Effect of <Emphasis Type="Italic">Moringa oleifera</Emphasis> Pod Husk Fibers on the Properties of Gelatin-Based Biocomposite

The objective of this work is to study the feasibility of reinforcing polymer composites by utilizing the biofibers from the agricultural residue of Moringa oleifera pod husks (MOPH). The chemical and physical properties of the fibers were comprehensively investigated to evaluate their potential as a filler in gelatin-based films. The effect of MOPH fiber concentrations of 0, 5, 10, and 15 wt% on the water vapor permeability (WVP), and mechanical and thermal properties of the gelatin-based films was studied. By incorporation of 10 wt% of the MOPH fibers in gelatin, the highest tensile strength and Young’s modulus, and the lowest WVP properties were obtained. Scanning electron microscopy (SEM) photographs indicated good interfacial adhesion between the fibers and the gelatin matrix. TGA of the biocomposites revealed an improvement of thermal stability. Moreover, under accelerated weathering, the gelatin-MOPH-10% biocomposite degraded more slowly than the gelatin control. These results indicate that the MOPH fibers are a good reinforcing filler and may be useful for biocomposite applications.     

Extraction of Cellulose Nanocrystals from Phormium tenax Fibres

Cellulose nanocrystals with an acicular structure ranged from 100 to 200 nm in length and 15 nm in width were extracted from Phormium tenax leaf fibres by acid hydrolysis. A two-step procedure for the extraction of nano-sized cellulose was studied and the obtained nanocrystals were characterized using morphological investigations (optical, scanning electron and atomic force microscopy), as well as physico-chemical characterization by Wide Angle X-ray Scattering, infrared spectroscopy and thermogravimetric analysis. A study of birefringence properties was also performed. The first chemical treatment leads to the production of holocellulose by the gradual removal of lignin, while the subsequent sulphuric acid hydrolysis process allows obtaining cellulose nanocrystals in an aqueous suspension. The results reported support the repeatability and the effectiveness of the procedure performed. Moreover, the high cellulose content of P. tenax fibre and their declining market interest, suggest the interest of this investigation and the possibility to use natural fibres for the production of a reinforcement phase to involve in the nanocomposite approach for industrial applications.     

Synthesis,Characterization and Nanocomposite Formation of Poly(glycerol succinate-co-maleate) with Nanocrystalline Cellulose

A novel biodegradable polymer based on glycerol, succinic anhydride and maleic anhydride, poly(glycerol succinate-co-maleate), poly(GlySAMA), was synthesized by melt polycondensation and tested as a matrix for composites with nanocrystalline cellulose. This glycerol-based polymer is thermally stable as a consequence of its targeted cross-linked structure. To broaden its range of properties, it was specifically formulated with nanocrystalline cellulose (NCC) at concentrations of 1, 2 and 4 wt%, and showed improved mechanical properties with NCC. Specifically, the effect of reinforcement on mechanical properties, thermal stability, structure, and biodegradability was evaluated, respectively, by tensile tests and thermogravimetric analyses, X-ray diffraction and respirometry. The neat poly(GlySAMA) polymer proved flexible, exhibiting an elongation-to-break of 8.8 % while the addition of nanowhiskers (at 4 wt%) caused tensile strength and Young’s modulus to increase, 20 and 40 %, respectively. Stiffness improved without significantly decreasing thermal stability as measured by thermogravimetric analysis. Biodegradation tests indicated that all samples were degradable but NCC reduced the rate of biodegradation.     

Preparation and Fundamental Characterization of Cellulose Nanocrystal from Oil Palm Fronds Biomass

The objective of this work was to isolate cellulose nanocrystal (CNC) from oil palm fronds (Elaeis guineensis) and its subsequent characterization. Isolation involves sodium hydroxide/anthraquinone pulping with mechanical refining followed by total chlorine free bleaching (includes oxygen delignification, hydrogen peroxide oxidation and peracetic acid treatment) before acid hydrolysis. Bleaching significantly decreased kappa number and increased α-cellulose percentage of fibers as confirmed by Technical Association of the Pulp and Paper Industry standards. Transmission electron microscopy (TEM), X-ray diffraction, Fourier transform infrared spectroscopy and thermogravimetric analysis revealed that acid hydrolysis along with bleaching improved crystallinity index and thermal stability of the extracted nanocrystals. It was observed that CNC maintained its cellulose 1 polymorph despite hydrolysis treatment. Mean diameter as observed by TEM and average fiber aspect ratio of obtained CNC was 7.44 ± 0.17 nm and 16.53 ± 3.52, respectively making it suitable as a reinforcing material for nanocomposite.     

A Comparative Study of Doum fiber and Shrimp Chitin Based Reinforced Low Density Polyethylene Biocomposites

The aim of this paper was to study the effects of reinforcing low density polyethylene (LDPE) by using bio-fillers (Doum cellulose or Shrimp chitin) on the mechanical properties. Both, Doum cellulose extracted frsom Doum leaves and Shrimp chitin extracted from shrimp co-products were compounded with LPDE without and with compatibilizer. The biocomposites were prepared by melt blending in a twin-screw extruder. Torsion and flexural tests were performed to investigate the impact of each reinforcement on the biocomposite mechanical properties. The SEM was carried out to study the filler/polymer interface adhesion. The present study has demonstrated that Doum fibers and shrimp chitin succeed in improving the mechanical properties of LPDE bio-composites. The results also showed that the use of maleic anhydride-grafted polyethylene as a compatibilizer improves filler adhesion/matrix and mechanical properties. This study exhibits that polyethylene composites based on Doum fibers or shrimp chitin can be used to replace the polyethylene materials in several fields like packaging and automotive industries.     

Optimal Design of Ozone Bleaching Parameters to Approach Cellulose Nanofibers Extraction from Sugarcane Bagasse Fibers

Cellulose nanofibers (CNFs) were isolated from sugarcane bagasse (SCB) through the combination of bio-refinery, sulfur-free, and totally chlorine free (TCF) chemo-mechanical pretreatments, with a focus on the optimal design of ozone bleaching parameters based on a response surface methodology (RSM). For this purpose, the most effective parameters in ozone bleaching (temperature, time, and pulp consistency) were set between 40 and 85 °C, 60 and 360 min, and 1–5 wt%, respectively. High-performance liquid chromatography (HPLC), Fourier transform infrared spectroscopy (FTIR), Kappa number, and scanning electron microscopy (SEM) were used to chemically and morphologically characterize the SCB fibers. The size distribution and morphology of CNFs were also evaluated by dynamic light scattering (DLS) and transmission electron microscopy (TEM). HPLC analysis revealed that percentage of cellulose increased from 41.5 to 91.39% after chemical pretreatments. FTIR and Kappa number analyses also confirmed the successful isolation of cellulose fibers from the SCB fibers after chemical pretreatments. Furthermore, DLS results showed that the hydrodynamic diameter of the isolated cellulose fibers reduced to 268 nm by dint of ultrasonication. Additionally, TEM images confirmed the isolation of CNFs: the average diameter of cellulose fibers decreased to about 28 nm after mechanical steps and the yield of fibrillation was found to be around 99%. According to the obtained results, the applied chemo-mechanical treatment appears to be promising for green and facile isolation of CNFs.     

Biopolymers Based Green Composites: Mechanical, Thermal and Physico-chemical Characterization

Natural cellulosic fibers are one of the smartest materials for use as reinforcement in polymers possessing a number of applications. Keeping in mind the immense advantages of the natural fibers, in present work synthesis of natural cellulosic fibers reinforced polymer composites through compression molding technique have been reported. Scanning Electron microscopy (SEM), Thermo gravimetric/Differential thermal/Derivative Thermogravimetry (TGA/DTA/DTG), absorption in different solvents, moisture absorbance, water uptake and chemical resistance measurements were used as characterization techniques for evaluating the different behaviour of cellulosic natural fibers reinforced polymer composites. Effect of fiber loading on mechanical properties like tensile strength, flexural strength, compressive strength and wear resistances has also been determined. Reinforcing of the polymer matrix with natural fibers was done in the form of short fiber. Present work indicates that green composites can be successfully fabricated with useful mechanical properties. These composites may be used in secondary structural applications in automotive, housing etc.     

Preparation and Properties of Green Composites Based on Tapioca Starch and Differently Recycled Paper Cellulose Fibers

Green composites obtained from biodegradable renewable resources have gained much attention due to environmental problems resulting from conventionally synthetic plastics and a global increasing demand for alternatives to fossil resources. In this work we used different cellulose fibers from used office paper and newspaper as reinforcement for thermoplastic starch (TPS) in order to improve their poor mechanical, thermal and water resistance properties. These composites were prepared by using tapioca starch plasticized by glycerol (30 % wt/wt of glycerol to starch) as matrix reinforced by the extracted cellulose fibers with the contents ranging from 0 to 8 % (wt/wt of fibers to matrix). Properties of composites were determined by mechanical tensile tests, differential scanning calorimetry, thermogravimetric analysis, water absorption measurements, scanning electron microscopy, and soil burial tests. The results showed that the introduction of either office paper or newspaper cellulose fibers caused the improvement of tensile strength and elastic modulus, thermal stability, and water resistance for composites when compared to the non-reinforced TPS. Scanning electron microscopy showed a good adhesion between matrix and fibers. Moreover, the composites biological degraded completely after 8 weeks but required a longer time compared to the non-reinforced TPS. The results indicated that these green composites could be utilized as commodity plastics being strong, inexpensive, plentiful and recyclable.     

Thermally Stable Pyrolytic Biocarbon as an Effective and Sustainable Reinforcing Filler for Polyamide Bio-composites Fabrication

Natural fibers are limited in their use as reinforcement to commodity polymers. They cannot be used to reinforce engineering polymers due to their low thermal stability at high processing temperatures. This study presents an approach to successfully reinforce polyamides using a derivative of natural fibers as reinforcement without the effects of thermal degradation during melt processing. Biocarbon from miscanthus fibers was used to reinforce polyamide 6 up to 40 wt%. At 40 wt% filler content, the tensile and flexural strengths increased by 19.6 and 47% respectively in comparison to the neat polyamide. The moduli were also increased by 31.5 and 63.7% respectively. A maximum increase in impact strength of 43.7% was achieved at 20 wt% biocarbon loading. The morphology of the tensile fractured samples showed stretched polyamide ligaments attached to the biocarbon particles, indicating the presence of interaction between filler and matrix. Interestingly, more bonded interfaces were observed between the polyamide and biocarbon particles with increasing biocarbon content possibly stemming from increased biocarbon surfaces with functional groups. These composites show great potential to substitute in part or whole, some particulate filled polyamides currently used in the automotive industry.     

The Influence of Artificial Photodegradation on Properties of Poly(3-hydroxybutyrate-<Emphasis Type="Italic">co</Emphasis>-3-hydroxyvalerate)(PHBV)/Graphite Nanosheets (GNS) Nanocomposites

The potential use of poly(3-hydroxybutyrate-co-3-hydroxyvalerate)/graphite nanosheets (GNS) as a biodegradable nanocomposite has been explored. PHBV/GNS nanocomposites films were prepared by solution casting at various concentrations of GNS—0.25, 0.50 and 1.00 wt% GNS. The films were exposed to artificial ultraviolet radiation (UV) during 52 h. The effect of GNS on PHBV photodegradation was investigated and compared to neat PHBV film. The artificial photodegradation induced changes in physical (weight loss), chemical carbonyl index by Fourier transform infrared spectroscopy, thermal degree of crystallinity and melting temperature by differential scanning calorimetry and morphological scanning electron microscopy characteristics. Based on the results obtained from aforementioned analyzes it was verified that GNS inhibits the oxidative degradation of PHBV matrix.     

Dispersing Bacterial Cellulose Nanowhiskers in Polylactides via Electrohydrodynamic Processing

In the present study, hybrid electrospun polylactide (PLA) fibers reinforced with highly dispersed crystalline bacterial cellulose nanowhiskers (BCNW) in solution concentrations up to 15 wt% were developed and characterized. The overall aim was to encapsulate dispersed BCNW in fibers to be later re-dispersed in virgin PLA by melt compounding. Initially, the suitability of three different solvents [1,1,1,3,3,3-hexafluoro-2-propanol (HFP), acetone–chloroform and chloroform/polyethylene glycol (PEG)] for fiber production was evaluated and solutions containing 5 wt% BCNW were used to generate electrospun hybrid PLA fibers. These fibers presented a homogeneous morphology, as assessed by scanning electron microscopy, and transmission electron microscopy images demonstrated that BCNW were well distributed along the fibers. Differential scanning calorimetry analyses showed that the incorporation of PEG into the fibers resulted in a T_g drop due to a plasticization effect and decreased thermal stability as a result of low interactions between the matrix and the BCNW. Subsequently, fibers were produced from the selected solutions (HFP and acetone–chloroform) containing up to 15 wt% BCNW. As a result of the great increase in the viscosity of the solutions, lower solids contents were required, leading to a better dispersion and incorporation degree of BCNW within the fibers. HFP was found to be a more suitable solvent, since higher incorporation levels were estimated by X-ray diffraction and improved matrix–filler interactions were suggested by a slight increase in the T_g of the fibers.     

Green Synthesis and Antioxidant Study of Silver Nanoparticles of Root Extract of <Emphasis Type="Italic">Sageretia thea</Emphasis> and Its Role in Oxidation Protection Technology

Development of environmentally friendly synthesis of nanoparticles is one of the important areas of research in nanotechnology. In present study silver naopartticles (AgNPs) of root extract of Sageretia thea (S. thea) were synthesized at room temperature. The synthesized AgNPs were characterized by UV. Visible spectroscopy (UV), scanning electron microscopy (SEM), X-ray diffraction (XRD), energy dispersive spectroscopy (EDX), transmission electron microscopy (TEM), dynamic light scattering (DLS) and Fourier transform infrared (FT-IR) spectroscopy. Formation of AgNPs was confirmed by visual examination the colour change from yellow to brick red due to surface Plasmon resonance band at 435 nm. SEM and TEM analysis of synthesized AgNPs revealed spherical morphology with average particle size 25 nm. Crystalline nature of the AgNPs in face centered cubic structure is evident from the selected area electron diffraction (SAED) and XRD pattern. The presence of elemental Ag was confirmed by EDX analysis at 3kv. Different functional groups which responsible for reduction and stabilization of reaction medium was confirmed by FTIR spectroscopy. The biosynthesized AgNPs showed strong DPPH and dye protection radical scavenging assay while modest hydrogen peroxide radical scavenging assay as compare to crude extract. The present investigations suggest that biosynthesized nanoparticles have a high potential for use in the preparation of drugs used against various diseases and also a promising candidate for many medical applications.     

Isolation and Characterization of Nanocrystalline Cellulose from Totally Chlorine Free Oil Palm Empty Fruit Bunch Pulp

Nanocrystalline cellulose (NCC) was isolated from a totally chlorine free (TCF) bleached oil palm empty fruit bunch (OPEFB) pulp via acid hydrolysis using a 58 % sulfuric acid concentration and ultrasonic treatment. The effects of acid concentration and hydrolysis time were investigated. Characterization of OPEFB–NCC was carried out using TEM, FTIR, ¹³C-NMR, XRD, zeta potential and TGA. The optimal hydrolysis time was 80 min as indicated by the leveling off of the OPEFB–NCC dimensions (length 150 nm and diameter 6.5 nm) with no significant loss of crystallinity at this point. The presence of a shoulder peak at 1231 cm^?1 (assigned to a sulfate group) in the FTIR spectrum of NCC is indicative of a successful esterification. This is further corroborated by the ¹³C-NMR analysis whereby the distinct C4 amorphous and crystalline peaks present in OPEFB–TCF pulp had almost disappeared and the cluster of signals for C2, C3, C5, and a well separated signal of C6 had merged into one single peak in the OPEFB–NCC sample. These observations allude to most of the amorphous region having been removed and to the strong possibility of sulfonation having not only occurred on the C6, but also on C2 and C3. OPEFB–NCC isolated over shorter hydrolysis time was more thermally stable; however, the char fraction decreases with hydrolysis time despite having a higher zeta potential. The results of this investigation demonstrate that NCC can be produced from pulp made by chlorine free environmentally benign processes with ensuing savings in energy and chemicals.     

Characterization of Super Paramagnetic Nanoparticles Coated with a Biocompatible Polymer Produced by Dextransucrase from <Emphasis Type="Italic">Weissella cibaria</Emphasis> JAG8

Magnetic nanoparticles (MNPs) synthesised by chemical co-precipitation method was subjected to dextran coating by sonication method. The dextran was enzymatically synthesised by extracellular dextransucrase isolated from Weissella cibaria JAG8. The crystalline nature of MNPs and dextran coated MNPs were confirmed by X-ray diffraction studies with average particle size of 25 nm, which was confirmed further by high resolution transmission electron microscopy. The surface morphology of MNPs and dextran coated MNPs were monitored by scanning electron microscopy studies. The vibrating sample magnetometer investigation displayed the super paramagnetic nature of MNPs and dextran coated MNPs. FT-IR analysis of MNPs and dextran coated MNPs, displayed characteristic band of Fe–O bond at 582 cm^?1. Thermo-gravimetric analysis of MNPs and dextran coated MNPs (1:1) ratio displayed a weight loss of 15 and 18 %, which clearly indicated 3.0 % of dextran was coated on to the MNPs. The elemental composition study by scanning electron microscopy confirmed the association of dextran with MNPs. The in vitro effect of MNPs and dextran coated MNPs was performed on human colon cancer (HT-29) cell lines and the results showed that dextran coated: MNPs (2:1) displayed good biocompatibility results over dextran coated: MNPs (1:1) and un-coated MNPs.     

Lignocellulosic Fiber-Reinforced Keratin Polymer Composites

Short fiber reinforced polymer composites were prepared from lignocellulose fibers and feather keratin polymer (FKP). The FKP matrix was prepared from the reactive processing of poultry feather keratin, glycerol, water, and sodium sulfite. Lignocellulose fibers of varying source, length, and mass fraction were used and it was found that positive reinforcement of FKP was affected by all three. Positive reinforcement was defined as an increase in elastic modulus when normalized by FKP with the same amount of glycerol but no fibers. Positive reinforcement was only able to occur for modulus but not stress at break indicating that the composites were of high physical properties only under small deformations. At large deformations, fiber pull-out was observed in the composites using scanning electron microscopy. The most likely origin of this behavior appeared to be from weak fiber–polymer interactions dominated by friction and rationalized by a force balance across the fiber–polymer interface. High fiber loadings were shown to be reinforcing because of the formation of a network of lignocellulose fibers. The addition of lignocellulose fibers increased the thermal stability of the material.     

Preparation and Properties of a Chitosan–Hyaluronic Acid-Polypyrrole Conductive Hydrogel Catalyzed by Laccase

Electro conductive hydrogels, consisting of chitosan (CS), hyaluronic acid (HA), and polypyrrole (PPy), were prepared via an in situ enzymic polymerization of pyrrole in the CS–HA hydrogel, using laccase as the catalyst. This CS–HA–PPy composite hydrogel showed good conductivity. The chemical structure and morphology of this conductive hydrogel were studied by Fourier transform infrared spectroscopy, scanning electron microscopy, and X-ray diffraction technique. For CS–HA–PPy and CH–HA hydrogel, the temperature at which fastest decomposition occurred was 260 and 244 °C, respectively. That means the thermal stability of CS–HA–PPy is better than CS–HA hydrogel. The conductive hydrogel also showed excellent swelling and deswelling behaviors.     

Effect of Gamma Radiation on the Properties of Crosslinked Chitosan Nano-composite Film

Chitosan nano-composite film crosslinked by citric acid and with glycerol as plasticizer and MgO as antibacterial agent was prepared by casting method. MgO nanoparticles were synthesized via calcination method in furnace at 500 °C for 4 h and characterized by X-ray diffraction and transmission electron microscope. The chitosan nano-composite film with composition chitosan/citric/glycerol/magnesium oxide (1 wt%:1 wt%:75 vol%:10 wt%) has high mechanical properties than other films. The effects of different irradiation doses on the mechanical, thermal and antibacterial activity were investigated. The tensile strength enhanced by increasing irradiation dose up to 10 kGy and the elongation negligible changed as irradiation dose increased. The thermal stability slightly increased up to dose 2.5 kGy then decreased with dose increment. The antimicrobial activity film was studied against white mulberry-borne bacterial pathogens either Gram positive or Gram negative bacteria and has positive impact of gamma irradiation on the antimicrobial activity. The use of the selected chitosan nano-composite film which irradiated by dose of 2.5 kGy and has magnesium oxide of average particle size 54.3 nm as new packaging materials found to improve storage quality and shelf-life of mulberry fruit.     

Some Investigations on the Nylon 6/Zn Composite Material Obtained by Simultaneous Anionic Polymerization-Molding Process

This study is concerned with the behavior of samples based on nylon 6/zinc (Ny6/Zn) composite material in high salinity water that contains NaCl (3.5 wt%) and in aqueous solution of HCl (0.5 N and 1 N). The samples were obtained from parts prepared by in situ anionic ring-opening polymerization of ?-caprolactam (CL) in the presence of zinc (Zn), as filler (15 wt%) using the rotational molding technique. This type of composite was evaluated by the testing of swelling degree, structural modifications, evolution of hydrogen and electrochemical behavior. The properties of Ny6/Zn composite material have ascertained through the combined use of more analysis methods: attenuated total reflectance Fourier transform infrared spectroscopy, wide-angle X-ray diffraction technique, scanning electron microscopy, swelling and electrochemical measurements. It was revealed that regarding swelling behavior the Ny6 matrix has an important role while Zn filler contributes especially to the (electro)chemical corrosion.     

Mechanical, Thermal and Water Absorption Properties of Kenaf-Fiber-Based Polypropylene and Poly(Butylene Succinate) Composites

The use of composites made from non-biodegradable conventional plastic materials (e.g., polypropylene, PP) is creating global environmental concern. Biodegradable plastics such as poly(butylene succinate) (PBS) are sought after to reduce plastic waste accumulation. Unfortunately, these types of plastics are very costly; therefore, natural lignocellulosic fibers are incorporated to reduce the cost. Kenaf fibers are also incorporated into PP and PBS for reinforcing purposes and they have low densities, high specific properties and renewable sourcing. However without good compatibilization, the interfacial adhesion between the matrix and the fibers is poor due to differences in polarity between the two materials. Maleic anhydride-grafted compatibilizers may be introduced into the system to improve the matrix-fiber interactions. The overall mechanical, thermal and water absorption properties of PP and PBS composites prepared with 30 vol.% short kenaf fibers (KFs) using a twin-screw extruder were being investigated in this study. The flexural properties for both types of composites were enhanced by the addition of compatibilizer, with improvements of 56 and 16 % in flexural strength for the PP/KF and PBS/KF composites, respectively. Good matrix-fiber adhesion was also observed by scanning electron microscopy. However, the thermal stability of the PBS/KF composites was lower than that of the PP/KF composites. This result was confirmed by both DSC and TGA thermal analysis tests. The water absorption at equilibrium of a PBS composite filled with KFs is inherently lower than of a PP/KF composite because the water molecules more readily penetrate the PP composites through existing voids between the fibers and the matrix. Based on this research, it can be concluded that PBS/KF composites are good candidates for replacing PP/KF composites in applications whereby biodegradability is essential and no extreme thermal and moisture exposures are required.