Experimental Investigation of Cellulose/Silver Nanocomposites Using In Situ Generation Method

Cellulose gel films were prepared by regeneration process using pre-cooled aq.(8 wt% LiOH + 15 wt% urea) mixture as solvent and ethyl alcohol as non solvent. The Terminus cattapa leaf extract diffused wet cellulose films were then dipped in 1–5 mM aq.AgNO₃ solutions to allow in situ generation of silver nanoparticles (AgNPs). Besides the in situ generation, some AgNPs were also formed outside the wet films in the solution. The AgNPs formed outside the films were observed under transmission electron microscope and scanning electron microscope. The nanocomposite films were also characterized by Fourier transform infrared spectroscopy, X-ray diffraction and thermogravimetric analysis and tensile test. The thermal stability of the composite films was lower than that of the matrix up to a temperature of ~300 °C and afterwards showed a reverse trend. The tensile strength of the nanocomposite films was found to be higher than the matrix but decreased with increasing concentration of aq.AgNO₃. The cellulose/AgNPs composite films showed good antibacterial activity against E. coli (gram positive) and Bacillus sp. (gram negative). Based on the aforementioned properties, the cellulose/AgNPs composite films can be considered for antibacterial packaging and medical applications.     

Environmentally-Friendly Synthesis of Ag Nanoparticles by Fusarium sporotrichioides for the Production of PVA/Bentonite/Ag Composite Nanofibers

Membranes and filters made of nanofibers can have many medicines and water treatment applications. The use of silver nanoparticles (AgNPs) with antibacterial activity in these structures improve their efficiency. However, due to the toxicity of the compounds used in the chemical synthesis of AgNPs, in this study, AgNPs were obtained through a biological process using Fusarium sporotrichioides. AgNPs preparation conditions were optimized, including F. sporotrichioides medium and AgNO₃ concentration. Next, a PVA nanofiber membrane with bentonite and AgNPs (Bio-AgNPs or Chem-AgNPs) was prepared using electrospinning. The optimal conditions for the production of Bio-AgNPs were the culture of F. sporotrichioides in the MGYP culture medium and 12 M of AgNO₃. The Bio-AgNPs particle size and zeta potential were 58 nm and ??16.8 mV, respectively, with antibacterial activity. The PVA/NB/AgNPs nanofibers operation conditions included 7.5% w/w PVA, 3% w/w bentonite, and AgNPs 5% w/w at a voltage of 11 kV, feed rate of 0.5 mL/h, and 15 cm distance between the needle and the collector. The average diameter of the PVA/NB/Bio-AgNPs nanofibers was 230 nm. Also, the presence of silver in the nanofibers was confirmed through EDX and XRD methods. The antibacterial assay of the nanofibers showed that the inhibition zone of PVA/NB/Bio-AgNPs against E. coli and S. aureus was 0.62 and 0.36 mm, which is better than PVA/NB/Chem-AgNPs and comparable with chloramphenicol. The produced membrane is suitable for water treatment, food packaging, and wound dressing because of its good thermal, mechanical, and antibacterial properties.

     

Chitosan/Hydrophilic Plasticizer-Based Films: Preparation,Physicochemical and Antimicrobial Properties

The addition of plasticizers to biopolymer films is a good method for improving their physicochemical properties. The aim of this study was to evaluate the effect of chitosan (CHI) blended with two hydrophilic plasticizers glycerol (GLY) and sorbitol (SOR), at two concentrations (20 and 40 wt%) on their mechanical, thermal, barrier, structural, morphological and antimicrobial properties. The chitosan was prepared through the alkaline deacetylation of chitin obtained from fermented lactic from shrimp heads. The obtained chitosan had a degree of deacetylation (DA) of 84 ± 2.7 and a molecular weight of 136 kDa, which indicated that a good film had formed. The films composed of CHI and GLY (20 wt%) exhibited the best mechanical properties compared to the neat chitosan film. The percentage of elongation at break increase to over 700 % in the films that contained 40 % GLY, and these films also exhibited the highest values for the water vapor transmission rate (WVTR) of 79.6 ± 1.9 g m² h^?1 and a yellow color (b _o  = 17.9 ± 2.0) compared to the neat chitosan films (b _o  = 8.8 ± 0.8). For the structural properties, the Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction analyses revealed an interaction in the acetamide group and changes in the crystallinity of plasticized films. The scanning electron micrographs revealed that all formulations of the chitosan films were smooth, and that they did not contain aggregations, pores or microphase separation. The thermal analysis using differential scanning calorimetry (DSC) revealed a glass transition temperature (Tg) of 130 °C for neat chitosan film, but the addition of SOR or GLY elicited a decrease in the temperature of the peak (120 °C). In addition, the antimicrobial activity of the chitosan films was evaluated against Listeria monocytogenes, and reached a reduction of 2 log after 24 h. The plasticizer concentration of 20 % GLY is sufficient for obtaining flexible chitosan films with good mechanical properties, and it could serve as an alternative as a packaging material to reduce environmental problems associated with synthetic packaging films.     

Exfoliation and Decoration of Graphene Sheets with Silver Nanoparticles and Their Antibacterial Properties

High quality graphene sheets (GRP) have been exfoliated using facile one pot method through direct ultrasonication of graphite in the presence of polyvinyl alcohol. The GRP were decorated with silver nanoparticles (AgNPs) producing graphene–silver nanoparticle composites. The effect of variation of graphite and silver salt mass ratios on the morphology and performance of produced composites was studied. The size of AgNPs decorated on GRP has been tuned with synthesis method optimization. The average size of AgNPs was found to be in the range of 8.6–15.6 nm. Cotton–polyester blend textile fabrics were treated with the new smart developed composite as antibacterial agent producing new composites. A significant inhibition of bacterial growth has been observed for graphene–silver nanoparticle composite and the antibacterial efficiency was optimized. The clear inhibition zone for textiles treated with new developed composite and AgNPs alone was recorded as 12 and 1.75 mm respectively, achieving more than six fold improvement.     

Green Synthesis and Antioxidant Study of Silver Nanoparticles of Root Extract of <Emphasis Type="Italic">Sageretia thea</Emphasis> and Its Role in Oxidation Protection Technology

Development of environmentally friendly synthesis of nanoparticles is one of the important areas of research in nanotechnology. In present study silver naopartticles (AgNPs) of root extract of Sageretia thea (S. thea) were synthesized at room temperature. The synthesized AgNPs were characterized by UV. Visible spectroscopy (UV), scanning electron microscopy (SEM), X-ray diffraction (XRD), energy dispersive spectroscopy (EDX), transmission electron microscopy (TEM), dynamic light scattering (DLS) and Fourier transform infrared (FT-IR) spectroscopy. Formation of AgNPs was confirmed by visual examination the colour change from yellow to brick red due to surface Plasmon resonance band at 435 nm. SEM and TEM analysis of synthesized AgNPs revealed spherical morphology with average particle size 25 nm. Crystalline nature of the AgNPs in face centered cubic structure is evident from the selected area electron diffraction (SAED) and XRD pattern. The presence of elemental Ag was confirmed by EDX analysis at 3kv. Different functional groups which responsible for reduction and stabilization of reaction medium was confirmed by FTIR spectroscopy. The biosynthesized AgNPs showed strong DPPH and dye protection radical scavenging assay while modest hydrogen peroxide radical scavenging assay as compare to crude extract. The present investigations suggest that biosynthesized nanoparticles have a high potential for use in the preparation of drugs used against various diseases and also a promising candidate for many medical applications.     

Tailor Made Thin Film Composite Membranes: Potentiality Towards Removal of Hydroquinone from Water

The study investigated the use of thin film composite membrane (TFC) as a potential candidate for hydroquinone removal from water. Thin film composite membranes were prepared by polyamide coating on Polysulfone asymmetric membrane. FTIR study was performed to verify the Polysulfone as well as polyamide functionality. TFC membrane was characterized by contact angle, zeta potential, scanning electron microscopy studies. The salt rejection trend was seen from 500 to 1000 mg/L. The membrane is marked by permeability co-efficient B based on solution diffusion studies. The value is 0.98 × 10^?6 m/s for NaCl solution at 1.4 MPa. The separation performance was 88.87% for 5 mg/L hydroquinone at 1.4 MPa. The separation was little bit lowered in acid medium because of the nature of the membrane and feed solute chemistry. The ‘pore swelling’ and ‘salting out’ influenced hydroquinone separation in the presence of NaCl. The hydroquinone separation was 80.63% in 1000 mg/L NaCl solution. In acidic pH, NaCl separation was influenced much more compared to hydroquinone. The separation is influenced by field water matrix.     

Effect of Gamma Radiation on the Properties of Crosslinked Chitosan Nano-composite Film

Chitosan nano-composite film crosslinked by citric acid and with glycerol as plasticizer and MgO as antibacterial agent was prepared by casting method. MgO nanoparticles were synthesized via calcination method in furnace at 500 °C for 4 h and characterized by X-ray diffraction and transmission electron microscope. The chitosan nano-composite film with composition chitosan/citric/glycerol/magnesium oxide (1 wt%:1 wt%:75 vol%:10 wt%) has high mechanical properties than other films. The effects of different irradiation doses on the mechanical, thermal and antibacterial activity were investigated. The tensile strength enhanced by increasing irradiation dose up to 10 kGy and the elongation negligible changed as irradiation dose increased. The thermal stability slightly increased up to dose 2.5 kGy then decreased with dose increment. The antimicrobial activity film was studied against white mulberry-borne bacterial pathogens either Gram positive or Gram negative bacteria and has positive impact of gamma irradiation on the antimicrobial activity. The use of the selected chitosan nano-composite film which irradiated by dose of 2.5 kGy and has magnesium oxide of average particle size 54.3 nm as new packaging materials found to improve storage quality and shelf-life of mulberry fruit.     

Novel Tough Crystalline Blends of Polylactide with Ethylene Glycol Derivative of POSS

Blending of polylactide (PLA) with low stereoregularity and polyhedral oligomeric silsesquioxane grafted with arms of poly(ethylene glycol) methyl ether, acting as a plasticizer, allowed us previously to obtain a novel stable elastomeric-like material. The present contribution focuses on the properties of semi-crystalline PLA plasticized with this compound. Melt blends of PLA with 5–15 wt% of the plasticizer, were compression molded, quenched and annealed, which enabled cold-crystallization. The glass transition temperature of the blends and their drawability depended on their crystallinity and plasticizer content. The best ductility was reached at the plasticizer content of 15 wt%; the achieved strain at break was 6.5 (650%) and 1.3 (130%), for the quenched and annealed material, respectively. The latter value exceeded 20 times the strain at break of neat crystalline PLA. The tensile toughness of the annealed 15 wt% blend was 12 times larger than that of crystalline PLA. Moreover, annealing of 15 wt% blend improved its yield strength by 40%. Despite the two peaks of the loss modulus, indicating the two glass transitions in this blend, no heterogeneities were found by scanning electron microscopy, indicating that the plasticizer enriched phase formed instead of distinct inclusions of the plasticizer.     

Stability of Aqueous Suspensions of Medium-Chain-Length Poly-3-Hydroxyalkanoate Particles

Although poly-3-hydroxyalkanoates (PHAs) and particularily medium-chain-length (mcl)-PHAs are likely to find industrial applications in a latex form, very few studies have examined their behavior in aqueous suspension and none have examined the dense suspensions required commercially. For this reason, the stability of mcl-PHA latexes containing saturated aliphatic (65 mol% 3-hydroxynonanoate, PHN), and for the first time, with vinyl (PHNU) or carboxylated side chains was examined. At 4 g L^?1 with no stabilizing agent, PHNU nanoparticles (199.4 ± 3.6 nm) were significantly smaller than those of PHN (211.5 ± 6.4 nm) while carboxylated PHN nanoparticles (76.1 ± 6.4 nm) were substantially smaller than those of either PHN or PHNU with particles stable for more than 110 days. Increasing the PHN concentration to 10 g L^?1 also resulted in stable latexes but with larger particles (410.8 ± 5.2 nm). Adjusting the pH of the suspending medium (water) before addition of the polymer (dissolved in acetone) resulted in much smaller PHN particles at pH = 11.3 (134 ± 2 nm) than at pH = 4.3 (312 ± 8 nm) at a 4 g L^?1 final polymer concentration. Zeta potentials of PHN suspensions decreased with pH, likely due to the carboxyl end groups. Above a pH of 4.0, adjusting the pH after particle formation had little effect. NaCl addition could be used to agglomerate and ultimately precipitate the particles. Stabilizers such as surfactants will likely be required to produce denser mcl-PHA latexes with suitable particle size for certain applications such as coatings and toner production.     

A novel method for the preparation of silver/chitosan-O-methoxy polyethylene glycol core shell nanoparticles

Uniformly sized silver/chitosan-O-methoxy polyethylene glycol (chitosan-O-MPEG) core shell nanoparticles with different degree of substitution were synthesized. Thus, N-phthaloyl chitosan is reacted with polyethylene glycol monomethyl ether iodide in the presence of silver oxide by the following steps. At first, amino groups of chitosan are protected by fourfold excess of phthalic anhydride. Then N-phthaloyl chitosan is reacted with an appropriate amount of monomethyl ether iodide in the presence of silver oxide and lastly N-phthaloyl groups are removed to yield silver/chitosan-O-MPEG core shell nanoparticles. Structure of prepared silver/chitosan-O-MPEG core shell nanoparticles have been characterized by UV/Vis spectroscopy, transmission electron microscopy (TEM), Fourier transform infrared (FT-IR), X-ray diffraction, and scan electron microscopy (SEM-EDX). Experimental results revealed that the prepared silver core particles had the size 18?±?2?nm. Core shell structure with chitosan-O-MPEG-coating had the size 40?±?2?nm.     

Green Synthesis of Silver Nanoparticles and Study of Their Antimicrobial Properties

One of the major disadvantages of polymers when used in food-contact applications is that they are very susceptible to microbial attack. On the other hand, silver nanoparticles have received increased attention as novel antimicrobial agents. Therefore, the introduction of silver nanoparticles into conventional polymers results in new materials with improved properties. In this investigation, colloidal silver nanoparticles using an environmentally friendly procedure were synthesized. An aqueous solution of AgNO₃ was used as a silver precursor with ‘green’ reducing agents either different types of honey, or β-d-glucose. In the first case, different pH values, as well as the addition of poly(ethylene glycol), PEG were studied, while in the latter, the effect of reduction time in the presence of PEG with various average molecular weights was examined. Properties of the nanoparticles were measured using X-Ray diffraction, UV–Vis and FTIR spectroscopy. Using honey it seems that spherical particles are produced with the smaller average particle size obtained at pH 8.5. Use of honey has the advantage of being a natural product, although its main drawback is that its composition varies and it cannot be predefined to result in reproducible results. Use of β-d-glucose results in stable silver nanoparticles with small average particle size after 24 h reduction. The addition of low molecular weight PEG seems to be beneficial in the production of stable nanoparticles. Finally, the antimicrobial activity of the nanoparticles produced was investigated at different concentrations on both Gram positive and negative bacteria, such as Bacillus cereus, Bacillus subtilis, Escherichia coli and Staphylococcus aureus.     

Vegetable Oil Based Polyurethane Containing 1,2,3-Triazolium Functional Groups as Antimicrobial Wound Dressing

Preparation of antimicrobial polyurethane wound dressing membranes from a mixture of castor oil and a novel soybean oil-based polyol containing 1,2,3-triazolium rings (QTSBO) was described in this research. QTSBO was prepared through N-alkylation of 1,2,3-triazole functional soybean oil (TSBO) with methyl iodide, and TSBO was synthesized from an azidated soybean oil and propargyl alcohol through click reaction. The excellent tensile strength of these dressings under dry state and minimum deterioration of this property at fully hydrated state guaranteed the mechanical protection of wounds during the entire period of the healing process. The measured quantities of equilibrium water absorption and water vapor transmission rate for the optimized dressings confirmed the applicability of the selected formulations for the preservation of proper moist environment over low exuding wounds. The cyto-compatibility of dressings was verified by the excellent ability of the dressings to support the growth and proliferation of dermal fibroblasts. Due to the presence of 1,2,3-triazolium rings the dressing showed efficient antimicrobial activity against different bacterial and fungal stains. Therefore, these dressing could promote wound healing by preserving moist and hygienic environment over the wound bed.     

Laboratory waste minimization by recovery of silver as nano-silver colloidal dispersion from waste silver chloride

The use of cyclic experiments, where the product of one reaction becomes the starting material for the next experiment, was proposed as an effective protocol for waste minimization in an educational lab. A simple, cheap and pollution-free method was developed for recovering silver as nano-silver colloidal dispersion from waste silver chloride in the laboratories of the Faculty of Health, Safety and Environment. Silver nanoparticles of the size 5–18 nm were recovered in the presence of sodium borohydride as a reducing agent and polyvinylpyrrolidone as a stabilizer agent. The nano-silver particles were studied for their formation, structure, stability and size using UV–Vis spectroscopy, transmission electron microscopy and dynamic light scattering techniques. The antibacterial assays of nanoparticles showed satisfactory results for Escherichia coli ATCC25922, Staphylococcus aureus ATCC 29213, and Acinetobacter baumanii (Clinical isolate). A laboratory experiment was designed in which students synthesize yellow colloidal silver solution from chemical waste silver chloride and estimate particle size using visible spectroscopy.     

Blending of Epoxidised Palm Oil with Epoxy Resin: The Effect on Morphology, Thermal and Mechanical Properties

Epoxy resin prepared by the reaction of a diglycidyl ether of bisphenol A (DGEBA) and m-xylylenediamine (m-XDA) was modified with 10% wt of epoxidized palm oil (EPO). The EPO was first pre-polymerized with m-XDA at various temperatures and reaction times. The resulting product was then mixed with the epoxy resin at 40?°C and allowed to react at 120?°C for another 3?h. The fully reacted DGEBA/m-XDA/EPO blend was characterized by using scanning electron microscopy (SEM), differential scanning calorimetry (DSC), thermal gravimetric analysis, tensile test, hardness indentation and dynamic mechanical analysis. The SEM study shows that different types of morphology, ranging from phase separated to miscible blends were obtained. A miscible blend was obtained when the m-XDA and EPO were reacted for more than 2?h. The results from DSC analysis show that the incorporation of EPO at 10% wt in the epoxy blend reduced the glass transition temperature (T _g). The lowered T _g and mechanical properties of the modified epoxy resins are caused by a reduction in crosslinking density and plasticizer effect.     

Fabrication of Biodegradable Superabsorbent Using RSM Design for Controlled Release of KNO<Subscript>3</Subscript>

Present study envisaged the sequential experimental design approach for the development of biodegradable Gelatin-Tapoica/polyacrylamide superabsorbent. Percentage water uptake efficacy of candidate sample was optimized using Response Surface Methodology (RSM) design under microwave irradiation. Different process variables such as potassium persulphate and ammonium persulphate (KPS:APS) ratio, pH, reaction time concentration of acrylamide and N,N-methylene-bis-acrylamide (MBA) were investigated as a function of percentage swelling using sequential experimental design. Maximum liquid efficacy of 1550% was obtained at KPS:APS?=?1.0:0.5; acrylamide?=?7.67?×?10^?1 mol L^?1; MBA?=?1.76?×?10^?2 mol L^?1; pH 10 and time?=?110 s. The 3D crosslinked network formed was characterized using Fourier Transformation Infrared spectroscopy (FTIR), X-ray diffraction (XRD), Scanning Electron Microscopic (SEM) techniques and thermal stability was ensured by Thermal gravimetric Analysis/Differential Thermal Analysis/Differential Thermal Gravimetric (TGA/DTA/DTG) studies. Superabsorbent synthesized could increase the moisture content in different type of soils and was found to enhance the water-holding capability of the soil upto 60 days in clayey, 40 days in sandy and 51 days in mixture of two soils under controlled conditions. Further, candidate polymer was investigated for the in-vitro controlled release of the KNO₃ with diffusion exponent ‘n’ was found to be 0.4326 indicating Fickian type diffusion. Also, initial diffusion coefficient (D_I?=?3.49?×?10^?5 m² h^?1) was found to be greater than the lateral diffusion coefficient (D_L?=?3.76?×?10^?6 m² h^?1) indicated rapid release of KNO₃ during initial hours with slow release afterwards. The ecofriendly nature of the synthesized polymer was also tested by conducting biodegradation studies and it was found to degrade upto 94% and 88.1% within 70 days with degradation rate of 1.34 and 1.26% per day using composting method and vermicomposting method respectively. So, the synthesized candidate polymer was found to be boon for agriculture-horticulture sector with wide applicability.     

Comparison of the Effect of Plasticizers on PHBV—and Organoclay—Based Biodegradable Polymer Nanocomposites

The aim of this work was to evaluate the effect of different plasticizers on the morphology, crystallization, and mechanical properties of poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV)/organomodified montmorillonite (OMt) nanocomposites. We investigated three different plasticizers: dioctyl phthalate (DOP), a commonly used additive in the polymer industry, and two natural and biodegradable plasticizers: epoxidized soybean oil (ESO) and triethyl citrate (TEC). The nanocomposites with 3 wt% OMt were obtained by melt processing in an internal mixer. The plasticizers were used alone or in combination with clay in a concentration of 10 wt%. X-ray diffraction and scanning electron microscopy results revealed a partially intercalated structure. The degree of crystallinity was higher for all of the samples compared to neat PHBV, although the melting temperature decreased with the use of plasticizers combined with OMt. The impact strength results were dependent on the interaction between the components of the system. Triethyl citrate was the most effective plasticizer due to its more pronounced interaction with the PHBV matrix, which yielded improvements in processing conditions and PHBV’s flexibility and impact properties.     

Utilizing of Sugar Refinery Waste (Cane Molasses) for Production of Bio-Plastic Under Submerged Fermentation Process

In the present study, depending upon the availability and cheaper cost, different carbon source were tested for the production of PHAs (Polyhydroxyalkonoates) by soil bacterium Pseudomonas aeruginosa and it was found that sugar refinery waste (cane molasses) produced the maximum PHA (biodegradable polymer) which is precursor for bio-plastic development. Urea served as potent nitrogen source over other inorganic nitrogen sources in bio-plastic synthesis. Effect of different physical parameters viz; pH, temperature and agitation speed were also studied on PHA production. Batch cultivation kinetics under optimized cultural and physical condition showed maximum cell mass and PHA concentration of 7.32?±?0.2 and 5.60?±?0.3?g/L, respectively after 54.0?h of cultivation. Sugar refinery waste (Total sugar 4%) and urea (0.8%) improved the economics of the process which exhibited a yield (Y_P/X) of 0.70 with productivity of 0.11?g/L/h. PHA was further characterized as PHB by using Fourier Transform Infra-red Spectroscopy (FT-IR).     

Processing and characterization of a new biodegradable composite made of a PHB/V matrix and regenerated cellulosic fibers

In this study, a biodegradable composite consisting of a degradable continuous cellulosic fiber and a degradable polymer matrix—poly(3-hydroxybutyrate)-co-poly(3-hydroxyvalerate (PHB/V with 19% HV)—was developed. The composite was processed by impregnating the cellulosic fibers on-line withPHB/V powder in a fluidization chamber. The impregnated roving was then filament wound on a plate and hot-pressed. The resulting unidirectional composite plates were mechanically tested and optically characterized by SEM. The fiber content was 9.9 ±0.9 vol% by volumetric determination. The fiber content predicted by the rule of mixture for unidirectional composites was 13.8 ±1.4 vol%. Optical characterization showed that the fiber distribution was homogeneous and a satisfactory wetting of the fibers by the matrix was achieved. Using a blower to remove excess matrix powder during processing increased the fiber content to 26.5 ±3.3 vol % (volumetric) or 30.0 ±0.4 vol% (rule of mixture). The tensile strength of the composite parallel to the fiber direction was 128 ±12 MPa (10 vol% fiber) up to 278 ±48 MPa (26.5 vol% fiber), compared to 20 MPa for the PHB/V matrix. The Young’s modulus was 5.8 ±0.5 GPa (10 vol% fiber) and reached 11.4 ±0.14 GPa (26.5 vol% fiber), versus 1 GPa for the matrix.     

Optimized Removal of Acid Blue 62 from Textile Waste Water by SBA-15/PAMAM Dendrimer Hybrid Using Response Surface Methodology

SBA-15/PAMAM Nano adsorbent was synthesized by the proficiency of SBA-15 as an original compound, 3-chloropropyltrimethoxysilane as a bridge chemical compound and polyamidoamine dendrimer (PAMAM) in the role of a multifunctional amine end group for adsorption of acid blue 62 (AB62) from aqueous media. The synthesized adsorbent was characterized by transmission electron microscope, field emission scanning electron microscope and Fourier-transform infrared spectroscope. A response surface methodology was employed to evaluate the simple and amalgamated factors of the operating variables subtending initial pH (2–12), adsorbent dosage(0.01–0.03 g), contact time (5–120 min), initial dye concentration (40–600 ppm) and temperature (25–45?°C) to optimize the operating statues of the treatment method. These parameters were altered at five levels pursuant to the central composite design to appraise their effects on AB62 removal through analysis of variance. Analysis of variance represented a high coefficient of definition amount (R²?=?0.9999) and acceptable prediction quadratic polynomial model was concluded which ascertain the suitability of the model and a high correlation among the predicted and empirical amounts. Utmost color removal efficiency was auspicated and empirically accredited. The optimum conditions relied on acquired results for AB62 removal were at an initial pH of 2, adsorbent dosage of 0.03 g SBA-15/PAMAM, dye concentration of 40 mg l^?1, time contact of 60 min and temperature of 25?°C.     

Cellulose Fiber Isolation and Characterization from Sweet Blue Lupin Hull and Canola Straw

In this study, cellulose fibers were removed from crop by-products using a combination of sodium hydroxide treatment followed by acidified sodium chlorite treatment. The objective was to obtain high recovery of cellulose by optimizing treatment conditions with sodium hydroxide (5–20%, 25–75 °C and 2–10 h) followed by acidified sodium chlorite (1.7%, 75 °C for 2–6 h) to remove maximum lignin and hemicellulose, as well as to investigate the effect of lignin content of the starting materials on the treatment efficiency. Samples were characterized for their chemical composition, crystallinity, thermal behavior and morphology to evaluate the effects of treatments on the fibers’ structure. The optimum sodium hydroxide treatment conditions for maximum cellulose recovery was at 15% NaOH concentration, 99 °C and 6 h. Subsequent acidified sodium chlorite treatment at 75 °C was found to be effective in removing both hemicellulose and lignin, resulting in higher recovery of cellulose in lupin hull (~?95%) and canola straw (~?93%). The resultant cellulose fibers of both crop by-products had increased crystallinity without changing cellulose I structure (~?68–73%). Improved thermal stabilities were observed with increased onset of degradation temperatures up to 307–318 °C. Morphological investigations validated the effectiveness of treatments, revealing disrupted cell wall matrix and increased surface area due to the removal of non-cellulosics. The results suggest that the optimized combination of sodium hydroxide and acidified sodium chlorite treatments could be effectively used for the isolation of cellulose fibers from sweet blue lupin hull and canola straw, which find a great number of uses in a wide range of industrial applications.