共查询到19条相似文献,搜索用时 125 毫秒
1.
此文介绍了铝型材挤压模CAD/CAM系统的构造方法和总体结构,以及其中关键问题的解决方法。作者开发的铝型材挤压模CAD/CAM系统(HECAD)可进行平面模和分流模的设计,能输出模具设计工程图纸及模孔线切割加工指令。 相似文献
2.
3.
4.
5.
本文论述了在微机系统(IBM PC/XT)上辅助设计反挤压工艺与模具的方法。研制出了杯形零件反挤压工艺及模具设计的交互式CAD系统。文中提出了挤压件描述公式、形状分类、工艺设计的计算方法和基本设计原则,并对组合凹模的结构优化设计进行了阐述。同时还对交互式绘图软件包(Auto CAD)与高级语言程序的连接、数据交换等关键技术作了论述。利用人机对话输入零件信息,就可得到挤压力、变形程度、坯料重量和尺寸、制坯方法、凸凹模结构等参数,并绘制出了模具工作部分的装配图和零件图。 相似文献
6.
7.
8.
9.
根据铝型材挤压模具的服役条件,采用宏观与微观相结合的分析方法,分析现场挤压模具的失效形式、失效性质和失效原因,并提出了提高模具使用寿命的一些措施. 相似文献
10.
CAD技术已逐渐从二维系统向三维实体造型方面转变.以Solidworks作为支撑平台,以Visual Basic和Access为开发工具,应用面向对象的程序开发方法,开发了一个挤压模CAD系统.对该系统的设计做了概括性的描述,并介绍了该系统的软件开发过程中的关键技术. 相似文献
11.
12.
等温超塑挤压成形技术开辟了铜合金实体保持架加工的新途径。在此新技术的基础上,利用VC++6.0和ObjectARX开发了一套铜合金轴承实体保持架挤压模CAD系统软件,大幅度缩短了保持器系列产品的开发周期,并提高了产品设计效率和设计水平。 相似文献
13.
14.
此文介绍了非轴对称腰鼓形零件——水阀手柄闭式反向挤压模具的水平可分凹模结构设计及成刑试验工艺过程,为类似零件的锻压成形提供了成功的实例。 相似文献
15.
用增量网格法对带内孔坯复合挤压的载荷、上下通道流出量、金属内部应力应变分布情况进行实验分析,并分析内孔直径和凹模锥角等参数的影响,对设计模具与选择成形设备有指导意义.文中还阐述这种实验方法的实施过程和功能,指出这是一种研究成形问题的有效手段. 相似文献
16.
17.
在分析冲模结构设计特点的基础上,介绍了在UG装配环境下所开发的冲模三维CAD系统的设计流程和实现方法,并对系统的主要功能模块和关键技术做了概括性介绍。 相似文献
18.
19.
H.-J. Hu 《Journal of Manufacturing Processes》2012,14(3):181-187
It is important to research the effect of die structures parameters for equal channel angular extrusion (ECAE) on the deformation behavior, strain distribution and loads requirement. ECAE is an extrusion process widely researched for its potential to produce ultra-fine grained microstructures in magnesium alloys. In this paper some three-dimensional (3D) geometric models with different corner angles 90° and 135° and with fillets or not in the bottom die were designed by UG software. Some important isothermal process parameters were regarded as basal conditions used in DEFORM?-3D software such as temperatures, the friction coefficient, and extrusion speed. The deformation heterogeneity of ECAE was analyzed from the simulation and experimental results. The deformation homogeneity caused by the EACE die with fillets was improved comparing with the die without fillets. But the cumulative maximum strains decreased. The requirement extrusion force decreased with the fillets and channel angle increase in ECAE die. From the simulation and experimental results the smaller channel angle can obtain the higher cumulative strains and produce tinier subgrains. The loads of top die decrease mainly with fillets. The ECAE die with the channel angle 90° and fillets is good to improve the plasticity and deformation homogeneity of the billets if the extrusion force is enough. It was demonstrated that the simulation results were in good agreement with experimental results and the theoretical calculation. 相似文献