超滤与电渗析联用降低油田采出水矿化度中试试验研究

以大庆油田常规处理后的油田采出水为处理对象，建立日产水300t的超滤预处理和电渗析脱盐处理中试试验装置。考察该工艺所能达到的技术经济指标，掌握放大规律，为万吨级工业装置和系统的设计提供基础数据。经过3000h长时间连续试运行，系统出水水质稳定，出水浊度低于1．0NTU，悬浮物和含油量低于1．00mg／L，矿化度低于1000mg／L，水质完全满足配制聚合物用水要求，证明采用处理后的油田采出水代替清水作为聚合物驱用水是可行的。     

炼油厂轻污染水回用试验研究

针对某炼油厂轻污染废水水质情况,选用了BAF(生物曝气滤池)工艺+SF(砂滤)工艺对该废水进行净化处理。通过试验研究,得到了BAF工艺合适的运行参数,取得了满意的试验结果。经BAF工艺处理后,出水COD和油平均浓度分别为9.78mg/L和0.24mg/L,再经SF工艺进一步去除SS后,出水SS平均浓度为3.8mg/L,系统处理出水完全达到工业回用水水质要求。试验证明:BAF工艺是一种高效的处理方法,适合炼油厂轻污染水的净化处理。     

超滤膜处理油田采出水用于回注的试验研究

试验采用截留分子量为100 ku的PVDF(聚偏氟乙烯)超滤膜组件对大庆油田采出水进行了处理,处理水用于油田回注以减少清水的消耗和降低环境污染,同时确定了最佳操作条件和膜清洗方法并考察了超滤出水水质的影响.结果表明最佳的操作条件为:跨膜压差0.30～0.35 MPa,膜面流速3.0～3.5 m/s,温度35～40 ℃.超滤出水中的悬浮物、含油量均低于1.00 mg/L,粒径中值和SRB不能检出,超滤出水水质完全满足油田回注水标准.     

三元复合驱采出水乳化稳定性及破乳的研究

由于三元复合驱原油中新型驱油用化学品的应用以及原油劣质化使得采出水乳化严重.而且三元复合驱采出水经油水分离后含油量升高.基于此.通过对不同类型的破乳剂的分析及其工艺条件的考察,探讨了影响三元复合驱采出水破乳的因素,其中破乳剂FB94具有较好的破乳效果.采用模拟三元复合驱采出水(碱为1 200 mg/L、聚合物为200 mg/L、表面活性剂为400mg/L),投加破乳剂FB94为160 mg/L,控制沉降时问为120 min、温度为45℃,当初始含油量为5 000 mg/L时.破乳后水中含油量降至195 mg/L,脱油率为96.1%,当初始含油量为1 500 mg/L时,破乳后水中含油量降至87 mg/L.脱油率为94.2%.     

MBR和BAF用于以家庭回用为目的的灰水净化研究

以灰水净化后回用于家庭冲厕为目的,小试研究了采用平板膜生物反应器(MBR)和"火山岩滤料曝气生物滤池(BAF)+平板膜过滤"对灰水再生处理的差异性和适宜的工艺条件。研究表明,MBR和BAF在不同的季节净化灰水后均可作为优质的家庭冲厕用水。冬春季条件下,MBR即使HRT为2.5~3 h、MLSS为3 500~4 500 mg/L,出水浊度、NH3-N、BOD5和CODs分别低于0.3 NTU、4.0 mg/L、3 mg/L、40 mg/L;夏季CODs一般不超过20 mg/L。BAF冬春季填料接触反应时间2.95~5.89 h,反冲洗周期为36~48 h条件下,出水的浊度为0.6~4 NTU,NH3-N、BOD5均小于4 mg/L,CODs为10~50mg/L;夏秋季接触反应时间2.36~2.95 h,反冲洗周期为24 h,出水的NH3-N小于0.5 mg/L,CODS保持10~35 mg/L。BAF出水经过平板膜直接过滤,出水达到和接近MBR出水的水质。BAF与膜过滤结合净化灰水能够实现良好的再生水水质。     

MBR-纳滤组合工艺在生活污水和大型超市废水处理中的研究

以膜-生物反应器(MBR)为预处理工艺,构建了MBR-纳滤组合系统并应用于生活污水和大型超市废水的处理,考察MBR作为纳滤预处理的可行性,评价纳滤膜的出水水质,分析不同操作模式和不同进水水质对纳滤膜的渗透性能的影响。研究表明,MBR作为纳滤的预处理是完全可行的。MBR-纳滤组合工艺处理生活污水的出水平均值:浊度0.09～0.44 NTU,电导率553.7～902.3μS/cm,TOC 1.75～5.57 mg/L,TN 1 1.3～12.5 mg/L,TP0.2 mg/L;MBR-纳滤组合工艺处理超市废水的出水平均值:浊度0.075～0.26 NTU,电导率143.2～388.9μS/cm,TOC 2.71～5.03 mg/L,TN为1.6～3.3 mg/L,TP0.2 mg/L。纳滤系统的出水水质低于城市生活饮用水标准中绝大多数常规检测项目中所规定的限值,也可满足循环冷却水用再生水水质标准。     

印染废水出水回用与实践

采用过滤-碳纤维吸附工艺对印染废水一级出水进行深度处理,废水COD可由80 mg/L降至30～40mg/L,出水水质完全满足生产工艺回用水要求.该技术具有工艺简单、投资少、运行费用低、操作简单等优点,特别适用于水资源短缺的中小印染企业.     

炼油厂轻污染水回用试验研究

针对某炼油厂轻污染废水水质情况，选用了BAF（生物曝气滤池）工艺＋SF（砂滤）工艺对该废水进行净化处理。通过试验研究，得到了BAF工艺合适的运行参数，取得了满意的试验结果。经BAF工艺处理后，出水COD和油平均浓度分别为9.78mg／L和0.24mg／L，再经SF工艺进一步去除SS后，出水SS平均浓度为3．8mg／L，系统处理出水完全达到工业回用水水质要求。试验证明：BAF工艺是一种高效的处理方法，适合炼油厂轻污染水的净化处理。     

一体式膜生物反应器处理生活污水的中试研究

采用中试规模(1.8 m3/d)的缺氧-好氧膜生物反应器(A/O MBR)对城市污水处理回用进行了试验研究.试验结果表明,该工艺处理效果优良,系统对COD、氨氮、浊度、总氮、总磷去除率较高,COD、氨氮出水浓度分别为7～39 mg/L、0～1.31 mg/L.出水水质优于城市杂用水水质标准(GB/T18920-2002).     

改性无纺布膜生物反应器处理聚酯工艺废水研究

采用自制壳聚糖改性聚丙烯无纺布膜为膜组件的A/O-MBR(厌氧/好氧-膜生物反应器)工艺对聚酯工艺废水的处理进行了研究,并与PVDF商品膜性能进行了比较研究。在近70 d的运行中,当进水COD在200~500 mg/L之间,总氮在30~45 mg/L之间波动时,2种平板膜出水水质稳定。出水COD40 mg/L,NH4+-N0.5 mg/L,TN5 mg/L,浊度0.2 NTU,均满足回用水水质要求和最新的辽宁省废水排放标准。实验中考察分析了污泥浓度和COD/TN对总氮去除率的影响。对比2种膜的运行结果,改性聚丙烯无纺布膜的出水水质略好于PVDF商品膜,但过膜压力稍大、膜通量稍小。     

UF-RO-NF应用于电镀镍漂洗废水回用中试研究

采用“UF-RO-NF”中试装置处理电镀镍漂洗废水,在周期运行的工况下,考察其浓淡水回用效果以及膜通量变化情况。研究表明,该套系统淡水COD、Ni离子、电导率的平均值为70.6 mg/L、2.93 mg/L、91.1μs/cm^2,远低于该生产车间镀镍漂洗水,可以回用。浓水COD、Ni离子、电导率相对于漂洗水均有4倍以上的浓缩效果,具有一定的回用价值。整个系统在试验运行10个周期内膜通量保持不变。     

亚硝酸盐氮测定中的稳定性试验

对亚硝酸盐氮测定的清洁水样及1．00mg／L亚硝酸盐氮标准使用溶液分别进行了稳定性试验，试验表明，清洁水样置冰箱内至少可保存30d；1．00mg／L亚硝酸盐氮标准溶液可保存180d，大大延长了国标方法中规定的24h的保存期，既提高了工作效率，又节约了试剂，在实际工作中具有一定的可行性及推广性。     

Laboratory and field evaluation of a pretreatment system for removing organics from produced water

Co-produced water from the oil and gas industry accounts for a significant waste stream in the United States. This "produced water" is characterized by saline water containing a variety of pollutants, including water soluble and immiscible organics and many inorganic species. To reuse produced water, removal of both the inorganic dissolved solids and organic compounds is necessary. In this research, the effectiveness of a pretreatment system consisting of surfactant modified zeolite (SMZ) adsorption followed by a membrane bioreactor (MBR) was evaluated for simultaneous removal of carboxylates and hazardous substances, such as benzene, toluene, ethylbenzene, and xylenes (BTEX) from saline-produced water. A laboratory-scale MBR, operated at a 9.6-hour hydraulic residence time, degraded 92% of the carboxylates present in synthetic produced water. When BTEX was introduced simultaneously to the MBR system with the carboxylates, the system achieved 80 to 95% removal of BTEX via biodegradation. These results suggest that simultaneous biodegradation of both BTEX and carboxylate constituents found in produced water is possible. A field test conducted at a produced water disposal facility in Farmington, New Mexico confirmed the laboratory-scale results for the MBR and demonstrated enhanced removal of BTEX using a treatment train consisting of SMZ columns followed by the MBR. While most of the BTEX constituents of the produced water adsorbed onto the SMZ adsorption system, approximately 95% of the BTEX that penetrated the SMZ and entered the MBR was biodegraded in the MBR. Removal rates of acetate (influent concentrations of 120 to 170 mg/L) ranged from 91 to 100%, and total organic carbon (influent concentrations as high as 580 mg/L) ranged from 74 to 92%, respectively. Organic removal in the MBR was accomplished at a low biomass concentration of 1 g/L throughout the field trial. While the transmembrane pressure during the laboratory-scale tests was well-controlled, it rose substantially during the field test, where no pH control was implemented. The results suggest that pretreatment with an SMZ/MBR system can provide substantial removal of organic compounds present in produced water, a necessary first step for many water-reuse applications.     

强化活性炭吸附技术深度处理焦化废水的可行性研究

采用混凝沉淀、活性炭吸附以及混凝沉淀 活性炭吸附工艺对焦化厂生化出水进行深度处理.单独混凝沉淀或活性炭吸附均可以将水样中COD降到100 mg/L以下,达到国家污水一级排放标准和冷却用水建议标准.活性炭根据不同的材质和进水而表现出不同的吸附性能,对于焦化厂生化出水,煤质炭Ⅰ和果壳炭均表现出良好的吸附效果,并使出水COD＜100 mg/L,但处理成本较高.混凝沉淀 活性炭吸附工艺充分发挥适合去除大分子污染物的混凝沉淀与适宜去除小分子污染物的活性炭吸附技术两者的协同增效作用,吸附单元采用廉价的煤质炭,使出水水质达到个别生产或生活用水回用标准,并且降低深度处理成本.研究结果表明,混凝沉淀 活性炭吸附作为焦化厂生化出水回用工艺是经济可行的.     

臭氧-BAF组合工艺对石化行业废水深度处理的中试研究

采用臭氧-曝气生物滤池（BAF）组合工艺对中石化九江分公司二级生化出水进行深度处理中试实验。探讨了臭氧投加量、进水水质冲击负荷等因素对该组合工艺出水COD、NH₄⁺-N的影响。中试结果表明，在该水质条件下，臭氧最佳投加量为20~25 mg/L；组合工艺处理后出水COD低于40 mg/L，NH₄⁺-N低于5 mg/L，达到中水回用设计标准；该组合工艺能够经受一定冲击负荷。     

清浊分流条件下的混凝-臭氧处理棉针织印染清废水

根据污染源头控制和废水回用的要求,对典型棉针织染整厂的不同生产过程废水排水水质特征进行了统计分析,提出了较实用的废水源头清浊分流方案。在此基础上重点研究了混凝-臭氧组合工艺对清废水处理效果,确定了最优的工艺条件。结果表明,清废水主要为洗水,占废水总量的25%～30%;混凝-臭氧组合工艺的最优工艺条件为：pH为6～9,PAC投加量为48 mg/L,PAM投加量为1.0 mg/L,臭氧接触时间为12 min（臭氧浓度为14.5 mg/L）,这时,清废水COD、色度去除率分别为71%和98%,实践证明,出水水质完全能够满足染整生产。     

Using polymer solutions to enhance recovery of mobile coal tar and creosote DNAPLs

Direct pumping and enhanced recovery of coal tar and creosote dense, non-aqueous phase liquids (DNAPLs) from the subsurface have had mixed results because these DNAPLs are viscous fluids that can potentially alter aquifer wettability. To improve the inefficiencies associated with waterflooding, the research presented here considered the use of a polymer solution that can be added to the injected flood solution to increase the viscosity and decrease the velocity of the flooding solution. Results from one-dimensional, vertically oriented laboratory column experiments that evaluate the recovery of coal-derived DNAPL with both water and polymer flooding solutions are presented. The final DNAPL saturation remaining in the column was assessed in water and oil-wet systems for three viscous DNAPLs. Adding polymer to increase the aqueous solution viscosity did not have a significant impact in water-wet systems. A final DNAPL saturation of approximately 19% was achieved for both water and polymer floods. In contrast, the addition of polymer significantly improved recovery in oil-wet systems. The final saturation was over 40% in oil-wet systems after waterflooding, but approximately 19% with a polymer flushing solution. Although the final saturation produced with polymer flooding was similar between the oil- and water-wet systems, differences in the relative permeability and distribution of DNAPL in the porous matrix caused the DNAPL recovery to be much slower in the oil-wet system.     

不同植物的表面流人工湿地系统对污染物的去除效果

通过对4种不同植物的表面流人工湿地系统处理新沂河河水的中试研究表明,在CODMn和NH 4-N进水浓度相同条件下,香蒲湿地系统出水CODMn平均浓度最低,仅为13.44 mg/L;美人蕉湿地系统出水NH 4-N平均浓度最低,仅为1.75 mg/L;香蒲和美人蕉湿地系统对CODMn的平均去除率都达到40%以上,而千屈菜和水葱湿地系统都低于30%;美人蕉、香蒲和千屈菜湿地系统对NH 4-N的平均去除率都达到65%以上,而水葱系统则低于60%.综合比较,香蒲和美人蕉湿地系统的净化能力较强.4种植物中水葱耐淹能力最强,完全淹水22 d以上依然生长良好;千屈菜耐淹能力最弱,完全淹水7 d后就开始枯萎,17 d后地上、地下部分全部死亡.     

A2O-MBR 工艺处理城市污水作农业灌溉用水中试研究简

为开发一种污水再生利用于农田灌溉领域的新型技术，本实验以城市污水为研究对象，采用A²O-MBR工艺进行中试研究，并将系统出水水质与《农田灌溉水质标准（GB5084-2005）》的主要水质指标进行对比分析。结果表明，系统COD和BOD₅出水浓度范围分别为3.2~59.6 mg/L、1.0~7.6 mg/L，系统出水pH为7.16~7.54，悬浮物浓度几乎为0，上述指标均符合标准；TP、TN和氨氮的出水范围分别为0.03~0.79 mg/L、1.6~17.7 mg/L和0.8~10.3 mg/L。《农田灌溉水质标准》没有对上述3个指标提出具体要求，且少量的氮磷是植物生长的营养元素。该系统出水的主要水质指标符合标准要求。     

Duo-molecularly imprinted polymer-coated magnetic particles for class-selective removal of endocrine-disrupting compounds from aqueous environment

The removal of steroid and phenolic endocrine-disrupting compounds (EDCs) from an aqueous environment was investigated using magnetic particles encapsulated by a duo-molecularly imprinted polymer (duo-MIP). The effect of environmental variables on the binding efficiency was studied. Experimental results showed that the amount of EDCs adsorbed was neither affected by up to 10.0 mM NaCl nor significantly interfered by up to 10.0 mg/L humic acid. Negligible influence was observed from pH 3.3 to pH 6.8, but a decrease started at pH 9. Freundlich isotherm parameters indicated binding capacities in the order of DES?>?E2?～?E1?>?BPA. The applicability of class-selective removal was verified using river water samples spiked with these EDCs at 10 μg/L; the binding efficiencies were 90, 90, 88, and 98 % for estrone (E1), 17β-estradiol (E2), bisphenol A (BPA), and diethylstilbestrol (DES), respectively. A reuse investigation verified constant binding capacities exhibiting <2 % reduction after seven cycles of regeneration.