Metal release rate from AISI 316L stainless steel and pure Fe, Cr and Ni into a synthetic biological medium--a comparison

Metal release rates from stainless steel grade 316L were investigated in artificial lysosomal fluid (ALF), simulating a human inflammatory cell response. The main focus was placed on release rates of main alloying elements using graphite furnace atomic absorption spectroscopy, and changes in surface oxide composition by means of X-ray photoelectron spectroscopy. To emphasise that alloys and pure metals possess totally different intrinsic properties, comparative studies were performed on the pure alloying constituents: iron, nickel and chromium. Significant differences in release rates were observed due to the presence of a passive surface film on stainless steel. Iron and nickel were released at rates more than 300 times lower from the 316L alloy compared with the pure metals whereas the release rate of chromium was similar. Iron was preferentially released compared with nickel and chromium. Immersion in ALF resulted in the gradual enrichment of chromium in the surface film, a small increase of nickel, and the reduction of oxidized iron with decreasing release rates of alloy constituents as a result. As expected, released metals from stainless steel grade 316L were neither in proportion to the bulk alloy composition nor to the surface film composition.     

Corrosion-induced release of Cu and Zn into rainwater from brass, bronze and their pure metals. A 2-year field study

A 2-year field study has been conducted in an urban environment to provide annual release rates of copper and zinc from brass (20 wt% Zn) and copper and tin from bronze (6 wt% Sn) compared to sheets of their pure alloy constituents, copper and zinc. Despite relatively low nominal bulk alloy content, substantially more zinc was released from brass compared to copper. Both metals were released at a significantly slower rate from the brass alloy, compared to the pure metals. The proportion of release rates of copper and zinc from the alloy differed significantly from their proportions in the bulk alloy. Bronze showed relatively constant release rates of copper, being similar to that of pure copper sheet. The release of tin from bronze was negligible. The results clearly show that alloys and the pure metals behave very differently when exposed to rainwater. Accordingly, release rates from pure metals cannot be used to predict release rates of individual constituents from their alloys. Generated data are of importance within REACH, the new chemical policy of the European commission, where metal alloys erroneously are being treated as mixtures of chemical substances.     

Trace element content in marine algae species from the Black Sea, Turkey

Trace element content of marine algae species collected from the Black Sea coasts were determined by atomic absorption spectroscopy after microwave digestion. Trace element content in marine algae species were 1.70-17.1 microg/g for copper, 3.64-64.8 microg/g for zinc, 9.98-285 microg/g for manganese, 99-3,949 microg/g for iron, 0.50-11.6 microg/g for chromium, 0.27-36.2 microg/g for nickel, 11-694 microg/kg for selenium, 0.50-44.6 microg/kg for cadmium, 1.54-3,969 microg/kg for lead, 1.56-81.9 microg/kg for cobalt. While iron was the highest trace element concentration, cadmium was the lowest in samples. Most of the analyzed samples were edible. The samples are consumed for human diet in several countries.     

Increased metal concentrations in exhaled breath condensate of industrial welders

It was the aim of this study to evaluate the effect of different devices on the metal concentration in exhaled breath condensate (EBC) and to prove whether working conditions in different welding companies result in diverse composition of metallic elements. The influence of two collection devices (ECoScreen, ECoScreen2) on detection of metallic elements in EBC was evaluated in 24 control subjects. Properties of ECoScreen and a frequent use can alter EBC metal content due to contamination from metallic components. ECoScreen2 turned out to be favourable for metal assessment. Concentrations of iron, nickel and chromium in EBC sampled with ECoScreen2 were compared between non-exposed controls and industrial welders. Metal concentrations in EBC were higher in 36 welders recruited from three companies. Exposure to welding fumes could be demonstrated predominantly for increased iron concentrations. Concentrations of iron and nickel differed by working conditions, but chromium could not be detected in EBC.     

Metal Accumulation by Riverine and Lacustrine Populations of Angulyagra Oxytropis (Benson) (Gastropoda : Viviparidae)

Cadmium, chromium, iron, manganese, nickel, lead and zinc concentrations were determined in sediment and body tissues, viz. digestive gland, mantle and shell, of the freshwater snail, Angulyagra oxytropis (Benson) (Gastropoda : Viviparidae), from River Barak and one of its floodplain lakes in Cachar district, Assam State, Northeastern India. The concentrations of all the metals except iron are significantly higher in the lake sediment. When compared to their riverine counterparts, the lacustrine snails contain higher concentrations of cadmium, chromium and iron in their mantle; nickel and zinc in digestive gland; manganese in both digestive gland and mantle; and lead in all the three tissues examined. The accumulation patterns of most of the metals varied considerably between the two sites. The implications of these findings in storage, sequestration and detoxification of metals by this animal are discussed. The study also indicates that A. oxytropis may be a potential biological indicator of metal contamination in freshwater ecosystems.     

Metal concentrations in eight fish species from Aegean and Mediterranean Seas

The concentrations of cadmium, cobalt, chromium, copper, iron, manganese, nickel, lead, and zinc were determined by ICP-AES in muscles and livers of eight fish species sampled from the Aegean and Mediterranean seas of Turkey. Iron showed the highest levels, followed by Zinc in examined tissues of all fish species. Metal concentrations in edible parts of fish species were 0.03–0.37 mg kg^???1 for cadmium, 0.02–0.42 mg kg^???1 for cobalt, 0.15–1.78 mg kg^???1 for chromium, 0.17–1.11 mg kg^???1 for copper, 11.0–33.4 mg kg^???1 for iron, 0.02–0.89 mg kg^???1 for manganese, 0.22–4.03 mg kg^???1 for nickel, 0.22–0.64 mg kg^???1 for lead, and 2.88–10.9 mg kg^???1 for zinc, respectively. All metal concentrations in livers were higher than those in muscles. In some stations, cadmium, chromium, cobalt, and lead concentrations in both muscles and livers of the examined species were higher than permissible safety levels for human uses.     

Evaluation of metal contents of household detergent samples from Turkey by flame atomic absorption spectrometry

The concentrations of cadmium, copper, chromium, cobalt, iron, lead, manganese, nickel, and zinc in detergent samples from Kayseri, Turkey were determined by flame atomic absorption spectrometry. HClO₄ (10 mL)/HNO₃ (10 mL) mixture was used for the digestion of household detergent samples. The correctness of the analytical procedures was checked with standard addition–recovery tests in different detergent samples for the investigated metal ions. The concentration ranges of the elements in the detergent samples were found as 17.2–60.1, 11.1–40.1, 2.5–32.3, 8.1–10.5, 7.2–21.6, 9.8–17.9, 1.7–3.8, 12.5–22.5, and 2.0–5.8 μg/g for iron, manganese, zinc, copper, lead, cobalt, cadmium, nickel, and chromium, respectively. The values found in this work were compared with some other studies around the world conducted on detergent samples.     

Comparison of arsenic, cadmium, chromium, lead, manganese, mercury and selenium in feathers in bald eagle (Haliaeetus leucocephalus), and comparison with common eider (Somateria mollissima), glaucous-winged gull (Larus glaucescens), pigeon guillemot (Cepphus columba), and tufted puffin (Fratercula cirrhata) from the Aleutian Chain of Alaska

There is an abundance of field data for levels of metals from a range of places, but relatively few from the North Pacific Ocean and Bering Sea. In this paper we examine the levels of arsenic, cadmium, chromium, lead, manganese, mercury and selenium in feathers from common eiders (Somateria mollissima), glaucous-winged gulls (Larus glaucescens), pigeon guillemots (Cepphus columba), tufted puffins (Fratercula cirrhata) and bald eagles (Haliaeetus leucocephalus) from the Aleutian Chain of Alaska. Our primary objective was to test the hypothesis that there are no trophic levels relationships for arsenic, cadmium, chromium, lead, manganese, mercury and selenium among these five species of birds breeding in the marine environment of the Aleutians. There were significant interspecific differences in all metal levels. As predicted bald eagles had the highest levels of arsenic, chromium, lead, and manganese, but puffins had the highest levels of selenium, and pigeon guillemot had higher levels of mercury than eagles (although the differences were not significant). Common eiders, at the lowest trophic level had the lowest levels of some metals (chromium, mercury and selenium). However, eiders had higher levels than all other species (except eagles) for arsenic, cadmium, lead, and manganese. Levels of lead were higher in breast than in wing feathers of bald eagles. Except for lead, there were no significant differences in metal levels in feathers of bald eagles nesting on Adak and Amchitka Island; lead was higher on Adak than Amchitka. Eagle chicks tended to have lower levels of manganese than older eagles.     

Trace metal levels and some chemical parameters in herby cheese collected from south eastern Anatolia-Turkey

Due to the consumption of the herby cheese in south eastern Anatolia-Turkey is at high ratio, chemical parameters such as dry matter, pH, acidity, aCl, protein, fat and trace metal contents in 50 different herby cheeses produced at this region have been determined in the presented study. The content of lead, copper, cobalt, nickel, chromium, cadmium, and iron have been analyzed by flame atomic absorption spectrometer in air/acetylene flame after combination ash digestion method and wet digestion method. The mean concentration of lead, copper, cobalt, nickel, chromium and cadmium in our samples are higher than literature values except iron.     

Interspecific and Locational Differences in Heavy Metal Levels in Four Species of Birds Near Sydney, Australia

We examined the levels of cadmium, chromium, lead, manganese, mercury, and selenium in four species of birds near Sydney, New South Wales, Australia in January, 1996. Molted contour feathers were collected from silver gull, Larus novaehollandiae (Royal National Park and downtown Sydney), sulphur-crested cockatoo, Cacatua sulphurea (Blue Mountains, Royal National Park, and Sydney), Australian white ibis, Threskiornis molucca (Sydney), and rock dove Columba livia (Royal National Park and Sydney). We tested the null hypothesis that there were no species or locational differences in metal levels. There were significant species differences in all metals, with rock doves having the highest levels of cadmium, chromium, lead, and manganese, and silver gulls having the highest levels of mercury and selenium. Metal levels were generally low in cockatoos, and were lowest in those from the Royal National Park. For silver gulls, cadmium, lead, and chromium levels were highest at Sydney, and there were no locational differences in manganese, mercury, and selenium levels. For rock doves, cadmium, chromium and manganese were higher in Sydney, and there were no locational differences in lead, mercury, and selenium. Overall, cadmium and chromium levels were significantly higher in Sydney than in the Royal National Park for all species, and there were no locational differences in mercury levels. Although the levels of most metals in feathers from these Australian birds were within the ranges reported worldwide, lead levels in ibises and rock doves were among the highest reported worldwide, suggesting a cause for concern.     

Variability in concentrations of potentially toxic elements in urban parks from six European cities

Use of a harmonised sampling regime has allowed comparison of concentrations of copper, chromium, nickel, lead and zinc in six urban parks located in different European cities differing markedly in their climate and industrial history. Wide concentrations ranges were found for copper, lead and zinc at most sites, but for chromium and nickel a wide range was only seen in the Italian park, where levels were also considerably greater than in other soils. As might be expected, the soils from older cities with a legacy of heavy manufacturing industry (Glasgow, Torino) were richest in potentially toxic elements (PTEs); soils from Ljubljana, Sevilla and Uppsala had intermediate metal contents, and soils from the most recently established park, in the least industrialised city (Aveiro), displayed lowest concentrations. When principal component analysis was applied to the data, associations were revealed between pH and organic carbon content; and between all five PTEs. When pH and organic carbon content were excluded from the PCA, a distinction became clear between copper, lead and zinc (the "urban" metals) on the one hand, and chromium and nickel on the other. Similar results were obtained for the surface (0-10 cm depth) and sub-surface (10-20 cm depth) samples. Comparisons with target or limit concentrations were limited by the existence of different legislation in different countries and the fact that few guidelines deal specifically with public-access urban soils intended for recreational use.     

Unanticipated potential cancer risk near metal recycling facilities

Metal recycling is an important growing industry. Prior to this study, area sources consisting of metal recycling facilities fell in a category of limited regulatory scrutiny because of assumed low levels of annual emissions. Initiating with community complaints of nuisance from smoke, dust and odor, the Houston Department of Health and Human Services (HDHHS) began a monitoring program outside metal recycler facilities and found metal particulates in outdoor ambient air at levels which could pose a carcinogenic human health risk. In a study of five similar metal recycler facilities which used a torch cutting process, air downwind and outside the facility was sampled for eight hours between 6 and 10 times each over 18 months using a mobile laboratory. Ten background locations were also sampled. Iron, manganese, copper, chromium, nickel, lead, cobalt, cadmium and mercury were detected downwind of the metal recyclers at frequencies ranging from 100% of the time for iron to 2% of the time for mercury. Of these metals, chromium, nickel, lead, cobalt, cadmium and mercury were not detected in any sample in the background. Two pairs of samples were analyzed for total chromium and hexavalent chromium to establish a ratio of the fraction of hexavalent chromium in total chromium. This fraction was used to estimate hexavalent chromium at all locations. The carcinogenic risk posed to a residential receptor from metal particulate matter concentrations in the ambient air attributed to the metal recyclers was estimated from each of the five facilities in an effort to rank the importance of this source and inform the need for further investigation. The total risk from these area sources ranged from an increased cancer risk of 1 in 1,000,000 to 6 in 10,000 using the 95th upper confidence limit of the mean of the carcinogenic metal particulate matter concentration, assuming the point of the exposure is the sample location for a residential receptor after accounting for wind direction and the number of shifts that could operate a year. Further study is warranted to better understand the metal air pollution levels in the community and if necessary, to evaluate the feasibility of emission controls and identify operational improvements and best management practices for this industry.This research adds two new aspects to the literature: identification of types and magnitude of metal particulate matter air pollutants associated with a previously unrecognized area source, metal recyclers and their potential risk to health.     

Heavy metals and selenium in feathers of three shorebird species from Delaware bay

Concentrations of lead, cadmium, mercury, selenium, chromium and manganese were examined in breast feathers of shorebirds migrating north through Cape May, New Jersey in 1991 and 1992. Although we predicted that metal levels would be positively correlated with weight, this was only true for mercury in red knots (Calidris canutus). Selenium was negatively correlated with weight in red knots. No other significant correlation of metal concentrations with weight were found. Lead and mercury were highest in sanderlings (C. alba). Selenium and manganese were highest in red knots, while chromium and cadmium levels were highest in semipalmated sandpipers (C. pusilus). For 1991, interspecific metals differences were significant for all metals except lead. For semipalmated sandpipers, cadmium and chromium concentrations were significantly higher in 1991 while managese concentrations were significantly higher in 1992.     

Metals in tissues of fish from Yelkoma Lagoon, northeastern Mediterranean

This study was performed to investigate the metal concentrations in muscle, liver, gonad, and gill of gilthead seabream (Sparus aurata L., 1758), European seabass (Dicentrarchus labrax L., 1758), and keeled mullet (Liza carinata Valenciennes, 1836) from Yelkoma Lagoon, northeastern Mediterranean region. So, the levels of cadmium, cobalt, chromium, copper, iron, manganese, nickel, lead, and zinc in tissues of specimens from the lagoon were determined by inductively coupled plasma optical emission spectrometer. Concentrations of metals in muscles of the examined species ranged from 0.10 to 0.47 mg kg^???1 for cadmium, 0.10 to 0.43 mg kg^???1 for cobalt, 0.17 to 0.72 mg kg^???1 for chromium, 0.62 to 1.03 mg kg^???1 for copper, 28.9 to 52.3 mg kg^???1 for iron, 0.75 to 0.96 mg kg^???1 for manganese, 0.11 to 0.57 mg kg^???1 for nickel, 0.19 to 0.47 mg kg^???1 for lead, and 6.01 to 13.9 mg kg^???1 for zinc, respectively. Additionally, metal concentrations in muscles of fish were assessed for human uses according to provisional tolerable weekly intake and provisional tolerable daily intake.     

Enrichment and fractionation of heavy metals in bed sediments of River Narmada, India

A metal fractionation study on bed sediments of River Narmada in Central India has been carried out to examine the enrichment and partitioning of different metal species between five geochemical phases (exchangeable fraction, carbonate fraction, Fe/Mn oxide fraction, organic fraction and residual fraction). The river receives toxic substances through a large number of tributaries and drains flowing in the catchment of the river. The toxic substances of particular interest are heavy metals derived from urban runoff as well as municipal sewage and industrial effluents. Heavy metals entering the river get adsorbed onto the suspended sediments, which in due course of time settle down in the bottom of the river. In this study fractionation of metal ions has been carried out with the objective to determine the eco-toxic potential of metal ions. Although, in most cases (except iron) the average trace/heavy metal concentrations in sediments were higher than the standard shale values, the risk assessment code as applied to the present study reveals that only about 1–3% of manganese, <1% of copper, 16–19% of nickel, 4–20% of chromium, 1–4% of lead, 8–13% of cadmium and 1–3% of zinc exist in exchangeable fraction and therefore falls under low to medium risk category. According to the Geo-accumulation Index (GAI), cadmium shows high accumulation in the river sediments, rest of other metals are under unpolluted to moderately polluted class.     

西南某省14种尾矿重金属浸出量及总量分析

研究中国西南某省不同类型尾矿的重金属浸出量及总量,为尾矿的污染防范、环境管理和综合利用提供参考和建议。采集了14种类型共164个有代表性尾矿进行浸出毒性试验,并分析其中79个典型尾矿样品的9种重金属含量,以评估其污染风险和综合利用价值。结果表明,有5种类型共7个样品出现浸出毒性超标,分别为铅锌矿、镍矿、银矿、铁矿、锰矿,总体超标率为4.3%。超标元素分别为砷、镉、锌、铅、铜、镍等6种元素,最大超标倍数分别为砷18.3倍、锌4.8倍、镉3.0倍、铅0.56倍、铜0.32倍、镍0.16倍;尾矿含有较多重金属,其中砷、锌、铅、铜含量较高,最高分别达到11.75%、2.60%、1.01%、0.29%,不同类型尾矿其重金属含量各有不同,铅锌矿尾矿的重金属总量最高。总体上,该省绝大多数尾矿为普通固废,少部分为危险废物,砷、镉、锌、铅、铜、镍等6种元素存在污染风险,其中砷元素是最主要污染物;尾矿由于重金属含量较高而有一定的综合利用价值。     

Study on determination of iron,cobalt, nickel,copper, zinc and manganese in drinking water by solid-phase extraction and RP-HPLC with 2-(2-quinolinylazo)-5-diethylaminophenol as precolumn derivatizing reagent

A new method for the determination of iron, cobalt, nickel, copper, zinc and manganese in drinking water by the reversed-phase high-performance liquid chromatography (RP-HPLC) with 2-(2-quinolinylazo)-5-diethylaminophenol (QADEAP) as precolumn derivatizing reagent was studied in this paper. The iron, cobalt, nickel, copper, zinc, and manganese ions react with QADEAP to form color chelates in the presence of cetyl trimethylammonium bromide (CTMAB) and acetic acid-sodium acetic buffer solution medium of pH 4.0. These chelates were enriched by solid-phase extraction with a Waters Nova-Pak C18 cartridge and eluted the retained chelates from the cartridge with tetrahydrofuran (THF). The enrichment factor of 100 was achieved. Then the chelates were separated on a Waters Nova-Pak C18 column (3.9 x 150 mm, 5 microm) by gradient elution with methanol (containing 0.2% of acetic acid and 0.1% of CTMAB) and 0.05 mol L(-1) acetic acid-sodium acetic buffer solution (containing 0.1% of CTMAB) (pH 4.0) as mobile phase at a flow rate of 0.5 ml min(-1), and monitored with a photodiode array detector from 450 approximately 700 nm. The detection limits (S/N = 3) of iron, cobalt, nickel, copper, zinc and manganese are 0.8, 1.1, 0.9, 1.1, 1.5 and 2.0 ng L(-1), respectively, in the original sample. This method can be applied to determination at the microg L(-1) level of iron, cobalt, nickel, copper, zinc and manganese in drinking water with good results.     

密闭微波消解 ICP- AES 法测定大气颗粒物中金属元素

采用过氯乙烯滤膜采集、密闭微波消解、电感耦合等离子发射光谱法测定大气颗粒物中铅、镍、铬、铜、铁、锌、锰、钡、镉,优化了试验条件.方法线性良好,各元素的检出限在0.001 mg/L～0.01 mg/L之间,滤膜样品测定的RSD为0.6%～2.9%,加标回收率为96.0%～105%.     

Mercury and other metals in eggs and feathers of glaucous-winged gulls (Larus glaucescens) in the Aleutians

Levels of mercury and other contaminants should be lower in birds nesting on isolated oceanic islands and at high latitudes without any local or regional sources of contamination, compared to more urban and industrialized temperate regions. We examined concentrations of arsenic, cadmium, chromium, lead, manganese, mercury and selenium in the eggs, and the feathers of fledgling and adult glaucous-winged gulls (Larus glaucescens) nesting in breeding colonies on Adak, Amchitka, and Kiska Islands in the Aleutian Chain of Alaska in the Bering Sea/North Pacific. We tested the following null hypotheses: 1) There were no differences in metal levels among eggs and feathers of adult and fledgling glaucous-winged gulls, 2) There were no differences in metal levels among gulls nesting near the three underground nuclear test sites (Long Shot 1965, Milrow 1969, Cannikin 1971) on Amchitka, 3) There were no differences in metal levels among the three islands, and 4) There were no gender-related differences in metal levels. All four null hypotheses were rejected at the 0.05 level, although there were few differences among the three test sites on Amchitka. Eggs had the lowest levels of cadmium, lead, and mercury, and the feathers of adults had the lowest levels of selenium. Comparing only adults and fledglings, adults had higher levels of cadmium, chromium, lead and mercury, and fledglings had higher levels of arsenic, manganese and selenium. There were few consistent interisland differences, although levels were generally lower for eggs and feathers from gulls on Amchitka compared to the other islands. Arsenic was higher in both adult feathers and eggs from Amchitka compared to Adak, and chromium and lead were higher in adult feathers and eggs from Adak compared to Amchitka. Mercury and arsenic, and chromium and manganese levels were significantly correlated in the feathers of both adult and fledgling gulls. The feathers of males had significantly higher levels of chromium and manganese than did females. The levels of most metals in feathers are below those known to be associated with adverse effects in the gulls or their predators. However, levels of mercury in some gull eggs are within a range suggesting that several eggs should not be eaten in one day by sensitive humans.