ZSM-5沸石分子筛吸附-脱附VOCs的性能研究

以不同Si/Al比的ZSM-5分子筛为吸附剂,考察了硅铝比对其疏水性和吸附性能的影响.结果表明,随着Si/Al比的增加,其微孔孔体积和微孔表面积变大,当Si/Al100时,ZSM-5分子筛均具有良好的疏水性和对甲苯的选择性吸附能力,但脱附温度随之升高.同时,以4类VOCs(醇类、酯类、烃类、酮类)为吸附质,研究了ZSM-5分子筛吸附-脱附不同VOCs的性能.发现ZSM-5分子筛由于具有丰富的微孔结构更适合吸附小分子VOCs,对于同类VOCs分子,随着碳数的增加,分子大小和极性均增大,其与分子筛的作用力越强,热脱附温度越高,但VOCs在ZSM-5分子筛表面300℃左右就能脱附完全.     

焙烧温度对Fe2O3/SAPO-34催化剂低温NH3选择性催化还原NO性能的影响

采用尿素沉淀法制备了一系列Fe_2O_3/SAPO-34催化剂,考察了催化剂焙烧温度(200、300、400、500℃)对低温NH_3选择性催化还原(NH_3-SCR)NO性能的影响,并利用X射线衍射(XRD)、N_2吸附-脱附、原子吸收光谱(AAS)、场发射扫描电镜(FE-SEM)、X射线光电子能谱(XPS)、H_2程序升温还原(H_2-TPR)、NH_3程序升温脱附(NH_3-TPD)等多种手段对催化剂的表面结构和物理化学性质进行表征分析.XRD和FE-SEM分析表明,在较低的焙烧温度(400℃)下,铁物种能够高度均匀地负载在SAPO-34表面上.NH_3-TPD和H_2-TPR分析表明,高分散状态的Fe_2O_3使催化剂暴露出更多的强酸位和活性位,有利于提高催化剂的NH_3吸附和活化能力及氧化还原性能,从而使催化剂呈现出更高的低温SCR活性.BET和XPS分析表明,在较低的焙烧温度下,Fe_2O_3/SAPO-34催化剂具有更大的比表面积和更高的化学吸附氧比例,促进NO氧化为中间产物NO_2,从而加快低温SCR反应的进行.活性测试结果表明,300℃焙烧的Fe_2O_3/SAPO-34催化剂具有最佳的低温活性和较强的抗硫抗水性能,在空速为40000 h~(-1)的条件下,且反应温度为190~240℃时,NO转化率达90%以上且N_2选择性接近100%.     

ZSM-5分子筛疏水改性及催化H_2O_2氧化苯酚的性能研究

以甲苯为溶剂、三甲基氯硅烷(TMCS)为表面改性剂,采用液相接枝的方法对ZSM-5分子筛进行疏水化改性,通过XRD、FTIR、N2吸附-脱附、TG、水静态吸附试验等手段对改性前后的ZSM-5分子筛进行了表征,并将其应用于苯酚的吸附及催化氧化研究。结果表明:改性后ZSM-5分子筛仍保持原有的孔道结构,-Si(CH3)3基团接枝到孔道表面,使比表面积和孔容、孔径均有下降;改性后ZSM-5分子筛水静态吸附率由3.82%降至1.12%,疏水性得到明显提高;改性后ZSM-5分子筛对苯酚的吸附机理符合Langmuir模型,吸附动力学符合准二级动力学模型,且对水中苯酚的饱和吸附量由30.7mg/g增加到36.9mg/g;疏水改性后的分子筛负载MnO2催化H2O2氧化降解苯酚的效率可达86.2%,且其吸附过程与催化氧化过程具有协同效应。     

不同SAPO分子筛负载MnOx催化剂的低温NH3-SCR性能研究

以磷酸硅铝分子筛SAPO-5、SAPO~(-1)1和SAPO-34为载体,采用乙醇分散法制备了用于低温氨选择性还原(NH_3-SCR)NO_x的分子筛负载MnO_x催化剂.活性测试结果显示,3种分子筛催化剂均展现出优良的NH_3-SCR活性,但三者在低温区间的SCR活性存在较明显差异,其SCR活性顺序如下:MnO_x/SAPO-34MnO_x/SAPO-5MnO_x/SAPO~(-1)1.借助XRD、N2吸附-脱附、XPS、H2-TPR、NH_3-TPD、NH_3FT-IR等技术对催化剂的表面活性物种及表面酸性等进行表征分析,结果表明,MnO_x主要以无定型状态分散于载体上,负载后载体的比表面积和孔体积均有所下降.XPS和H2-TPR分析证实,不同分子筛载体上MnO_x的表面浓度与氧化态明显不同.NH_3-TPD和NH_3FT-IR分析揭示了催化剂表面均存在Bronsted酸位和Lewis酸位,其中,Lewis酸性位对低温SCR反应起着关键作用.研究表明,催化剂的催化性能会因载体不同而存在差异,高Mn4+表面浓度和丰富的Lewis酸性位对催化剂在低温区间实现优良的催化活性尤为重要.     

H-ZSM-5分子筛吸附-氧化NOx的研究

针对湿法脱硫后船舶尾气特点,考察了3种不同硅铝比的H-ZSM-5分子筛对船舶脱硫后尾气中NO_x的吸附-氧化过程及其影响因素,并采用TPD研究了干气下不同硅铝比的分子筛吸附饱和后的脱附情况.结果表明:干气条件下,硅铝比低的分子筛具有较好的吸附效果;硅铝比高的分子筛具有较好的抗水性,但从干气到饱和湿度下,硅铝比为300的分子筛的NO氧化率从36%降至18%;干气下,低温有利于分子筛的吸附-氧化;分子筛用量增加能够增加其对NO_x的吸附效果和氧化效果.TPD结果表明:NO和NO2共吸附在分子筛上,3种分子筛中脱附出的NO_x中NO2均占脱附总量的80%以上,但在600℃时,NO_x在分子筛上脱附仍不完全.     

纳米片层状ZSM-5分子筛制备及其对室内环境VOCs吸附性能

合成了1种新型分子结构的bola型表面活性剂,并以其为模板,以正硅酸乙酯、偏铝酸钠为硅源和铝源,按n（NaOH）∶n（NaAlO₂）∶n（SiO₂）∶n（SDA）∶n（H₂O）为30∶2.5∶120∶5∶4800进行配比,采用水热法制备出具有纳米片层结构的ZSM-5分子筛（H-ZSM-5）。采用扫描电镜、透射电镜、X射线和N₂吸脱附等技术表征所制备的片层ZSM-5分子筛。对传统ZSM-5、H-ZSM-5进行了甲醛分子静态吸附实验,发现H-ZSM-5分子筛静态吸附量显著高于传统微孔ZSM-5。采用较大分子直径的甲苯蒸汽分子评价吸附性能发现,纳米片层状H-ZSM-5分子筛具备吸附较大分子直径VOCs的能力,可以用于室内较大分子VOCs的净化去除。     

硅铝比对分子筛吸附氨氮性能的影响

基于X射线荧光光谱法确定的4种ZSM5分子筛硅铝比,分析了不同硅铝比分子筛吸附氨氮性能的差异,结合扫描电镜、X射线衍射分析结果,从分子筛的骨架组成、表面形貌和晶体结构角度,考察了硅铝比对分子筛吸附氨氮性能的影响机制;并探讨了分子筛骨架脱硅对其吸附性能的改善作用,为分子筛应用于污水厂尾水深度脱氮提供技术参考.结果表明,不同硅铝比分子筛的表面形貌、晶体结构与吸附氨氮性能具有显著差异：随着分子筛硅铝比增加,其结晶度下降、晶粒形态逐渐模糊、吸附容量降低;当实际硅铝比由35增大至237时,氨氮平衡吸附量由5.65mg/g降至0.41mg/g,由Langmuir吸附等温式确定的饱和吸附量由6.5963mg/g下降至0.4430mg/g.分子筛吸附过程符合准二级动力学模型,吸附速率受离子交换化学吸附作用机理控制,随着硅铝比升高分子筛的离子交换容量下降,其吸附速率降低.分子筛骨架脱硅能够显著改善其氨氮吸附性能,硅铝比为35的分子筛经碱蚀脱硅处理后,其氨氮平衡吸附量提高81.6%,该方法为改善分子筛吸附性能提供了一种有效的技术途径.     

改性MnO_x-CeO_2/石墨烯催化剂的低温SCR脱硝性能

通过水热法分别制备Co掺杂及Ti掺杂的Mn-Ce/石墨烯催化剂,并通过X射线衍射(XRD),X射线光电子能谱(XPS),拉曼(Raman)光谱,H_2程序升温还原(H_2-TPR)及NH_3程序升温脱附(NH_3-TPD)等表征手段对两种催化剂分别进行结构和理化性质的分析。再通过对比两种催化剂去除NO_x的催化活性,N_2选择性与抗硫性可知,Co掺杂Mn-Ce/石墨烯催化剂在低温情况下有较高的催化活性,并且很好地改善了Mn-Ce/石墨烯催化剂的N_2选择性及抗硫性。     

硅铝比对Cu/SSZ-13SCR活性位的影响

采用固态离子交换法制备了不同硅铝比（Si/Al=5,10,25）的Cu/SSZ-13分子筛催化剂,探究硅铝比对其NH₃选择性催化还原（NH₃-SCR）活性位的影响规律,并通过X射线衍射（XRD）,H₂程序升温还原（H₂-TPR）,NO_x程序升温脱附（NO_x-TPD）,NH₃程序升温脱附（NH₃-TPD）,原位红外实验（in situ DRIFTS）等手段进行物化性质表征.活性测试结果表明,当Cu负载量为4wt%时,不同硅铝比的Cu/SSZ-13具有显著差异的SCR活性;其中,Cu/SSZ-13（10）的SCR活性最佳,200~450℃温度范围内NO转化率均大于80%.XRD和H₂-TPR结果表明,硅铝比会影响Cu/SSZ-13的Cu物种的分布和氧化还原性.NO_x-TPD和NH₃-TPD结果表明,3种催化剂中Cu/SSZ-13（10）具有最多Cu²⁺离子,Cu²⁺离子可以为Cu/SSZ-13（10）提供更多的NO_x吸附位点和Lewis酸性位点,而Lewis酸性位是Cu/SSZ-13主要的低温SCR活性位点,因此有利于NH_3-SCR反应的进行.当硅铝比增加到25时,Cu/SSZ-13（25）的Lewis酸性位大量损失,导致其SCR活性明显下降.     

不同孔径HZSM-5协同低温等离子体催化降解甲苯性能研究

研究了HZSM-5分子筛孔径对其在等离子体场内催化降解甲苯的影响.采用化学液相沉积法对HZSM-5分子筛进行改性,利用XRD、氮气吸附脱附等方法表征样品的骨架结构和表面性质,并用择形吸附实验对样品孔径进行表征.同时,评价了HZSM-5分子筛体系中降解甲苯的性能,研究了分子筛吸附甲苯性能及臭氧的产量,并采用飞行时间质谱(TOF-MS)和气相色谱-质谱联用仪(GC-MS)分析了反应产生的有机副产物.结果表明:液相沉积法成功调控了HZSM-5孔径,样品孔径随沉积剂用量增加而减小;同时,样品均具有相同的MFI骨架结构,比表面积和孔容相差不大.HZSM-5的孔径尺寸对甲苯去除率影响不大,但对碳平衡有影响,孔径越大,碳平衡越好.孔径较大的HZSM-5分子筛对甲苯具有更大的吸附速率和吸附容量,同时更多臭氧参与反应,生成·OH和O·,促进甲苯深度氧化,减少副产物,提高碳平衡.     

Application of high silica zeolite ZSM-5 in a hybrid treatment process based on sequential adsorption and ozonation for VOCs elimination

In this study, a hydrophobic synthetic zeolite, namely ZSM-5 is chosen as an adsorbent/catalyst for toluene removal. Experimental results showed that toluene adsorption onto ZSM-5 was favourable, following a Langmuir adsorption isotherm model. ZSM-5 zeolite was regenerated using gaseous ozone at low temperature. Adsorbed toluene was oxidised, releasing mainly CO₂ and H₂O. Traces of oxidation by-products such as acetic acid and acetaldehyde were formed and remained adsorbed after the oxidativate regeneration with ozone. After four successive cycles of adsorption/ozonation, the adsorption efficiency was not affected (92%–99%). These results showed that volatile organic compound (VOC) removal by adsorption onto ZSM-5 zeolite followed by ozone regeneration could be used as a promising hybrid process for the control of VOC emissions in terms of efficiency.     

Effects of metal and acidic sites on the reaction by-products of butyl acetate oxidation over palladium-based catalysts

Catalytic oxidation is widely used in pollution control technology to remove volatile organic compounds. In this study, Pd/ZSM-5 catalysts with different Pd contents and acidic sites were prepared via the impregnation method. All the catalysts were characterized by means of N2 adsorption- desorption, X-ray fluorescence （XRF）, HE temperature programmed reduction （H2-TPR）, and NH3 temperature programmed desorption （NH3-TPD）. Their catalytic performance was investigated in the oxidation of butyl acetate experiments. The by-products of the reaction were collected in thermal desorption tubes and identified by gas chromatography/mass spectrometry. It was found that the increase of Pd content slightly changed the catalytic activity of butyl acetate oxidation according to the yield of CO2 achieved at 90%, but decreased the cracking by-products, whereas the enhancement of strong acidity over Pd-based catalysts enriched the by-product species. The butyl acetate oxidation process involves a series of reaction steps including protolysis, dehydrogenation, dehydration, cracking, and isomerization. Generally, butyl acetate was cracked to acetic acid and 2- methylpropene and the latter was an intermediate of the other by-products, and the oxidation routes of typical by-products were proposed. Trace amounts of 3-methylpentane, hexane, 2-methylpentane, pentane, and 2-methylbutane originated from iso4merization and protolysis reactions.     

Preparation and evaluation of aminopropyl-functionalized manganese-loaded SBA-15 for copper removal from aqueous solution

A novel material, aminopropyl-functionalized manganese-loaded SBA-15 (NH₂-Mn-SBA-15), was synthesized by bonding 3-aminopropyl trimethoxysilane (APTMS) onto manganese-loaded SBA-15 (Mn-SBA-15) and used as a Cu^2 + adsorbent in aqueous solution. Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction spectra (XRD), N₂ adsorption/desorption isotherms, high resolution field emission scanning electron microscopy (FESEM) and X-ray photoelectron spectroscopy (XPS) were used to characterize the NH₂-Mn-SBA-15. The ordered mesoporous structure of SBA-15 was remained after modification. The manganese oxides were mainly loaded on the internal surface of the pore channels while the aminopropyl groups were mainly anchored on the external surface of SBA-15. The adsorption of Cu^2 + on NH₂-Mn-SBA-15 was fitted well by the Langmuir equation and the maximum adsorption capacity of NH₂-Mn-SBA-15 for Cu^2 + was over two times higher than that of Mn-SBA-15 under the same conditions. The Elovich equation gave a good fit for the adsorption process of Cu^2 + by NH₂-Mn-SBA-15 and Mn-SBA-15. Both the loaded manganese oxides and the anchored aminopropyl groups were found to contribute to the uptake of Cu^2 +. The NH₂-Mn-SBA-15 showed high selectivity for copper ions. Consecutive adsorption–desorption experiments showed that the NH₂-Mn-SBA-15 could be regenerated by acid treatment without altering its properties.     

Regeneration of commercial selective catalyst reduction catalysts deactivated by Pb and other inorganic elements

The regeneration of commercial SCR(Selective Catalyst Reduction) catalysts deactivated by Pb and other elements was studied.The deactivated catalyst samples were prepared by chemical impregnation with mixed solution containing K_2SO_4,Na_2SO_4,CaSO_4,Pb(NO_3)_2and NH_4H_2PO_4.A novel method combining Ethylenediaminetetraacetic acid disodium salt(EDTA-2Na) and H_2SO_4solution(viz.catalysts treated by dilute EDTA-2Na and H_2SO_4 solution in sequence) was used to recover the activity of deactivated samples,and the effect was compared with single H_2SO_4,oxalic acid,acetic acid,EDTA or HNO_3 solutions.The surface structure,acidity and reducibility of samples were characterized by N_2adsorption–desorption,inductively coupled plasma optical emission spectrometer(ICP-OES),scanning electron microscopy(SEM),X-ray diffraction(XRD),X-ray fluorescence(XRF),H-2-temperature programmed section(H_2-TPR),NH3-temperature programmed desorption(NH3-TPD) and in situ DRIFTS.Impurities caused a decrease of specific surface area and surface reducibility,as well as Br?nsted acid sites,and therefore led to severe deactivation of the SCR catalyst.The use of an acid solution alone possibly eliminated the impurities on the deactivated catalyst to some extent,and also increased the specific surface area and Br?nsted acid sites and promoted the surface reducibility,thus recovered the activity partially.The combination of EDTA-2Na and H_2SO_4 could remove most of the impurities and improve the activity significantly.The removal of Pb should be an important factor for regeneration.Due to a high removal rate for Pb and other impurities,the combination of EDTA-2Na and H_2SO_4 solutions provided the best efficiency.     

Structures and catalytic performances of Me/SAPO-34 (Me = Mn, Ni, Co) catalysts for low-tem perature SCR of NOx by ammonia

Me/SAPO-34 (Me = Mn, Ni, Co) series of catalysts were prepared by a wetness impregnation method and investigated for the selective catalytic reduction of nitrogen oxides with ammonia (NH₃-SCR). Among them, Mn/SAPO-34 catalyst was found as the most promising candidate based on its superior low-temperature activity. The catalysts were characterized by X-ray diffraction (XRD), transmission electron microscopy images (TEM), nuclear magnetic resonance (NMR), X-ray photoelectron spectroscopy (XPS), temperature programmed reduction and desorption (TPR and TPD), and diffuse reflectance infrared Fourier transformed spectroscopy (DRIFTS) of NH₃/NO_x adsorption. Mn/SAPO-34 is obviously different from Ni/SAPO-34 and Co/SAPO-34 in the active species state and distribution. Surface MnO_x species which play an essential role in NO oxidation and NO₂ adsorption, act as better active sites than nickel and cobalt mostly in the form of the aluminates and silicates.     

Preparation and evaluation of aminopropyl-functionalized manganese-loaded SBA-15 for copper removal from aqueous solution

A novel material, aminopropyl-functionalized manganese-loaded SBA-15 (NH₂-Mn-SBA- 15), was synthesized by bonding 3-aminopropyl trimethoxysilane (APTMS) onto manganeseloaded SBA-15 (Mn-SBA-15) and used as a Cu²⁺ adsorbent in aqueous solution. Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction spectra (XRD), N₂ adsorption/ desorption isotherms, high resolution field emission scanning electron microscopy (FESEM) and X-ray photoelectron spectroscopy (XPS) were used to characterize the NH₂-Mn-SBA-15. The orderedmesoporous structure of SBA-15 was remained aftermodification. The manganese oxides were mainly loaded on the internal surface of the pore channels while the aminopropyl groups were mainly anchored on the external surface of SBA-15. The adsorption of Cu²⁺ on NH₂-Mn-SBA-15 was fitted well by the Langmuir equation and the maximum adsorption capacity of NH₂-Mn-SBA-15 for Cu²⁺ was over two times higher than that of Mn-SBA-15 under the same conditions. The Elovich equation gave a good fit for the adsorption process of Cu²⁺ by NH₂-Mn-SBA-15 and Mn-SBA-15. Both the loaded manganese oxides and the anchored aminopropyl groups were found to contribute to the uptake of Cu²⁺. The NH₂-Mn-SBA-15 showed high selectivity for copper ions. Consecutive adsorption-desorption experiments showed that the NH₂-Mn-SBA-15 could be regenerated by acid treatment without altering its properties.     

硅改性制备疏水性沸石分子筛蜂窝体

通过氢型沸石分子筛粉体与粘结剂、助剂和水混合成面团状后挤压成型,干燥焙烧,再通过四氯化硅疏水改性处理,制备了一种蜂窝状复合沸石分子筛吸附剂.通过低温N2吸附、XRD、吸苯等手段对所制备的分子筛蜂窝体进行表征和评价.结果表明所制备的复合沸石分子筛蜂窝体经过硅改性处理后,硅铝比由4提高至22,比表面和总孔容略降,P/P0=0.95时吸苯量比改性前稍高,达18.05%.相对湿度80%RH条件下（P/P0=0.95）苯的饱和吸附量还能达到15%,与改性前相比增加了1倍多,疏水性优良.     

Synergistic effects of non-thermal plasma-assisted catalyst and ultrasound on toluene removal

A wire-mesh catalyst coated by La_0.8Sr_0.2MnO₃ was combined with a dielectric barrier discharge (DBD) reactor for toluene removal at atmospheric pressure. It was found that toluene removal efficiency and carbon dioxide selectivity were enhanced in the catalytic packed-bed reactor. In addition, ozone and nitrogen monoxide from the gas effluent byproducts decreased. This is the first time that ultrasound combined with plasma has been used for toluene removal. A synergistic effect on toluene removal was observed in the plasma-assisted ultrasound system. At the same time, the system increased toluene conversion and reduced ozone emission.     

29种湿地填料对氨氮的吸附解吸性能比较

为筛选出性能更好的人工湿地填料,采用等温吸附-解吸试验,测定了29种天然和非天然人工湿地填料的孔隙率、渗透系数及其对NH₃-N的吸附-解吸特性. 结果表明:锯末、瓷砖、鸡蛋壳、瓷砂陶粒、火山岩等材料的孔隙率较大,瓷砂陶粒、海绵铁、石灰石、页岩陶粒、砾石等材料的渗透系数较大;Freundlich和Langmuir等温吸附方程能较好地拟合各填料对NH₃-N的吸附特征,通过Langmuir等温吸附方程计算,对NH₃-N的理论饱和吸附量居前5位的填料依次是火山岩(1.700 0 mg/g)、瓷砂陶粒(1.620 0 mg/g)、生物炭(1.353 0 mg/g)、沸石(1.350 0 mg/g)、石榴石(1.190 0 mg/g). 吸附速率的变化与填料吸附NH₃-N的途径密切相关. 吸附饱和的生物炭、焦炭、大理黏土、沸石、磁铁矿、石英砂主要通过离子交换作用吸附NH₃-N,稳定性好,解吸率均小于20%;瓷砂陶粒和火山岩对NH₃-N的解吸率分别为24.50%和35.51%,既有物理吸附也有离子交换作用. 火山岩、瓷砂陶粒、生物炭、沸石对较高浓度NH₃-N的吸附效果较好. 研究显示,火山岩、生物炭、瓷砂陶粒、沸石等适合作为人工湿地中吸附NH₃-N的填料.      

二氧化钛对地下水中砷硅的吸附及再生回用

二氧化钛(TiO_2)材料作为性能优异的吸附材料被广泛应用于地下水砷(As)的去除中.结果表明,地下水中共存硅离子(Si)会占据TiO_2的吸附位点,从而影响As的吸附及TiO_2材料的再生回用.本文通过同步辐射扩展X射线吸收精细结构(EXAFS)研究了Si对As微观吸附机制的影响,表明Si的存在不会影响As在TiO_2上的吸附构型.衰减全反射傅里叶变换红外光谱(ATR-FTIR)原位研究表明Si在TiO_2表面形成Si单体、低聚体和多聚体,从而竞争As的吸附位点,同时增加TiO_2再生的难度.为了实现TiO_2材料的高效再生,本研究进一步考察了氟化钠(NaF)对TiO_2表面Si的脱附效果,发现NaF可以有效地洗脱Si,再生后的TiO_2吸附性能稳定.ATR-FTIR光谱原位分析发现,NaF的加入可有效脱附TiO_2表面的Si单体和多聚体.当利用NaF和Na OH共同洗脱TiO_2表面的As和Si时,3次循环中As的脱附率为86.8%~100.3%,Si的脱附率为67.9%~82.0%.本研究为地下水砷硅共吸附材料的再生提供了一种有效方法.