利用厌氧菌可溶性代谢物处理含镉废水的条件研究

本文研究了微生物代谢物的投加量、pH、温度和反应时间等不同的条件下对废水中镉的去除效果,最终通过正交实验确定了微生物代谢物对含镉废水处理的最佳反应条件为:微生物代谢物投加量为1.10g、反应时间为20分钟、pH=6、温度20℃,此时镉的去除率为95.3%.并用实际含镉、铜和镍等离子的电镀废水进行验证实验,同样发现微生物代谢物对Cu<'2 和Ni<'2 两个离子具有很好的去除效果,三者去除率分别达到97.7%、95%和91.5%.     

改性膨润土处理油田废水实验研究

通过高温焙烧和交联改性两种方法制备出改性膨润土,研究其在不同条件下对油田废水CODCr的去除效果。结果表明:改性膨润土对油田废水CODCr的去除效率有显著提高,最高可达65.32%。为膨润土的改性及其在油田废水处理中的应用提供了参考依据。     

改性凹凸棒土复配PAC去除水源水中突发性重金属铜污染研究

以聚合氯化铝为絮凝剂采用强化混凝的处理方法,对水源水中突发性重金属铜的去除进行研究,考察混凝剂投加量和投加改性凹凸棒土等对Cu2+去除率的影响。结果表明,常规工艺对铜的最大去除率为67%,加入改性凹凸棒土可显著提高混凝效果,组合工艺去除铜的最优条件是,聚合氯化铝投加量为30mg/L,改性凹凸棒土投加量为30mg/L,在混凝前1min投加,此时铜的去除率达85%以上。     

电镀污染区土壤淋洗修复研究

通过实验室模拟实验,采用振荡淋洗方法,研究草酸、柠檬酸、盐酸、氯化钙和EDTA溶液对某电镀厂附近土壤中重金属的去除效果。探讨了淋洗剂浓度、淋洗时间和土液比对淋洗效果的影响,重点研究了柠檬酸淋洗前后土壤中重金属形态的变化。结果表明,0.8mol/L的柠檬酸在土水比为1:10,淋洗5h的条件下可以达到最佳淋洗效果,Cu、Ni、Pb、Cr、Cd和Mn的去除率分别是41.81%、33%、19.96%、28.32%、41.4%和58.48%。     

沸石人工湿地填料对氨氮的去除效果

选取沸石作为人工湿地填料,对沸石吸附实验的水力负荷、污染负荷、运行方式分别进行研究,探讨沸石对氨氮的去除效果及影响因素。结果表明,沸石对氨氮有较好的处理效果,相同条件下远优于砂石。水力负荷会影响沸石对氨氮的去除效果,低水力负荷下的处理效果和稳定性均较好。沸石在不同氨氮浓度下的去除效果差别不大。运行方式对氨氮的去除有一定影响,6 h间歇周期运行时,沸石填料对氨氮的去除效果好于其他间歇周期。     

臭氧高级氧化法处理染料废水的研究

采用臭氧高级氧化技术对某染料废水进行处理,探究不同条件对染料废水COD以及色度的去除效果的影响,确定最佳工艺条件。在最佳条件下,采用单独臭氧、单独紫外、臭氧-紫外、臭氧-双氧水以及臭氧-铁炭五种氧化方法对染料废水进行处理。结果表明:臭氧氧化技术最佳条件为pH值=8,臭氧流量80 L/h,反应时间为2 h;采用最佳处理方案,采用臭氧-紫外高级氧化技术处理染料废水,其脱色率为98.3%,COD去除率为67.0%。     

利用高效复合菌净化城市微污染水的静态试验研究

EM经三种培养基富集培养后，用其培养液对微污染水进行净化处理。结果表明：三种培养液在曝气或静置的运行条件下，对微污染水中的COD和氨氮有稳定良好的去除效果，其去除率分别为50％和85％；对磷酸盐的去除随运行条件的不同而不同，曝气条件下比静置条件要好，其去除率也都在60％以上。试验证明：EM培养液对微污染水有良好的净化能力。     

活性炭负载纳米零价铁去除水中高氯酸盐研究

如何有效去除水中高氯酸盐,解决普通零价铁去除效果不佳和易被氧化等缺点是本研究的主要出发点。采用浸润法制备活性炭负载纳米零价铁复合材料,运用扫描电镜对复合材料进行表征,考察了不同条件下复合材料对高氯酸盐的去除效果,并分析了去除机理。研究结果表明:高氯酸盐去除效果在一定范围内随着材料含铁量的增加而升高;高氯酸盐去除效果与其初始浓度呈负相关;pH=5时,去除效果最好;共存阴离子对去除效果具有一定抑制作用;溶液中高氯酸根最终被复合材料(nZVI-GAC)还原成无毒Cl-。     

城镇污水处理厂NPR工艺低温运行的效能分析

介绍了天津市某城镇污水处理厂NPR工艺的特点及运行状况。通过对污水厂的运行监测数据分析,研究了该工艺在低温条件下处理城镇生活污水时的脱氮除磷效果。结果表明:NPR工艺具有一定的优异性,它能在降低能耗的前提下使系统COD和SS的去除率进一步降低,出水能达到中水回用标准,有利于污水的再生利用;低温影响NPR系统的硝化及反硝化率,低温下有机物的去除更易受到有机负荷的影响;温度对生物去除SS,COD和TP的效果影响不大,对NH3-N及TN的去除效果影响比较明显。低温下污水处理厂COD、SS、NH3-N、TN、TP的平均去除率分别为72.1%、94.9%、67.5%、55.1%、66.5%。     

多层生物滴滤池去除污染物规律研究

实验采用以火山岩为填料的多层生物滴滤池装置处理模拟的生活污水,研究了在水力负荷为1.5 m~3/(m~2·d)的条件下滴滤池各层对污染物的去除规律。实验结果表明:滴滤池对CODcr、NH_4~+-N、TN和TP的平均去除率分别为94.1%、97.4%、53.4%和41.7%。滴滤池上层和中层对CODcr的去除贡献较大,CODcr去除量占整体去除量的85.2%。滴滤池对NH_4~+-N的去除率从上至下依次降低,各层对NH_4~+-N的平均去除率分别为44.9%、33.9%和19.0%。TN、TP的分层去除规律相似,中层的去除贡献较大,上层和下层的去除量较少。     

Modeling of the denitrification/anaerobic digestion process of salmon fishery wastewater in a biofilm tubular reactor

The literature has paid scarce attention to the modeling of the denitrification-anaerobic digestion process in packed bed biofilm tubular reactors used to treat wastewater. The present study obtained a steady-state model for industrial salmon fishery wastewater treatment in a biofilm tubular reactor, including pH as a variable and the effect of biomass on hydrolysis. The axial profile of the reactor components and process efficiency were predicted with deviations below 6%. The optimal operating zone for the process was found at hydraulic retention time (HRT)>1.5d and inlet protein concentration (S(prot,0))<3000 mgTOCL(-1). Based on our results, we concluded that the removal of organic matter and nitrogen compounds depended mainly on HRT. The effluent pH was mainly affected by the C/N ratio, where a decrease increases pH. Organic matter removal was related with the anaerobic digestion process, while denitrification influenced mostly nitrate and nitrite removal.     

Effects of arsenic concentrations and forms on arsenic uptake by the hyperaccumulator ladder brake

Ladder brake (Pteris vittata L.) is a newly discovered arsenic hyperaccumulator. No information is available about arsenic effects on ladder brake. This study determined the effects of different arsenic concentrations (50 to 1000 mg kg(-1)) or forms (organic vs. inorganic and arsenite vs. arsenate) applied to soils on growth and arsenic uptake by ladder brake. Young plants were grown in a greenhouse for 12 or 18 wk. Ladder brake was highly tolerant of arsenic and survived in soil containing up to 500 mg As kg(-1). The fact that addition of arsenate up to 100 mg As kg(-1) increased fern biomass by 64 to 107%, coupled with higher arsenic concentration in younger fronds at low soil arsenic concentrations and older fronds at high soil arsenic concentrations, implies that arsenic may be beneficial for fern growth. Addition of 50 mg As kg(-1) was best for fern growth and arsenic accumulation, resulting in the highest fern biomass (3.9 g plant(-1)), bioconcentration factor (up to 63), and translocation factor (up to 25). With an exception of FeAsO4 and AlAsO4, which had the lowest effects due to their low solubility, little difference was observed among other arsenic forms mainly because of arsenic conversion in soil. Aboveground biomass was mostly responsible for accumulation of arsenic by plant (75-99%). Up to 26% of the added arsenic was removed by ladder brake, showing the high efficiency of ladder brake in arsenic removal. The results suggest that ladder brake may be a good candidate to remediate arsenic-contaminated soils.     

生物膨胀床技术处理含氨臭气研究

针对传统生物除臭方法的一些不足，本试验提出采用生物膨胀床技术处理含氨臭气。文中系统研究了不同填料、进气浓度、停留时间等因素对处理效果的影响。结果表明：采用兰石和活性炭的混合物做填料时膨胀床对氨的去除率较高；当进气浓度低于100mg／m^3时，反应器对氨气的去除率在98％以上；适宜停留时间是28.6s。对反应器溶液中各形态氮浓度的分析可知氨在反应器中的转化以硝化反应为主，主要被氧化为硝酸根。     

The effect of landfill leachate composition on organics and nitrogen removal in an activated sludge system with bentonite additive

A pre-denitrification activated sludge system (AS) without internal recycle was used in lab-scale studies of landfill leachate treatment. A bentonite supplement at a ratio of 1:4 (mineral : biomass) was used to ensure high sludge settling levels and to serve as a micro-organisms carrier. The system was operated within different parameters such as hydraulic retention time (HRT), ammonia loading rate (ALR) or external recycle ratio, which was adapted to treat varying leachate concentrations of COD and ammonia, ranging from 1020 to 2680 mgO(2)l(-1) and 400-890 mgNH(4)-Nl(-1) respectively. The nitrification was complete and ammonia oxidation reached 99%; this was obtained while the ALR did not exceed 0.09 g NH(4)(+)-Ng(-1)MLVSS d(-1) and HRT was not lower than 1 day (in the aeration reactor). The performance of denitrification was successfully improved by controlling the external recycle rate, when the BOD(5)/N ratio in the raw leachate was 4.1. Consequently, N-removal of up to 80% was achieved. A 10-fold decrease in the denitrification rate was obtained at a BOD(5)/N ratio of 0.5. The efficiency of COD removal varied significantly from 36% to 84%. The positive effect of bentonite addition was determined and is discussed based on preliminary studies. The experiments were carried out in fill-and-draw activated sludge with bentonite; the biomass ratio was 1:2. The activated sludge with bentonite was fed with a synthetic high ammonia and organic-free medium.     

Aerobic treatment of palm oil mill effluent

In this study treatment of palm oil mill effluent (POME) was investigated using aerobic oxidation based on an activated sludge process. The effects of sludge volume index, scum index and mixed liquor suspended solids during the acclimatizing phase and biomass build-up phase were investigated in order to ascertain the reactor stability. The efficiency of the activated sludge process was evaluated by treating anaerobically digested and diluted raw POME obtained from Golden Hope Plantations, Malaysia. The treatment of POME was carried out at a fixed biomass concentration of 3900+/-200mg/L, whereas the corresponding sludge volume index was found to be around 105+/-5mL/g. The initial studies on the efficiency of the activated sludge reactor were carried out using diluted raw POME for varying the hydraulic retention time, viz: 18, 24, 30 and 36h and influent COD concentration, viz: 1000, 2000, 3000, 4000 and 5000mg/L, respectively. The results showed that at the end of 36h of hydraulic retention time for the above said influent COD, the COD removal efficiencies were found to be 83%, 72%, 64%, 54% and 42% whereas at 24h hydraulic retention time they were 57%, 45%, 38%, 30% and 27%, respectively. The effectiveness of aerobic oxidation was also compared between anaerobically digested and diluted raw POME having corresponding CODs of 3908 and 3925mg/L, for varying hydraulic retention time, viz: 18, 24, 30, 36, 42, 48, 54 and 60h. The dissolved oxygen concentration and pH in the activated sludge reactor were found to be 1.8-2.2mg/L and 7-8.5, respectively. The scum index was found to rise from 0.5% to 1.9% during the acclimatizing phase and biomass build-up phase.     

AnSBBR applied to the treatment of wastewater from a personal care industry: Effect of organic load and fill time

The objective of this work was to study the technological feasibility of treating wastewater from a personal care industry (PCI-WW) in a mechanically stirred anaerobic sequencing batch biofilm reactor (AnSBBR) containing immobilized biomass on polyurethane foam. An assessment was made on how system efficiency and stability would be affected by: increasing organic load; supplementation of nutrients and alkalinity; and different feed strategies. The AnSBBR operated with 8-h cycles, stirring speed of 400 rpm, temperature of 30 °C, and treated with 2.0 L wastewater per cycle. First the efficiency and stability of the AnSBBR were studied when submitted to an organic loading rate (OLR) of 3.1–9.4 gCOD/(L d), and when the PCI-WW was supplemented with nutrients (sucrose, urea, trace metals) and alkalinity. The AnSBBR was shown to be robust and presented stability and removal efficiency exceeding 90%. At an OLR of 12.0 gCOD/(L d) efficiency became difficult to maintain due to the presence of commercial cleansers and disinfectants in the wastewater lots. In a subsequent stage the AnSBBR treated the wastewater supplemented with alkalinity, but with no nutrients at varying feed strategies and maintaining an OLR of approximately 9.0 gCOD/(L d). The first strategy consists of feeding 2.0 L of the influent batchwise [OLR of 9.4 gCOD/(L d)]. In the second 1.0 L of influent was fed-batchwise and an additional 1.0 L was fed fed-batchwise [OLR of 9.2 gCOD/(L d)], i.e., in relation to the first strategy the feed volume was maintained but supplied in different periods. In the third strategy 1.0 L of treated effluent was maintained in the reactor and 1.0 L of influent was fed fed-batchwise [OLR of 9.0 gCOD/(L d)], i.e., in relation to the first strategy the feed volume was different but the feed period was the same and the OLR was maintained by increasing the influent concentration. Comparison of the first and second strategies revealed that organic matter removal efficiency was unaffected (exceeding 90%). The third strategy resulted in a reduction in average removal efficiency from 91 to 83% when compared to the first one. A kinetic study resulted in first order kinetic parameters ranges from 0.42 to 1.46 h⁻¹ at OLRs from 3.1 to 12.0 gCOD/(L d), respectively, and the second feed strategy [OLR of 9.2 gCOD/(L d)] was shown to be the most favorable.     

Decolorization of triphenylmethane dye-bath effluent in an integrated two-stage anaerobic reactor

In the present study, decolorization of a simulated dye waste containing three different triphenylmethane (TPM) dyes--Magenta, Malachite Green and Crystal Violet, was investigated in a laboratory scale, two-stage anaerobic high-rate reactor. The effect of various parameters (influent dye concentration, hydraulic and co-substrate loading rates) on color and COD removal efficiency of the reactor has been studied. It has been shown that the influent dye concentration had little effect on overall COD and color removal efficiency. More than 99% color removal and 96% COD removal efficiency were maintained even at a dye concentration of 500 mg/l and a dye loading rate of 1000 mg/l day. However, a minimum level of glucose as supplementary carbon source is required to maintain the maximum color removal efficiency and it drops appreciably when no glucose is added to the influent. The study also showed that the acidogenic phase of the reaction plays an important role in decolorization of the TPM dyes. In addition, the two-stage anaerobic reactor was observed to have distinct advantages over the single-stage system, as the drop in color and COD removal efficiency of stage 1 are adequately compensated by stage 2 of the reactor especially under high dye loading rates accompanied by low co-substrate loading and under reduced HRTs.     

Nutrient removal in a pilot and full scale constructed wetland, Putrajaya city, Malaysia

Putrajaya Wetlands in Malaysia, a 200ha constructed wetland system consisting of 24 cells, was created in 1997-1998 to treat surface runoff caused by development and agricultural activities from an upstream catchment before entering Putrajaya Lake (400ha). It was designed for stormwater treatment, flood control and amenity use. The water quality improvement performance of a section of the wetland cells is described. The nutrient removal performance was 82.11% for total nitrogen, 70.73% for nitrate-nitrogen and 84.32% for phosphate, respectively, along six wetland cells from Upper North UN6 to UN1 from April to December 2004. Nutrient removal in pilot scale tank systems, simulating a constructed wetland and planted with examples of common species at Putrajaya, the Common Reed Phragmites karka and Tube Sedge Lepironia articulata, and the capacity of these species to retain nutrients in above and below-ground plant biomass and substrate is reported. The uptake of nutrients by the Common Reed and Tube Sedge from the pilot tank system was 42.1% TKN; 28.9% P and 17.4% TKN; 26.1% P, respectively. The nutrient uptake efficiency of the Common Reed was higher in above-ground than in below-ground tissue. The results have implications for plant species selection in the design of constructed wetlands in Malaysia and for optimizing the performance of these systems.     

碱法草浆造纸黑液厌氧生物降解研究

采用中温(34±2℃)全混合式厌氧反应器处理蒽酸和硫化烧碱草浆造纸黑液。对比厌氧发酵结合物化前或后处理两种方法进行试验,厌氧生物降解COD_(er)去除率分别为61.2～75.3％和34.9～46.2％,COD_(er)总去除率分别为80.0～87.6％和68.4～75.8％。在厌氧发酵稳态运行条件下,对发酵污泥中主要微生物类群和数量进行了研究。     

聚合硅酸硫酸铝对印染废水的预处理实验研究

本文采用硅酸钠、硫酸和硫酸铝为原料，制备出无机高分子絮凝剂聚合硅酸硫酸铝，探讨了聚合硅酸硫酸铝对广东某毛纺企业印染废水的应用性能。结果表明，聚合硅酸硫酸铝对COD和色度的去除率优于硫酸亚铁，COD和色度去除率分别可达31．8％和84％，减轻了后续生化系统的压力。