活性污泥与生物膜复合工艺处理石化废水的研究

实验研究了活性污泥与生物膜复合工艺(HP)对石化废水的处理效果,并与活性污泥工艺(ASP)进行对比研究.结果表明,HP对石化废水中COD的去除效果略好于ASP,而对NH3-N的去除效果明显优于ASP.另外,两种工艺对硫化物和油的去除效果类似.提高进水负荷时,HP表现出较强的耐冲击负荷能力.以2L/h连续运行时,石化废水...     

沸石负载Fe_3O_4光催化氧化去除水中苯酚

为了对水中苯酚的去除进行研究,通过离子交换法及液相沉积法在天然沸石上负载Fe3O4制备出一种具有较高反应活性的复合催化剂,采用X-射线衍射仪(XRD)、扫描电镜(SEM)等仪器对其结构和形貌进行表征,并利用复合催化剂进行非均相UV/Fenton反应处理模拟苯酚废水,考察不同因素对苯酚降解效果的影响。实验结果表明,在催化剂投加量为0.4 g/L,H2O2投加量为二分之一理论投加量,pH为3~10且室温的条件下,处理100 mg/L的模拟苯酚废水,60 min之内苯酚去除率可达90%以上。通过对催化剂的稳定性研究,发现经5次循环使用后,苯酚去除率均可保持在90%以上,具有良好的循环使用性能。     

高压电弧放电处理偶氮染料废水

用高压电弧放电产生的低温等离子体对含偶氮染料的废水进行了处理,以甲基橙为例研究了电压幅值、处理时间、溶液初始浓度、溶液初始pH值、投加Fe^2＋和Fe^3＋对染料脱色的影响。实验结果表明,甲基橙浓度为50mg／L时其降解率随时间和电压幅值的增加而增加。溶液初始浓度对染料去除效果影响较为明显,同等条件下初始浓度越低降解率越高。酸性条件下有利于低温等离子体处理甲基橙。Fe^2＋和Fe^3＋对低温等离子体降解甲基橙有一定的催化作用。电压8kV处理3min,Fe^2＋为20mg／L时去除率由89．64％增至99．72％。Fe2（SO4）,的最佳投加量为5mg／L（以Fe^3＋计）,而FeCl,的最佳投加量为80mg／L（以Fe^3＋计）。     

高浓度钻井废水的混凝-催化氧化处理

以华北油田某深井的高浓度钻井废水(COD高达14 460.0 mg/L)为研究对象,提出了酸化-混凝-催化氧化-吸附的组合处理工艺。重点研制了钻井废水催化氧化处理催化剂(镍基催化剂),通过实验确定了最佳工艺参数条件。着重考察了催化氧化处理的工艺条件,在pH值为4,次氯酸钙投加量为4.4 g/L,催化剂投加量为1.6 g/L的条件下COD降至403.5 mg/L,进一步吸附处理后COD降至139.9 mg/L、色度为30倍、石油类含量为3.8 mg/L、pH为8.0和SS浓度为52mg/L,最终出水水质达到《污水综合排放标准》(GB 8978-1996)二级标准,处理成本为84.8元/m3。     

CuO / 过硫酸氢钾体系催化氧化苯酚简

本论文通过直接沉淀法制备了CuO催化剂,结合过硫酸氢钾,在常温常压下催化氧化处理苯酚模拟废水。采用电子显微镜（SEM）、X射线粉末衍射（XRD）对催化剂进行了表征,并研究了反应过程中各影响因素对降解效率的影响。实验结果表明,在催化剂用量为0.2 g/L,氧化剂浓度为0.25 g/L,pH值为7,反应时间为60 min的条件下,浓度为50 mg/L的苯酚降解率可达100%,TOC去除率达84%。进一步实验表明,催化剂具有良好的重复使用能力。最后,通过自由基捕捉实验,考察了体系中的自由基种类,并根据实验结果,讨论了CuO/过硫酸氢钾体系的催化降解机理。     

一株苯酚降解菌的筛选及降解动力学特性

利用富集驯化的培养方法,从首钢焦化厂废水处理系统中的二沉池出水中,分离筛选出一株能够高效降解苯酚的菌株B3对其16S rDNA序列进行分析,并选择Monod方程和Andrews方程分别研究该菌在不同苯酚浓度条件下的降酚动力学模式。结果表明,B3为蜡状芽孢杆菌(Bacillus cereus);苯酚浓度较低时,苯酚对菌株的生长基本不产生抑制作用,用Monod模型对B3降酚动力学过程进行拟合,其动力学参数V max=0.03 h-1,K s=25.53 mg/L;苯酚浓度较高时,按照Andrews模型对B3降酚动力学过程进行非线性最小二乘曲线拟合,其动力学参数V max=0.08 h-1,K s=147.52 mg/L,K i=384.96 mg/L。根据动力学方程,推论菌株B3降解对于浓度238.30 mg/L的苯酚具有最佳降解效果。     

粉煤灰负载铁离子催化氧化活性黄染料废水

以粉煤灰为载体,制备铁/粉煤灰负载型催化剂,并利用该催化剂催化H2O2氧化降解活性黄染料废水,探讨了H2O2投加量、催化剂投加量、染料初始浓度和初始pH值等因素对染料废水COD去除率和脱色率的影响。结果表明,当染料废水COD初始浓度为200 mg/L,初始pH值为1.7,投加0.5 g/100 mL催化剂及加入1.0 mL浓度为1.13 mol/L的H2O2溶液时,处理效果最好,此时染料废水的COD去除率和脱色率分别达到63%和99%,并且废水的可生化性得到很大的提高。利用该负载催化剂能够有效地减少活性黄染料废水中Fe3+的残留量。     

固定化小球藻与活性污泥的共生系统处理含锌废水

研究固定化小球藻与活性污泥的共生系统对含锌废水中Zn2+的去除效果,分析菌藻状态、初始Zn2+浓度、pH、固定化菌藻小球投加量和菌藻体积比等5个因素对固定化菌藻共生系统去除Zn2+的影响。结果表明,固定化活性污泥、固定化小球藻和固定化菌藻对Zn2+的去除效果均优于悬浮小球藻,其中固定化菌藻对Zn2+的去除效果最好;废水中初始Zn2+浓度小于100 mg/L时,固定化菌藻系统对废水中Zn2+的去除率达到90.5%;固定化菌藻系统去除废水中Zn2+的最佳条件是:初始Zn2+浓度为80 mg/L,pH=7,固定化小球投加量为80 mL,菌藻体积比为1∶2。     

The use of artificial neural network (ANN) for the prediction and simulation of oil degradation in wastewater by AOP

The application of advanced oxidation process (AOP) in the treatment of wastewater contaminated with oil was investigated in this study. The AOP investigated is the homogeneous photo-Fenton (UV/H₂O₂/Fe⁺²) process. The reaction is influenced by the input concentration of hydrogen peroxide H₂O₂, amount of the iron catalyst Fe⁺², pH, temperature, irradiation time, and concentration of oil in the wastewater. The removal efficiency for the used system at the optimal operational parameters (H₂O₂?=?400 mg/L, Fe⁺²?=?40 mg/L, pH?=?3, irradiation time?=?150 min, and temperature?=?30 °C) for 1,000 mg/L oil load was found to be 72 %. The study examined the implementation of artificial neural network (ANN) for the prediction and simulation of oil degradation in aqueous solution by photo-Fenton process. The multilayered feed-forward networks were trained by using a backpropagation algorithm; a three-layer network with 22 neurons in the hidden layer gave optimal results. The results show that the ANN model can predict the experimental results with high correlation coefficient (R ²?=?0.9949). The sensitivity analysis showed that all studied variables (H₂O₂, Fe⁺², pH, irradiation time, temperature, and oil concentration) have strong effect on the oil degradation. The pH was found to be the most influential parameter with relative importance of 20.6 %.     

Titania-supported silver-based bimetallic nanoparticles as photocatalysts

Photocatalytic process has shown recently a great potential as an environmental friendly and clean remediation technology for organic pollutants in wastewater. This work described the synthesis of silver-based bimetallic nanoparticles using colloid chemistry and the subsequent immobilization onto titania to form composite photocatalytic materials (titania-supported Ag–Pt nanoparticles). The photocatalysts were characterized by X-ray diffraction, electron microscopy, and nitrogen physisorption. The catalytic activity of the photocatalysts was evaluated by photocatalytic degradation of phenol and 2-chlorophenol (2-CP) in synthetic wastewater solutions. The photocatalytic processes were conducted in a batch photoreactor containing appropriate solutions of phenol and 2-CP with UV irradiation of 450 W. UV-visible spectrophotometer was used for analyzing the concentration of phenol and 2-CP in solutions. Parameters affecting the photocatalytic process such as the solution pH, phenol and 2-CP concentrations, and catalyst concentration were investigated. The results obtained revealed that TiO₂-supported Ag/Pt nanoparticles showed a higher activity for UV-photocatalytic degradation of both phenol and 2-CP pollutants in the solution (as compared to the plain rutile TiO₂). The photodegradation processes were optimized by the 0.5-g/L catalyst with a pollutant concentration of 50 mg/L for all the samples. Complete degradation for both phenol and 2-CP was achieved after 120 min.     

Temperature-responsive graphene oxide/N-isopropylacrylamide/2-allylphenol nanocomposite for the removal of phenol and 2,4-dichlorophenol from aqueous solution

In this study, a novel thermo-responsive polymer was synthesized with efficient grafting of N-isopropylacrylamide as a thermosensitive polymer onto the graphene oxide surface for the efficient removal of phenol and 2,4-dichlorophenol from aqueous solutions. The synthesized polymer was conjugated with 2-allylphenol. Phenol and 2,4-dichlorophenol were monitored by ultra-performance liquid chromatography system equipped with a photodiode array detector. The nanoadsorbent was characterized by different techniques. The nanoadsorbent revealed high adsorption capacity where the removal percentages of 91 and 99% were found under optimal conditions for phenol and 2,4-dichlorophenol, respectively (for phenol; adsorbent dosage = 0.005 g, pH = 8, temperature= 25 °C, contact time = 60 min; for 2,4-dichlorophenol; adsorbent dosage = 0.005 g, pH = 5, temperature = 25 °C, contact time = 10 min). Adsorption of phenol and 2,4-dichlorophenol onto nanoadsorbent followed pseudo-second-order kinetic and Langmuir isotherm models, respectively. The values of ΔG (average value = ? 11.39 kJ mol^?1 for phenol and 13.42 kJ mol^?1 for 2,4-dichlorophenol), ΔH (? 431.72 J mol^?1 for phenol and ? 15,721.8 J mol^?1 for 2,4-dichlorophenol), and ΔS (35.39 J mol^?1 K^?1 for phenol and ? 7.40 J mol^?1 K^?1 for 2,4-dichlorophenol) confirmed spontaneous and exothermic adsorption. The reusability study indicated that the adsorbent can be reused in the wastewater treatment application. Thermosensitive nanoadsorbent could be used as a low-cost and efficient sorbent for phenol and 2,4-dichlorophenol removal from wastewater samples.

     

活性焦吸附处理一硝基甲苯(MNT)废水

一硝基甲苯(MNT)废水是一种具有高毒性、难降解的火炸药废水。以活性焦为吸附剂,研究了活性焦对MNT废水中COD的吸附性能及pH、时间、温度和活性焦用量对吸附效果的影响,并分析了吸附前后MNT废水水质和急性毒性的变化。实验结果表明,pH、时间和活性焦用量是影响吸附效果的主要因素,吸附过程符合拟二级动力学,吸附速率常数为1.01×10-2g/(mg·min),可以用Freundlich吸附等温线来描述,等温线常数为Kf=1.14×10-4,n=0.58;在pH为3,温度为20℃,活性焦用量为80g/L的条件下吸附MNT废水3 h,COD的去除率达到72.0%,急性毒性下降了98.6%,表明活性焦能有效地吸附处理MNT废水。     

微波诱导AC/Cu、AC/Fe催化非均相Fenton 反应催化降解垃圾渗滤液

采用活性炭载体负载Cu、Fe为催化剂,在微波诱导作用下,对垃圾渗滤液污染物进行降解。实验结果表明,活性炭负载金属前经适当浓度硝酸浸泡处理后,催化剂对COD去除率提高可超过15%,过高硝酸盐浓度对COD去除有不利影响;催化剂对COD去除率随Cu、Fe金属负载量增加呈先增加后降低的趋势,催化剂对Cu、Fe的最佳负载量分别为质量百分比2.11%和1.12%。对于AC-Cu体系,在初始pH=3,H2O2投加量为4.98×103mg/L,催化剂用量为5.0×103mg/L,420 W功率下微波辐射10 min时,垃圾渗滤液COD去除率可达到84.13%;对于AC-Fe体系,当H2O2投加量为0.33×103mg/L,催化剂AC-Fe用量为2.0×104mg/L,420 W功率下微波作用10 min时,垃圾渗滤液COD去除率为60.16%。分析2种催化剂对COD去除差异的原因,可能是催化剂AC-Cu表面单分子分布的阈值比AC-Fe高。降解液的pH值对AC-Cu体系、AC-Fe体系COD去除影响存在拐点,最高COD去除率点对应的降解液pH值为3。微波辐射功率较低时,体系COD去除率随辐射功率增加而增加;辐射功率较高时,高温下垃圾渗滤液中有机硫化物分解成小分子硫化物,对催化剂活性存在一定抑制作用。     

Biodegradation of Chlorimuron-ethyl by the Bacterium Klebsiella jilinsis 2N3

Enrichment culturing of sludge taken from an industrial wastewater treatment pond led to the identification of a bacterium (Klebsiella jilinsis H. Zhang) that degrades chlorimuron-ethyl with high efficiency. Klebsiella jilinsis strain 2N3 grows with chlorimuron-ethyl as the sole nitrogen source at the optimal temperature range of 30–35°C and pH values between 6.0–7.0. In liquid medium, the degradation activity was further induced by chlorimuron-ethyl. Degradation rates followed the pesticide degradation kinetic equation at concentrations between 20 and 200 mg L^?1. Using initial concentrations of 20 and 100 mg L^?1, the degradation rates of chlorimuron-ethyl were 83.5 % and 92.5 % in 12 hours, respectively. At an initial concentration higher than 200 mg L^?1, the degradation rate decreased slightly as the concentration increased. The 2N3 strain also degraded the sulfonylurea herbicides ethametsulfuron, metsulfuron-methyl, nicosulfuron, rimsulfuron, and tribenuron-methyl. This study provides scientific evidence and support for the application of K. jilinsis in bioremediation to reduce environmental pollution.     

活性炭-微波辐照处理丁腈胶乳生产废水的研究

以活性炭-微波辐照工艺处理丁腈胶乳生产废水,考察了催化剂的种类及用量、废水初始浓度、废水初始pH值、微波辐照时间和微波功率等对废水COD去除率的影响.结果表明,采用3 g粉末活性炭处理100 mL COD浓度为3500 mg/L左右的丁腈胶乳废水,在微波辐照功率为200 W,辐照时间4 min的条件下,废水COD去除率最高可达96.6%.动力学研究表明,在最佳操作条件下的反应表观过程近似符合一级反应规律,动力学方程为In(C0/C)=0.6034t 0.9247(R=0.9926),反应速率常数k=0.6034 min-1,半衰期t1/2=1.15 min.     

The Effects of Magnesium and Ammonium Additions on Phosphate Recovery from Greenhouse Wastewater

Phosphorus recovery from greenhouse wastewater, using precipitation-crystallization, was conducted under three levels of calcium concentration, 304 mg/L (7.6 mmol/L), 384 mg/L (9.6 mmol/L), and 480 mg/L (12 mmol/L), and also with additions of ammonium and magnesium into the wastewater. Jar test results confirmed high phosphate removal, with more than 90% of the removal achieved with a pH as low as 7.7. Under the low calcium concentration, ammonium addition affected the chemical reactions at pH lower than 8.0, where struvite was produced; when the pH was raised to 8.8, other calcium compounds dominated the precipitation. Under the medium calcium concentration, ammonium and magnesium addition helped struvite precipitation in the low pH range. Hydroxyapatite (HAP) was the main product. Under the high calcium concentration, ammonium addition showed no effects on the precipitation.     

SBR处理高浓度养猪废水工艺条件

以养猪场废水作为研究对象,采用序列间歇式活性污泥法SBR,通过实验研究了供气量、pH、排泥量、原水稀释倍数、水力停留时间（HRT）对SBR出水水质的影响。结果表明,供气量为375 L/（min·m³）、pH为8.0,并添加排泥100 mL的操作,可使SBR处理效果明显提高,COD、磷和凯氏氮去除率最高分别可达96.37%、94.14%、99.38%。逐步降低进水稀释倍数有利于培养出处理高浓度有机养猪废水的活性污泥,可将平均COD、磷和凯氏氮含量高达9 161.24、33.41和1 502.77 mg/L的养猪废水处理至出水的490.11、5.35和17.84 mg/L。降低HRT对SBR去除率影响不大。     

O3氧化工艺处理黄连素制药废水研究

采用臭氧（O3）氧化法处理含高浓度黄连素和COD的制药废水,探讨了废水初始pH、O3投加量及初始黄连素浓度等因素对O3氧化过程的影响,确定了O3氧化技术处理黄连素制药废水的最佳操作条件。结果表明,O3能够有效分解废水中的黄连素,降低其COD浓度;黄连素浓度为700mg／L、COD为3500mg／L、pH为0．88的废水,进气O3浓度为14．05mg／（L·min）,处理时间为180rain（即投加量为2529mg／L）时,黄连素和COD的降解率分别可达77．46％和41．28％,BOD,／COD比（B／C比）从0．06提高到0．34,增加了4．7倍;随着废水中初始黄连素浓度的升高,废水COD降解率逐渐降低。O3氧化法是一种有效的黄连素制药废水预处理技术,可以大大提高废水的可生化性。     

Preparation of activated carbon from dried pods of Prosopis cineraria with zinc chloride activation for the removal of phenol

Utilization of agrowaste materials for the production of activated carbon, as an excellent adsorbent with large surface area, is well established industrially, for dephenolation of wastewater. In the present work, dried pods of Prosopis cineraria—a novel and low-cost agrowaste material—were used to prepare activated carbons by zinc chloride activation. Batch adsorption experiments were carried out to study the effects of various physicochemical parameters such as initial phenol concentration, adsorbent dose, initial solution pH, and temperature. Pseudo-first-order second-order and diffusion kinetic models were used to identify the possible mechanisms of such adsorption process. The Langmuir and Freundlich equations were used to analyze the adsorption equilibrium. Maximum removal efficiency of 86 % was obtained with 25 mg?L^?1 of initial phenol concentration. The favorable pH for maximum phenol adsorption was 4.0. Freundlich equation represented the adsorption equilibrium data more ideally than the Langmuir. The maximum adsorption capacity obtained was 78.32 mg?g^?1 at a temperature of 30 °C and 25 mg?L^?1 initial phenol concentration. The adsorption was spontaneous and endothermic. The pseudo-second-order model, an indication of chemisorption mechanism, fitted the experimental data better than the pseudo-first-order Lagergren model. Regeneration of spent activated carbon was carried out using Pseudomonas putida MTCC 2252 as the phenol-degrading microorganism. Maximum regeneration up to 57.5 % was recorded, when loaded phenol concentration was 25 mg?L^?1. The data obtained in this study would be useful in designing and fabricating an efficient treatment plant for phenol-rich effluents.     

Fe (III) supported on resin as effective catalyst for the heterogeneous oxidation of phenol in aqueous solution

FeIII supported on resin as an effective catalyst for oxidation was prepared and applied for the degradation of aqueous phenol. Phenol was selected as a model pollutant and the catalytic oxidation was carried out in a batch reactor using hydrogen peroxide as the oxidant. The influent factors on oxidation, such as catalyst dosage, H2O2 concentration, pH, and phenol concentration were examined by considering both phenol conversion and chemical oxygen demand (COD) removal. The FeIII-resin catalyst possesses a high oxidation activity for phenol degradation in aqueous solution. The experimental results of this study show that almost 100% phenol conversion and over 80% COD removal can be achieved with the FeIII-resin catalyst catalytic oxidation system. A series of prepared resin were investigated for improving the oxidation efficiency. It was found that the reaction temperature and initial pH in solution significantly affected both of phenol conversion and COD removal efficiency. The activity of the catalyst significantly decreased at high pH, which was similar to the Fenton-like reaction mechanism. Results in this study indicate that the FeIII-resin catalytic oxidation process is an efficient method for the treatment of phenolic wastewater.