多孔沸石混合填料BAF废水脱氮及微生物研究

以天然沸石为主要原料,制备改性多孔沸石混合填料,填料柱挂膜成熟后,模拟氨氮废水及曝气生物滤池技术,经离子交换吸附、微生物再生、淋洗序批三段式运行,以考察填料的氮素去除性能,同时采用PCR-DGGE（变性梯度凝胶电泳）电泳方法表征填料生物膜的微生物特性。实验结果表明：当离子交换吸附阶段水力停留时间为3.0 h时,填料的氨氮综合去除效率最佳（82.3%～94.7%）,氮回收率较高（88.46%）;填料系统外层及上、下层的微生物群落丰富度相对更高,不同条带聚类结果与条带相似度及现实状况相符;在条带检测出可降解有机污染物的噬氢菌及硝化菌、反硝化菌。     

不同曝气方式对地下水中铁锰去除效果的研究

通过建立“曝气 一级过滤”的地下水除铁除锰工艺,分别对比了中强度跌水曝气、高强度曝气架曝气两种不同曝气方式的除铁除锰效果及滤料的极限滤速。     

填料式浮选柱操作参数的研究

在实验室装置上研究了不锈钢波纹板填料柱的主要操作参数对除油率的影响。研究结果表明：填料可以明显改善气体在柱内的径向分布，可以明显提高浮选柱的操作稳定性。实验确定了波纹板填料式浮选柱的主要操作参数是：最低气体表现线速度3．8cm／s，污水停留时间为5min，浮选剂投加量为5～10mg／L。     

生物滴滤法净化VOCs及恶臭污染物的研究进展

生物滴滤法处理废气中的VOCs及恶臭污染物具有去除效率高、二次污染小、安全性高等优点。总结了生物滴滤反应器的类型和废气中污染物去除效率的影响因素及强化措施,包括工艺参数与填料的选择、传质限制与添加表面活性剂、微生物的影响与筛选高效降解菌株、真菌的使用、剩余污泥堵塞问题和生物滴滤前的预处理。最后提出生物滴滤法去除废气的发展趋势。     

微生物烟气脱硫技术研究进展

通过对微生物烟气脱硫方法的介绍，综述了微生物烟气脱硫原理、工艺和技术。叙述了烟气吸收和吸收尾液的处理工艺所利用的脱硫微生物种类，并阐述了氧化亚轶硫杆菌、硫酸盐还原茵、丝状硫细菌、光合硫细菌、无色硫细菌和脱氮硫杆菌的代谢途径、作用效果和关键影响因素，并且指出其优缺点。文章总结了国内外在微生物烟气脱硫工艺的研究进展，并对我国今后微生物烟气脱硫技术发展趋势进行了简要分析。     

高脂肪样品中PCBs和OCPs分离方法研究

研究开发了用于分离高脂肪样品中21种多氯联苯（PCBs）和22种有机氯农药（OCPs）的分离柱填料,以及利用该填料分离含脂肪的动物组织样品中PCBs或OCPs的方法。该填料按质量百分比由硅胶-弗罗里硅土混合物30%-35%、酸性改性硅胶50%-60%和无水硫酸钠10%-15%组成,并使用自主研发的四通道色谱分离仪对样品进行分离和净化。利用本方法的填料分离PCBs或OCPs,分离方法高效、快速、工艺简单,可在成本较低的条件下达到显著的分离效果。PCBs化合物柱回收率可达96.4%-119%,对鱼脂肪组织加标回收率可达74.4%-100%;OCPs化合物柱回收率可达78.4%-103%,对鱼脂肪组织加标回收率可达78.3%-102%。结果表明该填料可用于分离PCBs或OCPs,色谱分离效果良好,可以满足高脂肪样品中OCPs和PCBs的监测分离需要。     

高效生物滴滤塔处理化工污水含H2S恶臭气体实验研究

以化工污水水解酸化池收集的现场恶臭气体作为实验气体,以陶粒、半软性塑料作为生物滴滤塔的填料,探讨了生物滴滤塔挂膜过程阻力变化和H2S气体脱除率关系,并以生活污水为营养液进行了连续实验.实验研究表明：在所选实验条件下,为使H2S出口浓度达到0.06mg/m^3,生活污水COD应维持250mg/L以下,SO4^2-浓度＜1400mg/L.     

油田采出水膜法处理技术应用研究进展

对采出水膜法处理技术中的微滤、超滤、纳滤、反渗透膜以及集成技术的应用进行研究,分析成本,总结各技术的特点。超滤、微滤主要处理的是水中的油类以及悬浮物和细菌,纳滤对二价离子的脱除率较高,反渗透技术可以有效降低采出水矿化度。在实际采出水处理中,可综合运用膜技术和生物法达到更好的处理效果。     

石油污染土壤原位生物修复的强化实验研究

为研究添加营养物质和高效降解石油微生物对油污土壤生物修复的作用,通过分层土柱的方法,连续监测了不同条件下不同土层的含水率、石油烃含量、细菌数量及脱氢酶活性。结果表明:添加营养物质同时接种高效微生物可使降解效果明显改善,降解率比在自然条件下提高近50%,而单纯添加营养物质不接种高效微生物可使降解率比在自然条件下提高约25%。降解初期,上层土壤降解效果较好,而到中后期,中下层降解效果好于上层。微生物数量和脱氢酶活性与石油降解率之间存在良好的相关性,脱氢酶活性比微生物数量更能反映修复过程中微生物的存活状态。添加营养物质和高效降解石油微生物对油污土壤原位生物修复具有强化作用。     

从含油污泥中回收油技术的研究

研究从某炼厂含油污泥中回收油的问题，分析结果表明：此种油污泥含油率46.7％、含水率51.2％、含砂率1.7％。实验中分别研究了离心法、热滤法的回收油效果。最终以热滤法实现了油回收率95％、脱水率99%。确定了以热滤法作为该含油污泥回收油的方法。     

沙质滩涂中可溶性油的释放动力学研究

沙质滩涂对石油类污染物的吸附是一种物理吸附过程，在一定的条件下，吸附于沙质滩涂中的石油类污染物又可能释放出来，对滨海环境造成新的污染。在对滨海沙滩（胶州湾）沙质滩涂-水系统石油污染调查的基础上，选择代表性的沙滩进行取样，系统测定不同沙质滩涂对可溶性油的释放动力学过程，并分析了盐度、pH、温度和含沙量对释放作用的影响。结果表明，沙质滩涂对可溶性油的释放动力学曲线符合对数型，即随着时间的延续释放速度逐渐降低，沙质滩涂对可溶性油的释放平衡时间约为10h，沙质滩涂对可溶性油的释放量随盐度和pH的增大而减少，随温度、含沙量和振荡频率的增加而增加。     

滤料级配过滤含聚污水数值模拟研究

以磁铁矿滤料与石英砂滤料为填设滤料层的级配模式一直广泛应用于油田含聚污水处理过程中,但这种滤料级配与污水过滤性能之间的影响关系及规律认识却较为缺乏,本文以悬浮粒子吸附与截留形成的聚集特征为切入,定量分析出水水质特性,对含聚污水过滤过程中滤料级配的影响效果展开数值模拟研究。研究认为：磁铁矿滤料层厚度较大的级配模式过滤具有更好的悬浮粒子吸附与截留效果,对更小粒径悬浮粒子过滤能力更优,但滤料填充高度比与过滤效果存在一定适配性;以1.28以上磁铁矿滤料厚度较大的级配模式过滤较低含聚浓度污水、以1.67以上磁铁矿滤料厚度较小的级配模式过滤较高含聚浓度污水,均可以使出水悬浮固体颗粒与油滴含量均低于5mg/L,满足过滤出水水质指标要求。     

Barley, a potential species for initial reclamation of saline composite tailings of oil sands

The oil sands industry in Alberta (Canada) has developed the composite tailings (CT) process to reduce the fluid fine tails resulting from the processing of oil sands. This process uses a chemical coagulant (gypsum or alum) to produce aggregated fines (clay), so they are retained with the coarse sand fraction of the extraction tailings to form CT, from which fines-free water is released relatively quickly compared with untreated tailings. The resulting CT and CT waters are saline-sodic, with Na+, SO4(2-), and Cl- being the dominant ions. When freshly deposited, the CT deposits are too soft for access by reclamation equipment, and the time required for these deposits to remove the water sufficiently to support traffic is uncertain. A greenhouse study was designed to determine the suitability of barley (Hordeum vulgare L.) for reclamation of fresh CT deposits and to evaluate benefits of peat amendments. This study assessed germination, early plant growth, chlorophyll content, and survival of barley growing in alum- and gypsum-treated CT, with and without peat amendment. Ion and trace metal accumulation in the root and shoot tissues of barley was determined. Amendment of CT with peat improved germination, survival, and growth of barley, but did not prevent leaf injury (probably due to Na and Cl- and possibly multiple nutrient deficiency). Field studies will be undertaken to validate our greenhouse results suggesting that barley could be used to improve dewatering of the freshly deposited substrates, reduce soil erosion, and facilitate leaching of ions by root penetration into the substrate.     

基于LMDI的我国能源消费因素分解研究

经济飞速发展使我国能源消费急剧增长，能源消费与能源供给、环境污染矛盾日益突出。在分析我国能源消费和能源消费强度变化趋势的基础上，运用LMDI法将我国1996--2010年能源消费变化分解为产出效应、结构效应和强度效应，探讨产出提高、结构调整、效率提高对我国能源消费和能源强度的影响。结果显示，生产规模扩大对能源消费起到正向的拉动作用，结构调整对缓解能源消费增长还有较大的上升空间，能源强度对能源消费的抑制效应自“十一五”期间起作用逐步显现。     

Moisture transfer modeling during solar drying of potato cylinders considering shrinkage

In the present work, the thin layer drying kinetics of potato during natural convection solar drying was investigated experimentally. Cylindrical potato samples with length 50 mm and varying diameter of 8, 10 and 13 mm were dried in an in-house designed and fabricated laboratory scale mixed-mode solar dryer. Thirteen different thin-layer mathematical models were fitted to the experimental moisture ratio (MR) data. The obtained results indicated that the Modified Page model could satisfactorily describe the drying curve of potato cylinders with higher value of R² and lower values of RMSE and χ². The shrinkage parameter is incorporated in the analytical diffusion model to study the moisture transfer mechanism of potato cylinders. It was observed that the values of effective diffusion coefficient (D_eff) and convective mass transfer coefficient (h_m) are overestimated in the range of 85.02–90.27% and 39.11–45.11% for the range of sample diameter examined, without considering the shrinkage effect in the mass transfer analysis. A Multiphysics approach was adopted in this study to get insight into the drying behavior of potato cylinders in terms of food-moisture interactions during the solar drying process. The predicted results of MR are in close agreement with the experimental data. Moreover, the anisotropic behavior of shrinkage as well as the moisture distribution inside the potato cylinder was very well described by Multiphysics model.     

Environmental impacts of shore-parallel breakwaters along Nagahama and Ohgata, District of Joetsu, Japan

A combination of sedimentological analysis of beach sands, field surveys and the assessment of the empirical methods for the breakwater design is used to investigate the impacts of offshore breakwaters on beach morphology along Nagahama and Ohgata. The results indicate that the nearshore sedimentation has been substantially disrupted due to the features formed behind the breakwaters stopping littoral transport, which led to sediment accretion on the updrift side of the breakwaters, and erosion on their downdrift side. Sedimentological analysis of beach sands made it possible to recognize the dominant process at the sections considered. In fact, the occurrence of strong offshore-going currents, the removal of finer mean grain size and the predominance of high-density heavy minerals led us to deduce that the two sections undergo a natural sedimentary imbalance.     

Thermodynamic-dynamic analysis of gamma type free-piston stirling engine charged with hydrogen gas as working fluid

ABSTRACT

In this study, the combined thermodynamic and dynamic model of a new concept of gamma type free-piston Stirling engine is conducted. The engine consists of two identical displacer cylinders, a power cylinder, a linear alternator, and three-cushion pistons. Two displacer cylinders are symmetrically positioned on each side of the power cylinder for minimizing the rotational vibrations. Hydrogen is used as the working gas and the effect of gas temperature on the specific heat capacity is considered. The analysis carried out in this study involves the prediction of the thermodynamic-dynamic performance characteristics of the engine. In the thermodynamic section of the analysis, the working space of the engine is divided into 31 nodal volumes and the gas pressures in nodal volumes are assumed to be equal to each other. The conservation of mass and energy equations is obtained for each nodal volume. Instantaneous gas temperatures of nodal volumes are calculated by the first law of thermodynamics given for the unsteady open systems. The dynamic section of the analysis involves the motion equations of displacer, power and cushion pistons. The motion equations are derived using the Newton method. In the calculations done for variable specific heat capacity, it has been determined that there is 1% cyclic work reduction compared to the constant heat capacity. It is estimated that the maximum effective power that can be produced by the linear alternator will be around 1.6 kW. The working frequency range of the proposed engine is found to be suitable to generate electrical power.     

生物滤池强化方法对水源水中乐果去除效果的试验研究

以乐果微污染水源水为研究对象,对比研究了KMnO4与O3作为预氧化剂,石英砂、沸石与活性炭作为滤料的生物滤池对饮用水水源中乐果残留物的去除效果。实验结果表明,以石英砂、沸石和活性炭作为滤料,经高锰酸钾或臭氧预氧化处理后,乐果去除率较好,特别是沸石和活性炭的去除率达到了90%以上。臭氧处理效果比高锰酸钾好,处理率提高了10%以内。从去除率、经济性和易操作性方面考虑,高锰酸钾和沸石联用更适合中国农村供水的实际情况。     

预膜过滤技术在采油污水处理中的应用

详细介绍了新开发的FDF300型过滤工艺,并通过试验验证了自行研制的新型GM助剂在FDF型过滤器中应用的工艺条件,考察了助剂用量、型号、预膜时间以及空气反吹脱渣时间、反吹压力等因素对过滤效果的影响。结果表明,选用150gGM3助剂,预膜时间约20 min,空气反吹脱渣时间5 min,反吹压力0.35 MPa等工艺条件,可以获得理想的过滤效果,解决了长期困扰油田采油污水含油量和机械杂质不达标的难题。     

炉渣用于深层过滤的试验研究

将炉渣用作深层过滤的床层过滤,在油田水处理中具有良好的应用前景。通过对炉渣滤料的物性测定,对流体力学性能、过滤性能及反洗性能的研究,获得了有关炉渣滤料的粒径分布、床层孔隙率、密度、吸水率等物性参数,以及清洁滤料床层阻力与速度的关系曲线和流化曲线,过滤条件下床层阻力随时间的变化关系和悬浮物脱除率随时间的变化曲线,炉渣床层的反洗曲线。结果表明：炉渣表面粗糙,有棱角,吸附表面积大,孔隙率大,过滤效果好;炉渣滤料密度小,反洗效果较好,反洗用水量只是过滤水量的５％左右;同时,炉渣作为滤料用于深层过滤,不仅来源广泛,而且属废物利用。