Source identification and trends in concentrations of gaseous and fine particulate principal species in Seoul, South Korea

Ambient measurements were made using two sets of annular denuder system during the four seasons (April 2001 to February 2002) and were then compared with the results during the period of 1996-1997 to estimate the trends and seasonal variations in concentrations of gaseous and fine particulate matter (PM2.5) principal species. Annual averages of gaseous HNO3 and NH3 increased by 11% and 6%, respectively, compared with those of the previous study, whereas HONO and SO2 decreased by 11% and 136%, respectively. The PM2.5 concentration decreased by -17%, 35% for SO4(2-), and 29% for NH4+, whereas NO3- increased by 21%. Organic carbon (OC) and elemental carbon (EC) were 12.8 and 5.98 microg/m(-3), accounting for -26 and 12% of PM2.5 concentration, respectively. The species studied accounted for 84% of PM2.5 concentration, ranging from 76% in winter to 97% in summer. Potential source contribution function (PSCF) analysis was used to identify possible source areas affecting air pollution levels at a receptor site in Seoul. High possible source areas in concentrations of PM2.5, NO3-, SO4(2-), NH4+, and K+ were coastal cities of Liaoning province (possibly emissions from oil-fired boilers on ocean liners and fishing vessels and industrial emissions), inland areas of Heibei/Shandong provinces (the highest density areas of agricultural production and population) in China, and typical port cities (Mokpo, Yeosu, and Busan) of South Korea. In the PSCF map for OC, high possible source areas were also coastal cities of Liaoning province and inland areas of Heibei/Shandong provinces in China. In contrast, high possible source areas of EC were highlighted in the south of the Yellow Sea, indicating possible emissions from oil-fired boilers on large ships between South Korea and Southeast Asia. In summary, the PSCF results may suggest that air pollution levels in Seoul are affected considerably by long-range transport from external areas, such as the coastal zone in China and other cities in South Korea, as well as Seoul itself.     

PM2.5 particles and size-segregated ionic species measured during fall season in three urban sites in Korea

Twelve hours integrated fine particles (PM_2.5) and 24-h average size-segregated particles were collected to investigate the chemical characteristics and to determine the size distribution of ionic species during October–December 1999 in three cities of different urban scale; Chongju, Kwangju, and Seoul, Korea. Concentrations of 5-min PM_2.5 black carbon (BC) and hourly criteria air pollutants (PM₁₀, CO, NO_x, SO₂, and O₃) were also measured using the Aethalometer and ambient air monitoring system, respectively.Highest PM_2.5 mass concentrations at Chongju, Kwangju, and Seoul sites were 63.0, 77.9, and 143.7 μg m⁻³, respectively. For the time period when highest PM_2.5 mass occurred, BC level out of PM_2.5 chemical species was highest at both Chongju and Kwangju, and highest NO₃⁻ (23.6 μg m⁻³) followed by BC (23.1 μg m⁻³) were observed at Seoul site, indicating that highest PM_2.5 pollution is closely associated with the traffic emissions. Strong relationships of Fe with BC and Zn at both Kwangju and Seoul sites support that the Fe and Zn measured there are originated partly from same source as BC, i.e. diesel traffics. However, it is suggested that the Fe measured at Chongju is most likely derived from dispersion of soil dust.The size distributions of SO₄²⁻, NO₃⁻, and NH₄⁺ ionic species indicated similar unimodal distributions at all sampling sites. However, different unimodal patterns in the accumulation mode size range with a peak in the smaller size (0.28–0.53 μm, condensation mode) in both Kwangju and Seoul, and in the relatively larger size (0.53–1.0 μm, droplet mode) in Chongju, were found. The potassium ion under the study sites dominates in the fine mode, and its size distribution showed unimodal character with a maximum in the size range 0.56–1.0 μm.     

Major ionic compositions of fine particulate matter in an animal feeding operation facility and its vicinity

Animal feeding operations (AFOs) produce particulate matter (PM) and gaseous pollutants. Investigation of the chemical composition of PM_2.5 inside and in the local vicinity of AFOs can help to understand the impact of the AFO emissions on ambient secondary PM formation. This study was conducted on a commercial egg production farm in North Carolina. Samples of PM_2.5 were collected from five stations, with one located in an egg production house and the other four located in the vicinity of the farm along four wind directions. The major ions of NH₄⁺, Na⁺, K⁺, SO₄^2?, Cl^?, and NO₃^? were analyzed using ion chromatography (IC). In the house, the mostly abundant ions were SO₄^2?, Cl^?, and K⁺. At ambient stations, SO₄^2?, and NH₄⁺ were the two most abundant ions. In the house, NH₄⁺, SO₄^2?, and NO₃^? accounted for only 10% of the PM_2.5 mass; at ambient locations, NH₄⁺, SO₄^2?, and NO₃^? accounted for 36–41% of the PM_2.5 mass. In the house, NH₄⁺ had small seasonal variations indicating that gas-phase NH₃ was not the only major force driving its gas–particle partitioning. At the ambient stations, NH₄⁺ had the highest concentrations in summer. In the house, K⁺, Na⁺, and Cl^? were highly correlated with each other. In ambient locations, SO₄^2? and NH₄⁺ had a strong correlation, whereas in the house, SO₄^2? and NH₄⁺ had a very weak correlation. Ambient temperature and solar radiation were positively correlated with NH₄⁺ and SO₄^2?. This study suggests that secondary PM formation inside the animal house was not an important source of PM_2.5. In the vicinity, NH₃ emissions had greater impact on PM_2.5 formation.

ImplicationsThe chemical composition of PM_2.5 inside and in the local vicinity of AFOs showed the impact of the AFO emissions on ambient secondary PM_2.5 formation, and the fate and transport of air pollutants associated with AFOs. The results may help to manage in-house animal facility air quality, and to develop regional air quality control strategies and policies, especially in animal agriculture-concentrated areas.     

Seasonal variations of acidic air pollutants in Seoul,South Korea

The annular denuder system (ADS) was used to characterize seasonal variations of acidic air pollutants in Seoul, South Korea. Fifty- four 24 h samples were collected over four seasons from October 1996 to September 1997. The annual mean concentrations of HNO₃, HNO₂, SO₂ and NH₃ in the gas phase were 1.09, 4.51, 17.3 and 4.34 μg m^-3, respectively. The annual mean concentrations of PM_2.5(d_p≤2.5 μm in aerodynamic diameter, 50% cutoff), SO^2-₄, NO^-₃ and NH⁺₄ in the particulate phase were 56.9, 8.70, 5.97 and 4.19 μg m^-3, respectively. All chemical species monitored from this study showed statistical seasonal variations. Nitric acid (HNO₃) and ammonia (NH₃) exhibited substantially higher concentrations during the summer, while nitrous acid (HNO₂) and sulfur dioxide(SO₂) were higher during the winter. Concentrations of PM_2.5, SO^2-₄, NO^-₃ and NH⁺₄ in the particulate phase were higher during the winter months. SO^2-₄, NO^-₃ and NH⁺₄ accounted for 26–38% of PM_2.5. High correlations were found among PM_2.5, SO^2-₄, NO^-₃ and NH⁺₄. The mean H⁺ concentration measured only in the fall was 5.19 nmole m^-3.     

The use of real-time monitoring data to evaluate major sources of airborne particulate matter

Real-time chemical measurements have been made as part of a field study of air quality in the city and harbour of Cork, Ireland. The data relate to the year 2008, with particular attention paid to the period between May and August. Eight air quality parameters were measured: NO, O₃, NO₂, SO₂, EC, OC, particulate SO₄^2? and PM_2.5. The data have been used in a novel way involving wind and temporal averaging, along with Principal Component Analysis (PCA) and Positive Matrix Factorisation (PMF) methodologies to extrapolate major source contributions for PM_2.5. It is demonstrated that continuous monitoring of standard air quality parameters, such as NO, NO₂, SO₂, along with EC, OC and particulate SO₄^2?, can be used to provide relevant, cost-effective initial estimates of source contributions to ambient PM_2.5 levels. It is also shown that the benefit of including OC and particulate SO₄^2? in the monitoring protocol is considerable. Three major source groups of ambient PM_2.5 mass in Cork were identified and quantified using this combined monitoring and modelling approach; road transport (19%), domestic solid fuel burning (14%) and oil-fired domestic and industrial boilers, including power generation plants (31%).     

PM composition and source reconciliation in Mexico City

PM_2.5 and PM₁₀ were collected during 24-h sampling intervals from March 1st to 31st, 2006 during the MILAGRO campaign carried out in Mexico City's northern region, in order to determine their chemical composition, oxidative activity and the estimation of the source contributions during the sampling period by means of the chemical mass balance (CMB) receptor model. PM_2.5 concentrations ranged from 32 to 70 μg m⁻³ while that of PM10 did so from 51 to 132 μg m⁻³. The most abundant chemical species for both PM fractions were: OC, EC, SO₄²⁻, NO₃⁻, NH₄⁺, Si, Fe and Ca. The majority of the PM mass was comprised of carbon, up to about 52% and 30% of the PM2.5 and PM10, respectively. PM2.5 constituted more than 50% of PM10. The redox activity, assessed by the dithiothreitol (DTT) assay, was greater for PM_2.5 than for PM₁₀, and did not display significant differences during the sampling period. The PM_2.5 source reconciliation showed that in average, vehicle exhaust emissions were its most important source in an urban site with a 42% contribution, followed by re-suspended dust with 26%, secondary inorganic aerosols with 11%, and industrial emissions and food cooking with 10% each. These results had a good agreement with the Emission Inventory. In average, the greater mass concentration occurred during O₃S that corresponds to a wind shift initially with transport to the South but moving back to the North. Taken together these results show that PM chemical composition, oxidative potential, and source contribution is influenced by the meteorological conditions.     

The Steubenville Comprehensive Air Monitoring Program (SCAMP): Concentrations and Solubilities of PM2.5 Trace Elements and Their Implications for Source Apportionment and Health Research

Abstract

The elemental compositions of the water-soluble and acid-digestible fractions of 24-hr integrated fine particulate matter (PM_2.5) samples collected in Steubenville, OH, from 2000 to 2002 were determined using dynamic reaction cell inductively coupled plasma-mass spectrometry. The water-soluble elemental compositions of PM_2.5 samples collected at four satellite monitoring sites in the surrounding region were also determined. Fe was the most abundant but least water soluble of the elements determined at the Steubenville site, having a mean ambient concentration of 272 µg/m³ and a median fractional solubility of 6%. Fe solubility and its correlations with SO₄ ^2? and temperature varied significantly by season, consistent with the hypothesis that secondary sulfates may help to mobilize soluble Fe under suitable summertime photochemical conditions. Significantly higher ambient concentrations were observed at Steubenville than at each of the four satellite sites for 10 of the 18 elements (Al, As, Ca, Cd, Fe, Mg, Mn, Na, Pb, and Zn) determined in the water-soluble PM_2.5 fraction. Concentrations of Fe, Mn, and Zn at Steubenville were substantially higher than concentrations reported recently for larger U.S. cities. Receptor modeling identified seven sources affecting the Steubenville site. An (NH₄)₂SO₄-dominated source, likely representing secondary PM_2.5 from coal-fired plants to the west and southwest of Steubenville, accounted for 42% of the PM_2.5 mass, and two sources likely dominated by emissions from motor vehicles and from iron and steel facilities in the immediate Steubenville vicinity accounted for 20% and 10%, respectively. Other sources included an NH₄NO₃ source (15%), a crustal source (6%), a mixed nonferrous metals and industrial source (3%), and a primary coal combustion source (3%). Results suggest the importance of very different regional and local source mechanisms in contributing to PM_2.5 mass at Steubenville and reinforce the need for further research to elucidate whether metals such as Fe, Mn, and Zn play a role in the PM_2.5 health effects observed previously there.     

PM2.5–10, PM2.5 and associated water-soluble inorganic species at a coastal urban site in the metropolitan region of Rio de Janeiro

The concentrations of PM_2.5−10, PM_2.5 and associated water-soluble inorganic species (WSIS) were determined in a coastal site of the metropolitan region of Rio de Janeiro, Southeastern Brazil, from October 1998 to September 1999 (n=50). Samples were dissolved in water and analyzed for major inorganic ions. The mean (± standard deviation; median) concentrations of PM_2.5−10 and PM_2.5 were, respectively, 26 (± 16; 21) μg m⁻³ and 17 (± 13; 14) μg m⁻³. Their mean concentrations were 1.7–1.8 times higher in dry season (May–October) than in rainy season (November–April). The WSIS comprised, respectively, 34% and 28% of the PM_2.5−10 and PM_2.5 masses. Chloride, Na⁺ and Mg²⁺ were the predominant ions in PM_2.5−10, indicating a significant influence of sea-salt aerosols. In PM_2.5, SO₄²⁻ (∼97% nss-SO₄²⁻) and NH₄⁺ were the most abundant ions and their equivalent concentration ratio (SO₄²⁻/NH₄⁺ ∼1.0) suggests that they were present as (NH₄)₂SO₄ particles. The mean concentration of (NH₄)₂SO₄ was 3.4 μg m⁻³. The mean equivalent PM_2.5 NO₃⁻ concentration was eight times smaller than those of SO₄²⁻ and NH₄⁺. The PM_2.5 NO₃⁻ concentration in dry season was three times higher than in rainy season, probably due to reaction of NaCl (sea salt) with HNO₃ as a result of higher levels of NO_y during the dry season and/or reduced volatilization of NH₄NO₃ due to lower wintertime temperature. Chloride depletion was observed in both size ranges, although more pronouncely in PM_2.5.     

Seasonal variation of ionic species in fine particles at Qingdao,China

Totally nine measurement campaigns for ambient particles and SO₂ have been conducted during the period of 1997–2000 in Qingdao in order to understand the characteristics of the particulate matter in coastal areas of China. The mass fractions of PM_2.5, PM_2.5−10 and PM_>10 in TSP are 49%, 25% and 26%, respectively. The size distribution of particles mass concentrations in Qingdao shows bi-modal distribution. Mass fraction percentages of water-soluble ions in PM_2.5, PM_2.5−10 and PM_>10 decreased from 62% to 35% and 21%. In fine particles, sulfate, nitrate and ammonium, secondary formed compounds, are major components, totally accounting for 50% of PM_2.5 mass concentration.The ratios of sulfate, chloride, ammonium and potassium in PM_2.5 for heating versus non-heating periods are 1.34, 1.80, 1.56 and 1.44, respectively. The ratio of nitrate is 3.02 and this high ratio could be caused by reduced volatilization at lower temperature. Sulfate concentrations are higher than nitrate in PM_2.5. The chemical forms of sulfate and nitrate are probably (NH₄)₂SO₄ and NH₄NO₃ and chloride depletion was observed.Backward trajectory analysis reflected possible influence of air pollutant transport to Qingdao local aerosol pollution.     

Health effects of PM2.5 constituents and source contributions in major metropolitan cities,South Korea

Ambient PM_2.5 is one of the major risk factors for human health, and is not fully explained solely by mass concentration. We examined the short-term associations of cause-specific mortality (i.e., all-cause, cardiovascular, and respiratory mortality) with the 15 chemical constituents and sources of PM_2.5 in four metropolitan cities of South Korea during 2014–2018. We found transition metals consistently showed significant associations with all-cause mortality, while the effects of other constituents varied across the cities and for cause of death. Carbonaceous components strongly affected the all-cause, cardiovascular, and respiratory mortality in Daejeon. Secondary inorganic aerosols, SO₄^2? and NH₄⁺, showed significant associations with respiratory mortality in Gwangju. We also found the sources from which species closely linked to mortality generally increased the relative mortality risks. Heavy metal markers from soil or industrial sources were significantly associated with mortality in all cities. However, several sources influenced mortality despite their marker species not being significantly associated with it. Secondary nitrate and secondary sulfate sources were linked to mortality in DJ. This could be attributed to the deep inland location, which might have facilitated formation of secondary inorganic aerosols. In addition, primary sources including mobile and coal combustion seemed to have acute impacts on respiratory mortality in Gwangju. Our findings suggest the necessity of positive matrix factorization (PMF)-based approaches for evaluating health effects of PM_2.5 while considering the spatial heterogeneity in the compositions and source contributions of PM_2.5.

     

Characterization of Major Chemical Components of Fine Particulate Matter in North Carolina

Abstract

This paper presents measurements of daily sampling of fine particulate matter (PM_2.5) and its major chemical components at three urban and one rural locations in North Carolina during 2002. At both urban and rural sites, the major insoluble component of PM_2.5 is organic matter, and the major soluble components are sulfate (SO₄ ^2?), ammonium (NH₄ ⁺), and nitrate (NO₃ ^?). NH₄ ⁺ is neutralized mainly by SO₄ ^2? rather than by NO₃ ^?, except in winter when SO₄ ^2? concentration is relatively low, whereas NO₃ ^? concentration is high. The equivalent ratio of NH₄ ⁺ to the sum of SO₄ ^2? and NO₃ ^? is <1, suggesting that SO₄ ^2?and NO₃ ^?are not completely neutralized by NH₄ ⁺. At both rural and urban sites, SO₄ ^2?concentration displays a maximum in summer and a minimum in winter, whereas NO₃ ^?displays an opposite seasonal trend. Mass ratio of NO₃ ^? to SO₄ ^2?is consistently <1 at all sites, suggesting that stationary source emissions may play an important role in PM_2.5 formation in those areas. Organic carbon and elemental carbon are well correlated at three urban sites although they are poorly correlated at the agriculture site. Other than the daily samples, hourly samples were measured at one urban site. PM_2.5 mass concen trations display a peak in early morning, and a second peak in late afternoon. Back trajectory analysis shows that air masses with lower PM_2.5 mass content mainly originate from the marine environment or from a continental environment but with a strong subsidence from the upper troposphere. Air masses with high PM_2.5 mass concentrations are largely from continental sources. Our study of fine particulate matter and its chemical composition in North Carolina provides crucial information that may be used to determine the efficacy of the new National Ambient Air Quality Standard (NAAQS) for PM fine. Moreover, the gas-to-particle conversion processes provide improved prediction of long-range transport of pollutants and air quality.     

Spatial patterns of mobile source particulate matter emissions-to-exposure relationships across the United States

Assessing the public health benefits from air pollution control measures is assisted by understanding the relationship between mobile source emissions and subsequent fine particulate matter (PM_2.5) exposure. Since this relationship varies by location, we characterized its magnitude and geographic distribution using the intake fraction (iF) concept. We considered emissions of primary PM_2.5 as well as particle precursors SO₂ and NO_x from each of 3080 counties in the US. We modeled the relationship between these emissions and total US population exposure to PM_2.5, making use of a source–receptor matrix developed for health risk assessment. For primary PM_2.5, we found a median iF of 1.2 per million, with a range of 0.12–25. Half of the total exposure was reached by a median distance of 150 km from the county where mobile source emissions originated, though this spatial extent varied across counties from within the county borders to 1800 km away. For secondary ammonium sulfate from SO₂ emissions, the median iF was 0.41 per million (range: 0.050–10), versus 0.068 per million for secondary ammonium nitrate from NO_x emissions (range: 0.00092–1.3). The median distance to half of the total exposure was greater for secondary PM_2.5 (450 km for sulfate, 390 km for nitrate). Regression analyses using exhaustive population predictors explained much of the variation in primary PM_2.5 iF (R²=0.83) as well as secondary sulfate and nitrate iF (R²=0.74 and 0.60), with greater near-source contribution for primary than for secondary PM_2.5. We conclude that long-range dispersion models with coarse geographic resolution are appropriate for risk assessments of secondary PM_2.5 or primary PM_2.5 emitted from mobile sources in rural areas, but that more resolved dispersion models are warranted for primary PM_2.5 in urban areas due to the substantial contribution of near-source populations.     

Fine particulate speciation profile and emission factor of municipal solid waste incinerator established by dilution sampling method

In this study, fine particulate matter (PM_2.5) emitted from a municipal solid waste incinerator (MSWI) was collected using dilution sampling method. Chemical compositions of the collected PM_2.5 samples, including carbon content, metal elements, and water-soluble ions, were analyzed. Traditional in-stack hot sampling was simultaneously conducted to compare the influences of dilution on PM_2.5 emissions and the characteristics of the bonded chemical species. The results, established by a dilution sampling method, show that PM_2.5 and total particulate matter (TPM) emission factors were 61.6 ± 4.52 and 66.1 ± 5.27 g ton-waste^?1, respectively. The average ratio of PM_2.5/TPM is 0.93, indicating that more than 90% of PM emission from the MSWI was fine particulate. The major chemical species in PM_2.5 included organic carbon (OC), Cl^?, NH₄⁺, elemental carbon (EC) and Si, which account for 69.7% of PM_2.5 mass. OC was from the unburned carbon in the exhaust, which adsorbed onto the particulate during the cooling process. High Cl^? emission is primarily attributable to wastes containing plastic bags made of polyvinyl chloride, salt in kitchen refuse and waste biomass, and so on. Minor species that account for 0.01–1% of PM_2.5 mass included SO₄^2-, K⁺, Na, K, NO₃^?, Al, Ca²⁺, Zn, Ca, Cu, Fe, Pb, and Mg. The mean ratio of dilution method/in-stack hot method was 0.454. The contents of water-soluble ions (Cl^?, SO₄^2-, NO₃^?) were significantly enriched in PM_2.5 via gas-to-particle conversion in the dilution process. Results indicate that in-stack hot sampling would underestimate levels of these species in PM_2.5.

Implications: PM_2.5 samples from a municipal solid waste incinerator (MSWI) were collected simultaneously by a dilution sampling technique and a traditional in-stack method. PM_2.5 emission factors and chemical speciation profiles were established. Dilution sampling provides more reliable data than in-stack hot sampling. The results can be applied to estimate the PM_2.5 emission inventories of MSWI, and the source profile can be used for contribution estimate of chemical mass balance modeling.     

Chemical characterization of particles in winter-night smog in Tokyo

Continuous measurement of PM₁₀, PM_2.5 and carbon (organic, elemental composition) concentrations, and samples of PM₁₀ and PM_2.5 collected on a polycarbonate membrane filter (Nuclepore^®, pore size: 0.8 μm), were carried out during a period from December 1998 to January 1999 at Shinjuku in Tokyo in order to investigate the chemical characterization of particles in winter-night smog within a large area of the Japan Kanto Plain including the Tokyo Metropolitan area. These were measured using an ambient particulate monitor (tapered element oscillating microbalance—TEOM) and a carbon particulate monitor. Elemental compositions in the filter samples of PM₁₀ and PM_2.5 were determined by means of particle-induced X-ray emission (PIXE) analysis. Ionic species (anion: F⁻, Cl⁻, NO₃⁻, SO₄²⁻ and C₂O₄²⁻; cation: Na⁺, NH₄⁺, K⁺, Ca²⁺ and Mg²⁺) in the filter samples were analyzed by ion chromatography. The temporal variation patterns of PM_2.5 were similar to those of PM₁₀ and carbon. PM_2.5 made up 90% of the PM₁₀ at a high concentration, and 70% at a low concentration. Concentrations of 22 elements in both the PM₁₀ and PM_2.5 samples were consistently determined by PIXE, and Na, Mg, Al, Si, S, Cl, K, Ca, Fe, Zn and Pb were found to be the major components. Among these S and Cl were the most dominant elements of the PM_2.5 and PM₁₀ at high concentrations. Ionic species were mainly composed of Cl⁻, NO₃⁻, SO₄²⁻ and NH₄⁺. The component proportion of carbon, the other elements (total amount of measured elements other than S and Cl) and secondary-formed particles of PM_2.5 was similar to that of PM₁₀. The major component was carbon particles at a low concentration and secondary-formed particles at a high concentration. The proportion of NH₄NO₃ and NH₄Cl plus HCl in secondary-formed particles at a high concentration, in particular, was as high as 90%.     

Spatial and seasonal variations of elemental and ion components in air particulate matters in three mega-cities in China

Beijing–Tianjin–Hebei region is one of the most important political, economic and cultural centers of China. The rapid development of economy in last decades has caused severe air pollution problems, which has resulted in considerable harm to local ecological environment and human health. In this study, total 671 air samples were collected from Beijing, Tianjin and Shijiazhuang (the capital city in Hebei province), one reference site and four background sites in four seasons. Particulate matters (PMs) with different sizes, elements and dissolvable ions in PMs were analyzed. Pollutant concentrations, characteristics and seasonal variations were discussed in order to describe the pollution status and the possible sources in this region. Enriched factors of K, Ca, Cr, Fe, Cu, Zn, As, Cd and Pb were all higher than 10. Concentrations of dissolvable ions were in the order of NO₃^–, SO₄^2–>NH₄⁺>Cl^–>Ca²⁺, K⁺, Na⁺>Mg²⁺, F^–. NO₃^–, SO₄^2–, NH₄⁺, Cl^– were the most important ion pollutants in the three cities which accounted for 90.3–92.3% of total 9 ion concentrations. Ion concentrations in the PMs were in the order of PM₁>PM_1–2.5>PM_2.5–10>PM₁₀>TSP. More than 50% of the dissolvable ions exist in PM1 and the percentage increases to 73.9–94.8% in PM_2.5. Human activities should be the main sources of the metallic pollutants, among which coal combustion was identified as the primary one.     

Identification of sources of pollutants in precipitation measured at the mid-Atlantic US coast using potential source contribution function (PSCF)

Potential source contribution function (PSCF) was employed to study the source receptor relationships for 14 chemical species (Mn, SO₄²⁻, Zn, Al, Fe, Cu, Cr, Ni, Cd, NO₃, NH₄⁺, K⁺, Mg²⁺,and Pb) found in precipitation collected at Lewes, Delaware. This study identified areas of the Eastern United States as possible emission source areas that could have contributed to the 14 element concentrations observed at Lewes. The identified regions in the Eastern United States generally coincide well with known emission source areas. The likely emission sources for these chemical species include oil- and coal-fired power plants, incinerators, motor vehicles, and iron and steel mills.     

Source Apportionment of Fine Particulate Matter in the Southeastern United States

Abstract

Particulate matter (PM) less than 2.5 μm in size (PM_2.5)source apportionment by chemical mass balance receptor modeling was performed to enhance regional characterization of source impacts in the southeastern United States. Secondary particles, such as NH₄HSO₄, (NH₄)₂SO₄,NH₄NO₃, and secondary organic carbon (OC) (SOC), formed by atmospheric photochemical reactions, contribute the majority (<50%) of ambient PM_2.5 with strong seasonality. Source apportionment results indicate that motor vehicle and biomass burning are the two main primary sources in the southeast, showing relatively more motor vehicle source impacts rather than biomass burning source impacts in populated urban areas and vice versa in less urbanized areas. Spatial distributions of primary source impacts show that each primary source has distinctively different spatial source impacts. Results also find impacts from shipping activities along the coast. Spatiotemporal correlations indicate that secondary particles are more regionally distributed, as are biomass burning and dust, whereas impacts of other primary sources are more local.     

Determination of sources of fine particles in different ambient atmospheres in South Korea using a chemical mass balance model

Abstract

To determine the sources of particulate matter less than 2.5?μm (PM_2.5 in different ambient atmospheres (urban, roadside, industrial, and rural sites), the chemical components of PM_2.5 such as ions (Cl^-, NO₃^-, SO₄^2-, NH₄⁺, Na⁺, K⁺, Ca²⁺, and Mg²⁺), carbonaceous species, and elements (Al, As, Ba, Cd, Cu, Fe, Mn, Ni, Pb, Se, V, and Zn) were measured. The average mass concentrations of PM_2.5 at the urban, roadside, industrial, and rural sites were 31.5?±?14.8, 31.6?±?22.3, 31.4?±?16.0, and 25.8?±?12.4?μg/m³, respectively. Except for secondary ammonium sulfate and ammonium nitrate, the model results showed that the traffic source (i.e., the sum of gasoline and diesel vehicle sources) was the most dominant source of PM_2.5 (17.1%) followed by biomass burning (13.8%) at the urban site. The major primary sources of PM_2.5 were consistent with the site characteristics (diesel vehicle source at the roadside site, coal-fired plants at the industrial site, and biomass burning at the rural site). Seasonal data from the urban site suggested that ammonium sulfate and ammonium nitrate were the most dominant sources of PM_2.5 during all seasons. Further, the contribution of road dust source to PM_2.5 increased during spring and fall seasons. We conclude that the determination of the major PM_2.5 sources is useful for establishing efficient control strategies for PM_2.5 in different regions and seasons.     

A highly resolved temporal and spatial air pollutant emission inventory for the Pearl River Delta region, China and its uncertainty assessment

A highly resolved temporal and spatial Pearl River Delta (PRD) regional emission inventory for the year 2006 was developed with the use of best available domestic emission factors and activity data. The inventory covers major emission sources in the region and a bottom–up approach was adopted to compile the inventory for those sources where possible. The results show that the estimates for SO₂, NO_x, CO, PM₁₀, PM_2.5 and VOC emissions in the PRD region for the year 2006 are 711.4 kt, 891.9 kt, 3840.6 kt, 418.4 kt, 204.6 kt, and 1180.1 kt, respectively. About 91.4% of SO₂ emissions were from power plant and industrial sources, and 87.2% of NO_x emissions were from power plant and mobile sources. The industrial, mobile and power plant sources are major contributors to PM₁₀ and PM_2.5 emissions, accounting for 97.7% of the total PM₁₀ and 97.2% of PM_2.5 emissions, respectively. Mobile, biogenic and VOC product-related sources are responsible for 90.5% of the total VOC emissions. The emissions are spatially allocated onto grid cells with a resolution of 3 km × 3 km, showing that anthropogenic air pollutant emissions are mainly distributed over PRD central-southern city cluster areas. The preliminary temporal profiles were established for the power plant, industrial and on-road mobile sources. There is relatively low uncertainty in SO₂ emission estimates with a range of −16% to +21% from power plant sources, medium to high uncertainty for the NO_x emissions, and high uncertainties in the VOC, PM_2.5, PM₁₀ and CO emissions.     

Major air pollutants in Bursa,Turkey: their levels,temporal changes,interactions, and sources

Bursa is one of the largest cities of Turkey and it hosts 17 organized industrial zones. Parallel to the increase in population, rapidly growing energy consumption, and increased numbers of transport vehicles have impacts on the air quality of the city. In this study, regularly calibrated automatic samplers were employed to get the levels of air pollution in Bursa. The concentrations of CH₄ and N-CH₄ as well as the major air pollutants including PM₁₀, PM_2.5, NO, NO₂, NO_x, SO₂, CO, and O₃, were determined for 2016 and 2017 calendar years. Their levels were 1641.62?±?718.25, 33.11?±?5.45, 42.10?±?10.09, 26.41?±?9.01, 19.47?±?16.51, 46.73?±?16.56, 66.23?±?32.265, 7.60?±?3.43, 659.397?±?192.73, and 51.92?±?25.63 µg/m³ for 2016, respectively. Except for O₃, seasonal concentrations were higher in winter and autumn for both years. O₃, CO, and SO₂ had never exceeded the limit values specified in the regulations yet PM₁₀, PM_2.5, and NO₂ had violated the limits in some days. The ratios of CO/NO_x, SO₂/NO_x, and PM_2.5/PM₁₀ were examined to characterize the emission sources. Generally, domestic and industrial emissions were dominated in the fall and winter seasons, yet traffic emissions were effective in spring and summer seasons. As a result of the correlation process between O_x and NO_x, it was concluded that the most important source of O_x concentrations in winter was NO_x and O₃ was in summer.