, New York. A multivariate regression model is used to estimate the relation between exposure to particulate matter (PM_2.5 measured in μg m^?3) and three vectors of determinants: time and location, physical setting and placement, and environmental factors. Four determinants have a statistically significant effect on particulate matter: time of day, passengers’ waiting location, land use near the bus shelter, and the presence of cigarette smoking at the bus shelter. Model results suggest that exposure to PM_2.5 inside a bus shelter is 2.63 μg m^?3 (or 18 percent) higher than exposure outside a bus shelter, perhaps due in part to the presence of cigarette smoking. Morning exposure levels are 6.51 μg m^?3 (or 52 percent) higher than afternoon levels. Placement of bus stops can affect exposure to particulate matter for those waiting inside and outside of shelters: air samples at bus shelters located in building canyons have higher particulate matter than bus shelters located near open space.