Assessment of thermodynamics performance with sustainable propulsion indicators of a seaplane engine for different temperatures in the same altitude

Seaplanes have become an important tool along with rapidly developing technology in modern transportation for many countries related to sea. Considering the environmental evaluation for these aircraft, decreasing fossil fuels consumption and energy efficiency are important points for sustainability. For this purpose, in this study, first, the energy and exergy analyses based on the real data of a turboprop engine used in seaplane taken as the reference were performed. Then, new indicators developed for the sustainable propulsion index were examined and evaluated separately. The analyses were made for an altitude of 9000 ft and three different dead state temperatures of ?33°C, ?3°C, and 27°C. According to the analyses, while the average energy efficiencies were found to be 34.7%, 37.8%, and 40.7%, the average exergy efficiencies were found to be 19.24%, 21.25%, and 23.20%, respectively. In addition, the improvement potential due to irreversibility and entropy production for each case was also calculated and the results of the sustainable emission index were found to be very low. At the end of the study, the results were evaluated and some suggestions for the effective use of energy in the seaplanes were made.     

Comparison of jatropha and karanja biofuels on their combustion characteristics

Biofuel blends produced from Jatropha (Jatropha curcas) and Karanja (Pongamia pinnata) oil were evaluated for their combustion properties. Two kinds of blends (regular diesel with Jatropha and Karanja oil) were prepared at 20% volume to the diesel and tested as alternative fuels in single cylinder (vertical), water-cooled, direct injection diesel engine at the rated speed of 1500 rpm. The performance of the engine in terms of thermal efficiency at full load for diesel was 30%. For Jatropha and Karanja biodiesel blends, the thermal efficiencies were 29.0% and 28.6%, respectively. The maximum cylinder pressure and ignition delay for biodiesel fuel blends are very close to that of regular diesel. Prolonged combustion was observed for Karanja oil blend in comparison to Jatropha oil blend. The combustion pattern also reveals the slow burning characteristics of vegetable oils and this study indicates that the blended biofuels have combustion characteristics that are similar to regular diesel fuels.     

Energy,exergy analysis,and sustainability assessment of different engine powers for helicopter engines

The rapid decrease of energy resources has accelerated studies on energy efficiency. Energy efficiency refers to the effective use of energy, in other words, completing a specific task to the required standard by using less energy. Exergy is an effective instrument to indicate the effective and sustainable use of energy in systems and processes. Transportation is an important part of human life. The studies on energy saving and the effective use of energy in different areas around the world have also increased for transportation systems and vehicles. With the more effective use of fuel, there will be potential benefits for the environment as well as a reduction in operating costs. This study includes energy and exergy analyses as well as a sustainability assessment by using C₈H₁₆ as a fuel at different engine powers (150–600 SHP (shaft horse power)), for the piston-prop helicopter engine. The maximum exergetic sustainability index was found at the power that provided the maximum energy and exergy efficiency. As a result of this index, the lowest waste exergy ratio, the lowest exergy destruction factor, and the lowest environmental impact factor were obtained. The highest exergy destruction and the highest exergy loss value were obtained at maximum power (600 SHP).     

Exergetic Sustainability Indicators as a Tool in Commercial Aircraft: A Case Study for a Turbofan Engine

This paper focuses on the exergetic sustainability indicators of a medium-range commercial aircraft engine for constant reference environment and ground running conditions. First, a detailed exergy analysis of turbofan engine have been performed based on engine test cell parameters. Starting from the sustainability considerations and the second law of the thermodynamics, the paper presents six exergy-based sustainability indicators. The indicators of the turbofan engine developed here in conjunction with exergetic analysis and sustainable development are exergy efficiency, waste exergy ratio, exergy destruction factor, recoverable exergy rate, environmental effect factor, and exergetic sustainability index. The investigated sustainable indicators have been calculated by using exergy analysis outputs for aircraft ground running condition. Results from this study show that values of exergy efficiency, waste exergy ratio, exergy destruction factor, recoverable exergy rate, environmental effect factor, and exergetic sustainability index of investigated turbofan engine are found to be 0.315, 0.685, 0.408, 0, 2.174, and 0.460, respectively. These parameters are expected to quantify how the turbofan engine and aircraft become more environmentally benign and sustainable.     

Investigation effect of hydrogen addition on the performance and exhaust emissions of Pongamia pinnata biodiesel fueled compression ignition engine

In the recent decades, the energy demand for transport and industrial sector has increased considerably. Fossil fuels which were the major fuel source for decades are no more sustainable. Biodiesel is an efficient alternative compared to depleting fossil fuels. The prospect of biodiesel as the best alternative fuel is a reliable source compared to depleting fossil fuels. Hydrogen is also considered as an attractive alternative fuel producing low emission with improved engine performance. This paper investigates the performance and emission characteristics of a single cylinder compression ignition engine using hydrogen as an inducted fuel and biodiesel, aka Pongamia pinnata as injected fuel. The experiments are conducted for different quantities of hydrogen induction through the intake manifold in order to improve the performance of the engine. The performance parameters such as brake thermal efficiency, brake specific fuel consumption, exhaust temperature and emission quantities like HC, NO_X, CO, CO₂ of biodiesel fueled CI engine with variable mass flow rate of hydrogen are investigated. The performances of biodiesel combined with hydrogen at varying mass flow rates are also compared. The 10 LPM hydrogen induction with biodiesel provided 0.33% increase of brake thermal efficiency compared with diesel and increase of 3.24% to biodiesel at 80% loading conditions. The emission of HC decreased by 13 ppm, CO decreased by 0.02% by volume and CO₂ decreased by 3.8% by volume for biodiesel with induction of hydrogen at 10 LPM to that of neat biodiesel for 80% load conditions.     

Energy and exergy analysis of a solid-oxide fuel cell power generation system for an aerial vehicle (ISSA- 2015–139)

This paper presents the performance of the solid-oxide fuel cell/gas turbine hybrid power generation system with heat recovery waste unit based on the energy and exergy analyses. The effect of air inlet temperature and air/fuel ratio on exergy destruction and network output is determined. For the numerical calculations, air inlet temperature and air fuel ratio are increased from 273 to 373 K and from 40 to 60, respectively. The results of the numerical calculations bring out that total exergy destruction quantity increases with the increase of air inlet temperature and air/fuel ratio. Furthermore, the maximum system overall first and second law efficiencies are obtained in the cases of air inlet temperature and air/fuel ratio equal to 273 K and 60, respectively, and these values are 62.09% and 54.91%.     

Exergoeconomic Environmental Optimization of Piston-Prop Aircraft Engines

In this study, exergy, exergoeconomic, exergoenvironmental analyses, and exergoeconomic environmental optimization are applied to a four-cylinder, spark ignition, naturally aspirated and air-cooled piston-prop aircraft engine in the cruise phase of flight for the first time to the best of the authors` knowledge. Here, three piston-prop aircraft engine parameters (altitude, air–fuel ratio (AF), and rated power setting (PS)) are selected for optimization purposes. All exergy, exergoeconomic, and exergoenvironmental values are calculated first. These values are then optimized to find the best results of all analyses. The best altitude, AF ratio, and PS values are finally found while the maximum exergy efficiency, the minimum product specific environmental impact, and the minimum average unit fuel exergy cost are obtained. The best results of optimization indicated that the maximum exergy efficiency varied between 19.54% and 19.80%, the minimum unit fuel exergy cost ranged from 126.30 $/GJ to 127.23 $/GJ, and the minimum specific environmental impact of production was in the range of 8.70–9.59 mPts/MJ. Based on the results obtained, for ensuring the optimum conditions, the low AF ratios and the low-altitude flight at high rated power settings have to be selected.     

Experimental investigation of performance and emission characteristics of diesel engine using Jatropha biodiesel with alumina nanoparticles

Biodiesels have come up as a very strong alternative for diesel fuel. Biodiesels such as Jatropha Oil Methyl Ester (JOME) are comparable in performance with that of the diesel engine. The thermal efficiency of engines fuelled with biodiesels was found lower than conventional diesel fuel but due to the bio-origin, the emission characteristics are much better. However, biodiesel increases the NOx emissions as these are rich in oxygen, hence nanoparticles are used in this experiment to curb the high temperatures and reduce the NOx formation. The experiment on naturally aspired diesel engine was conducted with four prepared test fuels other than neat diesel and neat biodiesel. The 50 and 150 of alumina nanoparticles were added separately to the pure diesel and pure Jatropha biodiesel to form the nano emulsions using ultrasonicator. The properties of nanoemulsion were evaluated using dynamic light scattering technique using zetasizer. The performance and emission characteristics of multi-cylinder diesel engine with these nanoemulsions were compared with that of neat fuels. The results showed that using nanoparticles with diesel and biodiesel can contribute in a more efficient, economical, and eco-friendly engine operation.     

Factorial analysis of diesel engine performance using different types of biofuels

In this study, several bio-source-fuels like fresh and waste vegetable oil and waste animal fat were tested at different injector pressures (120, 140, 190, 210 bar) in a direct-injection, naturally aspirated, single-cylinder diesel engine with a design injection pressure of 190 bar. Using 2k factorial analysis, the effect of injection pressure (Pi) and fuel type on three engine parameters, namely, combustion efficiency (etac), mass fuel consumption (mf), and engine speed (N) was examined. It was found that Pi and fuel type significantly affected both etac and mf while they had a slight effect on engine speed. Moreover, with diesel and biodiesels, the etac increased to a maximum at 190 bar but declined at the higher Pi value. In contrast, higher Pi had a favorable effect on etac over the whole Pi range with all the other more viscous fuels tested. In addition, the mass fuel consumption consistently decreased with an increase in Pi for all the fuels including the baseline diesel fuel, with which the engine consistently attained higher etac and higher rpm compared to all the other fuels tested.     

Phase behaviors,fuel properties,and combustion characteristics of alcohol-vegetable oil-diesel microemulsion fuels

Biofuels are being considered as alternatives to fossil-based fuels due to depletion of petroleum-based reserves and pollutant emission concerns. Vegetable oils and bioalcohols have proven to be viable alternative fuels both with and without engine modification. However, high viscosity and low energy content are long-term operational problems with vegetable oils and bioalcohols, respectively. Therefore, vegetable oil-based microemulsification is being evaluated as a method to reduce the high viscosity of vegetable oils and enhance the miscibility of alcohol and oil phases. Studies have shown that microemulsification with different alcohols lead to varying fuel properties depending on their structure. The overall goal of this study was to formulate microemulsion fuels with single and mixed alcohol systems by determining the effects of water content, alcohol branching structure and carbon chain length on phase behaviors, fuel properties, and emission characteristics. It was found that microemulsion fuels using certain alcohols displayed favorable stability, properties, and emission characteristics. Flames of fuels with linear short-chain-length alcohols had larger near-burner blue regions and lower CO and soot emissions indicating the occurrence of more complete combustion. In addition to alcohol effects, the effect of vegetable oils, surfactants, and additives on emission characteristics were insightful in pursuit of appropriate microemulsion fuels as cleaner burning alternatives to both No.2 diesel and canola biodiesel.     

Usability of food industry waste oils as fuel for diesel engines

Two cogeneration units were each fitted with a prechamber (IDI) diesel engine in order to test the feasibility of using waste oils from the food industry as a fuel source, and additionally to test emissions generated by the combustion of these fuels. Esterified waste oils and animal fats as well as mustard oil were tested and compared to the more or less "common" fuels: diesel, rapeseed oil and rapeseed methyl ester. The results show that, in principle, each of these fuels is suitable for use in a prechamber diesel engine. Engine performance can be maintained at a constant level. Without catalytic conversion, the nitrogen oxides emissions were comparable. A significant reduction in NO(x) was achieved through the injection of urea. Combining a urea injection with the SCR catalytic converter reduced NO(x) emissions between 53% and 67%. The carbon monoxide emissions from waste oils are not significantly different from those of "common" fuels and can be reduced the same way as of hydrocarbon emissions, through utilization of a catalytic converter. The rate of carbon monoxide reduction by catalytic conversion was 84-86%. A lower hydrocarbon concentration was associated with fuels of agricultural origin. With the catalytic converter a reduction of 29-42% achieved. Each prechamber diesel engine exhibited its own characteristic exhaust, which was independent of fuel type. The selective catalytic reduction of the exhaust emissions can be realized without restriction using fuels of agricultural origin.     

An experimental apparatus for testing biodiesels based on a CFR engine—setup and validation with different methyl ester blends

A cooperative fuel research (CFR) engine was modified and instrumented in order to control operating conditions and to measure engine parameters and in-cylinder pressure diagrams. Aiming at the comparison of different alternative fuels, an experimental procedure was defined, including cetane number (CN) evaluation and the definition of engine operating quantities in different working points, for fixed levels of compression ratio (CR) and injection advance. An investigation was made considering several blends of methyl-esters of rapeseed oil (RME) and of a mix of vegetable oils (VOME) with conventional diesel oil. The defined experimental procedure was applied to assess CN, engine brake thermal efficiency (bte) and exhaust emissions. Results show that the biodiesel content has a positive influence on soot emissions, with strong reduction, while thermal efficiency and NO_X emissions are negatively affected, which can be justified taking into account fuel properties and changes in combustion process. As observed outcomes are generally in line with those presented in literature, the facility proved to be a suitable tool for basic investigations on alternative fuels to be used in specific applications.     

A Parametric Study of a Piston-Prop Aircraft Engine Using Exergy and Exergoeconomic Analysis Methods

In this study, exergetic and exergoeconomic analysis methods are applied to a four-cylinder, spark ignition (SI), naturally aspirated and air-cooled piston-prop aircraft engine in the cruise phase of flight operations. The duration of cruise is selected to be 1 h. Three parameters, altitude, rated power setting (PS), and air-to-fuel ratio (AF), are varied by the calculation of the max–min values of exergy analysis. Based on the results of energy analysis, the values for the maximum energy efficiency and fuel consumption flow rate are calculated to be 21.73% and 28.02 kg/h, respectively, at 1000-m altitude and 75% PS. The results of exergy analysis indicate that all exergetic values vary from 65% to 75% PS, while this increase is not seen in exergoeconomic analysis. While the maximum exergy input rate is obtained to be 405.60 kW, exergy efficiency has the minimum value with 14.43% and exergy destruction rate has the maximum value with 168.48 kW. These values are achieved at 3000-m altitude and 18 AFs. The maximum average exergy cost of the fuel is calculated to be 130.77 $/GJ at 1000-m altitude, 13 AF ratios, and 65% PS. At this point, while the minimum cost rate associated with the exergy destruction is obtained to be 40.29 $/h, the maximum exergoeconomic factor is found to be 19.98%.     

Performance assessment of integrated energy systems for HVAC applications

In this article, energy and exergy analyses are conducted for two integrated systems which can be used in HVAC applications. These two systems are analyzed for the cases of single generation, cogeneration and trigeneration, and their performances are evaluated through energy and exergy efficiencies. The parametric studies are performed to investigate the effects of using cogeneration and extended to trigeneration on the system performance. To perform the comparisons between the systems for multiple options, the same amounts of outputs (in terms of electricity, heating, cooling) are produced for all systems. The energy analyses of systems 1 and 2 show a great benefit for moving from single generation to trigeneration, with the trigeneration efficiencies of 83.5% and 87.2%, respectively, and single generation efficiencies of 47% for both systems. However, the exergy analyses show that trigeneration may not always become more efficient than single generation, particularly for system 1, due to the fact that the trigeneration exergy efficiency is 38.7% and the corresponding single generation efficiency is 44.3%. For system 2, the trigeneration exergy efficiency is 52.7% while the single generation efficiency becomes 44.3%. Depending on the type of cogeneration or cogeneration design, the system can be more efficient.     

Selection of optimum fish oil fuel blend to reduce the greenhouse gas emissions in an IC engine—A hybrid multiple criteria decision aid approach

The increasing demand on energy due to population growth and rising of living standards has led to considerable use of fossil fuels which has in turn, had an adverse impact on environmental pollution and depletion of fossil fuels in Internal Combustion (IC) engine sector. Alternative fuel blend evaluation in IC engine fuel technologies is a very important strategic decision involving decisions balancing within a number of criteria and opinions from different decision maker of IC engine experts. The selection of appropriate source of biodiesel and proper blending of biodiesel plays a major role in alternate energy production. This paper describes an application of hybrid Multi Criteria Decision Making (MCDM) technique for the selection of optimum biodiesel blend in the IC engine. The proposed model, Analytical Network Process (ANP) is integrated with Technique for Order Performance by Similarity to Ideal Solution (TOPSIS) to evaluate the optimum blend. Here the ANP is used to determine the relative weights of the criteria, whereas TOPSIS is used for obtaining the final ranking of alternative blends. An efficient pair-wise comparison process and ranking of alternatives can be achieved for optimum blend selection through the integration of ANP and TOPSIS. The obtained preference order for the blends are as B20 > B40 > Diesel > B60 > B80 > B100. This paper highlights a new insight into MCDM techniques to evaluate the best fuel blend for the decision makers such as engine manufactures and R&D engineers to meet the fuel economy and emission norms to empower the green revolution.     

Investigation of sustainable energy alternatives for powering remote communities in northern Ontario

ABSTRACT

Remote communities in the North of Ontario survive in isolation as their proximity to the southern industrial sector of the province limits their accessibility to the major grid. The lack of grid connection has led to antiquated methods of power generation which pollute the environment and deplete the planet of its natural resources. Aside from the primary means of electricity generation being by diesel generators, generation infrastructure is deteriorating due to age and the stagnation of the power supply has led to communities facing load restrictions. These challenges may be resolved by introducing clean energy alternatives and providing a fuel blend option. The primary energy sources investigated in this research are solar, wind, and hydrogen. To assess the viability of these energy production methods in Northern communities, an exergy analysis is employed as it utilizes both the first and second law of thermodynamics to determine systems’ efficiency and performance in the surroundings. Local weather patterns were used to determine the viability of using wind turbines, solar panels and/or hydrogen fuel cells in a remote community. Through analysis of the resources available at the community, it was determined that the hydrogen fuel cell was best suited to provide clean energy to the community. Wind resulted in low efficiency in the range of 2–3% while solar efficiencies resulted in ranges of 18 – 19%, as the seasonal variations between the three years is not very great. Due to the higher operating efficiencies observed of the PV panels it would also be an attractive alternative to diesel generators however, the lack of consistent operation above 30% efficiency throughout the year, resulted in hydrogen fuel cells being a better alternative.     

Performance analysis of bioethanol (Water Hyacinth) on diesel engine

The increasing consumption and excessive extraction of conventional fuels is the matter of serious concern. Nowadays, world is looking for alternative sources of fuel which can partially replace conventional fuel dependence. The current investigation intends to provide evaluation of bio-ethanol preparation from Water Hyacinth (WH) and its influence on diesel engine performance under various operating conditions. This study explores the extraction of glucose from WH (Eichhornia crassipes) pretreated with sulfuric acid (H₂SO₄) for production of bio-ethanol. For the production of bio-ethanol different concentrations of H₂SO₄ acid hydrolysate (1%, 2%, 4%, 6%, 8%, and 10%) were prepared which was then followed by fermentation with cellulose fermenting yeasts. From results, it was observed that 4% H₂SO₄ acid hydrolysis produces higher concentrations of ethanol than other concentrations. Bio-ethanol extracted from WH was blended with diesel in different proportions (5%, 10%, 15%, 20%, and 25%) v/v and performance and emissions were experimentally investigated on single cylinder diesel engine under various load conditions. Experimental results show that 5 BED [5% bio-ethanol (WH + 95%diesel v/v) and 10BED (10% bio-ethanol (WH + 90%diesel v/v)] produces higher brake power, brake thermal efficiency and brake mean effective pressure with improved exhaust emission profiles than any other blend.     

Ignition advancement study for optimized characteristics of a raw biogas operated spark ignition engine

In the current investigation, raw biogas obtained from rural sectors was used as the alternative to gasoline fuel in the spark ignition (SI) engine. The performance and efficiency are mainly dependent on the combustion phasing for which “ignition timing” is an effective tool in a SI engine. Hence, the objective of the present work is to understand the effect of “variable ignition timing” for a biogas-fueled SI engine. For this purpose, a single cylinder, 4-stroke, SI engine of rated power 4.5 kW was operated with raw biogas at a compression ratio (CR) of 10. By maintaining a speed of 1650 rpm, the engine was operated in wide open (WOT) and part throttle (PT) mode with an equivalence ratio of 0.81 and 0.83, respectively. It was observed that the biogas fueled SI engine was found to be operative only within the ignition advance (IA) range of 33–47° CA bTDC both in WOT and PT conditions. The results showed optimal brake power (BP), brake thermal efficiency (BTE) and brake specific fuel consumption (BSFC) are achieved at 45° CA bTDC. The average peak cylinder pressure, neat heat release rate (NHRR) and mean gas temperature (MGT) are also observed to be maximum while CO and HC emission at this point of IA were found to be minimum. Due to controlled and complete combustion, CO₂ and NO_x concentration in the exhaust emission were found to be higher at this point of ignition timing.     

Alternative energy: Environmental and economic factors associated with renewable energy and creating new integrated energy management systems

At best, the future of alternative and renewable energy remains uncertain. Our dependency on fossil fuels is already depleting world supplies of coal and petroleum while increasing greenhouse gas emissions. Most assuredly, the ability of alternative energy, described in this article as biomass, hydrogen, wind, solar, and geothermal power, to compete and even integrate with fossil fuels will depend on several important variables: First, developing, as well as developed, countries must be willing to direct long-term public and private funding towards innovative energy technologies by increasing research and promoting public education. Secondly, the “bottom line” economics associated with alternative energy technology must clearly show a positive cost/benefit ratio. Revenues and not deficits are paramount to the sustainability of alternative energy. Lastly, many experts argue for the environmental benefits of alternative energy by way of carbon reductions. The 1997 Kyoto Global Warming Treaty requires the United States in particular to reduce carbon dioxide emissions from fossil fuel burning by 7 percent below 1990 levels. While many experts argue that reactions to global warming and the alternative energy benefits anticipated because of them are fiscally irresponsible and not worth the billions of tax dollars intended, we can be assured that a business-as-usual attitude will continue without increased government and public support.© 1999 John Wiley & Sons, Inc.     

A Novel Solar Thermal Cycle with Chemical Looping Combustion

In this paper, we have proposed a thermal cycle with the integration of chemical-looping combustion and solar thermal energy with the temperature of about 500-600°C. Chemical-looping combustion may be carried out in two successive reactions between a reduction of hydrocarbon fuel with metal oxides and a reduced metal with oxygen in the air. This loop of chemical reactions is substituted for conventional combustion of fuel. Methane as a fuel and nickel oxides as an oxygen carrier were employed in this cycle. Collected high-temperature solar thermal energy is provided for the endothermic reduction reaction. The feature of the proposed cycle is investigated through Energy-Utilization Diagram methodology. As a result, at the turbine inlet temperature of 1200°C, the exergy efficiency of the proposed cycle would be expected to be about 4 percentage points higher than that of a conventional gas turbine combined cycle. Compared to the previous study of chemical-looping combustion energy systems, the proposed cycle with the integration of green energy and traditional hydrocarbon fuels will offer the possibility of both greenhouse gas mitigation, with green energy, and a new approach to the efficient use of solar energy.