Conversion of Concentrated Solar Thermal Energy into Chemical Energy

When a concentrated solar beam is irradiated to the ceramics such as Ni-ferrite, the high-energy flux in the range of 1500–2500 kW/m² is absorbed by an excess Frenkel defect formation. This non-equilibrium state defect is generated not by heating at a low heating-rate (30 K/min), but by irradiating high flux energy of concentrated solar beam rapidly at a high heating rate (200 K/min). The defect can be spontaneously converted to chemical energy of a cation-excess spinel structure (reduced-oxide form) at the temperature around 1773 K. Thus, the O₂ releasing reaction (α-O₂ releasing reaction) proceeds in two-steps; (1) high flux energy of concentrated solar beam absorption by formation of the non-equilibrium Frenkel defect and (2) the O₂ gas formation from the O^2? in the Frenkel defect even in air atmosphere. The 2nd step proceeds without the solar radiation. We may say that the 1st step is light reaction, and 2nd step, dark reaction, just like in photosynthesis process.     

Fresnel lens to concentrate solar energy for the photocatalytic decoloration and mineralization of orange II in aqueous solution

The decoloration and mineralization of the azo dye orange II under conditions of artificial ultraviolet light and solar energy concentrated by a Fresnel lens in the presence of hydrogen peroxide and TiO(2)-P25 was studied. A comparative study to demonstrate the viability of this solar installation was done to establish if the concentration reached in the focus of the Fresnel lens was enough to improve the photocatalytic degradation reaction. The degradation efficiency was higher when the photolysis was carried out under concentrated solar energy irradiation as compared to UV light source in the presence of an electron acceptor such us H(2)O(2) and the catalyst TiO(2). The effect of hydrogen peroxide, pH and catalyst concentration was also determined. The increase of H(2)O(2) concentration until a critical value (14.7 mM) increased both the solar and artificial UV oxidation reaction rate by generating hydroxyl radicals and inhibiting the (e(-)/h(+)) pair recombination, but the excess of hydrogen peroxide decreases the oxidation rate acting as a radical or hole scavenger and reacting with TiO(2) to form peroxo-compounds, contributing to the inhibition of the reaction. The use of the response surface methodology allowed to fit the optimal values of the parameters pH and catalyst concentration leading to the total solar degradation of orange II. The optimal pH range was 4.5-5.5 close to the zero point charge of TiO(2) depending on surface charge of catalyst and dye ionization state. Dosage of catalyst higher than 1.1 gl(-1) decreases the degradation efficiency due to a decrease of light penetration.     

Effect of the carbon coating in Fe-C-TiO(2) photocatalyst on phenol decomposition under UV irradiation via photo-Fenton process

Fe-C-TiO(2) photocatalysts which contained the residue carbon (0.2-3.3 mass%) were prepared from a mixture of TiO(2) and FeC(2)O(4) through the heating at 673-1173 K in Ar. These photocatalysts did not show a high adsorption of phenol, but they were active in photo-Fenton reactions during decomposition of phenol under UV irradiation with addition of H(2)O(2). It was proved that Fe(2+) governed the photoactivity of Fe-C-TiO(2) photocatalysts, it decreased with heat-treatment temperature above 773 K. For comparison, Fe-TiO(2) photocatalyst was prepared by heating TiO(2) and FeC(2)O(4) at 823 K in air for 3h. Phenol decomposition was going much slower on Fe-TiO(2) photocatalyst in comparison with Fe-C-TiO(2), of which mechanism was different, on the former phenol was decomposed by the radical reaction, on the latter through a complex reaction with iron and intermediates of phenol decomposition. Therefore carbon-coating TiO(2) was found to be advantageous for mounting iron and its application for the phenol decomposition via photo-Fenton process.     

Dechlorination of PCBs in the simulative transformer oil by microwave-hydrothermal reaction with zero-valent iron involved

The conventional hydrothermal reaction with iron powder, NaOH and H₂O as reactants was reported to occur at temperature above 423 K, and iron oxides (Fe₃O₄ and NaFeO₂) and hydrogen were produced. In this study, microwave heating was adopted to take the place of conventional heating to induce the hydrothermal reaction. Under microwave irradiation, NaOH and H₂O absorbed microwave energy by space charge polarization and dipolar polarization and instantly converted it into thermal energy, which initiated the hydrothermal reaction that involved with zero-valent iron. X-ray diffraction (XRD) analysis found Fe₃O₄/NaFeO₂ and confirmed the occurrence of microwave-induced hydrothermal reaction. The developed microwave-hydrothermal reaction was employed for the dechlorination of PCBs. Hexadecane containing 100 mg L⁻¹ of Aroclor1254 was used as simulative transformer oil, and the dechlorination of PCBs was evaluated by GC/ECD, GC/MS and ion chromatography. For PCBs in 10 mL simulative transformer oil, almost complete dechlorination was achieved by 750 W microwave irradiation for 10 min, with 0.3 g iron powder, 0.3 g NaOH and 0.6 mL H₂O added. The effects of important factors including microwave power and the amounts of reactants added, on the dechlorination degree were investigated, moreover, the dechlorination mechanism was suggested. Microwave irradiation combined with the common and cheap materials, iron powder, NaOH and H₂O, might provide a fast and cost-effective method for the treatment of PCBs-containing wastes.     

Thermal detoxification of hazardous metal sludge by applied electromagnetic energy

Industrial wastewater sludge was treated by microwave processes to enhance the stabilization of laden copper. The effects of additives, processing time, microwave adsorbents, moisture content, reaction atmosphere, and cooling gas were investigated. The stabilization results were significantly enhanced by metal powder additives, prolonged microwave processing time, proper moisture content, the addition of carbonaceous materials, and a reaction environment with inert gas. It was also found that the moisture content would increase the homogeneity of applied microwave energy, and thus achieve a better overall efficiency between stabilizing agents and copper. The added metal powders may reduce Cu(II) to Cu(0) in the sludge or TCLP. The resulting thermal energy of microwave radiation, and microarcing process and the oxidation heat of Al powder may also assist the transformation of Cu(II) into CuO and CuAl2O4 phases. Part of the sludge was vitrified within inert gas environment when the processing time was longer than 18 min and active carbon dosage was more than 3g. Reduction reactions also occurred in the hybrid microwave processes, leading to the reduction of sulfates and metal ions, and the formation of Cu2S and FeS. Moreover, the microwave radiation can also enhance the feasibility of co-treating of inorganic and organic solid waste.     

Oxidation of elemental mercury using atmospheric pressure non-thermal plasma

The oxidation of gas phase elemental mercury (Hg0) by atmospheric pressure non-thermal plasma has been investigated at room temperature, employing both dielectric barrier discharge (DBD) of the gas mixture of Hg0 and injection of ozone (O3) into the gas mixture of Hg0. Results have shown that the oxidative efficiencies of Hg0 by DBD and the injection of O3 are 59% and 93%, respectively, with energy consumption of 23.7 J L(-1). This combined approach has indicated that O3 plays a decisive role in the oxidation of gas phase Hg0. Also the oxidation of Hg0 by injecting O3 into the gas mixture of Hg0 proceeds with better efficiency than DBD of the gas mixture of Hg0. These results have been explained by the incorporation of the competitive reaction pathways between the formation of HgO by O3 and the decomposition of HgO back to Hg0 in the plasma environment.     

Temperature dependence of hydroxyl radical formation in the hv/Fe3+/H2O2 and Fe3+/H2O2 systems

The thermal enhancement of the formation of *OH by the hv/Fe(III)/H2O2 system (including the Fe(III)/H2O2 system) was quantitatively investigated with reaction temperatures ranging from 25 to 50 degrees C. A temperature dependent kinetic model for the hv/Fe(III)/H2O2 system, incorporating 12 major reactions with no fitted rate constants or activation energies, was developed, and successfully explained the experimental measurements. Particularly, the thermal enhancement of Fe(OH)2+ photolysis which is the most significant step in the hv/Fe(III)/H2O2 system was effectively explained by two factors; (1) the variation of the Fe(OH)2+ concentration with temperature, and (2) the temperature dependence of the quantum yield for Fe(OH)2+ photolysis (measured activation energy=11.4 kJ mol(-1)). Although in both the hv/Fe(III)/H2O2 and Fe(III)/H2O2 systems, elevated temperatures enhanced the formation of *OH, the thermal enhancement was much higher in the dark Fe(III)/H2O2 system than the hv/Fe(III)/H2O2 system. Furthermore, it was found that the relative thermal enhancement of the formation of *OH in the presence of *OH scavengers (tert-butyl alcohol) was magnified in the Fe(III)/H2O2 system but was not in the hv/Fe(III)/H2O2 system.     

Destruction of EDTA using Ce(IV) mediated electrochemical oxidation: a simple modeling study and experimental verification

Mediated electrochemical oxidation (MEO) is a recent development in the environmental research field for the complete destruction of organic pollutants. This study presents the destruction of EDTA by cerium(IV) MEO process in nitric acid medium. The destruction reaction was carried out in a continuous stirred tank reactor under various conditions. A simple kinetic model was developed to analyze and simulate the organic destruction in the MEO process. The model was based on the calculation of the total mass balance, the component mass balance, and the energy balance in the reactor and also in the heating jacket. The sensitivity to key operating conditions such as the initial EDTA concentration (50-200 mM), EDTA feeding time (30-180 min), reaction temperature (323-363 K), and the rate laws corresponding to zero-, first-, second-, and third-order reaction were analyzed. It was found that the model simulated agreed well with the experimental data for EDTA oxidation. The results obtained showed the suitability of the MEO process for the effective mineralization of high concentrations of EDTA.     

Microwave pretreatment for enhancement of phosphorus release from dairy manure

Both the advanced oxidation process (AOP) using a combination of hydrogen peroxide addition and microwave heating (H2O2/microwave), and the microwave heating process were used for solubilization of phosphorus from liquid dairy manure. About 80% of total phosphate was released into the solution at a microwave heating time of 5 min at 170 degrees C. With an addition of H2O2, more than 81% of total phosphate could be released over a reaction period of 49 h at ambient temperature. The AOP process could achieve up to 85% of total phosphate release at 120 degrees C. The results indicated that both the microwave, and the AOP processes could effectively release phosphate from liquid dairy manure. These processes could serve as pretreatments for phosphorus recovery from animal wastes, and could be combined with the struvite crystallization process to provide a new approach in treating animal wastes.     

K2Cr2O7溶液同时脱硫脱硝实验研究

采用K2Cr2O7溶液作为吸收液,在自制的鼓泡反应器内,对模拟烟气进行同时脱硫脱硝的实验研究,考察多种因素对SO2脱除率(即脱硫率)和NO脱除率(即脱硝率)的影响。实验结果表明:K2Cr2O7浓度、反应温度、NO浓度、SO2浓度、烟气流量对脱硫率、脱硝率影响显著;当烟气流量为0.4L/min,气相中O2体积分数为6%,SO2体积分数为0.09%,NO体积分数为0.100%,K2Cr2O7摩尔浓度为10mmol/L,反应温度为40℃时,脱硫率、脱硝率分别达到100%和64.3%。     

Nanofluid heat transfer under mixed convection flow in a tube for solar thermal energy applications

The solar flat plate collector operating under different convective modes has low efficiency for energy conversion. The energy absorbed by the working fluid in the collector system and its heat transfer characteristics vary with solar insolation and mass flow rate. The performance of the system is improved by reducing the losses from the collector. Various passive methods have been devised to aid energy absorption by the working fluid. Also, working fluids are modified using nanoparticles to improve the thermal properties of the fluid. In the present work, simulation and experimental studies are undertaken for pipe flow at constant heat flux boundary condition in the mixed convection mode. The working fluid at low Reynolds number in the mixed laminar flow range is undertaken with water in thermosyphon mode for different inclination angles of the tube. Local and average coefficients are determined experimentally and compared with theoretical values for water-based Al₂O₃ nanofluids. The results show an enhancement in heat transfer in the experimental range with Rayleigh number at higher inclinations of the collector tube for water and nanofluids.     

The energy balance of central Mexico City during the dry season

The first measurements of the energy balance fluxes of a dry, densely built-up, central city site are presented. Direct observation of the net radiation, sensible and latent heat flux densities above roof-top in the old city district of Mexico City allow the heat storage flux density to be found by residual. The most important finding is that during daytime, when evaporation is very small (<4% of net radiation), and therefore sensible heat uses dominate (Bowen ratio >8), the uptake of heat by the buildings and substrate is so large (58%) that convective heating of the atmosphere is reduced to a smaller role than expected (38%). The nocturnal release of heat from storage is equal to or larger than the net radiation and sufficient to maintain an upward convective heat flux throughout most nights. It is important to see if this pattern is repeated at other central city, or dry urban sites, or whether it is only found in districts dominated by massive stone structures. These findings have implications for the height of the urban mixing layer and the magnitude of the urban heat island.     

The calcination process in a system for washing, calcinating, and converting treated municipal solid waste incinerator fly ash into raw material for the cement industry

Calcination is the second step in a washing-calcination-conversion system in which treated municipal solid waste incinerator fly ash and bottom ash can be reused as raw material in the cement industry and can decompose or stabilize hazardous compounds, reduce residue amounts, and alter residue characteristics. In this research, only fly ash is discussed. Chloride reduction is important if treated fly ash is to be reused in cement; however, the relationship between washed fly ash properties and chloride reduction by calcination is not well understood. This study used washed residues of three types of fly ash-raw fly ash (RFA) from the boiler or economizer of an incineration system, fly ash collected in a bag filter injected with calcium hydroxide (Ca(OH)2) for acid removal (CaFA), and fly ash collected in a bag filter injected with sodium bicarbonate (NaHCO3) for acid removal (NaFA)-in calcination experiments with varying temperature (400-1100 degrees C) and atmosphere (100% nitrogen [N2] at 25 mL/min or 10% oxygen [O2] [90% N2] at fluxes of 25, 50, and 75 mL/min). From the perspective of chloride reduction, heating to 1000 degrees C with 1-hr heating time, 1-hr holding time, and an atmosphere of 10% O2/90% N2 was most suitable for calcination. Under these conditions, chloride levels were reduced by 91, 52, and 96% in washed residues of RFA, CaFA, and NaFA, respectively. Among the washed residues, the weight of the washed residue of NaFA decreased the most.     

Photocatalytic removal of fenitrothion in pure and natural waters by photo-Fenton reaction

The photocatalytic removal kinetics of fenitrothion at a concentration of 0.5mgl(-1) in pure and natural waters were investigated in Fe(III)/H2O2/UV-Vis, Fe(III)/UV-Vis and H2O2/UV-Vis oxidation systems, with respect to decreases in fenitrothion concentrations with irradiation time using a solar simulator. Fenitrothion concentrations were determined by HPLC analysis. Furthermore, total mineralization of fenitrothion in these systems was evaluated by monitoring the decreases in DOC concentrations with solar simulator irradiation time by TOC analysis. It was shown that the degradation rate of fenitrothion was much faster in the Fe(III)/H2O2/UV-Vis system than the Fe(III)/UV-Vis and H2O2/UV-Vis systems in both pure and river waters. Consequently, the mineralization rate of fenitrothion was much faster in the Fe(III)/H2O2/UV-Vis system than in the other two systems. The high *OH generation rate measured in the Fe(III)/H2O2/UV-Vis system was the key to faster degradation of fenitrothion. Increases in the concentrations of H2O2 and Fe led to better final degradation of fenitrothion. These results suggest that the photo-Fenton reaction (Fe(III)/H2O2/UV-Vis) system is likely to be an effective method for removing fenitrothion from contaminated natural waters.     

Simultaneous removal of NO and SO2 by high-temperature fluidized zero-valent iron processes

A new approach to simultaneously remove nitrogen monoxide (NO) and sulfur dioxide (SO2) by zero valent iron (ZVI) was investigated. Three different parameters, temperature, flux, and ZVI dosage, were tested in fluidized ZVI column studies containing 500 ppmv of NO and SO2, respectively. Under the ZVI dosage of 0.5 g at flux of 0.6 L/cm2 x min for temperature 573 K, there is neither NO nor SO2 reduction. For 623 K and 673 K, complete removal for NO and > 90% removal for SO2 were achieved. For temperatures of 723 K and 773 K, 100% removal was achieved for both NO and SO2. The amounts of NO or SO2 reduction (as milligrams of NO or SO2 per gram ZVI) increased as temperature increased, and linearities were observed with both correlation coefficients > 0.97. Compared with NO, SO2 had earlier breakthrough because of a slower diffusion rate and less reactivity but higher mass reduction because of a higher molecular weight for SO2 (64 g/mol for SO2 and 30 g/mol for NO). At same temperature, both NO and SO2 reductions (as milligrams of NO or SO2 per gram of ZVI) were constant regardless of either flux or ZVI dosage variation, but breakthrough time was affected by both flux and ZVI dosage. A parameter weight of ZVI/flux (W/F) was developed to represent these two parameters at the same time to assess the breakthrough time of NO and SO2. Higher breakthrough time was achieved for higher W/F value. Moreover, interestingly, longer breakthrough time and more NO and SO2 mass reduction were achieved for combined NO and SO2 than individual NO or SO2 treated by ZVI, and both oxidation and reduction reactions occurred instead of a reduction reaction only. Chemical reactions among ZVI/NO, ZVI/ SO2, and ZVI/NO/SO2 were also proposed and verified by X-ray diffraction analyses.     

Highly concentrated phenolic wastewater treatment by the photo-Fenton reaction, mechanism study by FTIR-ATR

Phenol degradation by Photo-Fenton reaction has been studied in highly concentrated wastewaters and most intermediate species have been identified by Fourier Transform IR-Spectroscopy with ATR device. During the photodegradation of highly concentrated phenol solutions, the formation of dissolved and precipitate tannin has been observed. The possibility of a Fe3+-Pyrogallol complex formation, previous to the tannin formation, has been proposed too. The complex formation involving Fe3+ ions could be related to the observed Photo-Fenton activity decrease. Tannin formation inhibits the complete mineralization of phenol because *OH radicals attack will produce further condensation steps and the polymer size increase. This fact limits the applicability of the process for highly concentrated phenolic wastes mineralization. However, the tannin precipitation allows its separation from the solution by conventional filtration, and reduction of the corresponding dissolved organic carbon. These observations have been proved from the identification of primary degradation products, catechol and hydroquinone. Catechol is considered to be the first step for the formation of tannins. Degradation process for phenol, catechol and hydroquinone have been monitored by total organic carbon (TOC) measurements along the reaction time span. From these results, a global mechanism for the Photo-Fenton degradation of phenol is proposed.     

Hydrogen peroxide-assisted UV photodegradation of Lindane

Aqueous solutions of gamma-hexachlorocyclohexane (Lindane) were photolyzed (lambda=254 nm) under a variety of solution conditions. The initial concentrations of hydrogen peroxide (H(2)O(2)) and Lindane varied from 0 to 20 mM and 0.21 to 0.22 microM, respectively, the pH ranged from 3 to 11, and several concentration ratios of Suwannee River humic acid and fulvic acid were dissolved in the irradiated solutions. Lindane rapidly reacted, and the maximum reaction rate constant (9.7 x 10(-3) s(-1)) was observed at pH 7 and initial [H(2)O(2)]=1 mM. Thus, 90% of the Lindane is destroyed in approximately 4 min under these conditions. In addition, within 15 min, all chlorine atoms were converted to chloride ion, indicating that chlorinated organic by-products do not accumulate. The reactor was characterized by measuring the photon flux (7.04 x 10(-6) E s(-1)) and the cumulative production of *OH during irradiation. The cumulative *OH production during irradiation was fastest at an initial [H(2)O(2)]=5 mM (k=0.77 micro M s(-1)).     

Coupled solar photo-Fenton and biological treatment for the degradation of diuron and linuron herbicides at pilot scale

A coupled solar photo-Fenton (chemical) and biological treatment has been used to remove biorecalcitrant diuron (42 mg l(-1)) and linuron (75 mg l(-1)) herbicides from water at pilot plant scale. The chemical process has been carried out in a 82 l solar pilot plant made up by four compound parabolic collector units, and it was followed by a biological treatment performed in a 40 l sequencing batch reactor. Two Fe(II) doses (2 and 5 mg l(-1)) and sequential additions of H2O2 (20 mg l(-1)) have been used to chemically degrade the initially polluted effluent. Next, biodegradability at different oxidation states has been assessed by means of BOD/COD ratio. A reagent dose of Fe=5 mg l(-1) and H2O2=100 mg l(-1) has been required to obtain a biodegradable effluent after 100 min of irradiation time. Finally, the organic content of the photo-treated solution has been completely assimilated by a biomass consortium in the sequencing batch reactor using a total suspended solids concentration of 0.2 g l(-1) and a hydraulic retention time of 24h. Comparison between the data obtained at pilot plant scale (specially the one corresponding to the chemical step) and previously published data from a similar system performing at laboratory scale, has been carried out.     

Photo-oxidation of cork manufacturing wastewater

Several photo-activated processes have been investigated for oxidation of a cork manufacturing wastewater. A comparative activity study is made between different homogeneous (H2O2/UV-Vis and H2O2/Fe2+/UV-Vis) and heterogeneous (TiO2/UV-Vis and TiO2/H2O2/UV-Vis) systems, with degradation performances being evaluated in terms of total organic carbon (TOC) removal. Results obtained in a batch photo-reactor show that photo-catalysis with TiO2 is not suitable for this kind of wastewater while the H2O2/UV-Vis oxidation process, for which the effect of some operating conditions was investigated, allows to remove 39% of TOC after 4 h of operation (for C(H2O2)=0.59 M, pH=10 and T=35 degrees C). The combined photo-activated process, i.e., using both TiO2 and H2O2, yields an overall TOC decrease of 46% (for C(TiO2)=1.0 gl(-1)). The photo-Fenton process proved to be the most efficient, proceeds at a much higher oxidation rate and allows to achieve 66% mineralization in just 10 min of reaction time (for C(H2O2)=0.31 M, T=30 degrees C, Fe2+:H2O2=0.12 (mol) and pH=3.2).     

Effect of sulfur dioxide and sulfite on photochemical energy storage of isolated chloroplasts--a photoacoustic study

Photoacoustic spectroscopy was used to study the effect of sulfite and SO(2) on isolated corn mesophyll chloroplasts by monitoring the photochemical energy storage. Sulfite incubation of isolated chloroplasts, either in light or in darkness, caused a decrease in photochemical energy storage. The more pronounced decrease in light indicates a light-dependent sulfite inhibitory site(s) in chloroplasts. Also diphenylcarbazide caused a partial recovery of energy storage in sulfite treated chloroplasts indicating a possible site of damage at the water oxidizing system. Although the chloroplast membranes were found to be insensitive to high concentrations of SO(2) for relatively short exposure periods (10 min) in light, exposure of chloroplasts to 28.5 ng cm(-3) SO(2) for 10 min caused a decrease in energy storage. An attempt was made to explain the mechanism of action of sulfite and SO(2) in chloroplasts.