鼠李糖脂对不同菌株降解柴油污染物的影响

通过一系列实验分析了鼠李糖脂对柴油污染物生物降解的影响。单菌株柴油降解实验结果表明,在添加生物表面活性剂鼠李糖脂后,各菌株细胞表面疏水性均发生不同程度的增加,并且对柴油的降解率均有所提高。在混合菌的柴油污染物降解实验中,发现当向土壤中添加了200 mg/L鼠李糖脂时,对柴油的降解才有较大的提高;而当添加100 mg/L的鼠李糖脂到水体中时,对柴油的降解就有较大的提高,而当鼠李糖脂浓度提高为200 mg/L时,柴油的降解率却没有进一步明显的提高。这说明鼠李糖脂对柴油降解的影响程度不仅与环境介质有关,还与添加的鼠李糖脂浓度有关。进一步分析表明,添加适当浓度的鼠李糖脂不仅可以提高对柴油的降解率,而且可加速其降解速度,缩短生物修复所需时间。     

Biosurfactant technology for remediation of cadmium and lead contaminated soils

This research focuses on column experiments conducted to evaluate the potential of environmentally compatible rhamnolipid biosurfactant produced by Pseudomonas aeruginosa strain BS2 to remove heavy metals (Cd and Pb) from artificially contaminated soil. Results have shown that di-rhamnolipid removes not only the leachable or available fraction of Cd and Pb but also the bound metals as compared to tap water which removed the mobile fraction only. Washing of contaminated soil with tap water revealed that approximately 2.7% of Cd and 9.8% of Pb in contaminated soil was in freely available or weakly bound forms whereas washing with rhamnolipid removed 92% of Cd and 88% of Pb after 36 h of leaching. This indicated that di-rhamnolipid selectively favours mobilization of metals in the order of Cd>Pb. Biosurfactant specificity observed towards specific metal will help in preferential elution of specific contaminant using di-rhamnolipid. It was further observed that pH of the leachates collected from heavy metal contaminated soil column treated with di-rhamnolipid solution was low (6.60-6.78) as compared to that of leachates from heavy metal contaminated soil column treated with tap water (pH 6.90-7.25), which showed high dissolution of metal species from the contaminated soil and effective leaching of metals with treatment with biosurfactant. The microbial population of the contaminated soil was increased after removal of metals by biosurfactant indicating the decrease of toxicity of metals to soil microflora. This study shows that biosurfactant technology can be an effective and nondestructive method for bioremediation of cadmium and lead contaminated soil.     

Evaluation of B. subtilis SPB1 biosurfactants' potency for diesel-contaminated soil washing: optimization of oil desorption using Taguchi design

Low solubility of certain hydrophobic soil contaminants limits remediation process. Surface-active compounds can improve the solubility and removal of hydrophobic compounds from contaminated soils and, consequently, their biodegradation. Hence, this paper aims to study desorption efficiency of oil from soil of SPB1 lipopeptide biosurfactant. The effect of different physicochemical parameters on desorption potency was assessed. Taguchi experimental design method was applied in order to enhance the desorption capacity and establish the best washing parameters. Mobilization potency was compared to those of chemical surfactants under the newly defined conditions. Better desorption capacity was obtained using 0.1 % biosurfacatnt solution and the mobilization potency shows great tolerance to acidic and alkaline pH values and salinity. Results show an optimum value of oil removal from diesel-contaminated soil of about 87 %. The optimum washing conditions for surfactant solution volume, biosurfactant concentration, agitation speed, temperature, and time were found to be 12 ml/g of soil, 0.1 % biosurfactant, 200 rpm, 30 °C, and 24 h, respectively. The obtained results were compared to those of SDS and Tween 80 at the optimal conditions described above, and the study reveals an effectiveness of SPB1 biosurfactant comparable to the reported chemical emulsifiers. (1) The obtained findings suggest (a) the competence of Bacillus subtilis biosurfactant in promoting diesel desorption from soil towards chemical surfactants and (b) the applicability of this method in decontaminating crude oil-contaminated soil and, therefore, improving bioavailability of hydrophobic compounds. (2) The obtained findings also suggest the adequacy of Taguchi design in promoting process efficiency. Our findings suggest that preoptimized desorption process using microbial-derived emulsifier can contribute significantly to enhancement of hydrophobic pollutants' bioavailability. This study can be complemented with the investigation of potential role in improving the biodegradation of the diesel adsorbed to the soil.     

Evaluation of biosurfactants for crude oil contaminated soil washing

An evaluation of the ability of aqueous biosurfactant solutions (aescin, lecithin, rhamnolipid, saponin and tannin) for possible applications in washing crude oil contaminated soil was carried out. The biosurfactants behaviour in soil-water, water-oil and oil-soil systems (such as foaming, solubilization, sorption to soil, emulsification, surface and interfacial tension) was measured and compared with a well-known chemical surfactant (sodium dodecyl sulphate, SDS) at varying concentrations. Results showed that the biosurfactants were able to remove significant amount of crude oil from the contaminated soil at different solution concentrations for instance rhamnolipid and SDS removed up to 80% oil and lecithin about 42%. The performance of water alone in crude oil removal was equally as good as those of the other biosurfactants. Oil removal was due to mobilization, caused by the reduction of surface and interfacial tensions. Solubilization and emulsification effects in oil removal were negligible due to the low crude oil solubilization of 0.11%. Therefore, these studies suggest that knowledge of surfactants' behaviour across different systems is paramount before their use in the practical application of oil removal.     

Characterization of hydrocarbon-degrading and biosurfactant-producing Pseudomonas sp. P-1 strain as a potential tool for bioremediation of petroleum-contaminated soil

The Pseudomonas sp. P-1 strain, isolated from heavily petroleum hydrocarbon-contaminated soil, was investigated for its capability to degrade hydrocarbons and produce a biosurfactant. The strain degraded crude oil, fractions A5 and P3 of crude oil, and hexadecane (27, 39, 27 and 13 % of hydrocarbons added to culture medium were degraded, respectively) but had no ability to degrade phenanthrene. Additionally, the presence of gene-encoding enzymes responsible for the degradation of alkanes and naphthalene in the genome of the P-1 strain was reported. Positive results of blood agar and methylene blue agar tests, as well as the presence of gene rhl, involved in the biosynthesis of rhamnolipid, confirmed the ability of P-1 for synthesis of glycolipid biosurfactant. ¹H and ¹³C nuclear magnetic resonance, Fourier transform infrared spectrum and mass spectrum analyses indicated that the extracted biosurfactant was affiliated with rhamnolipid. The results of this study indicate that the P-1 and/or biosurfactant produced by this strain have the potential to be used in bioremediation of hydrocarbon-contaminated soils.     

Heavy metal (Cu,Cd, Pb,Cr) washing from river sediment using biosurfactant rhamnolipid

Heavy metal-contaminated sediments posed a serious threat to both human beings and environment. A biosurfactant, rhamnolipid, was employed as the washing agent to remove heavy metals in river sediment. Batch experiments were conducted to test the removal capability. The effects of rhamnolipid concentration, washing time, solution pH, and liquid/solid ratio were investigated. The speciation of heavy metals before and after washing in sediment was also analyzed. Heavy metal washing was favored at high concentration, long washing time, and high pH. In addition, the efficiency of washing was closely related to the original speciation of heavy metals in sediment. Rhamnolipid mainly targeted metals in exchangeable, carbonate-bound or Fe-Mn oxide-bound fractions. Overall, rhamnolipid biosurfactant as a washing agent could effectively remove heavy metals from sediment.

     

A comparison of the efficiency of different surfactants for removal of crude oil from contaminated soils

This paper presents the results from study investigating the efficiency with which different surfactants remove crude oil from contaminated soil using a soil washing process. The surfactants studied were aqueous solutions of rhamnolipid, saponin and sodium dodecyl sulfate (SDS). The efficiency of surfactants' removal was quantified and then GC/MS analysis conducted to investigate the distribution of hydrocarbons remaining on the washed soil samples compared to those on a control. The results showed that SDS removed the most crude oil from soil, followed by rhamnolipid and then saponin. However, the different surfactants showed preferences in terms of which crude oil components they removed from the contaminated soil. SDS removed more of the aliphatics than aromatic hydrocarbons whereas saponin removed the aromatic hydrocarbon preferentially to the aliphatic hydrocarbons. Clearly these results provide important information for the selection of surfactants used to remove crude oil from contaminated soils.     

Crude oil contaminated soil washing in air sparging assisted stirred tank reactor using biosurfactants

This study investigated the removal of crude oil from soil using air sparging assisted stirred tank reactors. Two surfactants (rhamnolipid and sodium dodecyl sulfate, SDS) were tested and the effects of different parameters (i.e. temperature, surfactant concentrations, washing time, volume/mass ratio) were investigated under varying washing modes namely, stirring only, air sparging only and the combination of stirring and air sparging. The results showed that SDS removed more than 80% crude oil from non-weathered soil samples, whilst rhamnolipid showed similar oil removal at the third and fourth levels of the parameters tested. The oil removal ability of the seawater prepared solutions were better than those of the distilled water solutions at the first and second levels of temperature and concentration of surfactant solutions. This approach of soil washing was noted to be effective in reducing the amount of oil in soil. Therefore we suggested that a field scale test be conducted to assess the efficiency of these surfactants.     

Bioremediation and reclamation of soil contaminated with petroleum oil hydrocarbons by exogenously seeded bacterial consortium: a pilot-scale study

Purpose  

Spillage of petroleum hydrocarbons causes significant environmental pollution. Bioremediation is an effective process to remediate petroleum oil contaminant from the ecosystem. The aim of the present study was to reclaim a petroleum oil-contaminated soil which was unsuitable for the cultivation of crop plants by using petroleum oil hydrocarbon-degrading microbial consortium.     

Investigation of the removal of heavy metals from sediments using rhamnolipid in a continuous flow configuration

Heavy metal contamination of sediments is hazardous to benthic organisms and needs more attention in order to prevent entry of these heavy metals into the food chain. Biosurfactants have shown the capability to remove heavy metals from soils and sediments. The objective of this research was to evaluate the performance of rhamnolipid, a glycolipid biosurfactant, in a continuous flow configuration (CFC) for removal of heavy metals (copper, zinc, and nickel) from the sediments taken from Lachine Canal, Canada, to simulate a flow through remediation technique. In this configuration, rhamnolipid solution with a constant rate was passed through the sediment sample within a column. Important parameters such as the concentration of rhamnolipid and the additives, time and the flow rate were investigated. The removal of heavy metals from sediments was up to 37% of Cu, 13% of Zn, and 27% of Ni when rhamnolipid without additives was applied. Adding 1% NaOH to 0.5% rhamnolipid improved the removal of copper by up to 4 times compared with 0.5% rhamnolipid alone. This information is valuable for designing a remediation protocol for sediment washing.     

Efficiency of lipopeptide biosurfactants in removal of petroleum hydrocarbons and heavy metals from contaminated soil

This study describes the potential application of lipopeptide biosurfactants in removal of petroleum hydrocarbons and heavy metals from the soil samples collected from industrial dumping site. High concentrations of heavy metals (like iron, lead, nickel, cadmium, copper, cobalt and zinc) and petroleum hydrocarbons were present in the contaminated soil samples. Lipopeptide biosurfactant, consisting of surfactin and fengycin was obtained from Bacillus subtilis A21. Soil washing with biosurfactant solution removed significant amount of petroleum hydrocarbon (64.5 %) and metals namely cadmium (44.2 %), cobalt (35.4 %), lead (40.3 %), nickel (32.2 %), copper (26.2 %) and zinc (32.07 %). Parameters like surfactant concentration, temperature, agitation condition and pH of the washing solution influenced the pollutant removing ability of biosurfactant mixture. Biosurfactant exhibited substantial hydrocarbon solubility above its critical micelle concentration. During washing, 50 % of biosurfactant was sorbed to the soil particles decreasing effective concentration during washing process. Biosurfactant washed soil exhibited 100 % mustard seed germination contradictory to water washed soil where no germination was observed. The results indicate that the soil washing with mixture of lipopeptide biosurfactants at concentrations above its critical micelle concentration can be an efficient and environment friendly approach for removing pollutants (petroleum hydrocarbon and heavy metals) from contaminated soil.     

Solvent extraction for heavy crude oil removal from contaminated soils

A new strategy of heavy crude oil removal from contaminated soils was studied. The hexane-acetone solvent mixture was used to investigate the ability of solvent extraction technique for cleaning up soils under various extraction conditions. The mixtures of hexane and acetone (25 vol%) were demonstrated to be the most effective in removing petroleum hydrocarbons from contaminated soils and approx 90% of saturates, naphthene aromatics, polar aromatics, and 60% of nC₇-asphaltenes were removed. Kinetic experiments demonstrated that the equilibrium was reached in 5 min and the majority of the oil pollutants were removed within 0.5 min. The effect of the ratio between solvent and soil on the extraction efficiency was also studied and results showed that the efficiency would increase following the higher solvent soil ratio. Then the multistage continuous extraction was considered to enhance the removal efficiency of oil pollutants. Three stages crosscurrent and countercurrent solvent extraction with the solvent soil ratio 6:1 removed 97% oil contaminants from soil. Clearly the results showed that the mixed-solvent of hexane and acetone (25 vol%) with character of low-toxic, acceptable cost and high efficiency was promising in solvent extraction to remove heavy oil fractions as well as petroleum hydrocarbons from contaminated soils.     

Combined UV-biological degradation of PAHs

The UV-photolysis of PAHs was tested in silicone oil and tetradecane. In most cases, the degradation of a pollutant provided within a mixture was lower than when provided alone due to competitive effects. With the exception of anthracene, the larger pollutants (4- and 5-rings) were always degraded first, proving that UV-treatment preferentially acts on large PAHs and thereby provides a good complement to microbial degradation. UV-photolysis was also found to be suitable for treatment of soil extract from contaminated soils. The feasibility of UV-biological treatment was demonstrated for the removal of a mixture of phenanthrene and pyrene in silicone oil. UV-irradiation of the silicone oil led to 83% pyrene removal but no phenanthrene photodegradation. Subsequent treatment of the oil in a two-phases partitioning bioreactor (TPPB) system inoculated with Pseudomonas sp. was followed by complete phenanthrene biodegradation but no further pyrene removal. Totally, the combined process allowed 92% removal of the PAH mixture. Further work should focus on characterizing the photoproducts formed and studying the influence of the solvent on the photodegradation process.     

Conditions for effective removal of pyrene from an artificially contaminated soil using Pseudomonas aeruginosa 57SJ rhamnolipids

The efficacy of a new rhamnolipid biosurfactants mixture to enhance the removal of pyrene from a soil artificially contaminated was investigated. The molar solubilization ratio (MSR) and the partition coefficient between the micelles and water (log K(m)) were found to be 7.5 x 10(-3) and 5.7, respectively. From soil column studies, the pyrene removal increased linearly with the concentration of the injected biosurfactants solution above the effective critical micellar concentration (0.4 g L(-1)). Flushing with a 5.0 g L(-1) biosurfactants solution increased the pyrene concentration in the effluent by 178 times. At high biosurfactants' concentrations (2.5 and 5.0 g L(-1)), the cumulative pyrene recovery reached 70%. This pyrene remobilization takes place independently of the soil organic carbon solubilization. This study provides a combination of batch and column experiments in order to find the conditions for effective soil remediation using a new rhamnolipids mixture.     

Thermally enhanced approaches for bioremediation of hydrocarbon-contaminated soils

Successful remediation of contaminated soils is often limited by the low bioavailability of hydrophobic pollutants, which may slow the process significantly. In this study we investigated the benefits of high temperature in enhancing hydrocarbon degradation rates and evaluated the effect of different biostimulants. Hexadecane polluted soil microcosms with various amendments were incubated both at 60 degrees C and room temperature (18 degrees C) and analyzed periodically up to 40d for the degradation of hydrocarbon and the response of the microbial population. Natural attenuation showed a satisfactory intrinsic degradative capability at 60 degrees C and the addition of inorganic N, P and K increased the degradation rates by 10%. The addition of rhamnolipid biosurfactant further enhanced the bioavailability of alkane to microbial degradation resulting in up to 71% removal at 60 degrees C and 42% at 18 degrees C. Significant input to hexadecane degradation occurred at 60 degrees C (70%) as a result of the bioaugmentation with thermophilic Geobacillus thermoleovorans T80, which did not take place at 18 degrees C. Coupling high temperature to all amendments resulted in 90% removal of the hexadecane from soil after 40d which was also accompanied with an increase in bacterial numbers. The results suggest that thermally enhanced bioremediation may be an efficient technology for the treatment of hydrocarbon-contaminated soils.     

鼠李糖脂协助下的土壤中镉电动修复

实验研究了重金属Cd在生物表面活性剂鼠李糖脂协助下的电动修复过程,通过不同方式、不同浓度、不同酸碱度的鼠李糖脂溶液的添加与空白处理对比,探讨了鼠李糖脂协助下电动修复过程中的Cd在土壤介质中的迁移转化和机理,分析了鼠李糖脂溶液作为电动修复添加剂的可行性。结果表明,中等浓度酸性的鼠李糖脂溶液(pH=4.78,浓度为0.5、1和2 g/L)能对土壤中的重金属Cd进行有效的富集,富集量均在初始值的4倍以上,且其可交换态比重均大于42.07%,非常有利于土壤进行二次修复。此外,以pH=4.78,浓度为0.5 g/L的鼠李糖脂溶液作为预处理剂的Ex-08中的重金属Cd并未出现富集现象,但其对重金属的Cd的总去除效率达到了49.27%。表明利用鼠李糖脂溶液作为电动修复添加剂进行土壤重金属修复是可行的。     

Removal of hydrocarbon from refinery tank bottom sludge employing microbial culture

Accumulation of oily sludge is becoming a serious environmental threat, and there has not been much work reported for the removal of hydrocarbon from refinery tank bottom sludge. Effort has been made in this study to investigate the removal of hydrocarbon from refinery sludge by isolated biosurfactant-producing Pseudomonas aeruginosa RS29 strain and explore the biosurfactant for its composition and stability. Laboratory investigation was carried out with this strain to observe its efficacy of removing hydrocarbon from refinery sludge employing whole bacterial culture and culture supernatant to various concentrations of sand–sludge mixture. Removal of hydrocarbon was recorded after 20 days. Analysis of the produced biosurfactant was carried out to get the idea about its stability and composition. The strain could remove up to 85?±?3 and 55?±?4.5 % of hydrocarbon from refinery sludge when whole bacterial culture and culture supernatant were used, respectively. Maximum surface tension reduction (26.3 mN m^?1) was achieved with the strain in just 24 h of time. Emulsification index (E24) was recorded as 100 and 80 % with crude oil and n-hexadecane, respectively. The biosurfactant was confirmed as rhamnolipid containing C₈ and C₁₀ fatty acid components and having more mono-rhamnolipid congeners than the di-rhamnolipid ones. The biosurfactant was stable up to 121 °C, pH 2–10, and up to a salinity value of 2–10 % w/v. To our knowledge, this is the first report showing the potentiality of a native strain from the northeast region of India for the efficient removal of hydrocarbon from refinery sludge.     

生物与化学表面活性剂协同洗脱土壤中PCBs的研究

通过序批实验和土柱淋洗实验研究了由生物表面活性剂鼠李糖脂(RL)与非离子化学表面活性剂十二烷基醇聚氧乙烯(6)醚(POE(6))混合得到的复配试剂洗脱污染土壤中多氯联苯(PCBs)的作用效果及其作用机理。结果表明,同一土样中,从批实验得到的PCBs洗脱率略高于土柱淋洗实验。RL与POE(6)两种单一试剂对人工污染土样中的PCBs洗脱率均大于60%,而对陈化土样中的洗脱率均不到20%,且土壤中的TOC含量越高,PCBs的洗脱率越低。在质量浓度为301 mg/L(10 CMC)及1 505 mg/L(50 CMC)的RL-POE(6)复配试剂中,RL与POE(6)对人工污染土壤中PCBs的洗脱具有一定的协同作用。当复配试剂的浓度为301 mg/L时,RL与POE(6)对陈化土样中PCBs的洗脱没有协同作用;但当RL-POE(6)的浓度增加到1 505 mg/L时,RL与POE(6)对陈化土样中PCBs的洗脱具有明显的协同作用。     

Effects of remediation train sequence on decontamination of heavy metal-contaminated soil containing mercury

When a contaminated site contains pollutants including both nonvolatile metals and Hg, one single remediation technology may not satisfactorily remove all contaminants. Therefore, in this study, chemical extraction and thermal treatment were combined as a remediation train to remove heavy metals, including Hg, from contaminated soil. A 0.2 M solution of ethylenediamine tetraacetic acid (EDTA) was shown to be the most effective reagent for extraction of considerable amounts of Cu, Pb, and Zn (>50%). Hg removal was ineffective using 0.2 M EDTA, but thermogravimetric analysis suggested that heating to 550°C with a heating rate of 5°C/min for a duration of 1 hr appeared to be an effective approach for Hg removal. With the employment of thermal treatment, up to 99% of Hg could be removed. However, executing thermal treatment prior to chemical extraction reduced the effectiveness of the subsequent EDTA extraction because nonvolatile heavy metals were immobilized in soil aggregates after the 550°C treatment. The remediation train of chemical extraction followed by thermal treatment appears to remediate soils that have been contaminated by many nonvolatile heavy metals and Hg.

ImplicationsA remediation train conjoining two or more techniques has been initialized to remove multiple metals. Better understandings of the impacts of treatment sequences, namely, which technique should be employed first on the soil properties and the decontamination efficiency, are in high demand. This study provides a strategy to remove multiple heavy metals including Hg from a contaminated soil. The interactions between thermal treatment and chemical extraction on repartitioning of heavy metals was revealed. The obtained results could offer an integrating strategy to remediate the soil contaminated with both heavy metals and volatile contaminants.     

老化石油污染土壤的清洗处理

以华北油田老化长达1年以上的石油污染土壤为研究对象,采用自行选配的清洗剂对该污染土壤进行了一次清洗和二次清洗处理.实验结果表明,一次清洗后,污染土壤样品的含油率从26.34%～29.90%降到6.34%～7.84%,洗油率达80.06%～81.06%;经二次清洗处理后,污染土壤样品的含油率从26.34%～29.90%降到4.05%～4.85%,洗油率达88.06%～88.19%.在一次清洗和二次清洗的基础上,通过模拟实验确定了洗油污水回用的最佳回用率为80%,最佳加药质量浓度为0.4 g/L,该条件下污水的最终产生量也较少.按照该参数对华北油田的石油污染土壤进行了清洗实验,洗油率达79.20%～80.51%.