Identification of selected hormonally active agents and animal mammary carcinogens in commercial and residential air and dust samples

In order to characterize typical indoor exposures to chemicals of interest for research on breast cancer and other hormonally mediated health outcomes, methods were developed to analyze air and dust for target compounds that have been identified as animal mammary carcinogens or hormonally active agents and that are used in commercial or consumer products or building materials. These methods were applied to a small number of residential and commercial environments to begin to characterize the extent of exposure to these classes of compounds. Phenolic compounds, including nonylphenol, octylphenol, bisphenol A, and the methoxychlor metabolite 2,2-bis(p-hydroxyphenyl)-1,1,1-trichloroethane (HPTE), were extracted, derivatized, and analyzed by gas chromatography/mass spectrometry (GC/MS)-selective ion monitoring (SIM). Selected phthalates, pesticides, polycyclic aromatic hydrocarbons (PAHs), and polychlorinated biphenyls (PCBs) were extracted and analyzed by GC/MS-SIM. Residential and workplace samples showed detectable levels of twelve pesticides in dust and seven in air samples. Phthalates were abundant in dust (0.3-524 micrograms/g) and air (0.005-2.8 micrograms/m3). Nonylphenol and its mono- and di-ethoxylates were prevalent in dust (0.82-14 micrograms/g) along with estrogenic phenols such as bisphenol A and o-phenyl phenol. In this 7-sample pilot study, 33 of 86 target compounds were detected in dust, and 24 of 57 target compounds were detected in air. In a single sample from one home, 27 of the target compounds were detected in dust and 15 in air, providing an indication of chemical mixtures to which humans are typically exposed.     

Survey of phthalates, alkylphenols, bisphenol A and herbicides in Spanish source waters intended for bottling

Background, aim and scope

Groundwaters and source waters are exposed to environmental pollution due to agricultural and industrial activities that can enhance the leaching of organic contaminants. Pesticides are among the most widely studied compounds in groundwater, but little information is available on the presence of phthalates, alkylphenols and bisphenol A. These compounds are used in pesticide formulations and represent an emerging family of contaminants due to their widespread environmental presence and endocrine-disrupting properties. Knowledge on the occurrence of contaminants in source waters intended for bottling is important for sanitary and regulatory purposes. So the aim of the present study was to evaluate the presence of phthalates, alkylphenols, triazines, chloroacetamides and bisphenol A throughout 131 Spanish water sources intended for bottling. Waters studied were spring waters and boreholes which have a protection diameter to minimize environmental contamination.

Materials and methods

Waters were solid-phase extracted (SPE) and analysed by gas chromatography coupled to mass spectrometry (GC-MS). Quality control analysis comprising recovery studies, blank analysis and limits of detection were performed.

Results and discussion

Using SPE and GC-MS, the 21 target compounds were satisfactorily recovered (77?C124?%) and limits of quantification were between 0.0004 and 0.029???g/L for pesticides, while for alkylphenols, bisphenol A and phthalates the limits of quantification were from 0.0018???g/L for octylphenol to 0.970???g/L for bis(2-ethylhexyl) phthalate. Among the 21 compounds analysed, only 9 were detected at levels between 0.002 and 1.115???g/L. Compounds identified were triazine herbicides, alkylphenols, bisphenol A and two phthalates. Spring waters or shallow boreholes were the sites more vulnerable to contaminants. Eighty-five percent of the samples did not contain any of the target compounds.

Conclusions

Target compounds were detected in a very low concentration and only in very few samples. This indicates the good quality of source waters intended for bottling and the effectiveness of the protection measures adopted in Spain. None of the samples analysed exceeded the maximum legislated levels for drinking water both in Spain and in the European Union.     

A national reconnaissance for selected organic micropollutants in sediments on French territory

To collect a large data set regarding the occurrence of organic substances in sediment, this study presents the examination of 20 micropollutants, as a national survey. The list of target compounds contains two alkylphenols, three polycyclic aromatic hydrocarbons (PAHs) not commonly included in monitoring programmes, six pesticides or metabolites, five pharmaceutical compounds, two hormones, one UV filter and bisphenol A. The selective and sensitive analytical methods, based on quick, easy, cheap, effective, rugged, and safe (QuEChERS) sample preparation followed by liquid chromatography-tandem mass spectrometry (LC-MS/MS) or gas chromatography-time-of-flight mass spectrometry (GC-ToF-MS), allow the quantification at limits comprised between 0.5 and 23 ng/g, depending on the compound. The paper summarizes the analytical results from 154 sampling points. Of the 20 target compounds, 9 were determined at least once, and the sediments contained a maximum of 7 substances. The most frequently detected were PAHs (frequency, 77 %; max., 1,400 ng/g). The pharmaceutical compounds, hormones and pesticides were rarely detected in the samples; the most frequently detected was carbamazepine (frequency, 6 %; max., 31 ng/g). In some cases, the levels of PAHs and bisphenol A exceed the predicted no-effect concentration (PNEC) values.     

Sampling and Analysis of Volatile Organic Compounds Evolved During Thermal Processing of Acrylonitrile Butadiene Styrene Composite Resins

Abstract

The evaluation of emissions of volatile organic compounds (VOCs) during processing of resins is of interest to resin manufacturers and resin processors. An accurate estimate of the VOCs emitted from resin processing has been difficult due to the wide variation in processing facilities. This study was designed to estimate the emissions in terms of mass of emitted VOC per mass of resin processed.

A collection and analysis method was developed and validated for the determination of VOCs present in the emissions of thermally processed acrylonitrile butadiene styrene (ABS) resins. Four composite resins were blended from automotive, general molding, pipe, and refrigeration grade ABS resins obtained from the manufacturers. Emission samples were collected in evacuated 6-L Summa canisters and then analyzed using gas chromatography/flame ionization detection/mass selective detection (GC/FID/MSD). Levels were determined for nine target analytes detected in canister samples, and for total VOCs detected by an inline GC/FID. The emissions evolved from the extrusion of each composite resin were expressed in terms of mass of VOCs per mass of processed resin. Styrene was the principal volatile emission from all the composite resins. VOCs analyzed from the pipe resin sample contained the highest level of styrene at 402 μg/g. An additional collection and detection method was used to determine the presence of aerosols in the emissions. This method involved collecting particulates on glass fiber filters, extracting them with solvents, and analyzing them using gas chromatography/mass spectrometry (GC/MS). No significant levels of any of the target analytes were detected on the filters.     

Multiresidue analysis and monitoring of pesticides in rice by pressurized liquid extraction

The aim of this study was to assess the performance of a method of analyzing pesticides in rice by using pressurized liquid extraction (PLE) and to perform a preliminary monitoring by using that method. The instrumental quantification limit, instrumental detection limit, method quantification limit, and method detection limit were determined. PLE temperature was also optimized for 6 target pesticides. Mean recoveries of spiked rice with target pesticides (4 ng/g and 40 ng/g) were 83%–109% with the repeatability of the analysis, represented as relative standard deviations, ranged from 1.3% to 11% (n = 5) for PLE at 130°C. These results were satisfactory according to the method of positive list in Japan. In a preliminary analysis of 10 target pesticides in 54 commercial rice samples, ferimzone was detected in only one unpolished rice sample.     

Determination of phenols and pharmaceuticals in municipal wastewaters from Polish treatment plants by ultrasound-assisted emulsification–microextraction followed by GC–MS

A method combining ultrasound-assisted emulsification–microextraction (USAEME) with gas chromatography–mass spectrometry (GC–MS) was developed for simultaneous determination of four acidic pharmaceuticals, ibuprofen, naproxen, ketoprofen, and diclofenac, as well as four phenols, 4-octylphenol, 4-n-nonylphenol, bisphenol A, and triclosan in municipal wastewaters. Conditions of extraction and simultaneous derivatization were optimized with respect to such aspects as type and volume of extraction solvent, volume of derivatization reagent, kind and amount of buffering salt, location of the test tube in the ultrasonic bath, and extraction time. The average correlation coefficient of the calibration curves was 0.9946. The LOD/(LOQ) values in influent and effluent wastewater were in the range of 0.002–0.121/(0.005–0.403) μg L^?1 and 0.002–0.828/(0.006–2.758) μg L^?1, respectively. Quantitative recoveries (≥94 %) and satisfactory precision (average RSD 8.2 %) were obtained. The optimized USAEME/GC–MS method was applied for determination of the considered pharmaceuticals and phenols in influents and treated effluents from nine Polish municipal wastewater treatment plants. The average concentration of acidic pharmaceuticals in influent and effluent wastewater were in the range of 0.06–551.96 μg L^?1 and 0.01–22.61 μg L^?1, respectively, while for phenols were in the range of 0.03–102.54 μg L^?1 and 0.02–10.84 μg L^?1, respectively. The removal efficiencies of the target compounds during purification process were between 84 and 99 %.     

Determination of organochlorine and organophosphate pesticide residues in fruits,vegetables and sediments

Abstract

A method is described for the determination of organochlorine and organophosphate pesticide residues in fruits, vegetables and sediments. The concentrated solvent extract was sealed in a polymeric membrane tube, dialysed in cyclohexane and the solvent replaced with hexane. The organophosphates were analysed on a specific thermionic detector without further clean‐up. For the organochlorine pesticides the extract was eluted through 3 g of alumina and analysed on GC/ECD. The clean‐up for sediment extract was carried out on a10 g alumina column with 100 mL hexane containing 5% acetone and the eluate was concentrated to 5 mL.

The detection limit for organophosphates on a 40 g sample and a final volume of 10 mL was on the average 0.01 mg/kg. The detection limit for organochlorine pesticides, with the final volume of 25 mL, was 0.005 mg/kg for all pesticides except for p,p'‐DDT and endosulfan sulphate, which was 0.01 mg/kg.

The detection limit for oganochlorine pesticides in sediment, with the final volume of 2 mL, was less than 1 μg/kg and for organophosphate pesticides less than 10 μg/kg when the final volume was made to 0.5 mL. At the detection limits the method produced a very high coefficient of variation for both organochlorine and organophosphate pesticides.     

PESTICIDE RESIDUES IN THERMAL MINERAL WATER IN GREECE

Eight different hot springs (SPA) in Greece were monitored over a one-year survey for priority pesticide residues. A specific and effective procedure including solid phase extraction in combination with HPLC and GC analytical methods were applied. Samples that were sensitive to nitrogen-phosphorus (NPD) and/or electron capture (ECD) detectors were analysed by capillary gas chromatography.

From the twenty-six water samples, pesticide residues were detected in fourteen of them (54%) but no one exceeding the European Union Maximum Acceptable Concentration (MAC).

Lindane (γ-BHC) was the most frequently detected pesticide. It was found in nine samples (35%) in concentrations from <0.005 to 0.01 μg/L. Other pesticides detected were phorate (in five samples), propachlor (in two samples) and chlorpyriphos ethyl (in three samples) but in concentrations far below the permissible levels.     

Comparisons of the Dust/Smoke Particulate that Settled Inside the Surrounding Buildings and Outside on the Streets of Southern New York City after the Collapse of the World Trade Center,September 11, 2001

Abstract

The collapse of the World Trade Center (WTC) on September 11, 2001, generated large amounts of dust and smoke that settled in the surrounding indoor and outdoor environments in southern Manhattan. Sixteen dust samples were collected from undisturbed locations inside two uncleaned buildings that were adjacent to Ground Zero. These samples were analyzed for morphology, metals, and organic compounds, and the results were compared with the previously reported outdoor WTC dust/smoke results. We also analyzed seven additional dust samples provided by residents in the local neighborhoods. The morphologic analyses showed that the indoor WTC dust/smoke samples were similar to the outdoor WTC dust/smoke samples in composition and characteristics but with more than 50% mass in the <53 μm size fraction. This was in contrast to the outdoor samples that contained >50% of mass above >53 μm. Elemental analyses also showed the similarities, but at lower concentrations. Organic compounds present in the outdoor samples were also detected in the indoor samples. Conversely, the resident-provided convenience dust samples were different from either the WTC indoor or outdoor samples in composition and pH, indicating that they were not WTC-affected locations. In summary, the indoor dust/smoke was similar in concentration to the outdoor dust/smoke but had a greater percentage of mass <53 μm in diameter.     

Characterization of trace organic contaminants in marine sediment from Yeongil Bay, Korea: 1. Instrumental analyses

Concentrations of polychlorinated biphenyls (PCBs), organochlorine (OC) pesticides (HCB, HCHs, CHLs, and DDTs), polycyclic aromatic hydrocarbons (PAHs), alkylphenols (APs), and bisphenol A (BPA) were measured in 26 marine sediments collected from Yeongil Bay, Korea, in order to characterize their spatial distribution and sources. PCBs (2.85-26.5 ng/g, dry wt.) were detected mainly in the inner bay locations Mean OC pesticide ranged from 1.16 ng/g dry wt. for HCH to 0.05 ng/g dry wt. for HCB). PAH concentrations ranged from <10.0 to 1870 (mean: 309)ng/g dry wt., and were predominated 3- and 4-ring congeners. Concentrations of APs, such as nonylphenol, octylphenol, butylphenol (means 89.1, 4.61, 11.0 ng/g dry wt., respectively), were greater at locations proximal to municipal wastewater discharges. Concentrations of PCBs and PAHs were great near shipyards and industrial complexes. Vertical profiles of PAHs and APs indicated that they have been associated with sediments since the 1950s.     

Determination of atrazine in rainfall and surface water by enzyme immunoassay

Rainwater and surface water from four sites in Germany (Bavaria and Lower Saxony) were analyzed for atrazine by enzyme immunoassay from June 1990 until October 1992. The limit of quantification of the immunoassay was 0.02 μg/L with a middle of the test at 0.2 μg/L. About 60 % of the samples contained measurable amounts of atrazine. Seasonal trends were observed, with the highest concentration in the summer months of up to 4 μg/L for rainwater and up to 15 μg/L for surface waters. The highest concentrations were found in agricultural areas, while in the investigated national parks up to 0.56 μg/L could be detected in rain water. This points to long-range atmospheric transport from agricultural areas to pristine national parks. Samples from forest stands usually showed higher atrazine concentrations than samples from open fields. Deposition rates of 10 – 50 μg/m² · yr were observed in the national parks and 10–180 μg/m² · yr at the agricultural sites. Comparison of results obtained by enzyme immunoassay and GC/MS showed a good correlation of r = 0.95.     

Temporal variations of fine and coarse particulate matter sources in Jeddah,Saudi Arabia

This study provides the first comprehensive analysis of the seasonal variations and weekday/weekend differences in fine (aerodynamic diameter <2.5 μm; PM_2.5) and coarse (aerodynamic diameter 2.5–10 μm; PM_2.5–10) particulate matter mass concentrations, elemental constituents, and potential source origins in Jeddah, Saudi Arabia. Air quality samples were collected over 1 yr, from June 2011 to May 2012 at a frequency of three times per week, and analyzed. The average mass concentrations of PM_2.5 (21.9 μg/m³) and PM₁₀ (107.8 μg/m³) during the sampling period exceeded the recommended annual average levels by the World Health Organization (WHO) for PM_2.5 (10 μg/m³) and PM₁₀ (20 μg/m³), respectively. Similar to other Middle Eastern locales, PM_2.5–10 is the prevailing mass component of atmospheric particulate matter at Jeddah, accounting for approximately 80% of the PM₁₀ mass. Considerations of enrichment factors, absolute principal component analysis (APCA), concentration roses, and backward trajectories identified the following source categories for both PM_2.5 and PM_2.5–10: (1) soil/road dust, (2) incineration, and (3) traffic; and for PM_2.5 only, (4) residual oil burning. Soil/road dust accounted for a major portion of both the PM_2.5 (27%) and PM_2.5–10 (77%) mass, and the largest source contributor for PM_2.5 was from residual oil burning (63%). Temporal variations of PM_2.5–10 and PM_2.5 were observed, with the elevated concentration levels observed for mass during the spring (due to increased dust storm frequency) and on weekdays (due to increased traffic). The predominant role of windblown soil and road dust in both the PM_2.5 and PM_2.5–10 masses in this city may have implications regarding the toxicity of these particles versus those in the Western world where most PM health assessments have been made in the past. These results support the need for region-specific epidemiological investigations to be conducted and considered in future PM standard setting.

Implications: Temporal variations of fine and coarse PM mass, elemental constituents, and sources were examined in Jeddah, Saudi Arabia, for the first time. The main source of PM_2.5–10 is natural windblown soil and road dust, whereas the predominant source of PM_2.5 is residual oil burning, generated from the port and oil refinery located west of the air sampler, suggesting that targeted emission controls could significantly improve the air quality in the city. The compositional differences point to a need for health effect studies to be conducted in this region, so as to directly assess the applicability of the existing guidelines to the Middle East air pollution.     

Selected organochlorine pesticide and polychlorinated biphenyl residues in house dust in Singapore

Although the use of organochlorine pesticides (OCPs) and polychlorinated biphenyls (PCBs) has been prohibited in Singapore since 1980, OCPs and PCBs still can be detected in the environment and represent a potential threat to public health. In this study, OCPs and PCBs were measured in house dust samples collected from 31 homes across the island-state of Singapore. Organochlorine pesticides, such as hexachlorocyclohexanes (HCHs), chlordanes and dichlorodiphenyltrichloroethanes (DDTs) were tested, with a range of 相似文献   

Particulate and Nicotine Sampling in Public Facilities and Offices

Abstract

The purpose of this study was to characterize and measure indoor air quality in public facilities and office buildings. The pollutants of interest were particulate matter smaller than 2.5 μm in diameter, PM-2.5, and environmental tobacco smoke (ETS). Integrated PM- 2.5 samples were taken on Teflon membrane filters using Harvard Aerosol Impactors as a pre-size selector. Filters were analyzed by gravimetric analysis. Nicotine, which was used as a marker for ETS, was collected on sodium-bisulfate-impregnated, glass-fiber filters and was analyzed by gas chromatography. Twenty-one structures were monitored in Metropolitan Boston. Measured particle concentrations ranged from 6.0 μg/m³ to about 550 μg/m³. Nicotine concentrations were as high as 26 μg/m³ in a designated smoking room. Real-time measurements were also taken using two types of nephelometers; a Handheld Aerosol Monitor (HAM) and a Miniature Real-Time Aerosol Monitor (MINIRAM). Short-term field measurements with these instruments correlated better with the integrated PM-2.5 concentrations in smoking locations than with concentrations in non-smoking areas.     

Cost and Benefits of Road Dust Control in Seattle’s Industrial Valley

The paving of gravel roads with an average daily traffic (ADT) over 15 is a least cost method for reducing suspended particulate In the air in Seattle. It is also a good business investment when the ADT exceeds 100. Clean roads, gutters, and parking lots may reduce or eliminate Seattle’s most serious environmental constraint on economic development. In a study done in Seattle’s Duwamish Valley the impact of road dust on air quality was measured by obtaining dust emission factors for vehicles traveling at 10, 20, and 30 mph on gravel as well as dusty paved roads. A University of Washington Mark II Cascade Impactor was mounted on a trailer and towed behind a car to determine the concentration and size distribution of this dust. It was found that each vehicle mile at 20 mph on unpaved roads contributed 7.0 Ib of dust to the air, 1.9 Ib consisting of particles smaller than 10 microns in diameter and 0.24 Ib below 2 microns. Three to eight percent by weight of this respirable dust was free silica, which is potentially toxic. The quantity of dust generated varies as an exponent of the speed. The concentrations of dust found in the air near a dry gravel road with an ADT of 250 reached 584 μg/m3 for an 8 hr work day. A 24 hr suspended particulate reading of 463 μg/m3 total and 3.83 μg/m3 free silica was found beside a dusty paved road with an ADT of 18,000. Nineteen miles of gravel roads and 110 miles of dusty paved roads contributed 2700 tons/year of particulate, of which 700 tons were below 10 microns. Paving or oiling such roads will produce benefits of $3,881,000 yearly in household cleaning, health care, sewer, vehicle operation, and road maintenance costs as well as an increase in property values. Clean roads can lower the cost of clean air in Seattle.     

Evaluation of atrazine positive and false positive immunoassay detections in ground water

Abstract

False positive responses on an atrazine (6‐chloro‐N‐ethyl‐N'‐(l‐methylethyl)‐1, 3, 5‐triazine‐2, 4‐diamine) immunoassay kit were investigated to explain possible causes for these occurences. Ground water samples were evaluated with the immunoassay kit and positive responses (>0.20 μg L^‐1) were confirmed using gas chromatography/mass spectrometry (GC/MS). Non‐confirming samples (false positives) were analyzed for seven additional compounds on GC. Resulting GC/MS and GC analyses showed that 70% of the false positives could be attributed to two compounds. Prometon (6‐methoxy‐N,N'‐bis(l‐methylethyl)‐1, 3, 5‐triazine‐2, 4‐diamine) was responsible for the majority (64%) of the false positive responses The atrazine metabolite, deethylatrazine (2‐chloro‐4‐amino‐6‐isopropylamino‐1, 3, 5‐triazine), was responsible for the other 6% of the false positives measured. Unattributed false positives (30%) were probably due to an overestimation of pesticide concentrations in the kit's lower detection range.     

Bioanalytical characterisation of multiple endocrine- and dioxin-like activities in sediments from reference and impacted small rivers

A comprehensive evaluation of organic contamination was performed in sediments sampled in two reference and three impacted small streams where endocrine disruptive (ED) effects in fish have been evidenced. The approach combined quantitative chemical analyses of more than 50 ED chemicals (EDCs) and a battery of in vitro bioassays allowing the quantification of receptor-mediated activities, namely estrogen (ER), androgen (AR), dioxin (AhR) and pregnane X (PXR) receptors. At the most impacted sites, chemical analyses showed the presence of natural estrogens, organochlorine pesticides, parabens, polycyclic aromatic hydrocarbons (16 PAHs), bisphenol A and alkylphenols, while synthetic steroids, myco-estrogens and phyto-estrogens were not detected. Determination of toxic-equivalent amounts showed that 28-96% of estrogenic activities in bioassays (0.2-6.3 ng/g 17β-estradiol equivalents) were explained by 17β-estradiol and estrone. PAHs were major contributors (20-60%) to the total dioxin-like activities. Interestingly, high PXR and (anti)AR activities were detected; however, the targeted analysed compounds could not explain the measured biological activities. This study highlighted the presence of multiple organic EDCs in French river sediments subjected to mixed diffuse pollution, and argues for the need to further identify AR and PXR active compounds in the aquatic environment.     

Levels of Persistent Organochlorine Residues in Eggs of Greater Flamingos from the Guadalquivir Marshes (Doñana), Spain

Organochlorine pesticides (OCPs) and polychlorinated biphenyls (PCBs) residue levels were determined in 53 unhatched eggs from greater roseus flamingos (Phoenicopterus ruber). Eggs were collected in 1996 from the National Park of Doñana (Guadalquivir marshes, Southwest Spain), immediately after one breeding colony abandoned the nesting site due to predator attacks. The main metabolite of p,p′-DDT, p,p′-DDE, was the OCP residue found at higher concentrations, with a geometric mean of 721 ng/g wet weight. Residues of other pesticides, including some hexachlorocyclohexane isomers, hexachlorobenzene, aldrin, heptachlor, and heptachlor-epoxide, were detected at much lower concentrations. The sum of PCBs was 528 ng/g, with PCB congeners #187 and #153 being the most prominent in eggs. The pattern observed in these compounds of industrial origin corresponded more to Aroclor 1260 than to any other commercial mixture. Levels of organochlorine residues indicate a medium degree of exposure, and they are not considered of any concern for the flamingo population. In particular, neither p,p′-DDE nor PCB levels were found to be correlated with the eggshell thickness.     

Occurrence of pesticides and polychlorinated biphenyls in water of the Nile river at the estuaries of Rosetta and Damiatta branches,north of delta,Egypt

Abstract

A study was conducted from summer 1995 to summer 1997 to assess the seasonal occurrence of pesticide residues and other organic contaminants, polychlorinated biphenyls (PCBs), in water at the estuaries of Rosetta and Damiatta branches of the Nile river. The results indicated that organochlorine compounds (OCs) including HCB, lindane, p,p‘‐DDE, p,p‘DDD, p,p‘‐DDT, aroclor 1254 and aroclor 1260 were present in all the water samples at concentration levels ranging between 0.195–0.240, 0.286–0.352, 0.035–0.067, 0.019–0.033, 0.024–0.031, 0.390–0.70 and 0.166–0.330 μg/l, respectively. The levels of these compounds were higher in water of Damiatta branch than those found in water of Rosetta branch. Aldrin, dieldrin and endrin were not detected in all water samples. Only 4 compounds from 36 organophosphorus insecticides, fungicides and s‐triazine herbicides tested were detected in water samples collected during summer and autumn seasons from Rosetta branch. The concentration levels of these detected compounds, dimethoate, malathion, captan, and ametryne, ranged from 0.011 to 0.340 μg/l, respectively. Similar compounds during the same seasons as found in water of Rosetta branch were also detected in water of Damiatta branch except ametryne. The levels of the detected compounds (dimethoate, malathion and captan) ranged between 0.030 and 0.330 μg/l. The levels of detected organophosphorus insecticides, fungicides and s‐triazine herbicides were in the order: dimethoate > malathion > captan > ametryne.     

PM10 concentration levels at an urban and background site in Cyprus: The impact of urban sources and dust storms

Air quality in Cyprus is influenced by both local and transported pollution, including desert dust storms. We examined PM₁₀ concentration data collected in Nicosia (urban representative) from April 1, 1993, through December 11, 2008, and in Ayia Marina (rural background representative) from January 1, 1999, through December 31, 2008. Measurements were conducted using a Tapered Element Oscillating Micro-balance (TEOM). PM₁₀ concentrations, meteorological records, and satellite data were used to identify dust storm days. We investigated long-term trends using a Generalized Additive Model (GAM) after controlling for day of week, month, temperature, wind speed, and relative humidity. In Nicosia, annual PM₁₀ concentrations ranged from 50.4 to 63.8 μg/m³ and exceeded the EU annual standard limit enacted in 2005 of 40 μg/m³ every year. A large, statistically significant impact of urban sources (defined as the difference between urban and background levels) was seen in Nicosia over the period 2000–2008, and was highest during traffic hours, weekdays, cold months, and low wind conditions. Our estimate of the mean (standard error) contribution of urban sources to the daily ambient PM₁₀ was 24.0 (0.4) μg/m³. The study of yearly trends showed that PM₁₀ levels in Nicosia decreased from 59.4 μg/m³ in 1993 to 49.0 μg/m³ in 2008, probably in part as a result of traffic emission control policies in Cyprus. In Ayia Marina, annual concentrations ranged from 27.3 to 35.6 μg/m³, and no obvious time trends were observed. The levels measured at the Cyprus background site are comparable to background concentrations reported in other Eastern Mediterranean countries. Average daily PM₁₀ concentrations during desert dust storms were around 100 μg/m³ since 2000 and much higher in earlier years. Despite the large impact of dust storms and their increasing frequency over time, dust storms were responsible for a small fraction of the exceedances of the daily PM₁₀ limit.

ImplicationsThis paper examines PM₁₀ concentrations in Nicosia, Cyprus, from 1993 to 2008. The decrease in PM₁₀ levels in Nicosia suggests that the implementation of traffic emission control policies in Cyprus has been effective. However, particle levels still exceeded the European Union annual standard, and dust storms were responsible for a small fraction of the daily PM₁₀ limit exceedances. Other natural particles that are not assessed in this study, such as resuspended soil and sea salt, may be responsible in part for the high particle levels.