Destruction of EDTA using Ce(IV) mediated electrochemical oxidation: a simple modeling study and experimental verification

Mediated electrochemical oxidation (MEO) is a recent development in the environmental research field for the complete destruction of organic pollutants. This study presents the destruction of EDTA by cerium(IV) MEO process in nitric acid medium. The destruction reaction was carried out in a continuous stirred tank reactor under various conditions. A simple kinetic model was developed to analyze and simulate the organic destruction in the MEO process. The model was based on the calculation of the total mass balance, the component mass balance, and the energy balance in the reactor and also in the heating jacket. The sensitivity to key operating conditions such as the initial EDTA concentration (50-200 mM), EDTA feeding time (30-180 min), reaction temperature (323-363 K), and the rate laws corresponding to zero-, first-, second-, and third-order reaction were analyzed. It was found that the model simulated agreed well with the experimental data for EDTA oxidation. The results obtained showed the suitability of the MEO process for the effective mineralization of high concentrations of EDTA.     

Studies on electrochemical recovery of silver from simulated waste water from Ag(II)/Ag(I) based mediated electrochemical oxidation process

In the Ag(II)/Ag(I) based mediated electrochemical oxidation (MEO) process, the spent waste from the electrochemical cell, which is integrated with the scrubber columns, contains high concentrations of precious silver as dissolved ions in both the anolyte and the catholyte. This work presents an electrochemical developmental study for the recovery of silver from simulated waste water from Ag(II)/Ag(I) based MEO process. Galvanostatic method of silver deposition on Ti cathode in an undivided cell was used, and the silver recovery rate kinetics of silver deposition was followed. Various experimental parameters, which have a direct bearing on the metal recovery efficiency, were optimized. These included studies with the nitric acid concentration (0.75-6M), the solution stirring rate (0-1400 rpm), the inter-electrode distance between the anode and the cathode (2-8 cm), the applied current density (29.4-88.2 mA cm(-2)), and the initial Ag(I) ion concentration (0.01-0.2M). The silver recovered by the present electrodeposition method was re-dissolved in 6M nitric acid and subjected to electrooxidation of Ag(I) to Ag(II) to ascertain its activity towards Ag(II) electrogeneration from Ag(I), which is a key factor for the efficient working of MEO process. Our studies showed that the silver metal recovered by the present electrochemical deposition method could be reused repeatedly for MEO process with no loss in its electrochemical activity. Some work on silver deposition from sulfuric acid solution of different concentrations was also done because of its promising features as the catholyte in the Ag(II) generating electrochemical cell used in MEO process, which include: (i) complete elimination of poisonous NO(x) gas liberation in the cathode compartment, (ii) reduced Ag(+) ion migration across Nafion membrane from anolyte to catholyte thereby diminished catholyte contamination, and (iii) lower cell voltage and hence lesser power consumption.     

Electrochemical and FTIR studies of the mutual influence of lead(II) or iron(III) and phenol on their adsorption from aqueous acid solution by modified activated carbons

Cyclic voltammetry and spectral FTIR studies of the influence of activated carbon surface modification on the co-adsorption of metal cation (lead or iron) and phenol from aqueous acidic solution were carried out. The diversity in surface chemical structure was achieved by applying different procedures of inorganic matter removal and by modifying the carbon samples in various ways: heating under vacuum, aminoxidation in an ammonia-oxygen atmosphere, oxidation with concentrated nitric acid. The quantities of adsorbed metal ions (Pb(2+) or Fe(3+)) and phenol from solutions containing cation or phenol separately or in a mixture were determined. The adsorption capacity from acidic aqueous acidic solution depends on the chemical properties of the activated carbon surface (e.g., decrease in phenol adsorption with relative lower basicity of the adsorbent). The electrochemical parameters of electrodes made from the carbon samples were estimated, and some possible electrochemical reactions were determined from voltammograms recorded in acid electrolyte solution containing adsorbed species (separately or as a mixture). Relationships were found between metal ion adsorption and electrochemical behavior of Pb(2+)/Pb(4+) and Fe(3+)/Fe(2+) couples on the one hand, and the presence of phenol in the solutions tested and the influence of surface chemistry of the carbon electrodes on electrochemical processes on the other. The changes in adsorption capacity with respect to the adsorbates used and the changes in FTIR spectra of the carbons as a result of adsorption and/or coupling phenol molecules are discussed.     

外负载Ce-TiO2/活性炭复合体对亚甲基蓝光催化

用超临界流体沉积法处理过的活性炭(AC)为载体,钛酸丁酯为前驱物,硝酸铈为掺杂剂,乙醇为溶剂,制备了外负载TiO2-Ce/Csurf复合材料。在紫外灯照射下,以亚甲基蓝溶液为标准模拟降解物,研究了复合体不同热处理温度、不同浓度、不同亚甲基蓝浓度、不同铈掺杂量以及不同反应温度对光催化性能的影响。结果表明:外负载催化剂的催化性能要高于纯TiO2和体负载催化剂。铈离子掺杂能抑制TiO2晶粒生长,阻碍了TiO2由锐钛矿型向金红石型的转变。当铈离子掺杂量为1.5%,热处理温度为600℃,亚甲基蓝溶液初始浓度为5.5 mg/L,样品浓度为1.5 g/L时,光催化性能最好。     

Electrochemical destruction of p-chlorophenol and p-nitrophenol -- Influence of surfactants and anode materials

The electrochemical oxidative removal of p-chlorophenol and p-nitrophenol was studied by cyclic voltammetry (CV) and constant current electrolysis on commercially available graphite and titanium substrate insoluble anodes (TSIA). The effect of cationic cetyl trimethylammonium bromide (CTAB), anionic sodium dodecyl sulphate (SDS) and non-ionic polyoxyethylene(23)lauryl ether (Brij-35) surfactants, which prevent adherent film formation on the electrode surface were also studied. CV experiments indicate that p-chlorophenol exhibits a relatively higher tendency for film formation on graphite and that sodium chloride is a better medium for the destruction of phenols. The electrochemical oxidation of phenols under galvanostatic conditions in chloride medium with CTAB enhanced the detoxification process with significantly lower fouling effects on TSIA. The surfactants, however, did not improve phenol removal on graphite under identical experimental conditions. A charge of 2.5F per mol was found to be sufficient to achieve 44-48% removal of phenol on both the electrodes in the absence of the surfactants. A 55-65% removal was achieved in the presence of the cationic surfactant on the TSIA electrode. Phenol was removed as a low molecular weight polymer (MW approximately 4450).     

Removal of methyl parathion from water by electrochemically generated Fenton's reagent

The electro-Fenton process was used to assess the degradation of methyl parathion (MP) in aqueous solutions. This oxidation process allows the production of hydroxyls radicals which react on the organic compounds, leading to their mineralization. Degradation experiments were performed either in perchloric, sulphuric, hydrochloric and nitric acid media under current controlled electrolysis conditions at different pH. The pH effect as well as the nature of the medium (i.e., the nature of the ions present in medium) on the degradation and mineralization efficiency were studied. The mineralization of the initial pollutant was investigated by total organic carbon measurements which show a complete mineralization at pH 3 in perchloric medium. The absolute rate constant of MP hydroxylation reaction was determined as (4.20+/-0.11)x10(9)M(-1)s(-1). Complete degradation of MP and its metabolites occur in less than 45min. Degradation reaction intermediates such as aromatic compounds, carboxylic acids and inorganic ions were identified and a mineralization pathway is proposed.     

Aniline degradation by electrocatalytic oxidation

The degradation of aniline solution in alkaline medium of pH 11.0 by electrocatalytic oxidation has been studied using an electrochemical reactor containing a SnO₂–Sb₂O₃–PtO anode and a Ti cathode, both of 54 cm² area. Hydroxyl radicals (HO^√) are produced at the anode, being tested with the trace catcher salicylic acid and phenol by spectrophotometery and high performance liquid chromatography. Intermediates dianiline, 4-anilino phenol and azobenzol were detected by gas chromatography–mass spectrometry. The existence of HO^√ produced in the aniline degradation was assayed with scavenger tertiary butanol. The results showed that electrocatalytic oxidation is an effective process for the degradation of aniline. A general reaction pathway that accounts for aniline degradation to CO₂ involving those intermediates is proposed.     

电化学方法用于酸性红B模拟废水脱色试验研究

本文研究了两种电极材料 (SnO2 Ti和RuO2 Ti)对酸性红B模拟废水的脱色效果 ,考察了不同 pH、电流密度(j)及外加电解质 (Na2 SO4/NaCl)对处理过程的影响。结果表明 ,两种电极材料都能对酸性红B染料废水进行有效脱色 ,主要是Cl-在电解过程中的间接氧化作用 ,同时也包括电极表面的直接氧化作用。     

Phenol nitration upon oxidation of nitrite by Mn(III,IV) (hydr)oxides

An interesting aspect of the chemistry of nitrite is the possibility for this compound to interact with other environmental factors and many oxidising species, which results in the oxidation of nitrite to nitrogen dioxide. This is a potentially interesting process that can lead to the formation of nitroaromatic compounds in the environment. In previous papers we have shown that nitrite can interact with dissolved Fe(III) and nitrate under irradiation, Fenton and heterogeneous photo-Fenton reagents, and semiconductor oxides such as TiO2, alpha-Fe2O3, and beta-FeOOH under irradiation. This paper reports on the interaction between nitrite/nitrous acid and the Mn(III,IV) (hydr)oxides beta-MnO2 and gamma-MnOOH, both in neutral solution under irradiation and in acidic conditions in the dark. beta-MnO2 and gamma-MnOOH originate from the oxidation of Mn(II) and play a key role in the redox cycling of manganese in the environment. These Mn(III,IV) (hydr)oxides show some photocatalytic activity, and they can act as thermal oxidants at acidic pH. The photoinduced oxidation of nitrite and the thermal oxidation of nitrous acid by Mn(III,IV) (hydr)oxides yield nitrogen dioxide and lead to the formation of nitrophenols in the presence of phenol. These processes can take place at the water-sediment or water-colloid interface in natural waters and on the surface of atmospheric particulate. Furthermore, the phenol/gamma-MnOOH/HNO2 system in dark acidic solution is an interesting model due to the formation of phenoxyl radical upon phenol monoelectronic oxidation by gamma-MnOOH. The kinetics of nitrophenol generation under such conditions indicates that phenol nitration is unlikely to take place upon reaction between phenoxyl and *NO2 and suggests a solution to a literature debate on the subject.     

外负载Ce-TiO_2/活性炭复合体对亚甲基蓝光催化

用超临界流体沉积法处理过的活性炭（AC）为载体,钛酸丁酯为前驱物,硝酸铈为掺杂剂,乙醇为溶剂,制备了外负载TiO2-Ce/Csurf复合材料。在紫外灯照射下,以亚甲基蓝溶液为标准模拟降解物,研究了复合体不同热处理温度、不同浓度、不同亚甲基蓝浓度、不同铈掺杂量以及不同反应温度对光催化性能的影响。结果表明：外负载催化剂的催化性能要高于纯TiO2和体负载催化剂。铈离子掺杂能抑制TiO2晶粒生长,阻碍了TiO2由锐钛矿型向金红石型的转变。当铈离子掺杂量为1.5%,热处理温度为600℃,亚甲基蓝溶液初始浓度为5.5 mg/L,样品浓度为1.5 g/L时,光催化性能最好。     

Electrocatalytic oxidation of methyl tert-butyl ether (MTBE) in aqueous solution at a nickel electrode

This study utilized the electrocatalytic characteristics of nickel electrode to perform degradation of methyl tert-butyl ether (MTBE) in aqueous solution. Lab experiments were conducted in a spiltless bath type cell equipped with a nickel electrode as working electrode, a platinum wire as counter electrode, and an Ag/AgCl electrode as reference electrode. Effects of controlled potential, supporting electrolyte, and solution pH on the efficiency of MTBE removal were examined under the control of the constant-potential conditions. Experiment results showed that the optimum electrolytic condition was operated at 0.35 V in a 1M KOH electrolyte solution, and the initial 20 mgl(-1) MTBE was reduced by 73% within 180 min under the optimum control. As using 1M Na2SO4 and 1M KCl as electrolyte, the efficiency of MTBE removal dropped to 60% and 50% under the similar controls. Comparing with various pH controls, the strong basic condition is favorable for electrocatalytic oxidation of MTBE in the Ni-electrolytic system. The efficiency of MTBE removal showed a rising trend with increasing initial pH of the solution. The formation of a redox NiOOH/Ni(OH)2 layer on the anode surface, which was observed on the SEM image, can explain that nickel plays a mediator role on improving electrocatalytic oxidation of MTBE at 0.35 V in a strong basic condition. The by-products of MTBE degradation were identified as acetone and CO(2) by GC/MS, and the distributions of carbon atoms in acetone, CO2, and MTBE were found 22%, 51%, and 27% through the optimum control of electrochemical oxidation.     

Electrochemical oxidation of benzene on boron-doped diamond electrodes

This work presents an electrochemical investigation of the benzene oxidation process in aqueous solution on boron-doped diamond (BDD) electrodes. Additionally, in order to determine the main products generated during the oxidation process, electrolysis and high performance liquid chromatography experiments were carried out. The complete degradation of this compound was performed aiming to a further application in waste water treatment. The cyclic voltammetry studies indicate that benzene is irreversibly oxidized in acid medium (H₂SO₄ 0.5 M) on the BDD electrode surface at 2.0 V versus Ag/AgCl in a diffusion controlled process. During the cycling, other products are generated, and a pair of peaks was observed that can be associated with the oxi-reduction of anyone of the following species: hydroquinone, benzoquinone, resorcinol or catechol. The electrolysis experiments were carried out at 2.4 and 2.5 V on the BDD electrode surface in a solution containing 1 × 10⁻² M of benzene (below the saturation concentration in aqueous solution), for 3 and 5 h, respectively. The main products measured were: hydroquinone, resorcinol, p-benzoquinone, catechol and phenol. The complete electrochemical benzene degradation was performed in the electrolysis experiments using a rotating BDD disc electrode (2.5 V for 5 h) and the main products detected were all measured at concentrations lower than 10⁻⁵ M in this condition. The boron-doped diamond electrode had proved to be a valuable tool for the electrochemical degradation of the benzene, a very stable chemical compound.     

电解质种类对电催化氧化降解苯酚的影响

研究了不同电解质对有机物电催化氧化性能的影响。以高温热解法制备了Ti/SnO2+Sb2O3阳极,用SEM和XRD对电极结构进行了表征。以苯酚为目标有机物,考察了Na2SO4、NaCl和NaNO33种不同电解质对苯酚降解效果的影响。用循环伏安法研究了苯酚在不同支持电解质条件下的电化学行为。采用碘量法测定了在不同电解质溶液中氧化性物质的生成量。研究结果表明,电极的活性涂层主要由SnO2和微量的Sb2O3组成,均匀完整地覆盖住了Ti基体表面。以NaCl为支持电解质时苯酚降解效果明显优于用Na2SO4、NaNO3为支持电解质,并且苯酚的降解主要以电极表面电化学生成的HClO和ClO-的间接化学氧化为主。以Na2SO4为支持电解质时有利于降低和稳定槽电压。在3种电解质条件下,苯酚的降解均遵循一级反应动力学规律。在降解过程中NaCl溶液中生成的氧化性物质浓度最大,且随降解时间延长逐渐增大。     

Evaluation of the efficiency of monopolar and bipolar BDD electrodes for electrochemical oxidation of anthraquinone textile synthetic effluent for reuse

The efficiency of the electrochemical degradation of synthetic wastewater containing an anthraquinone dye has been comparatively studied in two electrolytic cells with a synthetic boron-doped diamond (Si/BDD) as an anode. The first is an individual cell (Cell 1) with monopolar electrode BDD and the second (Cell 2) has two bipolar electrodes BDD self-polarized. The bulk electrolysis was performed at the same initial operating conditions in order to quantify the influence of the initial pH and current density on dye discoloration and global mineralization removal. The current efficiency and the consumption energy were also evaluated. When the same solutions have been comparatively treated with the two cells, a quite good mineralization is found in Cell 2. This result supposed more fraction of the applied current is used for the electrocombustion reaction on Cell 2 if compared to Cell 1 and small amount rest for the side reaction of oxygen evolution. The HPLC analyses confirmed this hypothesis and showed that the concentration trend of intermediates (sulfanilic acid, phthalate acid and salicylic acid) with electrolysis time was different on two cells. Phototoxicity tests show that the electrochemical oxidation with BDD electrodes could be useful as a pretreatment technique for reducing hazardous wastewater toxicity.     

Compound-specific chlorine isotope analysis of polychlorinated biphenyls isolated from Aroclor and Clophen technical mixtures

The combined electrochemical oxidation-solar-light/immobilized TiO₂ film process was conducted to degrade an azo dye, Reactive Black 5 (RB5). The toxicity was also monitored by the Vibrio fischeri light inhibition test. The electrochemical oxidation rapidly decolorized RB5 (55, 110 μM) with a supporting electrolyte of 2 g l⁻¹ NaCl at current density 277 A m⁻² and pH 4. However, TOC mineralization and A₃₁₀ removal were low. Additionally, the treated solution showed high biotoxicity. RB5 at 110 μM significantly retarded the de-colorization efficiency by using the solar-light/immobilized TiO₂ film process. The combined electrochemical oxidation-solar-light/immobilized TiO₂ process effectively increased the removal of color, A₃₁₀, and TOC. The toxicity was also significantly reduced after 3 h of solar irradiation. The results indicated that the low-cost combined process is a potential technique for rapid treatment of RB5.     

pH indications in aqueous organic photodecompositions with carbonyl and hydroxyl groups

A pH variation pattern during organic compound (ethylene glycol, phenol, and glucose) decomposition under UV/H2O2 of different schemes was observed. This method was successfully applied to reflect the organic carbon oxidation progress, especially the rapid chemical oxygen demand (COD) decrease timing in the later mineralization stage. The results were demonstrated in a sequential feed-batch advanced oxidation reactor, showing that pH can be used as an alternative indicator to provide complete oxidation and cycle time information.     

CWAO of phenol using CeO2/gamma-Al2O3 with promoter--effectiveness of promoter addition and catalyst regeneration

The effect of promoter addition on activity of CeO(2)/gamma-Al(2)O(3) was assessed via the CWAO of phenol. Adding Cu as the promoter rendered the most effective performance, followed by Mn, although the performance of Mn-promoted catalyst was inferior to CeO(2)/gamma-Al(2)O(3). Mineralization of phenol was effectively implemented at 160 degrees C using Cu-promoted catalyst (Ce15Cu5). Furthermore, at 180 degrees C this catalyst produced about 100% conversion of phenol (1h) and 95% removal of chemical oxygen demand (4h), higher than that of CeO(2)/gamma-Al(2)O(3). In contrast, Mn-promoted catalyst (Ce15Mn5) required a temperature above 220 degrees C for acceptable performance. Activity of re-used catalyst declined noticeably, due to deposits of carbonaceous compounds and leaching of metal ions. Regeneration with acetone rinsing after the first run was effective in recovering activity of Ce15Cu5, although after a second run further regeneration with acetone rinsing had only a moderate effect, due to residual carbonaceous deposits and the additive effect of leached metal species in each run. As an alternative to acetone, HCl or HNO(3) solution (0.01 M) was less effective at regenerating activity. In promoted catalysts, leached metal ions accounted for the majority of mineralization of phenol, while the solid catalyst played a dual role of initiator and terminator of free radicals. Despite a superior catalytic performance, leaching of Cu(2+) from the promoted catalyst caused a severe decline in activity and poses the problem of secondary pollution of treated wastewater. Therefore, addition of Cu, as well as other metal species, is unfavorable in promoting the CeO(2)/gamma-Al(2)O(3) catalyst.     

Removal of ammonia solutions used in catalytic wet oxidation processes

Ammonia (NH(3)) is an important product used in the chemical industry, and is common place in industrial wastewater. Industrial wastewater containing ammonia is generally either toxic or has concentrations or temperatures such that direct biological treatment is unfeasible. This investigation used aqueous solutions containing more of ammonia for catalytic liquid-phase oxidation in a trickle-bed reactor (TBR) based on Cu/La/Ce composite catalysts, prepared by co-precipitation of Cu(NO(3))(2), La(NO(3))(2), and Ce(NO(3))(3) at 7:2:1 molar concentrations. The experimental results indicated that the ammonia conversion of the wet oxidation in the presence of the Cu/La/Ce composite catalysts was determined by the Cu/La/Ce catalyst. Minimal ammonia was removed from the solution by the wet oxidation in the absence of any catalyst, while approximately 91% ammonia removal was achieved by wet oxidation over the Cu/La/Ce catalyst at 230 degrees C with oxygen partial pressure of 2.0 MPa. Furthermore, the effluent streams were conducted at a liquid hourly space velocity of under 9 h(-1) in the wet catalytic processes, and a reaction pathway was found linking the oxidizing ammonia to nitric oxide, nitrogen and water. The solution contained by-products, including nitrates and nitrites. Nitrite selectivity was minimized and ammonia removal maximized when the feed ammonia solution had a pH of around 12.0.     

Comparison of trip average in-vehicle and exterior CO determinations by continuous and grab sampling using an electrochemical sensing method

In air quality monitoring studies, continuous sampling is capable of reflecting real time variation of gas levels, however, with a margin of uncertainty related to the response time of the sensor and to the speed of concentration fluctuation. In contrast, grab sampling allows the determination of average gas concentration over the whole sampling period eliminating thus the uncertainties associated with the continuous method. As studies of in-vehicle carbon monoxide (CO) exposure often show rapidly fluctuating CO levels and are increasingly using the continuous electrochemical sensing method, the present activity aims at validating the suitability of the latter method for this monitoring task. For this purpose, an electrochemical CO sensing monitor was used to continuously monitor CO level inside and outside of a vehicle moving in an urban area, and to analyze the content of concomitantly taken grab samples. Trip-average CO levels measured using the two testing methods were compared. For CO levels higher than the instrument detection limit (1 ppm), the observed percent difference between continuous and grab sampling results varied within a fairly acceptable range (0.6–15.4%). The regression of continuous sampling data against grab sampling data revealed an average error of 6.9%, indicating the suitability of the continuous electrochemical method for monitoring in-vehicle and exterior average CO concentration under typical urban traffic conditions.     

Decolourisation of simulated reactive dyebath effluents by electrochemical oxidation assisted by UV light

This study is focused on the optimisation of the electrochemical decolourisation of textile effluents containing reactive dyes with the aim of making feasible-technically and economically-this method at industrial scale. Coloured waters were treated in continuous at low current density, to reduce the electrical consumption. Ti/PtO(x) electrodes were used to oxidize simulated dyebaths prepared with an azo/dichlorotriazine reactive dye (C.I. Reactive Orange 4). The decolourisation yield was dependent on the dyeing electrolyte (NaCl or Na(2)SO(4)). Dyeing effluents which contained from 0.5 to 20 gl(-1) of NaCl reached a high decolourisation yield, depending on the current density, immediately after the electrochemical process. These results were improved when the effluents were stored for several hours under solar light. After the electrochemical treatment the effluents were stored in a tank and exposed under different lighting conditions: UV light, solar light and darkness. The evolution of the decolourisation versus the time of storage was reported and kinetic constants were calculated. The time of storage was significantly reduced by the application of UV light. A dye mineralization study was also carried out on a concentrated dyebath. A TOC removal of 81% was obtained when high current density was applied for a prolonged treatment with recirculation. This treatment required a high electrical consumption.