Total and Methylmercury in Soft Tissues of White-Tailed Eagle (Haliaeetus albicilla) and Osprey (Pandion haliaetus) Collected in Poland

Mercury (Hg) contamination in piscivorous birds, especially methylmercury (MeHg), has been drawing much attention worldwide in regard to its bioaccumulation and biomagnification in food chains. In this study on Hg in the soft tissues of white-tailed eagles (n = 22) and ospreys (n = 2) from Poland, total Hg (THg) range was 0.15–47.6 while MeHg range was 0.11–8.05 mg kg⁻¹ dry weight. In both species, median THg and MeHg concentrations were lower in the muscle and brain than in the liver and kidney. Median nephric residues were just under 3 and 5 mgTHg kg⁻¹ or 0.9 and 3.7 mgMeHg kg⁻¹ for white-tailed eagle and osprey, respectively. In Norwegian data from the 1970s and in our results, MeHg in the muscle of white-tailed eagle was ~60 % THg (%MeHg = MeHg/THg × 100), lower than in other piscivorous birds. A clear similarity in THg tissue levels was found between Polish and German populations of white-tailed eagles.     

Effect of Advanced Oxidants Generated Via Ultraviolet Light on a Sequentially Loaded and Regenerated Granular Activated Carbon Biofilter

Abstract

The objective of this research was to investigate a sequentially loaded and regenerated granular activated carbon (GAC) biofilter system and to determine whether regenerative ozonation/advanced oxidation could improve the removal and biodegradation of a volatile organic compound from a contaminated airstream. Bench-scale reactors were constructed to operate in a manner analogous to a commercially available system manufactured by Terr-Aqua Environmental Systems (only with longer contact time). The GAC system consisted of two GAC biofilter beds that operated in a cyclical manner. On a given day, the first GAC bed adsorbed methyl isobutyl ketone from a simulated waste airstream, while the second bed underwent regeneration; then on the next day, the second bed was in the adsorption mode while the first was regenerated.

Three bench-scale systems were used to compare the performance under three operating conditions: (1) ozone/ associated oxidant regeneration of a GAC biofilter system that was seeded with microorganisms from a field site, (2) a humid air regeneration of a seeded GAC biofilter, and (3) a humid air regeneration of an unseeded GAC biofilter. For the advanced oxidant regenerated GAC biofilter, a maximum removal efficiency of >95% was achieved with an empty bed contact time of 148 sec and an influent concentration of 125 ppm methyl isobutyl ketone, and 90–95% was achieved at 148-sec empty bed contact time and a 1150-ppm influent.     

Effect of advanced oxidants generated via ultraviolet light on a sequentially loaded and regenerated granular activated carbon biofilter

The objective of this research was to investigate a sequentially loaded and regenerated granular activated carbon (GAC) biofilter system and to determine whether regenerative ozonation/advanced oxidation could improve the removal and biodegradation of a volatile organic compound from a contaminated airstream. Bench-scale reactors were constructed to operate in a manner analogous to a commercially available system manufactured by Terr-Aqua Environmental Systems (only with longer contact time). The GAC system consisted of two GAC biofilter beds that operated in a cyclical manner. On a given day, the first GAC bed adsorbed methyl isobutyl ketone from a simulated waste airstream, while the second bed underwent regeneration; then on the next day, the second bed was in the adsorption mode while the first was regenerated. Three bench-scale systems were used to compare the performance under three operating conditions: (1) ozone/ associated oxidant regeneration of a GAC biofilter system that was seeded with microorganisms from a field site, (2) a humid air regeneration of a seeded GAC biofilter, and (3) a humid air regeneration of an unseeded GAC biofilter. For the advanced oxidant regenerated GAC biofilter, a maximum removal efficiency of >95% was achieved with an empty bed contact time of 148 sec and an influent concentration of 125 ppm methyl isobutyl ketone, and 90-95% was achieved at 148-sec empty bed contact time and a 1150-ppm influent.     

A simple model which predicts some non-linear features between atmospheric sulphur and sulphur emissions

This paper develops a simple model and suggests a plausible chemico-physical mechanism for a non-linear response between atmospheric sulphur and sulphur emissions. It contains simplified representations of transport, deposition and conversion processes and uses a proxy in-cloud oxidant-limited reaction along a pathway connecting an emission source with a receptor site. Individual pathway responses to emissions show linear behaviour above a threshold. However, by averaging the values of SO2 at the receptor site from different pathways a continuous non-linear relationship is obtained. As emissions reduce, distant emission sources become less significant contributors of sulphur dioxide at a receptor site but their emissions are still counted in an emission inventory, leading to an apparent non-linearity. Sulphate is always found to contribute a signal to the receptor site total. This model goes someway to explaining a proposed 'crossover' between observed proportions of wet and dry deposited sulphur in the UK as emissions have been reduced.     

The current state of knowledge of ecosystems and ecosystem services in Russia: A status report

This paper focusses on a conceptual overview of ways to address a comprehensive analysis of ecosystem services (ES) in a country as large and heterogeneous as Russia. As a first step, a methodology for assessing the services for the federal subjects of Russia was chosen, i.e., its constituent provinces and similar entities, in physical terms. Russia harbors a great diversity of natural conditions and ecosystems which are suppliers of ES, and likewise a variety of the socio-economic conditions that shape the demand for these services and their consumption. The methodological approach described permits several important tasks to be addressed: the evaluation of the degree of satisfaction of people’s needs for ES, the identification of ecological donor and acceptor regions, and zoning of the country’s territory for ES assessment. The next step is to prepare a prototype of a National Report on ES in Russia, for which we are presenting the planned structure.     

Humans and Ecosystems Over the Coming Millennia: Overview of a Biosphere Assessment of Radioactive Waste Disposal in Sweden

This is an overview of the strategy used to describe the effects of a potential release from a radioactive waste repository on human exposure and future environments. It introduces a special issue of AMBIO, in which 13 articles show ways of understanding and characterizing the future. The study relies mainly on research performed in the context of a recent safety report concerning a repository for spent nuclear fuel in Sweden (the so-called SR-Site project). The development of a good understanding of on-site processes and acquisition of site-specific data facilitated the development of new approaches for assessment of surface ecosystems. A systematic and scientifically coherent methodology utilizes the understanding of the current spatial and temporal dynamics as an analog for future conditions. We conclude that future ecosystem can be inferred from a few variables and that this multidisciplinary approach is relevant in a much wider context than radioactive waste.     

Numerical Modeling of the Transport Diffusion and Deposition of Pollutants For Regions and Extended Scales

There is an emerging need to develop understanding and predictive capability for the transport, diffusion, and deposition of pollutants on regional and extended spatial scales. Some recent developments in the numerical simulation of pollutant transport and diffusion are reviewed and summarized herein, including case studies of model validation whenever’available. The efforts reported include: (a) the development and verification of a Lagrangian large-cloud diffusion code for intermediate to extended scales; (b) a hybrid Lagrangian-Eulerian transport-diffusion code for simulating pollutant distributions in transient stratified shear flow; (c) a meteorological submodel for determining a mass-consistent wind field on a regional scale suitable as input to a regional air pollution model; and (d) the development and initial verification of a multi-box regional air pollution model for the San Francisco Bay Area utilizing a mass-consistent wind field submodel.     

Concurrent 2,4-D and triclopyr biomonitoring of backpack applicators, mixer/loader and field supervisor in forestry

Two herbicides, 2,4-D and triclopyr esters (application ratio 1.6:1 acid equivalents) were applied as a tank mix by a crew of 8 backpack sprayer applicators, a mixer/loader, and a field supervisor. The crew was employed in a conifer release program in northern California during the summer of 2002. Biomonitoring (urine, 24 h) utilized 2,4-D and triclopyr (a.e.) as rapidly excreted exposure biomarkers. The absorbed dosages of 2,4-D and triclopyr were calculated based upon cotton whole body suits and biomonitoring. Dosages based upon accumulation of the herbicides on body suits averaged 42.6 μg (a.e.) 2,4-D/kg-d and 8.0 μg (a.e.) triclopyr/kg-d. Six consecutive days of concurrent urine collections showed that backpack applicators excreted an average of 11.0 μg (a.e.) 2,4-D/kg-d and 18.9 μg (a.e.) triclopyr/kg-d. Estimates based upon curve fitting were 17.1 and 29.3 μg (a.e.)/kg-d, respectively. Results suggest that passive dosimetry for 2,4-D consistently overestimated the dosage measured using biomonitoring by a factor of 2-3 fold, while for triclopyr, passive dosimetry underestimated the absorbed dose based on biomonitoring by a factor of 2-4 fold.     

Formulation of a soil-pesticide transport model based on a compartmental approach

A semianalytical soil-pesticide transport model is formulated based on a compartmental approach to determine spatial and temporal variations of pesticide residues across a soil profile. The compartmental model is implemented by drawing an analogy between a series of continuous-flow stirred tank reactors and a soil horizon that consists of multiple perfectly mixed compartments. The analogy is strengthened by exploiting a relation between the compartment series and the conventional convective-dispersive equation (CDE) for vertical transport in the soil. Consequently, the number of compartments in the model formulation is not free, but dictated as a function of transport parameters. The model formulation allows consideration of arbitrary boundary value specifications and also, for some cases, spatially varying initial concentration profiles. Sorption kinetics is represented via a two-site model that involves a linear sorption isotherm and a first-order irreversible sorption or a radial diffusive penetrating model. For these three cases, analysis of the compartmental model allows the resultant concentration profiles to be expressed in terms of the Poisson distribution. When a nonlinear kinetic sorption model is used to simulate the sorption processes, an analytical solution is not found and a numerical approach is required.     

Results of Field Measurements of Industrial Particulate Sources and Electrostatic Precipitator Performance

This paper presents results of source size distribution measurements over the size range from 0.1 μm to 5 μm for six classes of particulate sources and fractional efficiency measurements on five full scale electrostatic precipitators and one pilot scale precipitator. The precipitators all showed moderately high to high particulate collection efficiencies for particles having diameters larger than a few micrometers or smaller than a few hundredths of a micrometer and a minimum in collection efficiency for particles having diameters of a few tenths of a micrometer.     

The effect of emissions of fertilizer production on the environment contamination by cadmium and arsenic in southern Brazil

The distribution of cadmium and arsenic in rainwater, surface soil and groundwater in a zone of influence of emissions of a phosphate fertilizer factory has been investigated. The analysis of rainwater along a wind line shows that cadmium in the soluble form precipitates close to emission source, whereas arsenic migrates further and also in the soluble form precipitates at a greater distance. The pH controls the distribution of cadmium and arsenic in rain and groundwater. Concentration of soluble cadmium along the impact line increases with reduction of pH and arsenic, contrary to the increase of pH. Concentrations of cadmium and arsenic in surface soil correlate well among themselves near to emission point. In a zone of confluence of emissions with sea air at a distance from the factory there is sedimentation of arsenic on a geochemical barrier and formation of a separate anomaly in soil.     

Sustainable development and the worldwide market economy: a necessary but difficult reconciliation

The only satisfactory concept of development is a global one, of which the usual notion of sustainable development is only a part. The only economic system providing efficiency is the market, with a high level of responsibility given to decentralised and autonomous decision-makers. However, the market economy does not automatically generate globally desirable development. It has to be complemented by public intervention, leading in a single country to a mixed economy, and in a world-set of countries to international agreements, creating two kinds of international order, at two levels: very restrictive between countries with common basic political and social values, and provisionally more flexible and concerning only few very fundamental topics at a world-wide level.     

Smokeless Stacks—Industry’s Big Problem

There seems to be a general impression on the part of the public and many technical people that dust collecting systems on the open hearth furnace are simply a matter of giving a contract for a duplicate system to that previously installed; signing a check for a sum to cover the cost of the cleaning equipment itself, pressing the start-up button and then sitting back to receive the plaudits of a grateful community. This paper will briefly present some of the problems common to all of the installations to date. It will also explain why the cost of the cleaning equipment itself is such a small portion of the total cost.     

Development of cleaner-burning brick kilns in Ciudad Juarez, Chihuahua, Mexico

The following results provide a comparison between net airborne contamination produced by the traditional form of kiln used in Northern Mexico and by those modified according to a design by Dr. Robert Marquez. What has become known as the MK style kiln was intended to significantly reduce contaminant emissions. The concept involves covering the kiln with a dome and channeling the output of an active kiln through a second, identical loaded kiln for its additional filtration of the effluents. Kilns of a pair are connected via clay brick channels. The roles are reversed after the initial kiln is refilled. Significant reductions in the particulate and gaseous emissions were achieved in the prototype system, but a connectional problem with recent kiln pairs has also limited the degree of operational success. The problem did not mask the potential of the MK kiln, as will be shown. Additional anticipated benefits to the owners of MK kilns, such as reduced operating cycles and decreased quantities of fuel, also have been verified. Key measurements made during all of the burns were of aerosol densities and buoyancies in the flues, kiln temperatures, and, on a number of occasions, chemical analyses of both aerosol and gaseous effluents. Continuous time histories of aerosol densities for most burns (of a total of -40) provide a basis for examining features and the effects of differing styles of operation with respect to burn efficiency and net contaminant masses. Covering the active kiln with a dome produces a net reduction in dry aerosol effluent mass of a factor between 5 and 10, whereas the addition of a filter kiln produces a net reduction of about a factor of 2. The use of used motor oil as a fuel further reduced aerosol contamination by -1 order of magnitude.     

Optimization of the intermittent aeration in a full-scale wastewater treatment plant biological reactor for nitrogen removal.

The optimization of the intermittent aeration in a full-scale biological reactor treating municipal and industrial wastewater has been studied by means of an experimental design, where the main factors considered have been the on-off period of aeration and the dissolved-oxygen set point. The objective of the work has been to determine the optimal configuration of the aeration control to achieve a simultaneous removal of carbon (expressed as chemical oxygen demand [COD]) and nitrogen. The results were obtained in a full-scale bioreactor located at the wastewater treatment plant of Sant Celoni (Barcelona, Spain), where a nitrogen removal based on a nitrification-denitrification process is being tested. It has been shown that the crucial parameter to ensure a complete removal of COD and nitrogen is to give the system a long time of on-off aeration to complete both the nitrification and the denitrification processes, whereas the dissolved-oxygen set point has a minor influence on the overall performance. The results presented can be applied to a great number of similar systems, in which a nitrogen removal, based on a nitrification-denitrification scheme, is currently being tested or implemented.     

Stabilization of APC residues from waste incineration with ferrous sulfate on a semi-industrial scale

A stabilization method for air pollution control (APC) residues from municipal solid waste incineration (MSWI) involving mixing of the residue with water and FeSO4 has been demonstrated on a semi-industrial scale on three types of APC residues: a semidry (SD) APC residue, a fly ash (FA), and an FA mixed with sludge (FAS) from a wet flue gas cleaning system. The process was performed in batches of 165-175 kg residue. It generates a wastewater that is highly saline but has a low content of heavy metals such as Cd, Cr, and Pb. The stabilized and raw residues have been subject to a range of leaching tests: the batch leaching test, the pH-static leaching test, the availability test, and the column test. These tests showed that the stabilized residues have remarkably improved leaching properties, especially with respect to Pb but also with respect to Cd, Cu, and Zn. The release of Pb was reduced by a factor of 250-36,000.     

Effect of diffusion limitation and substrate inhibition on steady states of a biofilm reactor treating a single pollutant

The occurrence of multiple steady states in a toluene biodegrading, diffusion-limited biofilm under aerobic conditions was investigated by computer models: one steady-state, and one nonsteady-state. Two stable and one unstable intermediate steady-state were identified in a narrow set of combinations of parameters values. The nonsteady-state model predicts conditions that evolve to a steady state that is within 0.02–1% of the solution of the steady-state model, depending on the number of grid points used, confirming the algorithms are valid. Multiple steady states occur if, (1) a biofilm is exposed to a constant gas-phase pollution concentration, which exceeds or undershoots a certain threshold, (2) in a narrow range of parameter values and (3) provided that the pollutant degradation follows Haldane kinetics. Such a biofilm displays half-saturation (i.e., Michaelis-Menten)-like apparent (“falsified”) kinetics from a concentration range starting at zero up to the occurrence of a second steady state. Multiple steady states and falsified kinetics can negatively affect a biofilter and the experimental determination of kinetic parameters, respectively.

Implications: The occurrence of multiple steady states in a VOC treating biofilm, shows the significant impact of degradation kinetics and diffusion limitation on the biofilm behavior. Moreover, the implied possible sudden drop of removal efficiency of a biofilter, based on the occurrence of multiple steady states lead to possible bottle-necks in biofilter application and operation.     

Microméthode de dosage simultané de l'alcool isopropylique et de son métabolite l'acétone

Simultaneous determination of Isopropyl Alcohol and Acetone prove to be necessary in cases of poisoning by this widely used alcohol. An aluminum capsule containing a sample of blood to be analyzed is introduced into a gas chromatograph equipped with a flameionization detector and a Carbowax 20 M - Chromosorb WHP column. Use of a small blood sample (0.50 μl) and high sensitivity of the method make it a selected procedure in the clinical diagosis of poisoning by Isopropyl Alcohol.     

Predictive modelling of NAPL injection tests in variable aperture spatially correlated fractures.

In preparation for a field experiment where a NAPL will be injected into a fractured sandstone aquifer, a 2D invasion percolation model of DNAPL migration in a single horizontal fracture with varying aperture has been developed. This simulation investigated the effect of spatially correlated fracture aperture fields on pressure-saturation relationships as a function of variable aperture mean, standard deviation, and spatial correlation statistics under hydrostatic conditions. Results from spatially correlated variable aperture fields can be significantly different from random fields. Longer ranges decreased entry pressures and higher standard deviations decreased nonwetting phase saturations. Mean aperture is the major control on displacement pressure, entry pressure and the form of the pressure-saturation curve. Simulation results using statistical parameters for a variable aperture natural sandstone fracture as described by Yeo et al. [International Journal of Rock Mechanics and Mining Sciences 35 (1998) 1051] closely resemble a Brooks-Corey pressure-saturation function, and exhibit a distinct entry pressure followed by a rapid increase in nonwetting phase saturation. Graphical estimates of entry pressure provide a good approximation of the critical aperture controlling the formation of a continuous nonwetting phase pathway in a variable aperture fracture. Consequently, we show that multiphase flow concepts developed for porous media can successfully be applied to variable aperture fractures. Entry pressure correlates well to the mean aperture in these simulations when using a Gaussian distribution of fracture aperture. Interpreted aperture distributions from NAPL injection experiments do not fit the true distribution well at low nonwetting phase saturations, but do at higher saturations above the entry pressure. Consequently, true, mechanical aperture variation within a fracture plane cannot be determined from NAPL injection experiments either in the field or laboratory.     

Natural phillipsite as a matrix for a slow-release formulation of oxamyl

The performance of phillipsite as a matrix for slow-release formulation of oxamyl [N,N-dimethyl-2-methylcarbamoyl-oxymino-2-(methylthio)acetamide] was tested. The adsorption kinetics followed a first-order law, and the adsorption isotherm fitted well in a two-surface Langmuir model, suggesting a double mechanism of interaction between oxamyl and the sorbent. The sorption mechanism, studied by FTIR, provided two fractions of oxamyl. The first one is sorbed on the mineral surface, linked by H-bonding, and the second one is constituted by a multilayer of oxamyl molecules linked by a water bridge between them. The release kinetics of oxamyl from a substratum zeolite-oxamyl also follows a first-order law, with two stages that correspond to both fractions of oxamyl previously detected.