Preparation and characterization of mesoporous γ-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> recovered from aluminum cans waste and its use in the dehydration of methanol to dimethyl ether

The present study includes synthesis of two γ-Al₂O₃ samples from waste aluminum cans using a simple precipitation method. Precipitation was carried out using two different precipitating agents (i.e. NaOH and NH₄OH). The two prepared alumina samples were characterized by means of X-ray diffraction (XRD) and N₂ adsorption–desorption techniques. Surface acidity of γ-Al₂O₃ samples was measured by adsorption of two different probe molecules (i.e. pyridine and dimethyl pyridine) followed by desorption measurements using thermogravimetry (TG) and differential scanning calorimetry (DSC) techniques. Catalytic activity of the two prepared alumina samples towards the dehydration of methanol (to dimethyl ether) was studied in a fixed bed reactor at 300 °C. For comparison reasons, commercial γ-Al₂O₃ sample was, also, tested for the same catalytic reaction under the same conditions. Results showed that the alumina sample prepared using NaOH as a precipitating agent exhibited a better catalytic activity and stability compared with that prepared using NH₄OH and showed a similar activity as the commercial γ-Al₂O₃ sample.     

Reductive decomposition of waste gypsum with SiO<Subscript>2</Subscript>, Al<Subscript>2</Subscript>O<Subscript>3</Subscript>, and Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> additives

From the point of view of a sustainable and environment-friendly society based on the recycling of material resources, it is preferable to utilize waste gypsum as a substitute for lime, which is currently produced by the calcination of limestone. In the present work, the reductive decomposition of CaSO₄ was investigated under an atmosphere of CO: 2 vol%, CO₂: 30 vol%, with N₂ as a carrier gas without and with the addition of SiO₂, Al₂O₃, or Fe₂O₃. It was found that the decomposition temperature of CaSO₄ was significantly reduced from 1673 K to 1223 K when only 5 wt% Fe₂O₃ was added to CaSO₄. In the case of the addition of SiO₂ or Al₂O₃ to CaSO₄, the decomposition temperature was reduced from 1673 K to 1623 K. This was due to the formation of composite oxides (calcium ferrite, calcium silicate, or calcium aluminate) during the reaction of CaSO₄ with the additives at a lower temperature. In addition, the formation of unfavorable product CaS was inhibited in the presence of 5 wt% Fe₂O₃, and this inhibition effect further increased as the addition of Fe₂O₃ was increased. In contrast, no significant effect on the inhibition of CaS formation was observed on the addition of SiO₂ or Al₂O₃.     

Whole-year-round Observation of N<Subscript>2</Subscript>O Profiles in Soil: A Lysimeter Study

Despite many studies of the N₂O emission, there is a lack of knowledge on the role of subsoil for N₂O emission, particularly in sandy soils. To obtain insight into the entrapment, diffusion, convection and ebullition of N₂O in the soil, the N₂O concentration in the soil atmosphere was measured over a period of 1 year in 4 lysimeters (agricultural soil monoliths of 1 m2 × 2 m) at 30, 50, 80, 155, and 190 cm depth with altogether 86 gas probes. Additionally the N₂O emission into the atmosphere was measured in 20 closed chambers at the soil surface. Concurrently the soil temperature and soil water content were recorded in order to quantify their effects on the fate of N₂O in the soil. Results of the continuous measurements between January and December 2006 were: N₂O concentrations were highest in the deeper soil; maximum concentration was found at a depth of 80 cm, where the water content was high and the gas transport reduced. The highest N₂O concentration was recorded after ‘special events’ like snowmelt, heavy rain, fertilization, and grubbing. The combination of fertilization and heavy rain led to an increase of up to 2,700 ppb in the subsoil.     

Study on desulfurization performance of MnO<Subscript>2</Subscript>-based activated carbon from waste coconut shell for diesel emissions control

Increasing concern about the air pollution caused by sulfur dioxide (SO₂) from diesel exhaust has resulted in the improvement of low-temperature desulfurization materials for the combined SO₂ trap. In this study, coconut shell activated carbon (AC) is pretreated by nitric acid to prepare MnO₂-based activated carbon materials for SO₂ removal. The prepared materials are characterized intensively by SEM, TEM, BET, XRD, FTIR, and XPS. The SO₂ capture capacity of these materials are measured at low temperature by thermogravimetry, and the SO₂ equilibrium adsorption characteristic is also investigated. The results show that the concentrations of nitric acid do not significantly change the textural properties of MnO₂-based AC materials. The content of surface-oxygenated groups (carbonyl carbon and transition) initially increases with the HNO₃ concentration rising and reaches the maximum value when the HNO₃ concentration is 10 mol/L, resulting in the enhancement of the SO₂ capture capacity. SO₂ capture capacity of MnO₂-based activated carbon decreases after regeneration and keeps stable after several cycles of thermal regeneration. The experimental data for SO₂ adsorption on MnO₂-based AC composite can fit the Freundlich model well in comparison with Langmuir model.     

Effect of Nanoscale SiO<Subscript>2</Subscript> and TiO<Subscript>2</Subscript> as the Fillers on the Mechanical Properties and Aging Behavior of Linear Low-Density Polyethylene/Low-Density Polyethylene Blends

Linear low-density polyethylene (LLDPE) was blended with low-density polyethylene (LDPE) at a fixed ratio (80 wt LLDPE and 20 wt %LDPE) and filled with nanoparticles of SiO₂ and TiO₂ at a ratio up to wt 5%, so as to develop the polymeric composites suitable to preparing the agricultural micro-irrigation pipes having good environmental adaptability. These compounds were blended using calcium stearate, polyethylene wax, and titanate coupling agent as the auxiliary dispersants, and ethylene-vinyl acetate copolymer (EVA) as the toughness improver. The LLDPE/LDPE composites filled with the nanoparticles were extruded and injected to prepare the composites specimens for the performance evaluations and micro-irrigation pipe field test. The mechanical properties, thermostability, and processibility of the injected composites were investigated. The effect of heating in an oven and irradiating by ultraviolet on the mechanical properties of the composites was explored. The environmental adaptability of the micro-irrigation pipes made of the filled LLDPE/LDPE composites was evaluated making use of long-term outdoor field test in northwest China where the arid and harsh natural conditions are of great concerns. It was found that the LLDPE/LDPE blend with the LLDPE mass fraction fixed as 80% showed balanced mechanical and thermal properties and flexibility, and was suitable to be used as the basic resin matrix. The incorporation of nano-TiO₂ contributed to effectively improving the resistance to heating and ultraviolet irradiation of the composites. The composite made from 91% basic resin matrix, 6% EVA, and 3% mixed nano-SiO₂ and TiO₂, showed balanced comprehensive properties. The micro-irrigation pipes made of this filled LLDPE/LDPE composite had good environmental adaptability and service behavior in a three-year field test and were suitable to be used in arid area.     

Photochemical Degradation of Aqueous Polyvinyl Alcohol in a Continuous UV/H<Subscript>2</Subscript>O<Subscript>2</Subscript> Process: Experimental and Statistical Analysis

Polyvinyl alcohol (PVA), being a dominant contributor of total organic carbon (TOC) in textile wastewater, is not easily degradable by conventional methods of wastewater treatment. This study investigates the degradation of aqueous PVA in a continuous UV/H₂O₂ photoreactor since the feeding strategy of hydrogen peroxide proves to have considerable effects on the process performance. Response surface methodology involving the Box–Behnken method is adopted for the experimental design to study the effects of operating parameters on the process performance. Experimental analysis shows that the TOC removal varies from 16.11 to 42.70 % along with a reduction of the PVA molecular weights from 56.7 to 95.3 %. The TOC removal is significantly lower than the molecular weight reduction due to the generation of the intermediate products during oxidation. Operating the UV/H₂O₂ process in a continuous mode facilitates the degradation of highly concentrated polymeric solutions using a relatively small hydrogen peroxide concentration in the feed with a small residence time ranges from 6.13 to 18.4 min.     

Effect of ZnCl<Subscript>2</Subscript> impregnation ratio on pore structure of activated carbons prepared from cattle manure compost: application of N<Subscript>2</Subscript> adsorption-desorption isotherms

Activated carbons were prepared from cattle manure compost (CMC) by ZnCl₂ activation with various ZnCl₂/CMC mass ratios. Based on the N₂ adsorption-desorption isotherms, mathematical models including the Dubinin-Radushkevich (DR) equation, the α_s plot, and the Horvath-Kawazoe method were used to analyze the pore structural characteristics of the prepared activated carbons. It was found that for carbons possessing both micro-and mesopores, the DR method provided a more accurate estimation than the α_s method for the extent of microporosity. The effect of the ZnCl₂ impregnation ratio on the pore structure was discussed using the DR method. The results revealed that pore evolution involved three distinct regions with increases in the amount of impregnated ZnCl₂: raising the ZnCl₂/CMC mass ratio from 0.00 to 0.50 resulted in a 19-fold increase in micropore volume (V_me ^D) but caused no change in the mesopore volume (V_me ^D); increasing the ZnCl₂/CMC mass ratio from 0.50 to 1.00 led to an increment in V_mi ^D of about 50% and in V_me ^D of 170%; while raising the ratio from 1.50 to 2.50 caused a slight decrease in V_mi ^D but a 200% increment in the value of V_me ^D.     

Influence of H<Subscript>2</Subscript> on the decomposition of halides by nonthermal plasma incorporated with in situ alkaline absorption

To control the emission of halides into the environment, an experiment on the nonthermal plasma decomposition of the halides CF₄, CHF₃, C₂HCl₃, and CHClF₂ was conducted in a wire-in-tube corona reactor. It was found that the decomposition of C₂HCl₃ and CHClF₂ was easy compared with the decomposition of CF₄ and CHF₃. With the addition of H₂ in N₂ gas, the decomposition ratio of CF₄, C₂HCl₃, and CHClF₂ increased. In contrast, the decomposition ratio of CHF₃ in a hydrogen-rich atmosphere was lower than that in an N₂ atmosphere. It was demonstrated that the yields of HF and/or HCl formed during halide decomposition clearly increased in the presence of H₂ in N₂ gas. Furthermore, in order to prevent the production of unwanted products from halide decomposition, a combination of plasma decomposition and in situ alkaline absorption was devised by coating a layer of Ca(OH)₂ onto the surface of the grounding electrode. It was demonstrated that the Ca(OH)₂ sorbent played an effective role as a scavenger, participating in halide decomposition by capturing reaction products such as HCl and HF, therefore resulting in increased halide decomposition.     

Selective catalytic reduction of NO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> using RDF char and municipal solid waste char based catalyst

Experiments were performed in order to investigate the possibility for the development of catalysts for low-temperature selective catalytic reduction (SCR) using municipal waste char and RDF byproduct. Physical and chemical activations, using water, and HCl and KOH, were employed to increase the catalytic activities. The characteristics of the activated catalysts were investigated using N₂ adsorption–desorption and FT-IR. The catalysts activated chemically using basic treatment showed higher NO _x removal efficiencies than those activated physically or chemically using acidic treatment. The de-NO _x performance of the activated catalysts was dependent on the chemical properties, such as oxygen functional groups as well as physical properties, such as specific surface area and pore volume. In order to investigate the effect of MnO _x , which has been reported to be efficient for the removal of NO _x in low-temperature SCR processes, the chemically activated catalyst was impregnated with manganese. The Mn-impregnated catalyst had the highest NO _x conversion at all of the temperatures tested in this study.     

High Toughness and Fast Crystallization Poly(Lactic Acid)/Polyamide 11/SiO<Subscript>2</Subscript> Composites

A poly(lactic acid) (PLA)/polyamide 11 (PA11)/SiO₂ composite was mixed from PLA, PA11, and nanosilica particles through twin-screw extrusion. The PLA/PA11/SiO₂ composite was evaluated with tensile and Izod impact tests, light transmission and haze measurement, and isothermal and nonisothermal crystallization behavior determinations. The PLA/PA11/SiO₂ (97.0/3.0) composite had approximately 10.8% less ultimate tensile strength than neat PLA, but it had greater ductility and approximately ninefold greater elongation at break. A dimple morphology was observed on the fractural surface of the PLA/PA11/SiO₂ composite, indicating that the incorporation of PA11 and nanosilica particles increased the ductility of the PLA matrix. PLA with less than 3 wt% of PA11 and 0.5 phr of nanosilica particles had an Izod impact strength of 8.72 kJ/m². PA11 and nanosilica particles effectively toughened this PLA polymer; they accelerated both isothermal and nonisothermal crystallization rates and increased the crystallinities of the resulting composites under isothermal and nonisothermal crystallization processes.     

Preparation of Water-Insoluble Antibacterial Materials with Surface-Grafted Material PSt/SiO<Subscript>2</Subscript> and Their Antibacterial Activity

Styrene (St) was graft-polymerized onto the surfaces of micro-sized silica gel particles, and the surface-grafted composite particles PSt/SiO₂ were obtained. With the surface-grafted composite particles PSt/SiO₂ as a starting material, water-insoluble antibacterial materials with quaternary ‘onium’ salt-type were synthesized via two polymer reaction steps. The grafted polystyrene was first chloromethylated, resulting in grafted particles CMPS/SiO₂, and then quaterisation (QN) and quaternary phosphonium reaction (QP) were conducted with triethylamine, tri-n-butylamine and triphenyl phosphine as reagents, respectively. Two kinds of water-insoluble antibacterial materials, QN-PSt/SiO₂ and QP-PSt/SiO₂ were prepared. Their antibacterial property was mainly investigated by using Escherichia coli (E. coli) as a model bacterium and by adopting colony count method. The relationship between the chemical structure of the antibacterial group and antimicrobial activity for the water-insoluble antibacterial materials was studied in detail, and their antibacterial mechanism was investigated by TTC-dehydrogenase activity determination and extracellular DNA and RNA measurement methods. The experimental results show that QN-PSt/SiO₂ and QP-PSt/SiO₂ possess strong antibacterial activity. The main factors affecting the antibacterial ability of the water-insoluble materials are the chemical structure of the antibacterial groups, the bound density of the antibacterial groups on the surface of the water-insoluble antibacterial materials as well as the pH value of the medium. QP-PSt/SiO₂ has stronger antibacterial activity than QN-PSt/SiO₂; the QN-PSt/SiO₂ prepared with tri-n-butylamine has stronger antibacterial activity than that prepared with triethylamine; the water-insoluble material with higher bound density of the antibacterial groups has stronger antibacterial ability; as the pH value of the medium is over the isoelectric point of E. coli, the antibacterial ability is strengthened with the increase of pH value.     

Green Synthesis of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>/Cellulose/Polyvinyl Alcohol Hybride Aerogel and Its Application for Dye Removal

A novel Fe₃O₄/cellulose–polyvinyl alcohol (PVA) aerogel was successfully synthesized by an eco-friendly and facile method in this work. Cellulose/PVA matrix was prepared through an environmental friendly physical cross-linking process and further in-situ decorated with Fe₃O₄. Series of Fe₃O₄ decorated aerogels were prepared and the effects of Fe₃O₄ nanoparticles (NPs) on the aerogels were systematic investigated. As-prepared aerogels exhibited desirable properties including nanostructure, relatively high porosity, improved mechanical and superparamagnetism. The TEM results showed that Fe₃O₄ NPs were integrated in the three-dimensional matrix of cellulose/PVA with a diameter of 9–12 nm. Furthermore, the mechanical strength of the aerogels was significantly enhanced after the introduction of Fe₃O₄ NPs. Meanwhile, the obtained Fe₃O₄/cellulose/PVA aerogel exhibited excellent adsorption performance toward methyl blue dye, and can be reused through fenton-like catalysts oxidative degradation of organic dye in H₂O₂ solution. Therefore, they will have a great potential application as eco-friendly and economical adsorbents.     

Preparation of MgCr<Subscript>2</Subscript>O<Subscript>4</Subscript> from waste tannery solution and effect of sulfate,chloride, and calcium on leachability of chromium

This paper presents a study regarding the preparation of MgCr₂O₄ from waste tannery solution, and chromium leaching behavior is also investigated with varying amounts of sulfate, chloride and calcium. The phase transformation, crystallinity index and crystallite diameter were characterized using XRD, FT-IR and thermal analysis. A well-crystallized MgCr₂O₄ was successfully prepared at 1400 °C. The sintering temperature had a major impact on the formation of MgCr₂O₄ compared with sintering time. The MgCr₂O₄ phase was observed initially at 400 °C and its crystallite diameter increased with increasing temperature. The concentration of total chromium leached and Cr(VI) decreased gradually with increasing temperature. The considerable amount of Cr(VI) was found in the leachate at 300–500 °C caused by Cr(VI) intermediary products. Sulfate and chlorine could impact the transformation efficiency of chromium adversely, and chlorine has a more significant effect than sulfate. The presence of calcium disturbed the formation of MgCr₂O₄ and new chromium species (CaCrO₄) appeared, which resulted in a sharp increase in the concentration of leached Cr(VI). Incorporating Cr(III) into the MgCr₂O₄ spinel for reusable products reduced its mobility significantly. This was demonstrated to be a promising strategy for the disposal of chromium containing waste resource.     

Photochemical Kinetic Modeling of Degradation of Aqueous Polyvinyl Alcohol in a UV/H<Subscript>2</Subscript>O<Subscript>2</Subscript> Photoreactor

This study presents a photochemical kinetics model to describe the degradation of water-soluble PVA (Polyvinyl Alcohol) polymer in a UV/H₂O₂ batch reactor. Under the effect of UV light, the photolysis of hydrogen peroxide into hydroxyl radicals can generate a series of polymer scission reactions. For a better understanding and analysis of the UV/H₂O₂ process in the cracking of the PVA macromolecules, a chemical reaction mechanism of the degradation process and a relevant photochemical kinetics model are developed to describe the disintegration of the polymer chains. Taking into account the probabilistic fragmentation of the polymer, the statistical moment approach is used to model the molar population balance of live and dead polymer chains. The model predicts the PVA molecular weight reduction, the acidity of the solution, and hydrogen peroxide residual. In addition to previously published data collected in this laboratory, a new set of experiments were conducted using a 500 mg/L PVA aqueous for different hydrogen peroxide/PVA ratios for model validation. Measurements of average molecular weights of the polymer, hydrogen peroxide concentrations and pH of the PVA solution were determinant factors in constructing a reliable photochemical model of the UV/H₂O₂ process. Experimental data showed a decrease in the PVA molecular weight and a buildup of the solution acidity. The experimental data also served to determine the kinetics rate constants of the PVA photochemical degradation and validate the model whose predictions are in good agreement with data. The model can provide a comprehensive understanding of the impact of the design and operational variables.     

Biodegradable Composite Foams of PLA and PHBV Using Subcritical CO<Subscript>2</Subscript>

One key strategy for increasing the application potential for biodegradable plastics lies in improving the physical and mechanical characteristics, which can be attained by inducing a cellular morphology in the pure polymer with the aid of a blowing agent, as well as by blending two or more polymers with the desirable properties. This paper examines the effect that blending two biodegradable polymers has on the thermal properties and morphology of the resultant foams blown with carbon dioxide (CO₂). Polylactic acid (PLA), polyhydroxybutyrate-co-valerate (PHBV) and blends of both were foamed and characterized in terms of thermal characteristics, relative density, cell size, and foam morphology. The results indicate that although PLA and PHBV are immiscible, the presence of small quantities of PHBV (25 wt%) could lead to low density foams with finer, more uniform cells. Furthermore, the crystallinity of PHBV was found to be unaffected by the presence of PLA in the composite, which supports the immiscibility of PLA and PHBV.     

Long Term Trends in Concentration of Major Pollutants (SO<Subscript>2</Subscript>, CO,NO, NO<Subscript>2</Subscript>, O<Subscript>3</Subscript> and PM<Subscript>10</Subscript>) in Prague – Czech Republic (Analysis of Data Between 1992 and 2005)

To assess the effect of changes in traffic density and fuels used for heating at the beginning of the 1990s, 1992–2005 monthly averages of PM₁₀, SO₂, NO₂, NO, CO and O₃ from Prague, the Czech capital, were analyzed together with long term trends in emissions of major pollutants, fuel consumption and number of vehicles registered in Prague. The data from all monitoring stations were retrieved from the database of the state automated monitoring system. Correlation coefficients between ambient monthly averaged temperature and all pollutants of concern showed distinct seasonal trends. The results showed that while SO₂ and to some extent also CO concentrations dropped namely in the first half of the analyzed period (1992–1997) as a result decreased fossil fuel consumption for local heating, the behaviour of other pollutant concentrations followed a different pattern. PM₁₀ concentrations decreased during the beginning of the 1990s but showed a sign of increase after 2000. Concentrations of ozone and NO₂ did not reveal any significant change throughout the whole studied period. It can be concluded that during the studied period traditional urban sources of pollution, such as coal and oil combustion, lost their importance but were simultaneously substituted by pollutants from automotive transport (namely PM and NO₂) making the problem of air quality even worse.     

Preparation and characterization of high surface area activated carbon from pine wood sawdust by fast activation with H<Subscript>3</Subscript>PO<Subscript>4</Subscript> in a spouted bed

Activated carbons were produced from waste pine wood sawdust using fast activation with H₃PO₄ in a spouted bed. In this study, activation temperature was set as 800 °C, and activation time ranged from 1 to 15 min. Experimental results show that sawdust impregnated with higher mass ratio of H₃PO₄ would be agglomerated in spouted bed, and difficult to fluidize. Therefore, an amount of quartz sand was added to assist for good fluidization. Fluidization of particle can improve the BET surface area or micropore volume of activated carbons. High BET surface area activated carbons can be obtained with activation time of only 1–5 min by combining the fluidization and H₃PO₄ fast activation. The obtained activated carbons contained developed pore structure and abundant surface functional groups (carboxyl, carbonyl and P-containing groups) by SEM–EDS, FTIR and XPS techniques. The particles of impregnation ratio of 1:1 can achieve fluidization without adding the quartz sand, which was convenient for experimental operation and even industrial production, and the BET surface area can reach more than 1000 m²/g in activation time of only 5 min.     

Effect of Nano-SiO<Subscript>2</Subscript> and Bark Flour Content on the Physical and Mechanical Properties of Wood–Plastic Composites

The aim of this study is to evaluate the impact of nano-SiO₂ and bark flour (BF) on the natural fiber–plastic composites engineering properties made from high density polyethylene (HDPE) and beech wood flour (WF). For this purpose, WF and BF in 60 mesh size and weight ratio of (50, 0 %), (30, 20 %), (10, 40 %) and (0, 50 %) respectively were mixed with HDPE. In order to increase the interfacial adhesion between the filler and the matrix, the maleic anhydride grafted polyethylene was constantly used at 3 wt% for all formulations as a coupling agent. The nano-SiO₂ particles with weight ratio of 0, 1, 2, and 4 % were also utilized to enhance the composites properties. The materials were mixed in an internal mixer (HAAKE) and then the bark and/or wood–plastic composite samples were made utilizing an injection molding machine. The physical tests including water absorption and thickness swelling, and mechanical tests including bending characteristics and un-notched impact strength were carried out on the samples based on ASTM standard. The results indicated that as the BF content increased in the composite, mechanical and physical properties were reduced, but the given properties were increased with the addition of nano-SiO₂. The addition of nano-SiO₂ had a negative impact on the physical properties, but when it was up to 2 %, it increased the impact strength.     

Fabrication of Biodegradable Superabsorbent Using RSM Design for Controlled Release of KNO<Subscript>3</Subscript>

Present study envisaged the sequential experimental design approach for the development of biodegradable Gelatin-Tapoica/polyacrylamide superabsorbent. Percentage water uptake efficacy of candidate sample was optimized using Response Surface Methodology (RSM) design under microwave irradiation. Different process variables such as potassium persulphate and ammonium persulphate (KPS:APS) ratio, pH, reaction time concentration of acrylamide and N,N-methylene-bis-acrylamide (MBA) were investigated as a function of percentage swelling using sequential experimental design. Maximum liquid efficacy of 1550% was obtained at KPS:APS?=?1.0:0.5; acrylamide?=?7.67?×?10^?1 mol L^?1; MBA?=?1.76?×?10^?2 mol L^?1; pH 10 and time?=?110 s. The 3D crosslinked network formed was characterized using Fourier Transformation Infrared spectroscopy (FTIR), X-ray diffraction (XRD), Scanning Electron Microscopic (SEM) techniques and thermal stability was ensured by Thermal gravimetric Analysis/Differential Thermal Analysis/Differential Thermal Gravimetric (TGA/DTA/DTG) studies. Superabsorbent synthesized could increase the moisture content in different type of soils and was found to enhance the water-holding capability of the soil upto 60 days in clayey, 40 days in sandy and 51 days in mixture of two soils under controlled conditions. Further, candidate polymer was investigated for the in-vitro controlled release of the KNO₃ with diffusion exponent ‘n’ was found to be 0.4326 indicating Fickian type diffusion. Also, initial diffusion coefficient (D_I?=?3.49?×?10^?5 m² h^?1) was found to be greater than the lateral diffusion coefficient (D_L?=?3.76?×?10^?6 m² h^?1) indicated rapid release of KNO₃ during initial hours with slow release afterwards. The ecofriendly nature of the synthesized polymer was also tested by conducting biodegradation studies and it was found to degrade upto 94% and 88.1% within 70 days with degradation rate of 1.34 and 1.26% per day using composting method and vermicomposting method respectively. So, the synthesized candidate polymer was found to be boon for agriculture-horticulture sector with wide applicability.     

The influence of atmospheric n deposition on nitrous oxide and nitric oxide fluxes and soil ammonium and nitrate concentrations

The deposition of atmospheric N to soils provides sources of available N to the nitrifying and denitrifying microbial community and subsequently influences the rate of NO and N₂O emissions from soil. We have investigated the influence of three different sources of enhanced N deposition on NO and N₂O emissions 1) elevated NH₃ deposition to woodlands downwind of poultry and pig farms, 2) increased wet cloud and occult N deposition to upland forest and moorland and 3) enhanced N deposition to trees as NO^? ₃ and NH⁺ ₄ aerosol. Flux measurements of NO and N₂O were made using static chambers in the field or intact and repacked soil cores in the laboratory and determination of N₂O by gas chromatography and of NO by chemiluminescence analysis. Rates of N deposition to our study sites were derived from modelled estimates of N deposition, NH₃ concentrations measured by passive diffusion and inference from measurements of the ²¹⁰Pb inventory of soils under tree canopies compared with open grassland. NO and N₂O emissions and KCl-extractable soil NH⁺ ₄ and NO^? ₃ concentrations all increased with increasing N deposition rate. The extent of increase did not appear to be influenced by the chemical form of the N deposited. Systems dominated by dry-deposited NH₃ downwind of intensive livestock farms or wet-deposited NH⁺ ₄and NO^? ₃ in the upland regions of Britain resulted in approximately the same linear response. Emissions of NO and N₂O from these soils increased with both N deposition and KCl extractable NH⁺ ₄, but the relationship between NH⁺ ₄ and N deposition (ln NH⁺ ₄ = 0.62 ln N_deposition+0.21, r ² = 0.33, n = 43) was more robust than the relationship between N deposition and soil NO and N₂O fluxes.