Waste polyvinylchloride derived pitch as a precursor to develop carbon fibers and activated carbon fibers

Polyvinylchloride (PVC) was successfully recycled through the solvent extraction from waste pipe with an extraction yield of ca. 86%. The extracted PVC was pyrolyzed by a two-stage process (260 and 410 degrees C) to obtain free-chlorine PVC based pitch through an effective removal of chlorine from PVC during the heat-treatment. As-prepared pitch (softening point: 220 degrees C) was spun, stabilized, carbonized into carbon fibers (CFs), and further activated into activated carbon fibers (ACFs) in a flow of CO2. As-prepared CFs show comparable mechanical properties to commercial CFs, whose maximum tensile strength and modulus are 862 MPa and 62 GPa, respectively. The resultant ACFs exhibit a high surface area of 1200 m2/g, narrow pore size distribution and a low oxygen content of 3%. The study provides an effective insight to recycle PVC from waste PVC and develop a carbon precursor for high performance carbon materials such as CFs and ACFs.     

Kinetics of thermal de-chlorination of PVC under pyrolytic conditions

Although PVC-containing wastes are an important potential source of energy they are frequently disposed in landfill. In thermal treatment processes such as pyrolysis and gasification, the presence of poly(vinyl chloride) (PVC), a compound with 56.7% of chlorine, may cause problems concerned with environmental protection, as consequence of the formation of hydrochloric acid, chlorine gas and dioxins, as well as corrosion phenomena of the reactor/equipment materials. Thus, a possible solution may involve a previous removal of the chlorine from PVC containing waste through a pyrolysis process at low temperatures before the material being submitted to a subsequent thermal treatment, for energetic valorization. In this work, a kinetic model for the thermal decomposition of PVC has been developed, in view of its de-chlorination. DTA/TGA testing at different temperatures indicated a first order reaction and an activation energy of 133,800J/mol. An almost completed de-chlorination reaction was obtained at 340°C under an inert atmosphere. The resulted material is a C(n)H(n) type polymer with potential to be used in an energy recovery process. Validation test performed at laboratory scale indicate that the temperature of 340°C enables the removal of ～99.9% of the chlorine present in PVC. The chloride can be fixed in the form of an aqueous solution of HCl or calcium chloride, driving to an alternative full process with environmental benefits and reduction of the costs associated to the PCV - containing materials/wastes management.     

Preparation and Characterization of PVC Matrix Composites with Biochemical Sludge

Biochemical sludge (BS), generated in the waste water treatment of paper mills, was pretreated by enzyme hydrolysis. The effect and action mechanism of the enzymatic treatment on the properties of polyvinyl chloride (PVC) matrix composites with BS were discussed. Results showed that when the filler content was 30 wt%, the tensile strength of the PVC composites filled with BS and its modified products which were pretreated by laccase, cellulase and hemicellulase can be increased by 38.64, 67.4, 63.5 and 66.3% than the PVC composite filled with calcium carbonate. When the dosage of filler was 40 wt%, the elastic modulus of PVC composites filled with BS and its above three modified products decreased by 53.3, 52.3, 50.0 and 46.3%, respectively. Meanwhile, the thermal stability of PVC composites can also be improved at the temperature of over 340 °C. It can be concluded that the enzyme pretreatment can improve the application performance of BS usage in PVC matrix composites.     

Influence of poly(bisphenol A carbonate) and poly(ethylene terephthalate) on poly(vinyl chloride) dehydrochlorination

Recycling of poly(vinyl chloride) (PVC) waste is a serious problem because of its high chlorine content. Dehydrochlorination of PVC-containing polymer waste produces solid residue char, for which conversion to pyrolysis oil in a petrochemical plant seems to be an attractive way of recycling PVC waste. Unfortunately, some polymer admixtures react with HCl and cause formation of chloroorganic compounds in a char. This article describes the influence of polycarbonates and poly(ethylene terephthalate) on thermal feedstock recycling of PVC wastes using a two-stage method. It was found that the presence of polycarbonate causes the formation of small amounts of benzyl chloride and other chloroaryl or chloroalkylaryl compounds. Poly(ethylene terephthalate) interacts with HCl forming significant amounts of various chlorocompounds – mainly chloroethyl esters of terephthalic and benzoic acids, but derivatives possessing chlorine directly connected to the aromatic ring are also formed.     

Investigation of thermal treatment on selective separation of post consumer plastics prior to froth flotation

Plastics have become the widely used materials because of their advantages, such as cheapness, endurance, lightness, and hygiene. However, they cause waste and soil pollution and they do not easily decompose. Many promising technologies are being investigated for separating mixed thermoplastics, but they are still uneconomical and unreliable. Depending on their surface characteristics, these plastics can be separated from each other by flotation method which is useful mineral processing technique with its low cost and simplicity.The main objective of this study is to investigate the flotation characteristics of PET and PVC and determine the effect of plasticizer reagents on efficient plastic separation. For that purpose, various parameters such as pH, plasticizer concentration, plasticizer type, conditioning temperature and thermal conditioning were investigated. As a result, PET particles were floated with 95.1% purity and 65.3% efficiency while PVC particles were obtained with 98.1% purity and 65.3% efficiency.     

Upgrading of poly(vinyl chloride) by chemical modifications using sodium sulfide

The recycling of poly(vinyl chloride) (PVC) is one of the most important issues in the treatment of waste plastics. To improve PVC recycling, it is necessary to develop new recycling techniques, including new techniques for the dechlorination of chlorine-containing polymers. It has been established that wet dechlorination of PVC in NaOH/ethylene glycol solution is more effective than dry dechlorination. In this study, the wet process was used, and the chemical modification of PVC by nucleophilic substitution was considered for upgrading waste PVC. Chlorine was substituted in solution by several nucleophilic reagents, thus changing the properties of PVC. The reaction of PVC in Na2S/ethylene glycol solution at 170°C resulted in the formation of a mixture comprising 32% elimination and 26% substitution products. The scanning electron microscopy/energy dispersive X-ray spectroscopy mappings and elementary analysis of PVC indicated that this chlorine-substitution process led to cross-linking by sulfur.     

Recent progress on preparation and properties of nanocomposites from recycled polymers: A review

Currently, the growing consumption of polymer products creates the large quantities of waste materials resulting in public concern in the environment and people life. Nanotechnology is assumed the important technology in the current century. Recently, many researchers have tried to develop this new science for polymer recycling. In this article, the application of different nanofillers in the recycled polymers such as PET, PP, HDPE, PVC, etc. and the attributed composites and blends is studied. The morphological, mechanical, rheological and thermal properties of prepared nanocomposites as well as the future challenges are extensively discussed. The present article determines the current status of nanotechnology in the polymer recycling which guide the future studies in this attractive field.     

Mechanical, Thermal and Water Absorption Properties of Kenaf-Fiber-Based Polypropylene and Poly(Butylene Succinate) Composites

The use of composites made from non-biodegradable conventional plastic materials (e.g., polypropylene, PP) is creating global environmental concern. Biodegradable plastics such as poly(butylene succinate) (PBS) are sought after to reduce plastic waste accumulation. Unfortunately, these types of plastics are very costly; therefore, natural lignocellulosic fibers are incorporated to reduce the cost. Kenaf fibers are also incorporated into PP and PBS for reinforcing purposes and they have low densities, high specific properties and renewable sourcing. However without good compatibilization, the interfacial adhesion between the matrix and the fibers is poor due to differences in polarity between the two materials. Maleic anhydride-grafted compatibilizers may be introduced into the system to improve the matrix-fiber interactions. The overall mechanical, thermal and water absorption properties of PP and PBS composites prepared with 30 vol.% short kenaf fibers (KFs) using a twin-screw extruder were being investigated in this study. The flexural properties for both types of composites were enhanced by the addition of compatibilizer, with improvements of 56 and 16 % in flexural strength for the PP/KF and PBS/KF composites, respectively. Good matrix-fiber adhesion was also observed by scanning electron microscopy. However, the thermal stability of the PBS/KF composites was lower than that of the PP/KF composites. This result was confirmed by both DSC and TGA thermal analysis tests. The water absorption at equilibrium of a PBS composite filled with KFs is inherently lower than of a PP/KF composite because the water molecules more readily penetrate the PP composites through existing voids between the fibers and the matrix. Based on this research, it can be concluded that PBS/KF composites are good candidates for replacing PP/KF composites in applications whereby biodegradability is essential and no extreme thermal and moisture exposures are required.     

Selective separation of virgin and post-consumer polymers (PET and PVC) by flotation method

More and more polymer wastes are generated by industry and householders today. Recycling is an important process to reduce the amount of waste resulting from human activities. Currently, recycling technologies use relatively homogeneous polymers because hand-sorting waste is costly. Many promising technologies are being investigated for separating mixed thermoplastics, but they are still uneconomical and unreliable. At present, most waste polymers cause serious environmental problems. Burning polymers for recycling is not practiced since poisonous gases are released during the burning process. Particularly, polyvinyl chloride (PVC) materials among waste polymers generate hazardous HCl gas, dioxins containing Cl, etc., which lead to air pollution and shorten the life of the incinerator. In addition, they make other polymers difficult to recycle.Both polyethylene terephthalate (PET) and PVC have densities of 1.30–1.35 g/cm³ and cannot be separated using conventional gravity separation techniques. For this reason, polymer recycling needs new techniques. Among these techniques, froth flotation, which is also used in mineral processing, can be useful because of its low cost and simplicity.The main objective of this research is to recycle PET and PVC selectively from post-consumer polymer wastes and virgin polymers by using froth flotation. According to the results, all PVC particles were floated with 98.8% efficiency in virgin polymer separation while PET particles were obtained with 99.7% purity and 57.0% efficiency in post-consumer polymer separation.     

Processing plastics from ASR/ESR waste: separation of poly vinyl chloride (PVC) by froth flotation after microwave-assisted surface modification

The feasibility of the selective surface hydrophilization of poly vinyl chloride (PVC) using microwave treatment to facilitate the separation of PVC via froth flotation from automobile shredder residue (ASR) and electronic waste shredder residue (ESR) was evaluated. In the presence of powder-activated carbon (PAC), 60-s microwave treatment selectively enhanced the hydrophilicity of the PVC surface (i.e., the PVC contact angle decreased from 86.8° to 69.9°). The scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) results are consistent with increased hydrophilic functional groups (i.e., ether, hydroxyl, and carboxyl), amounting to significant changes in the morphology and roughness of the PVC surface after treatment. After only 60 s of microwave treatment, 20 % of the PVC was separated in virgin and ASR/ESR plastics with 33 and 29 % purity, respectively, as settled fractions by froth flotation at a 150 rpm mixing speed. The microwave treatment with the addition of PAC had a synergetic effect with the froth flotation, which brought about 100 and 90 % selective separation of PVC from the other virgin and ASR/ESR plastics, with 91 and 82 % purity. The use of the combined froth flotation and microwave treatments is an effective technology for separating PVC from hazardous waste plastics.     

Temporary structures as a generator of waste in covered trade fairs

Events like trade fairs are a complex service activity with a considerable economic, social and environmental impact due, among other factors, to their high level of waste generation. There are few studies of the environmental impact associated with waste generation and typology. An environmental analysis methodology has been developed to characterise the waste associated with the temporary structures used at trade fair events: stands and communal spaces.This methodology has been checked in a pilot test at 6 closed trade fairs in Barcelona, with a range of between 60 and 4400 exhibitors. The methodology developed has made possible to obtain a waste generation profile according to the size of the fair and the types of stands. The stages with the largest amount of temporary structure wastes generated are the assembly and the dismantling of the trade fair.The results indicate that the most common wastes generated are the protective plastic from carpets at the assembly stage and the carpet itself at the dismantling stage. The stand carpet is collected in bulk, while the carpet from the communal spaces is recycled. As the size of the fair increases, and with it the proportion of stands with customised design (or non-reusable stands), the quantity of wood and hazardous waste increases.     

Alkaline hydrolysis of PVC-coated PET fibers for simultaneous recycling of PET and PVC

Journal of Material Cycles and Waste Management - Polyvinyl chloride (PVC)-coated poly(ethylene terephthalate) (PET) woven fibers are one of the hardest-to-recycle polymeric materials. Herein we...     

Thermal treatment and decontamination of mercury-contaminated waste: Recent developments and comparative evaluation

The land disposal restriction regulations have necessitated development of technologies for the treatment of wastes and soils containing mercury. Of all the treatment methods, thermal technologies are the most advanced and proven for a variety of mercury-contaminated waste materials. During the past few years, a number of thermal treatment processes have been developed both for listed and characteristic waste. A review of the technologies identified six that are in either commercial or pilot plant stages. The biggest volumes of waste currently occur in the gas processing and caustic-chlorine industries, so most of the technologies being used appear to have been developed around the characteristics of these two wastes. This article discusses the characteristics of each of the six available thermal treatment processes, and describes the types of mercury-contaminated wastes these technologies have been designed to handle.     

Hydro-erosive separation of plastic fibers from textile compounds

There are no known methods which will effectively separate compounds consisting of plastic fibers and latex binders, or plastics coated with textiles. To separate the fibers and the plastic carrier from the other materials, high-pressure water jets have been used. Based on this practice, a method was developed to treat waste carpets and automotive interior materials with water jets in order to recycle their plastic components. Experiments were performed to investigate the modes of destruction as well as the influence of process parameters. Based on these investigations, a pilot device for the treatment of waste carpets (sheets or chips) was designed and installed. It was shown that the proposed method works with a high degree of cleanliness and selectivity. A general process scheme was developed in order to apply the method to recycling processes.     

Pyrolysis kinetics of waste PVC pipe.

The pyrolysis kinetics of waste PVC pipe was investigated with a thermal gravimetric analysis system at heating rates of 5, 10, and 30 degrees C/min in a nitrogen atmosphere. Freeman-Carroll method was employed to evaluate kinetic parameters. Two dominant peaks were observed on derivative gravimetric curves, hypothetically suggesting a two-stage apparent reaction model. The first-stage reaction was likely to be represented by stoichiometric reaction to yield volatiles (mainly HCl) and intermediates. The second-stage reaction might be described by thermal degradation of intermediates competitively into gas, liquid, and solid by-products. Quasi-isothermal operations were introduced to verify the reaction types of the first and second reaction. The generation reaction of intermediates achieved at lower temperatures was carried out independently with their decomposition reaction at higher temperatures. The effects of additives on the pyrolysis kinetics of waste PVC pipe seem to be significant, especially on the first-stage reaction. The first-stage reaction was retarded. A merged peak at low temperatures was observed on the derivative thermogravimetry (DTG) curve instead of two peaks usually observed for that of pure PVC resin. The first peak on the DTG curve of pure PVC resin may shift more, resulting in the complete overlap of two peaks. The quantity of evolved HCl was likely to decrease because of interaction of metal components of stabilizers with either HCl or active chlorine atom or both. The final residual fraction increased as a result of pyrolysis of organic forms of additives to yield extra char. On the other hand, the second-stage reaction kinetics demonstrates a similar pattern to that of pure PVC resin, implying that the effects of additives may be less significant in comparison with that at the first-stage reaction.     

Chemical recycling of waste Poly Vinyl Chloride (PVC) by the liquid-phase treatment

Journal of Material Cycles and Waste Management - Liquid-phase treatment of waste Poly Vinyl Chloride (PVC) was performed. Chlorine change rate was high when using alcohol, cresol and terpene...     

Development of a catalytic dehalogenation (Cl,Br) process for municipal waste plastic-derived oil

Dehalogenation is a key technology in the feedstock recycling of mixed halogenated waste plastics. In this study, two different methods were used to clarify the effectiveness of our proposed catalytic dehalogenation process using various carbon composites of iron oxides and calcium carbonate as the catalyst/sorbent. The first approach (a two-step process) was to develop a process for the thermal degradation of mixed halogenated waste plastics, and also develop dehalogenation catalysts for the catalytic dehydrochlorination of organic chlorine compounds from mixed plastic-derived oil containing polyvinyl chloride (PVC) using a fixed-bed flow-type reactor. The second approach (a single-step process) was the simultaneous degradation and dehalogenation of chlorinated (PVC) and brominated (plastic containing brominated flame retardant, HIPS–Br) mixed plastics into halogen-free liquid products. We report on a catalytic dehalogenation process for the chlorinated and brominated organic compounds formed by the pyrolysis of PVC and brominated flame retardant (HIPS–Br) mixed waste plastics [(polyethylene (PE), polypropylene (PP), and polystyrene (PS)], and also other plastics. During dehydrohalogenation, the iron- and calcium-based catalysts were transformed into their corresponding halides, which are also very active in the dehydrohalogenation of organic halogenated compounds. The halogen-free plastic-derived oil (PDO) can be used as a fuel oil or feedstock in refineries.     

Report: waste refinery in the municipality of Bor?s.

This paper briefly describes waste treatment trends in Sweden and describes an example of state-of-the-art treatment in a local integrated waste treatment system (Bor?s). The focus is on treatment of household waste, to illustrate what can be done to establish a sustainable waste treatment system with high recovery of materials and energy. The various processes have resulted in a low amount of landfilled household waste, and high proportions of recovered energy and materials. Heat, electricity, vehicle fuel and fertilizers, metals and construction materials are recovered from the local waste in Bor?s, with less than 4% of domestic waste being sent to landfill.     

Soil reinforcement with recycled carpet wastes.

A root or fibre-reinforced soil behaves as a composite material in which fibres of relatively high tensile strength are embedded in a matrix of relatively plastic soil. Shear stresses in the soil mobilize tensile resistance in the fibres, which in turn impart greater strength to the soil. A research project has been undertaken to study the influence of synthetic fibrous materials for improving the strength characteristics of a fine sandy soil. One of the main objectives of the project is to explore the conversion of fibrous carpet waste into a value-added product for soil reinforcement. Drained triaxial tests were conducted on specimens, which were prepared in a cylindrical mould and compacted at their optimum water contents. The main test variables included the aspect ratio and the weight percentage of the fibrous strips. The results clearly show that fibrous inclusions derived from carpet wastes improve the shear strength of silty sands. A model developed to simulate the effect of the fibrous inclusions accurately predicts the influence of strip content, aspect ratio and confining pressure on the shear strength of reinforced sand.     

Simultaneous treatment of PVC and oyster-shell wastes by mechanochemical means

This work presents a new process for dechlorinating poly-vinyl chloride (PVC) by the use of oyster-shell waste. The process consists of milling of PVC waste with oyster-shell waste, followed by washing the milled sample with water. The milling of PVC and oyster-shell mixture results in size reduction and rupture in bonds, leading to mechanically induced reactions between the two to form CaCl2 and hydrocarbon with C=C bonds. Washing the milled mixtures with water at room temperature allows complete removal of chlorine from the milled sample. More than 95% of chlorine in PVC was removed when 2h grinding is conducted for the mixture. The present process could offer a potential route to the handling and disposal of oyster-shell and PVC wastes.