锰铁氧体吸附及催化柠檬酸还原六价铬的过程及机理

本文探究了磁性纳米铁锰氧体(MnFe_2O_4)及其黏土矿物负载材料对六价铬(Cr(Ⅵ))的吸附作用,同时研究了锰铁氧体-柠檬酸溶液体系中,铁锰氧体催化柠檬酸还原Cr(Ⅵ)的机理.结果表明,MnFe_2O_4材料对Cr(Ⅵ)的吸附量随着吸附时间的增加而增加,在0—5 min内快速吸附并达到平衡,符合准二级动力学模型.伴随MnFe_2O_4负载量的增加,凹凸棒土负载铁锰氧体(ATP-Fe Mn)的吸附量大幅增加,ATP-FeMn14吸附量最大达到了29.2 mg·g~(-1),且吸附等温线均可用Langmuir方程或Freundlich方程拟合,属于单分子层吸附.MnFe_2O_4和负载ATP材料吸附Cr(Ⅵ)的最佳pH值为3—4,ATP-FeMn14对六价铬的去除率最高,最佳投加量为5 g·L~(-1).在铁锰氧体-柠檬酸体系中,溶液pH值是影响Cr(Ⅵ)的去除效率的重要因素,当溶液pH值在4和5时,Cr(Ⅵ)的去除率(76.5%、66.2%)显著高于其他处理;4 mmol·L~(-1)柠檬酸的处理去除率(89.8%)显著高于其他浓度柠檬酸的处理去除率;而在相同体系中,MnFe_2O_4的处理去除率(89.8%)显著高于其他研究材料.本研究表明铁锰氧体不仅对Cr(Ⅵ)具有良好的吸附性能,在与有机酸共存时,还可以催化有机酸还原Cr(Ⅵ),降低Cr(Ⅵ)的环境风险.     

凹凸棒石和海泡石对镉离子的吸附效果

采用静态批试验方法研究了凹凸棒石和海泡石对溶液中Cd~(2+)的吸附特性,并通过考察一定离子强度下,不同初始浓度、固液比、吸附时间和pH值对吸附镉的影响。结果显示:在0.01 mol·L~(-1)NaNO_3离子强度下,高品位海泡石、凹凸棒石和低品位凹凸棒石对溶液中Cd~(2+)的吸附量与初始浓度呈正比,与固液比呈反比;根据Langmuir等温吸附方程拟合结果,在给定离子强度25℃条件下黏土矿物Cd~(2+)的理论饱和吸附量从大到小依次为高品位凹凸棒石(33.67 mg·g~(-1))、高品位海泡石(25.55 mg·g~(-1))、低品位凹凸棒石(11.52 mg·g~(-1))和低品位海泡石(5.24mg·g~(-1));Cd~(2+)在海泡石、凹凸棒石上的吸附受pH值的影响较大,在pH值为2~4时吸附效果最好;凹凸棒石对Cd~(2+)的吸附较为稳定,在3 h时基本达到吸附平衡;在离子强度为0.01 mol·L~(-1)NaNO_3、Cd~(2+)初始浓度为625 mg·L~(-1)、黏土矿物添加量为15 g·L~(-1)和pH值为2~4时,去除效果从大到小依次为高品位海泡石、高品位凹凸棒石、低品位凹凸棒石和低品位海泡石。     

磁性海泡石表面零电荷点和吸附Cd~（2＋）的特性

采用惰性电解质滴定法和静态吸附实验,研究了磁性海泡石表面零电荷点和吸附Cd2＋特性.实验结果表明,海泡石经过磁改性后所对应的pHpzc值由8.0升高到8.5,吸附体系pH的提高,有利于对重金属阳离子Cd2＋的吸附.在pH值大于3时,磁性海泡石对Cd2＋吸附量和去除率随pH值的升高而增大且趋于稳定,其吸附量为16.10 mg.g-1,约为海泡石的3.9倍,去除率为98%,约为海泡石的2.2倍.磁性海泡石对Cd2＋的吸附量与离子强度有较大的相关性,随离子强度的增加而减小;对Cd2＋的吸附量随反应温度的升高而增加,吸附等温式符合Langmuir方程.吸附机理以表面配合吸附和表面沉淀为主.     

热处理富钙海泡石对水体中砷的吸附特征

以富钙海泡石为研究对象,利用简单易行的热处理方法改性,并用X-射线荧光光谱仪(XRF)、X-射线衍射仪(XRD)和扫描电子显微镜(SEM-EDS)对原状和热处理富钙海泡石进行成分和结构分析,研究改性材料对As3+和As5+的吸附特征和影响因素。结果表明,热处理改性显著增加了富钙海泡石对砷的吸附性能,当pH值为7时,对As3+和As5+的最大理论吸附量分别为25.61和30.30 mg·g-1,且吸附等温式符合Langmuir模型;利用吸附动力学方程拟合发现,改性富钙海泡石对As3+动力学吸附符合准二级动力学模型,而对As5+的吸附符合准一级动力学模型和准二级动力学模型。材料粒径对热处理富钙海泡石吸附砷影响较小,当pH值为6~11时,热处理富钙海泡石对砷的吸附影响很小;共存阴离子中PO43-对砷吸附量的影响最大。该研究表明成本较低的热处理富钙海泡石可有效去除废水中的砷。     

根瘤菌S2对离子态和酒石酸络合态铜的吸附行为

探究根瘤菌S2的吸附动力学和热力学行为以及根据不同投菌量和pH的影响分析其对于Cu~(2+)及酒石酸络合铜的吸附性能;结合对吸附前后上清液及菌体进行EEM、FTIR、XRD以及XPS分析解释菌株吸附机理.结果表明,菌株吸附2 mg·L~(-1) Cu~(2+)及酒石酸络合铜均可分为快速吸附和慢速平衡阶段,12 h后基本达到平衡,吸附率达97%以上;温度的升高会导致吸附量增加.最适投菌量约为0.6 g·L~(-1) wet cells;菌株吸附Cu~(2+)的最适pH值为6,而当pH值小于10时菌株对于酒石酸络合铜的吸附几乎不受影响.在吸附过程中,溶解性微生物产物(SMP)、细胞壁上的还原和官能团络合机制均发挥关键作用,吸附铜离子过程中SMP的作用更明显,而细胞壁在络合铜的吸附过程中的作用较大,其破络效率决定于细菌活性.     

不同热解条件下制备的秸秆炭对铜离子的吸附动力学

研究了不同热解条件下制备的秸秆生物炭对铜离子的吸附动力学规律.以常见的玉米杆和番茄杆为原料,在限氧升温热解的条件下制备生物炭.研究不同热解温度(300、400、500、600、700℃)和不同热解时间(1、2、4、6、8 h)对秸秆生物炭吸附性能的影响,实验结果表明番茄杆样品T6004和玉米杆样品C6006分别获得对铜离子的最佳吸附效果,其去除率分别为98.40%和98.77%.通过批试验探明秸秆生物炭对Cu~(2+)的吸附动力学特征与机理,秸秆生物炭对Cu~(2+)的吸附动力学数据随时间的变化能很好地用准二级动力学方程进行拟合,说明生物炭对Cu~(2+)的吸附是一个复杂的过程,并不是简单的单层吸附.用颗粒内扩散模型进行拟合分析发现,热解时间和温度对秸秆生物炭的吸附边界层厚度均会产生不同程度的影响.此外,颗粒内扩散并非吸附过程的唯一控速步骤,表面吸附和液膜扩散共同控制吸附反应速率.     

短乳杆菌对Cr3+的吸附及动力学和热力学拟合

研究了Lactobacillus brevis对水溶液中Cr(Ⅲ)的吸附作用.考察了初始pH值、接触时间、初始Cr(Ⅲ)浓度、菌体浓度和温度对Cr(Ⅲ)吸附效果的影响.结果表明,在较低的pH、温度和初始Cr(Ⅲ)离子浓度条件下,菌株对Cr(Ⅲ)离子的吸附量较低.在试验条件下,溶液初始pH、温度和初始Cr(Ⅲ)离子浓度的升高,均能提高菌株对Cr(Ⅲ)离子的吸附量.在温度为40℃、pH 6和初始Cr(Ⅲ)离子浓度为200 mg·L~(-1)时,菌株吸附量最大.随菌体浓度升高,单位浓度菌体对Cr(Ⅲ)离子吸附量降低,但总吸附量增大,菌体浓度为6 g·L~(-1)吸附量最大.菌株对Cr(Ⅲ)离子吸附较快,接触时间为1 h就达到平衡.用Langmuir、Freundlich、Redlich-Peterson和Temkin吸附模型进行拟合,相关的回归系数表明,吸附过程拟合Langmuir吸附模型比Freundlich、Redlich-Peterson和Temkin吸附模型好.用Elovich、准一级、准二级动力学拟合,动力学试验数据与Lagergren准二级动力学方程的拟合度最佳.     

啤酒酵母去除水中Cd~(2+)和Cu~(2+)的吸附动力学和解吸特性

生物吸附法是一种经济有效的处理大规模低浓度重金属废水的生物技术,其中啤酒酵母(Saccharomyces cerevisiae)是具有实用潜力的生物吸附剂.通过以实验室培养的啤酒酵母作生物吸附剂,研究了啤酒酵母对Cu~(2+)、Cd~(2+)吸附的动力学解吸特性,结果表明:非固定化啤酒酵母对重金属的吸附是一个快速的、不依赖于生物代谢的过程,经过2h后Cd~(2+)达吸附平衡,Cu~(2+)为3 h.它们的吸附动力学过程均可用Elovich方程、抛物线扩散方程、双常数方程、二级动力学方程、Langmuir动力学方程来拟合,对Cd~(2+)来说,以二级动力学方程的拟合效果最佳,Cu~(2+)以Elovich方程最佳.固定化啤酒酵母吸附Cd~(2+)的平衡时间为60 h,Cu~(2+)为24 h,吸附速率大大降低.固定化啤酒酵母对重金属的吸附动力学也可用Elovich方程、抛物线扩散方程、双常数方程、二级动力学方程、Langmuir动力学方程拟合,但Cd~(2+)以Elovich方程最佳,Cu~(2+)以Langmuir动力学方程最佳.固定化碱处理啤酒酵母可用HC1作为解吸剂进行解吸,使吸附剂得到再生,具有较大的开发应用潜力.     

磷酸活化活性炭对Cu2+的吸附特征研究

寻求廉价而高效的吸附材料为目的,研究向日葵秸杆基活性炭对铜离子的吸附性能。以向日葵秸秆为原料,经H3PO4活化制备活性炭,通过静态实验研究了其对水溶液中Cu2+的吸附特性,考察了溶液pH值、吸附温度和离子强度对吸附的影响,探讨了吸附热力学、动力学和吸附机理。结果表明:溶液pH值为5～6时活性炭对Cu2+的去除效果最好;向50 mL 170 mg·L-1的溶液中加入0.5 g活性炭,温度为45℃、吸附时间为1 h时,对Cu2+的去除率可达98.3%;Langmuir方程能更好地描述Cu2+在活性炭上的等温吸附特征,静态吸附容量可达41.03 mg·g-1;吸附过程符合拟二级动力学过程,且为吸热的化学吸附过程,膜扩散为速率控制步骤,离子交换可能在吸附过程中起了重要作用。     

石英砂负载氧化铁吸附除锑的研究

考察了石英砂负载氧化铁(IOCS)在不同的实验条件下(无机阴离子种类及其离子强度、 pH值、IOCS投加量、温度等)对水溶液中锑的去除效果.结果表明:三种无机阴离子(NO-3,Cl-,SO2-4)对IOCS吸附锑的去除率、吸附容量以及反应速率几乎没有影响;在pH3-9范围内,锑的去除率达到90%.二级反应动力学模型及Langmuir等温吸附模型可分别较好地描述锑的吸附动力学及吸附等温线实验结果.随着温度的增加,反应速率以及吸附容量也随之增加.     

Biosorption of chromium(VI), nickel(II) and copper(II) ions from aqueous solutions using Pithophora algae

The biosorption of heavy metals is considered to be one of the best alternatives for the treatment of wastewater. The metal binding capacity of algae and acid-treated algae is investigated to find out the removal characteristics of Cr(VI), Ni(II) and Cu(II) ions from single metal solutions. Batch experiments are conducted and the study is extended to investigate the effect of pH, amount of adsorbent and adsorbate concentration on the extent of biosorption. The results indicate that the adsorption capacity of algae depends strongly on pH. The maximum adsorption of Cr(VI), Ni(II) and Cu(II) occurs at pH values of 2, 7 and 4.3, respectively. The adsorption process follows first-order kinetic equation. The data obtained are correlated with Freundlich and Langmuir adsorption isotherms.     

硅藻土和膨润土对重金属离子Zn~（2＋）、Pb~（2＋）及Cd~（2＋）的吸附特性

以硅藻土和膨润土作为吸附剂,考察微波加热与否条件下,不同吸附时间、不同吸附剂用量和不同pH值对硅藻土和膨润土分别吸附Zn2＋、Pb2＋、Cd2＋重金属离子的影响.实验结果表明,硅藻土和膨润土对3种重金属离子均有很好的吸附效果,吸附时间对去除率影响不大,数分钟即可达到吸附平衡,微波加热、增加吸附剂用量和提高pH值,都有利于提高3种重金属离子的去除率.     

Removal of lead from aqueous solution by hydroxyapatite/manganese dioxide composite

A novel composite adsorbent, hydroxyapatite/manganese dioxide (HAp/MnO₂), has been developed for the purpose of removing lead ions from aqueous solutions. The combination of HAp with MnO₂ is meant to increase its adsorption capacity. Various factors that may affect the adsorption efficiency, including solution pH, coexistent substances such as humic acid and competing cations (Ca²⁺, Mg²⁺), initial solute concentration, and the duration of the reaction, have been investigated. Using this composite adsorbent, solution pH and coexistent calcium or magnesium cations were found to have no significant influence on the removal of lead ions under the experimental conditions. The adsorption equilibrium was described well by the Langmuir isotherm model, and the calculated maximum adsorption capacity was 769 mg·g⁻¹. The sorption processes obeyed the pseudo-second-order kinetics model. The experimental results indicate that HAp/MnO₂ composite may be an effective adsorbent for the removal of lead ions from aqueous solutions.     

花生壳吸附Pb^2＋、Cu^2＋、Cr^3＋、Cd^2＋、Ni^2＋的动力学和热力学研究

以花生壳为生物吸附剂,通过序批式实验研究了吸附剂投量、吸附时间、金属离子初始质量浓度、吸附温度对吸附金属离子的影响,探讨了花生壳吸附的动力学及热力学特性。结果表明,准二级动力学方程能很好地描述花生壳对Pb^2＋、Cu^2＋、Cr^3＋、Cd^2＋、Ni^2＋的吸附过程。Langmuir模型和Freundlich模型均能较好地描述花生壳对5种重金属离子的等温吸附过程,而Langmuir模型拟合的线性更好。Pb2＋、Cu2＋、Cr3＋、Cd2＋、Ni2＋5种金属离子的最大吸附量分别是32.25、7.09、3.82、2.95、2.22 mg.g-1,花生壳可用于处理低质量浓度多种重金属混合的废水。热力学研究表明,花生壳对5种金属离子的吸附具有自发、吸热和熵增的特性。     

Lead(II) and cadmium(II) removal from aqueous solution using processed walnut shell: kinetic and equilibrium study

The biosorption potential of processed walnut shell for Pb(II) and Cd(II) ions from aqueous solutions was explored. The effects of pH, contact time, initial ion concentration, and amount of dried adsorbent were studied in batch experiments. The maximum adsorption was achieved within the pH range 4.0–6.0. The equilibrium data were well fitted by the Langmuir isotherm model. The maximum monolayer adsorption capacities were found to be 32?g?kg^?1 and 11.6?g?kg^?1 for Pb(II) and Cd(II) ions, respectively. Kinetic data were best described by the pseudo-second-order model. The structural features of the adsorbent were characterized by Fourier transform infrared spectroscopy, which confirmed the involvement of hydroxyl (–OH), carboxyl (–COO^–), and carbonyl (C=O) groups in metal sorption. This readily available adsorbent is efficient in the uptake of Pb(II) and Cd(II) ions from an aqueous solution and could be used for the treatment of wastewater streams bearing these metal ions.     

Retention characteristics of Cu2+, Pb2+, and Zn2+ from aqueous solutions by two types of low lime fly ashes

The technical feasibility of utilization of fly ash as a low-cost adsorbent for the removal of metals from water has been studied. For two types of fly ashes, the retention capacities of copper, lead, and zinc metal ions have been studied. Contact time, initial concentration, and pH have been varied and their effect on retention mechanism has been studied. The dominant mechanisms responsible for retention are found to be precipitation due to the presence of calcium hydroxide, and adsorption due to the presence of silica and alumina oxide surfaces in the fly ash. First-order kinetic plots have revealed that the rate constant increases with increase in the initial concentration and pH. Langmuir adsorption isotherms have been plotted to study the maximum adsorption capacities for metal ions considered under different conditions. X-ray diffraction studies revealed the formation of new peaks corresponding to respective metal ions precipitates under alkaline conditions.     

富磷污泥生物炭去除水中Pb(Ⅱ)的特性研究

以城市污水厂富磷剩余污泥为研究对象,考察高温热解制备生物炭吸附剂对水中Pb(Ⅱ)的去除效果.研究表明,随着热解温度升高,制备的生物炭对Pb(Ⅱ)的吸附能力增强;在相同热解温度下,生污泥生物炭对Pb(Ⅱ)的吸附能力比消化污泥生物炭大.采用700℃热解1 h制备生污泥生物炭以研究对Pb(Ⅱ)吸附的影响因素,结果显示:吸附180 min达到吸附平衡;富磷污泥生物炭对Pb(Ⅱ)的去除率随pH增加而升高;生物炭投加量增加,对Pb(Ⅱ)去除率上升,而单位吸附容量迅速减小.污泥生物炭对Pb(Ⅱ)的吸附符合准二级反应动力学,Langmuir模型比Freundlich模型能更好地拟合等温吸附线.在pH 5.0、吸附时间3 h、生物炭投加量20 g.L-1条件下,对Pb(Ⅱ)的最大吸附量为34.5 mg.g-1,表明富磷污泥生物炭可以作为一种廉价的吸附剂.     

Cr (VI) and Fe (III) removal using Cajanus cajan husk

Husk of tur dal (Cajanus cajan) was investigated as a new biosorbent for the removal of Fe (III) and Cr (VI) ions from aqueous solutions. Parameters like agitation time, adsorbent dosage and pH were studied at different initial Fe (III) and Cr (VI) concentrations. The biosorptive capacity of the Tur dal husk was dependent on the pH of the chromium and iron solution, with pH 2 and 2.5 respectively being optimal. The adsorption data fit well with Langmuir and Freundlich isotherm models. The practical limiting adsorption capacity (qmax) calculated from the Langmuir isotherm was 96.05 mg of Cr(VI)/ g of the biosorbent at an initial pH of 2.0 and 66.65 mg/g at pH 2.5. The infrared spectra of the biomass revealed that hydroxyl, carboxyl and amide bonds are involved in the uptake of Cr (VI) and Fe (III) ions. Characterisation of tur dal husk has revealed that it is an excellent material for treating wastewaters containing low concentration of metal ions.     

Comparative adsorption of Pb(II) and Cd(II) ions on chestnut shell in aqueous system

In this study, high capacity Chestnut shell, a waste product from the chestnut sugar production industry, was successfully applied to remove Pb (II) and Cd (II) ions from aqueous solutions. Maximum adsorption capacities were found as 541.25?mg/g and 75.86?mg/g for Pb(II), and Cd(II) respectively. Several important parameters influencing the adsorption of Pb(II) and Cd(II) ions such as contact time, pH, temperature and effect of metal concentration were investigated systematically by batch experiments. Langmuir and Freundlich adsorption models were used to describe adsorption isotherms and constants. The thermodynamic parameters, such as standard free energy (ΔG°), standard enthalpy (ΔH°), and standard entropy (ΔS°), of the adsorption process were calculated. The adsorbents were characterised by scanning electron microscopy. It has been observed from the experimental results that in case of both Cd (II) and Pb (II), pseudo 2nd order kinetic model. From the results, Chestnut Shell are considered as an effective, low cost and environmental friendly adsorbent for the removal of Pb (II) and Cd (II) from wastewater.     

Heavy metals uptake from aqueous solutions using marine algae (Colpomenia sinuosa): kinetics and isotherms

The adsorption of copper, zinc, cobalt, lead and cadmium ions onto Colpomenia sinuosa was studied as a function of contact time, initial metal ion concentration and initial pH. In addition, desorption studies were performed. Characterisation of this adsorbent was also confirmed by Fourier transform infrared (FTIR) spectroscopy and scanning electron microscopy (SEM) analysis. Batch adsorption experimental data were analysed using Langmuir, Freundlich and Dubinin–Raduschkevich (D–R) adsorption isotherms. The results indicated that the biosorption equilibrium was well described by both the Freudlich and D–R isotherms. Moreover, sorption kinetics was performed and it was observed that equilibrium was reached in<60 min, which could be described by the pseudo-second-order kinetic model for all heavy metals. The sorption of heavy metals onto the biomass was largely dependent on the initial solution pH. The elution efficiency for heavy metal ions desorption from C. sinuosa was determined for 0.1 M HCl, 1.0 M HCl and 1.0 M HNO₃. Desorption efficiency and also adsorption capacity were highest for Pb(II). The results indicate that C. sinuosa has great potential for the removal of heavy metals in an ecofriendly process.