镀锌钢板废料中锌的碱浸过程影响因素分析

以强碱(NaOH)溶液为浸取剂,采用碱浸法回收镀锌钢板废料中的锌,考察了不同因素(反应温度、反应时间、碱浓度、添加剂)对锌浸出效果的影响,并对添加剂的作用机理进行了分析。实验结果表明:在NaOH质量浓度为250 g/L、反应温度为90℃、反应时间为300 min的最佳工艺条件下,锌的浸出率高达97.89%;添加NaNO_3可提高锌在碱液中的腐蚀电位和腐蚀电流,从而加快镀锌钢板废料中锌的溶解,缩短反应时间;添加KMnO_4对反应速率基本无影响。     

离子液体对废旧印刷线路板中铜、锌、铅的浸出规律

以离子液体1-丁基磺酸-3-甲基咪唑三氟甲烷磺酸盐([BSO_3HMIm]OTf)为浸出剂,初步研究了WPCBs浸铜过程中锌和铅浸出率的影响因素。实验结果表明:铜、锌的浸出率随着WPCBs粒径的减小、H_2O_2溶液加入量的增大而增大,铜的浸出率随浸出温度的升高先增大后减小,锌的浸出率受浸出温度影响不大;铅的浸出率受5种因素影响不大,且总体处于较低水平。在WPCBs粒径为0.100~0.250 mm、离子液体加入量为60.0%(φ)、H_2O_2溶液加入量为7.5%(φ)、固液比为1∶15、浸出温度为50℃的条件下,铜、锌、铅的浸出率分别为99.84%,93.25%,22.46%。     

废弃SCR催化剂中钒和钨的浸出及回收

采用NaOH溶液一次性浸出废弃SCR催化剂中的钒和钨,并用硫酸对浸出液进行除杂,再利用NH4Cl和硫酸分步对浸出液中的钒和钨进行沉淀回收。在NaOH质量分数40%、液固比8、浸出时间4 h、浸出温度90℃的最佳碱浸条件下,钒和钨的浸出率分别达到90.44%和84.49%。除杂过程的铝去除率达到100%,硅去除率达到77.56%。在沉钒pH为8.0、n(NH_4~+)∶n(V)为4的最佳沉钒条件下,钒回收率达到82.79%。在n(SO_4~(2-))∶n(W)为2的最佳沉钨条件下,钨回收率达到76.41%。     

卤素法电镀锡阳极泥中锡的碱浸回收及动力学分析

以NaOH溶液为浸出剂,采用碱浸法回收卤素法电镀锡阳极泥中的锡,考察了浸出效果的影响因素,并对浸出过程的动力学进行了研究。实验结果表明:在NaOH质量浓度200 g/L、反应温度90℃、液固比6、反应时间240 min的最佳工艺条件下,锡的浸出率约为98%;最佳工艺条件下,浸出液中的氟离子对后续锌粉置换回收锡没有影响;在303.15~363.15 K范围内,该浸出过程主要受内扩散控制,反应活化能为9.725 k J/mol。     

从含铬铝泥中回收铝的新工艺

采用"打浆水洗除Cr(Ⅵ)—电渗析除Cr(Ⅵ)—碱浸提铝—碳酸化分解法精制Al_2O_3"的新工艺处理含铬铝泥(以下简称铝泥),并回收Al_2O_3。实验结果表明:铝泥在70℃下经3次打浆水洗后,w(Na_2CrO_4)(以干铝泥计)降至5.0%;采用电渗析除Cr(Ⅵ)工艺可有效去除铝泥中以结合态和结晶态形式存在的Na_2CrO_4,在55 V直流电压下电渗析6h后铝泥中的w(Na_2CrO_4)降至0.98%;在碱浸温度为100℃、碱浸时间为3 h、NaOH质量浓度为150 g/L的优化碱浸条件下,铝浸出率(以Al_2O_3计)高达90.0%;经3次碳酸化分解处理后,Al_2O_3产品的纯度达98.65%,满足GB/T 24487-2009《氧化铝》中的一级标准,Al_2O_3回收率为96.37%。     

膜电解法退镀废ABS电镀件及回收铜和镍

采用膜电解法对废丙烯腈-丁二烯-苯乙烯（ABS）电镀件进行退镀处理。以退镀废液作为阴极液和阳极液，在阳极室退镀ABS电镀件，在阴极室电解退镀废液，进行铜镍分离，回收铜粉和NiCl₂。实验结果表明：在阴极电流密度为500 A/m²、初始铜离子质量浓度为24.00 g/L的条件下电解160 min，阴极铜回收率可达97.65%，电流效率达86.60%，得到的铜粉纯度为97%~99%，处理1 L退镀废液可回收铜粉20.0 g，2 mol/L盐酸0.87 L，NiCl₂晶体43.8 g;在阳极电流密度为500 A/m²、液固比为6的条件下电解60 min， ABS电镀件的退镀率为77.22%。     

用含锌废催化剂制备纳米氧化锌

以含锌废催化剂为原料,经酸浸、除杂、锌粉置换、合成等工艺制得碱式碳酸锌,再经过滤、洗涤、干燥、煅烧制备纳米氧化锌。考察了酸浸工艺硫酸溶液含量和液固比(硫酸与含锌废催化剂的质量比)对锌浸出率的影响,以及煅烧温度对纳米氧化锌质量的影响。实验结果表明:在硫酸质量分数为30%、液固比为5的最佳酸浸工艺条件下,锌浸出率为92%;在最佳煅烧温度为400℃的条件下,氧化锌质量分数大于95%,比表面积大于50 m2/g;纳米氧化锌颗粒大小均匀,平均粒径小于50 nm。     

三维与二维电解工艺处理丙烯腈废水的效果比较

采用三维电解工艺和二维电解工艺处理高浓度丙烯腈废水。实验结果表明:三维电解工艺对COD、TOC、TN和总凯氏氮(TKN)的去除率分别为45.32%、59.55%、61.42%和59.24%,二维电解工艺对COD、TOC、TN和TKN的去除率分别为32.65%、43.53%、46.04%和46.08%;三维电解工艺去除单位COD的能耗为2.72 kW·h/kg,二维电解工艺为1.52 kW·h/kg;三维电解工艺和二维电解工艺的出水BOD_5/COD分别由原水的0.14提高至0.38和0.29。三维电解工艺具有较高的去除率,但能耗也较高。在实际应用中可根据具体情况选择所采用的工艺。     

钛基锡锑电极电催化氧化处理硝基苯废水

采用钛基锡锑(Sn-Sb/Ti)电极作为氧化阳极,不锈钢为阴极,电催化氧化降解废水中硝基苯。实验结果表明,处理硝基苯废水的最佳条件为:电流密度25 mA/cm~2;Na_2SO_4作为电解质,加入量15g/L;极板间距2 cm;溶液初始pH 6。在此最佳条件下,硝基苯去除率大于95%,TOC去除率大于80%,表明Sn-Sb/Ti阳极能有效去除废水中有机污染物。     

活性碳纤维吸附处理对硝基苯酚生产废水

采用活性碳纤维(ACF)吸附处理对硝基苯酚(PNP)生产废水,考察了动态吸附和脱附过程.实验结果表明,在298 K、pH 4时,最佳进水流量为0.25 L/h,ACF的有效吸附量为439.3 mg/g,PNP去除率大于99.95%,TOC去除率大于99.5%,脱附率大于99.5%,ACF的吸附--脱附性能稳定.ACF吸附和电解相结合的工艺能有效去除废水中的有害物质,回收利用PNP和氯化钠,实现了PNP的清洁生产.     

Distribution of Cd,Ck, Pb and Zn in Soil and Vegetation Compartments in Stands of Five Boreal Tree Species in N.E. Sweden

Concentrations and total quantity of cadmium (Cd), cupper (Cu),lead (Pb) and zink (Zn) were determined in biomass and soil compartments in a replicated tree species experiment with 27-yr-old stands growing on former farmland in N.E. Sweden. Sequentialextractions of soil samples were performed in order to estimate the exchangeable and an organically bound fraction of each element. The tree species included were Picea abies (L.)H. Karst., Pinus sylvestris L., Pinus contorta Dougl., Larix sibirica Ledeb., and Betula pendula Roth.Tree species influenced the rate of removal of Cu, Pb and Zn incase of stemwood harvesting, and of Cd, Cu and Zn in the case ofwhole-tree harvesting. B. pendula and P. abies had higher quantities and average concentrations of Zn in the biomass. For all species, >50% of the Zn in the stems was found in the bark. P. abies and L. sibirica had higher quantities of Cu in the biomass than the other species.P. abies and P. contorta had high quantities of Cd inthe biomass in relation to the other species. Branches and stembark contained high concentrations of Cd and Pb in relation to foliage and stemwood. Dead branches had especially high concentrations of Pb. The high accumulation rate of Zn in thebiomass of B. pendula was related to a low exchangeable amount of Zn in the A horizon. In the superficial centimeters ofthe A horizon, a depletion similar to that found for Zn was detected for Cu, whereas for Cd and Pb, no correlations were found between quantities of elements in the trees and element pools in the soil.     

Programs assessing implementation and effectiveness of state forest practice rules and BMPs in the West

The major forest nonpoint source control programs in the West are largely regulatory, either under forest practices acts (California, Idaho, New Mexico, Nevada, Oregon, and Washington) or a streamside management act (Montana). These programs and the specific rules they enforce continue to undergo intensive scrutiny. Still, the questions are the same for these regulatory programs as for states that base nonpoint source control on voluntary BMPs (Arizona, Colorado, Utah, Wyoming). Are the rules or BMPs being applied, and are they effective in reducing nonpoint source pollution to levels that protect beneficial uses of water? The level of debate about forestry in the West has resulted in detailed monitoring and research to answer these questions. In the past, state agencies have assumed levels of BMP compliance based on the percent of operations without enforcement actions. These estimates are being replaced by statistically valid and reproducible monitoring of forest practices rules and BMP compliance levels. BMP effectiveness is being assessed using both qualitative and quantitative methods. This can involve field assessments, process-based research, and control watershed studies. Some trend monitoring is also beginning. With the regional implementation rate for forestry BMPs at about 94% and rising, it is likely that effectiveness testing will continue to be a priority and consume the majority of assessment resources for this region.     

Starch-plastic materials—Preparation,physical properties,and biodegradability (a review of recent USDA research)

Recent starch-plastic research at the National Center for Agricultural Utilization Research is reviewed and related worldwide efforts are noted. Properties of starch that influence its formulation and performance in plastics are discussed. Methods are given for preparation of starch-poly(methyl acrylate) graft copolymer, starch-poly(ethylene-co-acrylic acid), and starch-poly(ethylene-co-acrylic acid)-polyethylene plastics. Their physical properties are discussed, as is degradability by enzymes or amylolytic organisms from soil, ponds, and streams.The mention of firm names or trade products does not imply that they are endorsed or recommended by the U.S. Department of Agriculture over other firms or similar products not mentioned.     

High Immobilization of NH4+ in Danish Heath Soil Related to Succession,Soil and Nutrients: Implications for Critical Loads of N

During recent decades heathlands havechanged into grasslands in regions with high atmosphericnitrogen deposition. In regions with intermediatedeposition level (e.g., Denmark) changes have been lesspronounced which may be due to delay or decrease inresponse of the ecosystem. The mor layer (O horizon) mayplay an important role for this delay due to high sinkstrength for N. In this study, the capacity for netNH₄ ⁺ immobilization and mineralization wasstudied during short- and long-term incubations (2–36 days)of mor samples from Danish dry inland heaths. High short-term capacity for net NH₄ ⁺ immobilization wasfound to be a general characteristic of Danish heath morlayers both under heather (Calluna vulgaris) andcrowberry (Empetrum nigrum ssp nigrum), the latterdominating late stages in heathland succession. The netNH₄ ⁺ immobilization was higher under youngcompared to old or dead vegetation, and higher on lessnutrient poor soils than on extremely nutrient poor soils.The addition of N, P and C stimulated CO₂ productionand net NH₄ ⁺ immobilization, but not net Nmineralization. The immobilization of ¹⁵NH₄ ⁺caused release of dissolved organic N, increased N anddecreased C/N ratio in the microbial biomass, and indicatedgrowth of microorganisms with other metabolic abilitiesthan the indigenous population. No evidence was obtained ofstabilization of immobilized ¹⁵NH₄ ⁺ intosoil organic matter during the experiment. On background ofthe results and current knowledge it was concluded that therecognition of the high capacity for net NH₄ ⁺immobilization in mor layers does not allow for a raiseof critical loads for N for northern dry inland heaths.     

Hysteresis in Reversal of Central European Mountain Lakes from Atmospheric Acidification

Extremely high emissions of S and N compounds in Central Europe (both 280 mmol m^-2 yr^-1) declined by 70and 35%, respectively, during the last decade. Decreaseddeposition rates of SO₄ ^-2, NO₃ ^-, and NH₄ ⁺ in the region paralleled emission declines. The reduction in atmospheric inputs of S and N to mountain ecosystemshas resulted in a pronounced reversal of acidification in the Tatra Mountains and Bohemian Forest lakes. Between the 1987–1990and 1997–1999 periods, concentrations of SO₄ ^-2 and NO₃ ^- decreased (average ± standard deviation) by 22±7 and 12±7 mol L^-1, respectively, in theTatra Mountains, and by 19±7 and 15±10 mol L^-1, respectively, in the Bohemian Forest. Their decrease was compensated in part (1) by a decrease in Ca²⁺ + Mg²⁺ (17±7 mol L^-1) and H⁺ (4±6 mol L^-1), and an increase in HCO₃ ^-(10±10 mol L^-1) in the Tatra Mountains lakes, and (2) by a decrease in Al (7±4 mol L^-1), Ca²⁺ + Mg²⁺ (9±6 mol L^-1), and H⁺ (6±5 mol L^-1), in Bohemian Forest lakes. Despite the rapid decline in lake water concentrations of SO₄ ^-2 and NO₃ ^- in response to reduced S and N emissions, their present concentrations in some lakes are higher than predictionsbased on observed concentrations at comparable emission rates during development of acidification. This hysteresis in chemical reversal from acidification has delayed biological recovery of the lakes. The only unequivocal sign of biological recovery hasbeen observed in erné Lake (Bohemian Forest) where a cladoceran species Ceriodaphnia quadrangular has recentlyreached its pre-acidification abundance.     

Reconstruction of Long-Term Changes in Lake water Chemistry,Zooplankton and Benthos of a Small,Acidified High-Mountain Lake: Magic Modelling and Palaeolimnogical Analysis

Starolesnianske pleso is a small and shallow acid lake in the High Tatra Mountains, situated at 2000 m above sea level, on granitic bedrock, with sparse and thin soil cover. When detailed measurements began in the 1980s Starolesnianske pleso had pH below 5 and only one species of cladoceran zooplankton, the ubiquitous Chydorus sphaericusPalaeolimnological investigations show changes in cladoceran zooplankton and chironomid zoobenthic assemblages since about 1920 and a major change in 1970–1980. The dynamic acidification model MAGIC was used to reconstruct changes in water chemistry over the past 150 years. The results from MAGIC agree well with the sediment record; pH levels gradually decreased from 6.5 in the mid-1800s to about 5.6 in 1920 (first response in biota) to below 5.0 by 1970, and concentrations of inorganic aluminium rose dramatically beginning about 1960. In the 1990s the lake water chemistry showed clear signs of reversal in acidification brought about by a major decline in S deposition.     

Bioassessment of silvicultural impacts in streams and wetlands of the Eastern United States

Bioassessment is a useful tool to determine the impact of logging practices on the biological integrity of streams and wetlands. Measuring biota directly has an intuitive appeal for impact assessment, and biota can be superior indicators to physical or chemical characteristics because they can reflect cumulative impacts over time. Logging can affect stream and wetland biota by increasing sedimentation rates, altering hydrologic, thermal, and chemical regimes, and changing the base of food webs. Biotic impacts of logging on streams compared to wetlands probably differ, and in this paper we review some of those differences. In streams, invertebrates, fishes, amphibians, algae, and macrophytes have been used as indicators of logging impacts. In wetlands, bioassessment is just beginning to be used, and plants and birds are the most promising indicator taxa. Various best management practices (BMPs) have been developed to reduce the impacts of logging on stream and wetland biota, and we review quantitative studies that have evaluated the efficacy of some of these techniques in streams and wetlands in the eastern United States. Remarkably few studies that address the overall efficacy of BMPs in limiting biotic changes in streams and wetlands after BMP implementation have been published in scientific journals, although some work exists in reports or is unpublished. We review these works, and compile conclusions about BMP efficacy for biota from this body of research.     

Characterization of air emissions and residual ash from open burning of electronic wastes during simulated rudimentary recycling operations

Air emissions and residual ash samples were collected and analyzed during experiments of open, uncontrolled combustion of electronic waste (e-waste), simulating practices associated with rudimentary e-waste recycling operations. Circuit boards and insulated wires were handled separately to simulate processes associated with metal recovery. The average emissions of polychlorinated dibenzodioxins and dibenzofurans (PCDD/PCDFs) were 92 ng toxic equivalency (TEQ)/kg [n = 2, relative standard deviation (RSD) = 98%] and 11 900 ng TEQ/kg (n = 3, RSD = 50%) of the initial mass of the circuit boards and insulated wire, respectively. The value for the insulated wire is about 100 times higher than that for backyard barrel burning of domestic waste. The emission concentrations of polybrominated dibenzodioxins and dibenzofurans (PBDD/PBDFs) from the combustion of circuit boards were 100 times higher than for their polychlorinated counterparts. Particulate matter (PM) sampling of the fly ash emissions indicated PM emission factors of approximately 15 and 17 g/kg of the initial mass for the circuit boards and insulated wire, respectively. Fly ash samples from both types of e-waste contained considerable amounts of several metallic elements and halogens; lead concentrations were more than 200 times the United States regulatory limits for municipal waste combustors and 20 times those for secondary lead smelters. Leaching tests of the residual bottom ash showed that lead concentrations exceeded U.S. Environmental Protection Agency landfill limits, designating this ash as a hazardous waste.     

Heavy Metals Removal by Biosorption and Flotation

The removal of a mixture of heavy (toxic) metal cations (copper, nickeland zinc) from liquid effluents was investigated in this study at pilotscale, using counter-current contact mode. The innovative processinvolved the abstraction of metal ions onto fungal biosorbents, followedby the application of flotation for the subsequent solid/liquid separationof biomass particles. The ability of microorganisms to remove metal ionsfrom aqueous solutions is a well-known phenomenon. Nevertheless,engineering considerations are very important in decisions, concerningthe commercial future of biosorption and practical solutions are neededfor certain problems, such as the efficient post-separation ofmetal-loaded biomass. The two processes (flotation and biosorption) caneffectively operate in combination, in what it was termed biosorptiveflotation process. The sorbents may be recycled, after appropriate elutionof metals, as well as the treated (clean) water.     

Urban Metal Flows – A Case Study of Stockholm. Review and Conclusions

Metals have rapidly accumulated in the anthroposphere, especiallyin urban areas, indicating possible environmental and resource problems. Here, Stockholm City was chosen for a case study of urban metal flows, i.e. metal inflow to, metals in the stock of,and metal outflow from the anthroposphere to the biosphere. Themetal stock of Stockholm is large and still growing. The large amounts of metals in the solid waste fraction totally dominatethe outflow from the city. For major parts of the stock, the emissions from goods in use are negligible. There are, however,goods applications corresponding to significant emissions: e.g. the traffic sector (Cu, Zn, Cr, Ni, Pb), the tapwater system (Cu), roofs/fronts or other metal surfaces (Cu, Zn). Today's known metal flows from the anthroposphere of Stockholm to the biosphere and sewage sludge are quantitatively dominated by Zn(34 ton y^-1) and Cu (14 ton y^-1). Historical and present emissions have resulted in high metal concentrations insediments (especially Cd, Hg and Pb, but also Cu and Zn), groundwater (Cu, Hg) and in soils (Hg, Cu, Pb). At present theannual median concentrations are below the Swedish limits for metals in sewage sludge, even if the safety margins aresmall for Cd, Hg and to some extent Cu. The flows of Cu and Zn to Stockholm soils are high with a significant accumulationindicating an environmental impact in a longer time perspective.High levels of metals in surface sediments in the waterenvironments reflects an ongoing input where these metals aretransported from known (Cu, Zn) and or partly unknown (Cd, Hg, Pb) sources. In future urban areas, monitoring of metal flows must be performed both in the anthroposphere and the biospherein order to have a pro active approach to urban environmentalproblems and to get prompt answers to measures taken.