Reactions of the amine-containing drugs fluoxetine and metoprolol during chlorination and dechlorination processes used in wastewater treatment

The reactivities of the amine-containing pharmaceuticals fluoxetine and metoprolol with hypochlorite were studied using conditions that simulate wastewater disinfection including neutral pH (7.0), a range of reaction times (2–60 min), and a molar excess of hypochlorite relative to the pharmaceutical concentration (5.7 times). The reactions were monitored using liquid chromatography (LC) with several detection modes including ultraviolet absorbance (UV), mass spectrometry (MS), and post-column reaction/reductive electrochemistry (EC) for determining active chlorine products. At levels of 10 μM, both compounds reacted rapidly (<2 min) to form principally N-chloramine products that were stable in aqueous solution for at least 1 h. The reaction was also studied in wastewater, and similar reactivity was noted. These results demonstrate that the cations fluoxetine and metoprolol are likely to be rapidly transformed into neutral N-chloramines during wastewater disinfection. The reactivity of the N-chloramines was also studied with sulfite to simulate dechlorination, which is often employed in wastewater treatment. Both N-chloramines reacted slowly with sulfite. In the pure water dechlorination experiments, it was estimated that 70% and 10% of the peak areas remained after 2 min reaction time for fluoxetine and metoprolol, respectively. At longer reaction times both N-chloramines had been completely reduced by sulfite, and the product of the sulfite reduction reaction was the parent pharmaceutical amine. Since typical dechlorination times in wastewater treatment are on the order of seconds, this suggests the chloramines formed from these two basic drugs might evade dechlorination and be released into the environment. The implications of chloramine release are discussed.     

Effects of anions on the kinetics and reactivity of nanoscale Pd/Fe in trichlorobenzene dechlorination

Influences of anionic co-solutes on dechlorination of 1,2,4-trichlorobenzene (124TCB) by the nanoscale Pd/Fe particles were investigated in batch experiments in the presence of an anionic solute such as nitrate, nitrite, perchlorate, phosphate, carbonate, silica, sulfate, sulfite, or sulfide. Based on the extent of inhibitory effects on the 124TCB dechlorination, the anions can be ranked in the order of: control≈sulfate≈silica相似文献   

Making chlorine greener: performance of alternative dechlorination agents in wastewater

The residual chlorine in chlorine-disinfected and dechlorinated wastewater was characterized using a liquid chromatograph that was switched between reversed-phase separation and flow injection analysis modes, permitting measurement of fractionated and total residual chlorine, respectively. Residuals were detected in the effluent of an operating wastewater treatment plant employing chlorine disinfection and sulfite dechlorination. Despite dechlorination, an estimated total residual chlorine of 3 microM (0.2 ppm as Cl2) was detected in the effluent. To improve dechlorination effectiveness, four alternative agents (ascorbic acid, iron, sulfite plus iodide mediator, thiosulfate) were compared to sulfite on laboratory-chlorinated wastewater. Listed in order of decreasing relative effectiveness, we found: iron metal > sulfite plus iodide approximately = thiosulfate > sulfite > ascorbic acid. Only the iron metal column was completely effective at rapidly removing all traces of residual chlorine.     

Unusual products of the aqueous chlorination of atenolol

The reaction of the drug atenolol with hypochlorite under conditions that simulate wastewater disinfection was investigated. The pharmaceutical reacted in 1h yielding three products that were separated by chromatographic techniques and characterized by spectroscopic features. Two unusual products 2-(4-(3-(chloro(2-chloropropan-2-yl)amino)-2-hydroxypropoxy)phenyl) acetamide and 2-(4-(3-formamido-2-hydroxypropoxy)phenyl) acetamide were obtained along with 2-(4-hydroxyphenyl) acetamide. When the reaction was stopped at shorter times only 2-(4-(3-amino-2-hydroxypropoxy)phenyl) acetamide and the dichlorinated product were detected. Tests performed on the seeds of Lactuca sativa show that chlorinated products have phytotoxic activity.     

Effects of dissolved oxygen and iron aging on the reduction of trichloronitromethane, trichloracetonitrile, and trichloropropanone

Iron metal (Fe(0)) is a potent reductant capable of reducing a wide variety of halogenated organic compounds including disinfection byproducts (DBPs). These reduction reactions may play a role in DBP fate in iron water mains and potentially could be exploited to remove DBPs from drinking water or wastewater in a packed-bed configuration. Oxidants (i.e., dissolved oxygen (DO) and chlorine) present in the water, however, may decrease the DBP degradation rate by competing for reactive sites and rapidly aging or corroding the iron surface. Thus, batch experiments were performed to investigate the effect of DO on the degradation rates of selected DBPs by Fe(0). Experiments were performed under anaerobic conditions, in initially oxygen saturated buffer without DO control, and under controlled DO (approximately 4.0 or 8.0 mg l⁻¹) conditions. The effect of short-term (25–105 min) iron aging in DO-containing buffer on DBP degradation rate also was investigated in separate experiments. For fresh Fe(0), the degradation rates of trichloronitromethane (TCNM) and trichloroacetonitrile (TCAN) in initially oxygen saturated buffer were similar to their respective rates under anaerobic conditions. The degradation rate of 1,1,1-trichloropropanone (1,1,1-TCP), however, decreased significantly in the presence of DO and the effect was proportional to DO concentration in the controlled DO experiments. For a DO concentration of 4 mg l⁻¹, the degradation rate of the three DBPs was greater for longer aging times as compared to their respective rates after 25 min, suggesting the formation of a mineral phase that increased reactivity. For a DO concentration of 8 mg l⁻¹, the effects of increasing aging time were mixed. TCNM degradation rates were stable for all aging times and comparable to that under anaerobic conditions. The TCAN and 1,1,1-TCP degradation rates, however, tended to decrease with increasing aging time. These results suggest that the reduction of highly reactive DBPs by Fe(0) will not be affected by the presence of DO but that the reaction rates will be slowed by DO for DBPs with slower degradation kinetics.     

Structure relationship for catalytic dechlorination rate of dichlorobenzenes in water

Three isomers of dichlorobenzene (o-, m- and p-DCB) were dechlorinated by Pd/Fe catalyst in aqueous solutions through catalytic reduction. The dechlorination reaction took place on the surface site of the catalyst via a pseudo-first-order kinetics, and resulted in benzene as the final reduction product. The rate constants of the reductive dechlorination for the three dichlorobenzenes (DCBs) in the presence of Pd/Fe as a catalyst were measured experimentally. In all cases, the reaction rate constants were found to increase with the decrease in the Gibbs free energy of the formation of DCBs. The reaction rate constant for o-, m- and p-DCBs in the presence of 0.020% (w/w) Pd/Fe at 25 °C was determined to be 0.0213, 0.0223, and 0.0254 min⁻¹, respectively. While the activation energy of each dechlorination reaction was measured to be 102.5, 96.6 and 80.0 kJ mol⁻¹ for o-, m- and p-DCBs, respectively. The results demonstrated that p-DCBs were reduced more easily than o- or m-DCBs, and the order of the tendency of the dechlorination was p-DCB > m-DCB > o-DCB. The presented data show the catalytic reduction using Pd/Fe as a catalyst is a fast and easy approach for the dechlorination of DCBs.     

Effects of wastewater disinfection on waterborne bacteria and viruses.

Wastewater disinfection is practiced with the goal of reducing risks of human exposure to pathogenic microorganisms. In most circumstances, the efficacy of a wastewater disinfection process is regulated and monitored based on measurements of the responses of indicator bacteria. However, inactivation of indicator bacteria does not guarantee an acceptable degree of inactivation among other waterborne microorganisms (e.g., microbial pathogens). Undisinfected effluent samples from several municipal wastewater treatment facilities were collected for analysis. Facilities were selected to provide a broad spectrum of effluent quality, particularly as related to nitrogenous compounds. Samples were subjected to bench-scale chlorination and dechlorination and UV irradiation under conditions that allowed compliance with relevant discharge regulations and such that disinfectant exposures could be accurately quantified. Disinfected samples were subjected to a battery of assays to assess the immediate and long-term effects of wastewater disinfection on waterborne bacteria and viruses. In general, (viable) bacterial populations showed an immediate decline as a result of disinfectant exposure; however, incubation of disinfected samples under conditions that were designed to mimic the conditions in a receiving stream resulted in substantial recovery of the total bacterial community. The bacterial groups that are commonly used as indicators do not provide an accurate representation of the response of the bacterial community to disinfectant exposure and subsequent recovery in the environment. UV irradiation and chlorination/dechlorination both accomplished measurable inactivation of indigenous phage; however, the extent of inactivation was fairly modest under the conditions of disinfection used in this study. UV irradiation was consistently more effective as a virucide than chlorination/dechlorination under the conditions of application, based on measurements of virus (phage) diversity and concentration. Taken together, and when considered in conjunction with previously published research, the results of these experiments illustrate several important limitations of common disinfection processes as applied in the treatment of municipal wastewaters. In general, it is not clear that conventional disinfection processes, as commonly implemented, are effective for control of the risks of disease transmission, particularly those associated with viral pathogens. Microbial quality in receiving streams may not be substantially improved by the application of these disinfection processes; under some circumstances, an argument can be made that disinfection may actually yield a decrease in effluent and receiving water quality. Decisions regarding the need for effluent disinfection must account for site-specific characteristics, but it is not clear that disinfection of municipal wastewater effluents is necessary or beneficial for all facilities. When direct human contact or ingestion of municipal wastewater effluents is likely, disinfection may be necessary. Under these circumstances, UV irradiation appears to be superior to chlorination in terms of microbial quality and chemistry and toxicology. This advantage is particularly evident in effluents that contain appreciable quantities of ammonia-nitrogen or organic nitrogen.     

Characterisation of the abiotic degradation pathways of oxytetracyclines in soil interstitial water using LC-MS-MS

The fate of oxytetracyclines (OTCs) in soil interstitial water was investigated and the structure of a number of degradation products elucidated in a time-related experiment. A previously developed separation method for LC–MS–MS able to base separate and quantify OTC and three of its epimers and degradation products was applied. Compounds detected were 4-epi-oxytetracycline (EOTC) (t_R=3.0 min), OTC (t_R=4.4 min), -apo-oxytetracycline (-apo-OTC) (t_R=11.4 min) and β-apo-oxytetracycline (β-apo-OTC) (t_R=18.4 min). Furthermore, we tentatively identified 4-epi-N-desmethyl-oxytetracycline (E-N-DM-OTC) (t_R=3.0 min), N-desmethyl-oxytetracycline (N-DM-OTC) (t_R=3.5), N-didesmethyl-oxytetracycline (N-DDM-OTC), 4-epi-N-didesmethyl-oxytetracycline (E-N-DDM-OTC) (t_R=3.7 and 4.7 min) and 2-acetyl-2-decarboxamido-oxytetracycline (t_R=8.7) in all samples. Most compounds were only present in trace concentrations (less than 2%) relative to the parent OTC. EOTC was on the other hand formed up to a ratio of 0.6 relative to parent OTC concentration. Only EOTC, E-N-DM-OTC, N-DM-OTC, N-DDM-OTC and E-N-DDM-OTC were formed during the time-related experiment. All other compounds were probably only present as impurities in the spiked OTC formulation as they declined in concentration from the start of the experiment. Half-lives (T_1/2, days) of the OTCs in soil interstitial water were in the order of 2 days (EOTC) to 270 days (β-apo-OTC).     

Dechlorination of chlorinated hydrocarbons by bimetallic Ni/Fe immobilized on polyethylene glycol-grafted microfiltration membranes under anoxic conditions

In this study, the dechlorination of chlorinated hydrocarbons including trichloroethylene (TCE), tetrachloroethylene (PCE) and carbon tetrachloride (CT) by bimetallic Ni/Fe nanoparticles immobilized on four different membranes was investigated under anoxic conditions. Effects of several parameters including the nature of membrane, initial concentration, pH value, and reaction temperature on the dechlorination efficiency were examined. The scanning electron microscopic images showed that the Ni/Fe nanoparticles were successfully immobilized inside the four membranes using polyethylene glycol as the cross-linker. The agglomeration of Ni/Fe were observed in poly(vinylidene fluoride), Millex GS and mixed cellulose ester membranes, while a relatively uniform distribution of Ni/Fe was found in nylon-66 membrane because of its hydrophilic nature. The immobilized Ni/Fe nanoparticles exhibited good reactivity towards the dechlorination of chlorinated hydrocarbons, and the pseudo-first-order rate constant for TCE dechlorination by Ni/Fe in nylon-66 were 3.7-11.7 times higher than those in other membranes. In addition, the dechlorination efficiency of chlorinated hydrocarbons followed the order TCE > PCE > CT. Ethane was the only end product for TCE and PCE dechlorination, while dichloromethane and methane were found to be the major products for CT dechlorination, clearly indicating the involvement of reactive hydrogen species in dechlorination. In addition, the initial rate constant for TCE dechlorination increased upon increasing initial TCE concentrations and the activation energy for TCE dechlorination by immobilized Ni/Fe was 34.9 kJ mol⁻¹, showing that the dechlorination of TCE by membrane-supported Ni/Fe nanoparticles is a surface-mediated reaction.     

On the performance of Fe and Fe,F doped Ti-Pt/PbO2 electrodes in the electrooxidation of the Blue Reactive 19 dye in simulated textile wastewater

The electrochemical performance of pure Ti–Pt/β-PbO₂ electrodes, or doped with Fe and F (together or separately), in the oxidation of simulated wastewaters containing the Blue Reactive 19 dye (BR-19), using a filter-press reactor, was investigated and then compared with that of a boron-doped diamond electrode supported on a niobium substrate (Nb/BDD). The electrooxidation of the dye simulated wastewater (volume of 0.1 l, with a BR-19 initial concentration of 25 mg l⁻¹) was carried out under the following conditions: current density of 50 mA cm⁻², volume flow rate of 2.4 l h⁻¹, temperature of 25 °C and electrode area of 5 cm². The performances of the electrodes in the dye decolorization were quite similar, achieving 100% decolorization, and in some cases 90% decolorization was achieved by applying only ca. 0.3 A h l⁻¹ (8 min of electrolysis). The reduction of the simulated wastewater organic load, monitored by its total organic carbon content (TOC), was greater for the Ti–Pt/β-PbO₂–Fe,F electrode obtained from an electrodeposition bath containing 1 mM Fe³⁺ and 30 mM F⁻. In this case, after 2 h of electrolysis the obtained TOC reduction was 95%, while for the pure β-PbO₂ and the Nb/BDD electrodes the reductions were 84% and 82%, respectively.     

Removal of genotoxicity in chlorinated secondary effluent of a domestic wastewater treatment plant during dechlorination

Purpose  

Dechlorination with tetravalent sulfur is widely used in wastewater treatment processes after chlorination. Dechlorination can remove certain genotoxic disinfection by-products (DBPs). However, the reactions occurring during dechlorination of chlorinated secondary effluent and their genotoxic chemicals are still very complex, and the related genotoxicity changes remain unknown. Therefore, the effects of dechlorination on genotoxicity in secondary effluent and its fractions and typical genotoxic chemical after chlorination were evaluated.     

Stimulation of reductive dechlorination of hexachlorobenzene in soil by inducing the native microbial activity

The reductive dechlorination and behaviour of ¹⁴C-hexachlorobenzene (HCB) was investigated in an arable soil. The activity of the native anaerobic microbial communities could be induced by saturating the soil with water. Under these conditions high rates of dechlorination were observed. After 20 weeks of incubation only 1% of the applied ¹⁴C-HCB could be detected in the fraction of extractable residues. Additional organic substances, like wheat straw and lucerne straw, however considerably delayed and reduced the dechlorination process in the soil. The decline of HCB was not only caused by dechlorination but also by the formation of non-extractable residues, whereby their amounts varied with time depending on the experimental conditions. Several dechlorination products were detected, indicating the following main HCB transformation pathway: HCB → PCB → 1,2,3,5-TeCB → 1,3,5-TCB → 1,3-DCB, with 1,3,5-TCB as main intermediate dechlorination product. The other TeCB-, TCB- and DCB-isomers were also detected in low amounts, showing the presence of more than one dechlorination pathway. Since the methane production rates were lowest when the dechlorination rates were highest, it can be assumed that methanogenic bacteria were not involved in the dechlorination process of HCB. The established ¹⁴C-mass balances show, that with increasing dechlorination and incubation times, the ¹⁴C-recoveries decreased.     

Photodegradation of malachite green under natural sunlight irradiation: kinetic and toxicity of the transformation products

This article describes the photolytic degradation of malachite green (MG), a cationic triphenylmethane dye used worldwide as a fungicide and antiseptic in the aquaculture industry. Photolysis experiments were performed by direct exposure of a solution of MG in water to natural sunlight. The main transformation products (TPs) generated during the process were identified by liquid chromatography time-of-flight mass spectrometry (LC–TOF-MS) and gas chromatography mass spectrometry (GC–MS). The 28 TPs identified with this strategy indicate that MG undergoes three main reactions, N-demethylation, hydroxylation and cleavage of the conjugated structure forming benzophenone derivatives. These processes involve hydroxyl radical attack on the phenyl ring, the N,N-dimethylamine group and the central carbon atom. The Vibrio fischeri acute toxicity test showed that the solution remains toxic after MG has completely disappeared. This toxicity could be assigned, at least in part, to the formation of 4-(dimethylamine)benzophenone, which has an EC_50,30 min of 0.061 mg l⁻¹, and is considered “very toxic to aquatic organisms” by current EU legislation.     

Identification and behavior of reaction products formed by chlorination of ethynylestradiol

Six products were formed by reaction of ethynylestradiol (EE2) with sodium hypochlorite in buffered solutions. 4-Chloroethynylestradiol (4-ClEE2) and 2,4-dichloroethynylestradiol (2,4-diClEE2) were identified as the two major reaction products, using preparative HPLC, MS, and NMR. When EE2 reacted with chlorine at different pHs (pH 5, 7, and 9) or chlorine concentrations (0.2, 1, 2, and 5 mmol/l, corresponding to molar ratios to EE2, 1, 5, 10, and 25, respectively), the formation of 4-ClEE2 and 2,4-diClEE2 was observed under the above conditions, and the highest yields were 20 and 52 mol%, respectively. EE2 was consumed almost completely within 5 min of chlorination by addition of chlorine of more than 1 mmol/l (molar ratio to EE2, 5). On the other hand, the two products existed in highly chlorinated solutions after 60 min (4ClEE2, 1-6 mol%; 2,4-diClEE2, 3-25 mol%). The estrogenic activities of 4-ClEE2 by estrogen receptor alpha or beta binding assay were similar to those of the parent EE2, and the activities of 2,4-diClEE2 were lower about 10 times.     

臭氧氧化6-APA制药厂生化处理出水的特性及动力学简

通过现场实验研究了6-APA制药厂生化处理出水的臭氧氧化特性及其动力学规律。结果表明，当臭氧浓度为27.5 mg/L，气水接触时间为80 min时，COD、UV₂₅₄、NH₃-N和色度的去除率分别可达72.95%、73.28%、72%和96.25%，达到《发酵类制药废水工业水污染物排放标准》（GB 21903-2008）排放控制要求。拟合结果表明，在0~10、10~30和30~90 min时段内，臭氧氧化过程遵循拟一级反应，但反应速率逐渐降低。当气水接触时间为30 min时，废水可生化性可由0.1提高至0.35，采用臭氧/生物处理的联合工艺也有望使出水达到相同的排放控制要求。     

Wastewater reuse: modeling chloroform formation

The chloroform is a substance that presents a significant risk to or via the aquatic environment. Thus, the emissions, discharges and losses of this substance need to be controlled during wastewater disinfection for reclamation and reuse purposes. Due to its carcinogenetic potential, multiple studies have been carried out on drinking and surface/natural waters but less consideration has been directed to the wastewater disinfection. The focus of this work studied the formation of chloroform during chlorination in prepared waters or artificial matrices that intended to simulate wastewaters stored in landscape ponds for green areas irrigation. The relation between reaction time, chlorine dose, and chloroform formation and the variation of the dissolved organic carbon (DOC) content during the reaction was assessed. A two-variant model was proposed to simulate breakpoint chlorination practices (when chlorine dose is equal or lower than chlorine demand) and super chlorination techniques (when chlorine dose tends to surpass chlorine demand). The model was validated by the application of actual data from working conditions of six wastewater treatment plants located in Algarve, Portugal, including other data obtained in previous research studies that were not used in the model development, and by comparing the predicted values with real measured ones.     

Reaction of silver nanoparticles in the disinfection process

This study investigated the dissolution, aggregation, and reaction kinetics of silver nanoparticles (AgNPs) with the three types of water disinfectants (ultraviolet, sodium hypochlorite, and ozone) under the different conditions of pH, ionic strength, or humic acid (HA). The physicochemical changes of AgNPs were measured by using UV–Vis spectroscopy, transmission electron microscopy, and inductively coupled plasma optical emission spectrometer. The results showed that when AgNPs contacted the disinfectants, oxidative dissolution was the primary reaction. In addition, the reaction kinetics studies revealed that the reaction rate of AgNPs with disinfectants was significantly influenced by different disinfectants along with different pH and the presence of sodium nitrate and HA. Our research demonstrated the potential effect of disinfectants on AgNPs, which will improve our understanding of the fate of AgNPs in the disinfection processes in the water and wastewater treatment plant.     

Hydrogenolysis of chlorobenzene,dichlorobenzenes and chlorotoluenes by in situ generated and gaseous hydrogen in alkaline media and the presence of Pd/C catalyst

A method for dechlorination of chloroaromatic compounds at room temperature and atmospheric pressure by an in situ generated––in reaction of Al particles with water––or gaseous hydrogen in alkaline media and the presence of Pd/C catalyst was thoroughly investigated, having in mind its possible application in utilization of organochlorine waste. Conversion degree to dechlorinated compounds depended on the constitution of substrates and ranged between 88% and 96% when in situ hydrogen was used (at substrate (chlorine) to catalyst molar ratio 550:1 and over twofold stoichiometric excess of Al relative to substrate (chlorine); the process lasted ca. 26 h until all Al was consumed), or 90–97% if gaseous hydrogen was purged. Effectiveness of dechlorination was markedly affected by stirring, i.e. size of the stirrer and speed of revolution. Prospects for application of the method described were briefly outlined.     

The study on the dechlorination of OCDD with Pd/C catalyst in ethanol-water solution under mild conditions

Dechlorination of octachlorodibenzo-p-dioxin (OCDD) was carried out in ethanol-water (v/v=1:1) solution of NaOH in the presence of Pd/C catalysts with the use of H(2). The substrate was dechlorinated with Pd/C under mild conditions (atmospheric pressure and <100 degrees C) to give a chlorine-free product, dibenzo-p-dioxin (DD), in high yields. After reaction of 3h at 50 degrees C, 95.9% OCDD was degraded to low dechlorinated congeners and the yield of DD was 77.4%. We have also studied the dechlorination selectivity of chlorine atoms on the different substituted positions and postulated the dechlorination pathway of OCDD. For OCDD, the 2-position has higher reactivity than 1-position, but the difference is very small. From the distribution statistics of the intermediates during the reaction, we postulate that the steric effect plays an important role during the reaction and affect the dechlorination pathway of OCDD.     

Fate of cancerostatic platinum compounds in biological wastewater treatment of hospital effluents

The present work focuses on the fate of two cancerostatic platinum compounds (CPC), cisplatin and carboplatin, as well as of two inorganic platinum compounds, [PtCl₄]²⁻ and [PtCl₆]²⁻ in biological wastewater treatment. Laboratory experiments modelling adsorption of these compounds onto activated sludge showed promising specific adsorption coefficients K_D and K_OC and Freundlich adsorption isotherms. However, the adsorption properties of the investigated substances were differing significantly. Adsorption decreased following the order cisplatin > [PtCl₆]²⁻ > [PtCl₄]²⁻ > carboplatin. Log K_D-values were ranging from 2.5 to 4.3 , log K_OC from 3.0 to 4.7.

A pilot membrane bioreactor system (MBR) was installed in a hospital in Vienna and fed with wastewater from the oncologic in-patient treatment ward to investigate CPC-adsorption in a sewage treatment plant. During three monitoring periods Pt-concentrations were measured in the influent (3–250 μg l⁻¹ Pt) and the effluent (2–150 μg l⁻¹ Pt) of the treatment plant using ICP-MS. The monitoring periods (duration 30 d) revealed elimination efficiencies between 51% and 63% based on averaged weekly input–output budgets. The derived log K_D-values and log K_OC-values ranged from 2.4 to 4.8 and from 2.8 to 5.3, respectively. Species analysis using HPLC-ICP-MS proofed that mainly carboplatin was present as intact drug in the influent and – due to low log K_D – in the effluent of the MBR.