从6-APA和7-ADCA生产废液中回收苯乙酸

采用溶剂萃取、水法提取等方法从6-氨基青霉烷酸和7-氨基-3-去乙酰氧基头孢烷酸生产废液（简称废液）中回收苯乙酸（PAA）,考察了各种因素对回收效果的影响。实验结果表明：以甲苯为萃取剂,在萃取温度30℃、萃取时间15m in、500mL废液中萃取剂加入量130mL的最佳条件下,萃取率为96.5%;在提取温度为65℃左右、结晶温度低于10℃的条件下,PAA收率大于89%,纯度大于99%;所得PAA产品质量好,可用于青霉素G等医药产品的生产。     

从含铅锌烟尘中综合回收铅和锌

采用碱浸出—电解工艺综合回收含铅锌烟尘中的铅和锌。实验结果表明,用NaOH溶液浸出的最佳条件为:浸出温度70℃,NaOH溶液体积(mL)与烟尘质量(g)比11,NaOH浓度5 mol/L,浸出时间30 min。在最佳条件下,铅和锌的浸出率均大于90%。浸出液过滤后滤液电解回收铅,电解过程电流效率为86%,直流电耗为660 kW·h(以每吨阴极铅计),铅纯度大于等于95%。电解铅后溶液经净化后,溶液中的铅、铜和铁几乎可全部去除,并去除部分的钨、锡和锑。电解锌过程电流效率为85%,直流电耗为2 500 kW·h(以每吨阴极锌计),锌纯度大于等于97%。     

混合二元酸中戊二酸的分离提纯

采用溶剂溶解和气泡结晶的方法从混合二元酸中分离、提纯戊二酸。考察了溶解温度、溶剂用量和结晶过程对戊二酸纯度和收率的影响 ,并确定了分离与提纯的最佳工艺条件。分离过程 :溶解温度 5 5℃、溶剂与二元酸用量比 30mL∶10g ;提纯过程 :结晶气速 5× 10 -6～ 8× 10 -6m3 /s、降温速率 1/ 3℃ /min、降温终点 2 0℃、结晶保温时间 2 0min、升温速率 1/ 2℃ /min、发汗终温 6 5℃、发汗保留时间 10min。在最佳工艺条件下分离、提纯得到的戊二酸纯度为 99 36 % ,戊二酸的回收率为 70 16 %。     

生态修复植物蜈蚣草中砷的回收

采用管式炉高温热解-NaOH-Na₂CO₃混合液碱浸-CuSO₄·5H₂O沉淀的方法回收生态修复植物蜈蚣草中的砷，最终得到产品砷酸铜。该方法的最佳工艺条件为：热解温度600 ℃，热解时间30 min，CaO加入量（CaO与蜈蚣草的质量比）8%； m（NaOH）∶m（Na₂CO₃）=1∶3，碱浸温度70 ℃， 碱浸时间2 h， 固液比1∶10； 沉淀反应pH 5， 沉淀反应温度70 ℃。采用该方法处理生态修复植物蜈蚣草，得到产品砷酸铜的纯度为93%，砷回收率达88%。     

利用矾泥制备铵明矾

采用酸熔法分离矾泥中的铝与硅，不仅克服了碱浸工艺脱硅的复杂过程和铝回收率低的不足，而且解决了酸浸工艺中产品纯度低和设备材质要求高等问题，通过试验确定了酸熔最佳工艺条件为：温度200℃，时间30min，酸铝比1.18，活性铝的回收率为96.69%，铵明矾的纯度在99.5%以上。     

废聚碳酸酯水解法制双酚A

以1,4-二氧六环为溶剂、NaOH为催化剂,采用废聚碳酸酯(PC)常压水解法制双酚A(BPA).对反应影响因素进行了研究.实验结果表明,在反应温度为100℃、反应时间为8h、m(NaOH):m(水+溶剂)=1:33、m(溶剂):m(PC)=4:1、m(水):m(PC)=1:1的最佳反应条件下,PC水解率大于98%,BPA收率大于95%.     

模拟氯化钠盐渣的高温处理

采用高温处理法对模拟氯化钠盐渣（简称盐渣）进行处理，研究了加热过程中气体有机物产生量随加热时间的变化规律以及加热温度对气体有机物产生量的影响，并分析了盐渣的高温处理效果。实验结果表明：含苯盐渣、含异丁醇盐渣、含氯苯盐渣、含二甲苯盐渣和混合盐渣在高于盐渣中所含有机物沸点30 ℃的条件下加热120 min，盐渣中的有机物去除率均大于99.99%;混合盐渣的加热温度越高，气体有机物的产生速率越快，相同时间内有机物的去除率也越大;盐渣中有机物的气化分离可分为3个阶段，初始阶段有机物气化速率较小，中间阶段气体有机物产生量迅速增加，最后阶段大部分有机物从盐渣中气化分离;盐渣中的有机物在高温气化时，会发生一定的化学反应，有微量的新物质生成。     

废聚苯乙烯泡沫塑料的催化裂解

为了对废聚苯乙烯泡沫塑料（WPS）资源化利用,通过对WPS进行催化裂解的方法,研究了催化剂种类和裂解温度对裂解时间、裂解油产率、苯乙烯回收率以及裂解油纯度的影响。研究结果表明,催化剂种类和裂解温度对裂解反应有着重要影响。裂解温度升高,裂解油产率提高,裂解时间缩短,但苯乙烯选择性下降；低于380 ℃时,氧化钙的裂解油产率和裂解时间优于氧化铝和氯化铝,但苯乙烯的选择性劣于氧化铝和氯化铝；高于400 ℃时,氯化铝、氧化铝和氧化钙的催化活性接近。在实验条件下,WPS催化裂解的最佳催化剂为氯化铝,380 ℃下的裂解时间为25 min,裂解油产率为85.48%,裂解油中苯乙烯含量为80.66%（w）,且副产物较少。     

用含锌废催化剂制备纳米氧化锌

以含锌废催化剂为原料，经酸浸、除杂、锌粉置换、合成等工艺制得碱式碳酸锌，再经过滤、洗涤、干燥、煅烧制备纳米氧化锌。考察了酸浸工艺硫酸溶液含量和液固比（硫酸与含锌废催化剂的质量比）对锌浸出率的影响，以及煅烧温度对纳米氧化锌质量的影响。实验结果表明：在硫酸质量分数为30%、液固比为5的最佳酸浸工艺条件下，锌浸出率为92%；在最佳煅烧温度为400 ℃的条件下，氧化锌质量分数大于95%，比表面积大于50 m²/g；纳米氧化锌颗粒大小均匀，平均粒径小于50 nm。     

从铜氨废液中回收铜

分别采用化学沉淀法和电解法从电镀污泥水热合成铁氧体后过滤分离的铜氨废液中回收铜。实验结果表明：采用化学沉淀法处理铜氨废液，以体积比为1：1的盐酸调节铜氨废液pH为5．4～6．4，沉淀出碱式氯化铜固体，铜回收率在98％以上，1L铜氨废液可回收碱式氯化铜5．83g（合铜3．50g）；采用电解法处理铜氨废液，在电流密度250A／m^2、电解时间5h、电解温度60℃的条件下，1L铜氨废液可回收3．54g铜粉，铜回收率超过99％，铜粉的粒径和纯度均可达到GB5246-85《电解铜粉》的要求。     

Distribution of Cd,Ck, Pb and Zn in Soil and Vegetation Compartments in Stands of Five Boreal Tree Species in N.E. Sweden

Concentrations and total quantity of cadmium (Cd), cupper (Cu),lead (Pb) and zink (Zn) were determined in biomass and soil compartments in a replicated tree species experiment with 27-yr-old stands growing on former farmland in N.E. Sweden. Sequentialextractions of soil samples were performed in order to estimate the exchangeable and an organically bound fraction of each element. The tree species included were Picea abies (L.)H. Karst., Pinus sylvestris L., Pinus contorta Dougl., Larix sibirica Ledeb., and Betula pendula Roth.Tree species influenced the rate of removal of Cu, Pb and Zn incase of stemwood harvesting, and of Cd, Cu and Zn in the case ofwhole-tree harvesting. B. pendula and P. abies had higher quantities and average concentrations of Zn in the biomass. For all species, >50% of the Zn in the stems was found in the bark. P. abies and L. sibirica had higher quantities of Cu in the biomass than the other species.P. abies and P. contorta had high quantities of Cd inthe biomass in relation to the other species. Branches and stembark contained high concentrations of Cd and Pb in relation to foliage and stemwood. Dead branches had especially high concentrations of Pb. The high accumulation rate of Zn in thebiomass of B. pendula was related to a low exchangeable amount of Zn in the A horizon. In the superficial centimeters ofthe A horizon, a depletion similar to that found for Zn was detected for Cu, whereas for Cd and Pb, no correlations were found between quantities of elements in the trees and element pools in the soil.     

Programs assessing implementation and effectiveness of state forest practice rules and BMPs in the West

The major forest nonpoint source control programs in the West are largely regulatory, either under forest practices acts (California, Idaho, New Mexico, Nevada, Oregon, and Washington) or a streamside management act (Montana). These programs and the specific rules they enforce continue to undergo intensive scrutiny. Still, the questions are the same for these regulatory programs as for states that base nonpoint source control on voluntary BMPs (Arizona, Colorado, Utah, Wyoming). Are the rules or BMPs being applied, and are they effective in reducing nonpoint source pollution to levels that protect beneficial uses of water? The level of debate about forestry in the West has resulted in detailed monitoring and research to answer these questions. In the past, state agencies have assumed levels of BMP compliance based on the percent of operations without enforcement actions. These estimates are being replaced by statistically valid and reproducible monitoring of forest practices rules and BMP compliance levels. BMP effectiveness is being assessed using both qualitative and quantitative methods. This can involve field assessments, process-based research, and control watershed studies. Some trend monitoring is also beginning. With the regional implementation rate for forestry BMPs at about 94% and rising, it is likely that effectiveness testing will continue to be a priority and consume the majority of assessment resources for this region.     

Starch-plastic materials—Preparation,physical properties,and biodegradability (a review of recent USDA research)

Recent starch-plastic research at the National Center for Agricultural Utilization Research is reviewed and related worldwide efforts are noted. Properties of starch that influence its formulation and performance in plastics are discussed. Methods are given for preparation of starch-poly(methyl acrylate) graft copolymer, starch-poly(ethylene-co-acrylic acid), and starch-poly(ethylene-co-acrylic acid)-polyethylene plastics. Their physical properties are discussed, as is degradability by enzymes or amylolytic organisms from soil, ponds, and streams.The mention of firm names or trade products does not imply that they are endorsed or recommended by the U.S. Department of Agriculture over other firms or similar products not mentioned.     

四氮唑废水处理工艺设计

高浓度、高盐分的四氮唑生产废水通过三效蒸发浓缩，馏出液经铁炭氧微电解和混凝预处理，再采用水解酸化一接触氧化一反应二沉主体组合工艺进行处理。研究了该工艺所需构筑物和设备的设计与选型。该工艺在正常运行条件下，处理后出水pH6～9，COD 302mg／L，BOD5 108mg／L，SS30mg／L，色度36倍，水质达到GB8978--1996（污水综合排放标准》三级标准。     

Application of Cellulose Microfibrils in Polymer Nanocomposites

Cellulose microfibrils obtained by the acid hydrolysis of cellulose fibers were added at low concentrations (2–10% w/w) to polymer gels and films as reinforcing agents. Significant changes in mechanical properties, especially maximum load and tensile strength, were obtained for fibrils derived from several cellulosic sources, including cotton, softwood, and bacterial cellulose. For extruded starch plastics, the addition of cotton-derived microfibrils at 10.3% (w/w) concentration increased Young’s modulus by 5-fold relative to a control sample with no cellulose reinforcement. Preliminary data suggests that shear alignment significantly improves tensile strength. Addition of microfibrils does not always change mechanical properties in a predictable direction. Whereas tensile strength and modulus were shown to increase during addition of microfibrils to an extruded starch thermoplastic and a cast latex film, these parameters decreased when microfibrils were added to a starch–pectin blend, implying that complex interactions are involved in the application of these reinforcing agents.     

Hysteresis in Reversal of Central European Mountain Lakes from Atmospheric Acidification

Extremely high emissions of S and N compounds in Central Europe (both 280 mmol m^-2 yr^-1) declined by 70and 35%, respectively, during the last decade. Decreaseddeposition rates of SO₄ ^-2, NO₃ ^-, and NH₄ ⁺ in the region paralleled emission declines. The reduction in atmospheric inputs of S and N to mountain ecosystemshas resulted in a pronounced reversal of acidification in the Tatra Mountains and Bohemian Forest lakes. Between the 1987–1990and 1997–1999 periods, concentrations of SO₄ ^-2 and NO₃ ^- decreased (average ± standard deviation) by 22±7 and 12±7 mol L^-1, respectively, in theTatra Mountains, and by 19±7 and 15±10 mol L^-1, respectively, in the Bohemian Forest. Their decrease was compensated in part (1) by a decrease in Ca²⁺ + Mg²⁺ (17±7 mol L^-1) and H⁺ (4±6 mol L^-1), and an increase in HCO₃ ^-(10±10 mol L^-1) in the Tatra Mountains lakes, and (2) by a decrease in Al (7±4 mol L^-1), Ca²⁺ + Mg²⁺ (9±6 mol L^-1), and H⁺ (6±5 mol L^-1), in Bohemian Forest lakes. Despite the rapid decline in lake water concentrations of SO₄ ^-2 and NO₃ ^- in response to reduced S and N emissions, their present concentrations in some lakes are higher than predictionsbased on observed concentrations at comparable emission rates during development of acidification. This hysteresis in chemical reversal from acidification has delayed biological recovery of the lakes. The only unequivocal sign of biological recovery hasbeen observed in erné Lake (Bohemian Forest) where a cladoceran species Ceriodaphnia quadrangular has recentlyreached its pre-acidification abundance.     

Reconstruction of Long-Term Changes in Lake water Chemistry,Zooplankton and Benthos of a Small,Acidified High-Mountain Lake: Magic Modelling and Palaeolimnogical Analysis

Starolesnianske pleso is a small and shallow acid lake in the High Tatra Mountains, situated at 2000 m above sea level, on granitic bedrock, with sparse and thin soil cover. When detailed measurements began in the 1980s Starolesnianske pleso had pH below 5 and only one species of cladoceran zooplankton, the ubiquitous Chydorus sphaericusPalaeolimnological investigations show changes in cladoceran zooplankton and chironomid zoobenthic assemblages since about 1920 and a major change in 1970–1980. The dynamic acidification model MAGIC was used to reconstruct changes in water chemistry over the past 150 years. The results from MAGIC agree well with the sediment record; pH levels gradually decreased from 6.5 in the mid-1800s to about 5.6 in 1920 (first response in biota) to below 5.0 by 1970, and concentrations of inorganic aluminium rose dramatically beginning about 1960. In the 1990s the lake water chemistry showed clear signs of reversal in acidification brought about by a major decline in S deposition.     

Does Soil Acidification Affect Spruce Needle Chemical Composition and Tree Growth?

In 1994, a large survey of soil chemistry was undertaken in thecounty of Värmland in central Sweden (Lundström et al., 1998).The southern part of the county was affected by soilacidification whereas there were no such indications in thenorthern part. To investigate the influence of soil chemistryon the trees at the specific sites, the survey was continued byan analysis of needle chemistry (Norway spruce) which wasundertaken at 150 of the 180 sites, and of tree growth at 65 ofthe 180 sites. Growth was expressed as a ratio between expectedgrowth, estimated with a national, empirical growth model, andthe growth observed in the field. In statistical analyses,using rank correlation, PCA and PLS, there were only weakindications of an influence of soil chemistry on needlechemistry and on tree growth. A moderate correlation betweennitrogen and sulphur in needles was found, which wasinterpreted as an effect of deposition and of processes in thetree canopy. No obvious regional pattern of the growth ratiowas found, in contrast to the clear pattern of soilacidification. The statistical analysis could not with anycertainty point out any of the soil chemistry variables asespecially important for the tree growth ratio.     

Heavy Metals Removal by Biosorption and Flotation

The removal of a mixture of heavy (toxic) metal cations (copper, nickeland zinc) from liquid effluents was investigated in this study at pilotscale, using counter-current contact mode. The innovative processinvolved the abstraction of metal ions onto fungal biosorbents, followedby the application of flotation for the subsequent solid/liquid separationof biomass particles. The ability of microorganisms to remove metal ionsfrom aqueous solutions is a well-known phenomenon. Nevertheless,engineering considerations are very important in decisions, concerningthe commercial future of biosorption and practical solutions are neededfor certain problems, such as the efficient post-separation ofmetal-loaded biomass. The two processes (flotation and biosorption) caneffectively operate in combination, in what it was termed biosorptiveflotation process. The sorbents may be recycled, after appropriate elutionof metals, as well as the treated (clean) water.     

Bioassessment of silvicultural impacts in streams and wetlands of the Eastern United States

Bioassessment is a useful tool to determine the impact of logging practices on the biological integrity of streams and wetlands. Measuring biota directly has an intuitive appeal for impact assessment, and biota can be superior indicators to physical or chemical characteristics because they can reflect cumulative impacts over time. Logging can affect stream and wetland biota by increasing sedimentation rates, altering hydrologic, thermal, and chemical regimes, and changing the base of food webs. Biotic impacts of logging on streams compared to wetlands probably differ, and in this paper we review some of those differences. In streams, invertebrates, fishes, amphibians, algae, and macrophytes have been used as indicators of logging impacts. In wetlands, bioassessment is just beginning to be used, and plants and birds are the most promising indicator taxa. Various best management practices (BMPs) have been developed to reduce the impacts of logging on stream and wetland biota, and we review quantitative studies that have evaluated the efficacy of some of these techniques in streams and wetlands in the eastern United States. Remarkably few studies that address the overall efficacy of BMPs in limiting biotic changes in streams and wetlands after BMP implementation have been published in scientific journals, although some work exists in reports or is unpublished. We review these works, and compile conclusions about BMP efficacy for biota from this body of research.