Ackee apple (Blighia sapida) seeds: a novel adsorbent for the removal of Congo Red dye from aqueous solutions

The ability of ackee apple (AA) seeds to remove Congo Red (CR) dye from aqueous solution was investigated. AA was characterised using thermo gravimetric analyser, scanning electron microscopy, Braunauer Emmett Teller, pH_pzc, elemental analysis and Boehm titration. The effects of operational parameters such as adsorbent dosage, contact time, initial dye concentration and solution pH were studied in a batch system. pH has a profound influence on the adsorption process. Maximum dye adsorption was observed at pH 3.0. The reaction was fast, reaching equilibrium in 90 min. Adsorption data were best described by Langmuir isotherm and the pseudo-second-order kinetic model with a maximum monolayer coverage of 161.89 mg·g^?1. Both boundary layer and intraparticle diffusion mechanisms were found to govern the adsorption process. Thermodynamic parameters such as standard free energy change (Δ G ⁰), standard enthalpy change (Δ H ⁰), and standard entropy change (Δ S ⁰) were studied. Values of Δ G ⁰ varied between?30.94 and?36.56 kJ·mol^?1, Δ H ⁰ was 25.61 kJ·mol^?1, and Δ S ⁰ was 74.84 kJ·mol^?1·K^?1, indicating that the removal of CR from aqueous solution by AA was spontaneous and endothermic in nature. Regeneration and reusability studies were carried out using different eluents. AA gave the highest adsorption efficiency up to four cycles when treated with 0.3 M HCl. AA was found to be an effective adsorbent for the removal of CR dye from aqueous solution.     

Ionic dye adsorption by zinc oxide nanoparticles

The adsorption behaviour of Basic Red 12, Acid Orange 7 and Acid Blue 1 on zinc oxide nanoparticles (ZNP) has been investigated to understand the physicochemical process involved and to explore the possible use of nanoparticles in the treatment and management of textile waste matter. The dye removal capacity of ZNP towards Basic Red 12, Acid Orange 7 and Acid Blue 1 was found to be 15.64, 6.78 and 6.38 mg g^?1, respectively. The adsorption process was pH dependent and optimum pH values of 9.0, 2.0 and 4.0 were obtained for Basic Red 12, Acid Orange 7 and Acid Blue 1, respectively. Equilibrium was established after 1.0 h for all dyes. Langmuir, Freundlich and Temkin isotherm models were applied to the system. The adsorbent ZNP was characterised using scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET) and Fourier transform infrared (FTIR) techniques. SEM analysis revealed the noticeable nanoporous morphology of the material. The results of FTIR spectroscopy showed that the process is driven by an electrostatic complexation mechanism. XRD studies revealed the nanocrystalline structure of ZNP. BET surface area measurement suggested a high pore volume and large surface area for the adsorbent. The kinetic measurements suggested pseudo-second-order kinetic processes with high regression coefficients and smaller standard error of estimate values and lower residual sum of squares. The thermodynamic measurements suggested that all processes were exothermic and accompanied by negative values for Δ G⁰, Δ S⁰ and Δ H⁰.     

Steam activation,characterisation and adsorption studies of activated carbon from maize tassels

In this paper, steam-produced activated carbon (STAC) from maize tassel (MT) was evaluated for its ability to remove basic dye (methylene blue MB) from aqueous solution in a batch adsorption process. The equilibrium experiments were conducted in the range of 50–300 mg/L initial MB concentrations at 30°C, for effect of pH, adsorbent dosage and contact time. The experimental data were analysed by Langmuir, Freundlich and Temkin isotherm models of adsorption. Freundlich adsorption isotherm was found to have highest value of R²(R²=0.97) compared to other models of Langmuir and Temkin having (0.96 and 0.95 respectively). STAC has a high adsorptive capacity for MB dye (200 mg/g) and also showed favourable adsorption for the dye with the separation factor (R_L<1) for the dye-activated carbon system. The kinetic data obtained were analysed using pseudo first-order kinetic equation and pseudo second-order kinetic equation. The experimental data fitted well into pseudo second-order kinetic equation, as demonstrated by the high value of R².     

Adsorptive removal of rhodamine B from textile wastewater using water chestnut (Trapa natans L.) peel: adsorption dynamics and kinetic studies

Water chestnut peel, an agricultural bio-waste, was used as a biosorbent for removal of rhodamine B (RhB), basic textile dye, from an aqueous solution. The effects of various experimental parameters were studied. The equilibrium data correlated well with a Freundlich isotherm (R² = 0.98–0.99) followed by a Halsey isotherm model (R² = 0.98–0.99) which indicated heterogeneity of the adsorbent surface and multilayer adsorption of RhB dye onto the water chestnut peel waste (WCPW). High correlation coefficients (R² = 0.99) together with close agreement between experimental q_e (0.4–1.7 mg g^?1) and calculated q_e (0.4–2.5 mg g^?1) suggested that the adsorption process followed pseudo-second-order kinetics, with k₂ values in the range of 52–3.4 × 10^?1 g mg^?1 min^?1 at different concentrations. The overall mechanism of adsorption was controlled by both liquid-film and intra-particle diffusions. The negative values of change in Gibb's free energy (?ΔG⁰ = 19.2–29.2 kJ mol^?1) and positive values of change in enthalpy (ΔH⁰ = 30.9–117.6 kJ mol^?1) revealed the process to be spontaneous and endothermic. WCPW was found to be an effective adsorbent for removal of RhB, a cationic dye, from an aqueous solution.     

Defluoridation of drinking water using Al3+-modified bentonite clay: optimization of fluoride adsorption conditions

Al³⁺-bentonite clay (Alum-bent) was prepared by ion exchange of base cations on the matrices of bentonite clay. Intercalation of bentonite clay with Al³⁺ was performed in batch experiments. Parameters optimized include time, dosage, and Al³⁺ concentration. Physicochemical characterization of raw and modified bentonite clay was done by X-ray fluorescence, X-ray diffraction, energy dispersive X-ray spectrometry attached to scanning electron microscopy, Brunauer–Emmett–Teller analysis, cation exchange capacity (CEC) by ammonium acetate method, and pH_pzc by solid addition method. Chemical constituents of water were determined by atomic absorption spectrometry (AAS), ion selective electrode (Crison 6955 Fluoride selective electrode) and a Crison multimeter probe. For fluoride removal, the effect of contact time, adsorbent dosage, adsorbate concentration, and pH were evaluated in batch procedures. The adsorption capacity of fluoride by modified bentonite clay was observed to be 5.7 mg g^?1 at (26 ± 2) °C room temperature. Maximum adsorption of fluoride was optimum at 30 min, 1 g of dosage, 60 mg L^?1 of adsorbate concentration, pH 2–12, and 1:100 solid/liquid (S/L) ratios. Kinetic studies revealed that fluoride adsorption fitted well to pseudo-second-order model than pseudo first order. Adsorption data fitted well to both the Langmuir and Freundlich adsorption isotherms, hence, confirming monolayer and multilayer adsorption. Alum-bent showed good stability in removing fluoride from ground water to below the prescribed limit as stipulated by World Health Organization. As such, it can be concluded that Alum-bent is a potential defluoridation adsorbent which can be applied in fabrication of point of use devices for defluoridation of fluoride-rich water in rural areas of South Africa and other developing countries. Based on that, this comparative study proves that Alum-bent is a promising adsorbent with a high adsorption capacity for fluoride and can be a substitute for conventional defluoridation methods.     

Removal of selenite using ‘waste’ Fe(III)/Cr(III) hydroxide: Adsorption kinetics and isotherms

Removal of selenite [Se (IV)] from aqueous solution on to industrial solid ‘waste’ Fe(III)/Cr(III) hydroxide as adsorbent was investigated in the present article. Maximum adsorption was found to be at pH 4.0. Pretreated Fe(III)/Cr(III) hydroxide was found to be more efficient for the removal of selenite compared to untreated adsorbent. Langmuir and Freundlich isotherms have been studied. The Langmuir adsorption capacity (Q ₀) of the pretreated and untreated adsorbents was found to be 15.63 and 6.04?mg?g^?1, respectively. The adsorption process fit into the second-order kinetics. Thermodynamic parameters show that the adsorption process is spontaneous and endothermic in the temperature range 32 to 60°C. Coexisting anions vanadate and phosphate significantly affect the adsorption of selenite for both the pretreated and untreated adsorbents. Molybdate, thiocyanate, sulphate, nitrate and chloride do not significantly affect the removal of selenite for pretreated adsorbent.     

Magnetic particles precipitated onto wheat husk for removal of methyl blue from aqueous solution

Magnetic particles prepared via co-precipitation and impregnated onto wheat husk (MN-WH) were used for the removal of methyl blue (MB) from aqueous solution. Experiments were conducted in a batch mode for optimization regarding pH, contact time, adsorbent dose, initial dye concentrations, and temperature. Maximum adsorption (98%) was achieved at pH 5. The adsorption data were fitted into pseudo-first, pseudo-second, intraparticle diffusion, and Elovich equation revealing that adsorption followed pseudo-second-order kinetics. The four most common isotherm models, i.e. the Langmuir, Freundlich, Tempkin, and Dubinin–Radushkevich (D–R), were used to evaluate the data, with the best fit to a Langmuir isotherm (R² = 0.996), followed by a Freundlich isotherm (R² = 0.995), indicating monolayer adsorption of MB on the surface of MN-WH. Thermodynamic parameters calculated from the Van't Hoff equation revealed that the adsorption is exothermic (ΔHº = ?19.7 kJ mol^?1).     

Removal of cadmium(II), lead(II), and chromium(VI) ions from aqueous solution using clay

Removal of cadmium(II), lead(II), and chromium(VI) from aqueous solution using clay, a naturally occurring low-cost adsorbent, under various conditions, such as contact time, initial concentration, temperature, and pH has been investigated. The sorption of these metals follows both Langmuir and Freundlich adsorption isotherms. The magnitude of Langmuir and Freundlich constants at 30°C for cadmium, lead, and chromium indicate good adsorption capacity. The kinetic rate constants (K _ad) indicate that the adsorption follows first order. The thermodynamic parameters: free energy change (ΔG ^o), enthalpy change (ΔH ^o), and entropy change (ΔS ^o) show that adsorption is an endothermic process and that adsorption is favored at high temperature. The results reveal that clay is a good adsorbent for the removal of these metals from wastewater.     

Adsorption of vanadate(V) on Fe(III)/Cr(III) hydroxide waste

Adsorption of vanadate(V) from aqueous solution onto industrial solid ‘waste’ Fe(III)/Cr(III) hydroxide was investigated. HCl treated Fe(III)/Cr(III) hydroxide was found to be more efficient for the removal of vanadate(V) compared to untreated adsorbent. The adsorption follows second-order kinetics. Langmuir and Freundlich isotherms have been studied. The Langmuir adsorption capacity (Q ₀) of the treated and untreated adsorbents was found to be 11.43 and 4.67 mg g⁻¹, respectively. Thermodynamic parameters showed that the adsorption process was spontaneous and endothermic in the temperature range 32–60°C. Maximum adsorption was found at system pH 4.0. The adsorption mechanism was predominantly ion exchange. Effect of other anions such as phosphate, selenite, molybdate, nitrate, chloride, and sulfate on adsorption of vanadium has been examined.     

Low-cost and efficient adsorbent derived from pyrolysis of Jatropha curcas seeds for the removal of Cu2+ from aqueous solutions

Biochar, is a low-cost material that can be used as an alternative adsorbent for the removal of heavy metals. In this study, a low-cost and efficient adsorbent synthesised from Jatropha curcas seeds was used for the uptake of Cu²⁺ from aqueous solutions. The as-prepared adsorbent was characterised by scanning electron microscopy and Brunauer–Emmett–Teller analysis post calcination at 500 °C, its BET surface area and total pore volume were 39.62?m²?g^?1 and 0.049?m³?g^?1, respectively. Subsequently, the effects of initial pH of the solution, contact time, and adsorbent material dosage on the adsorption of Cu²⁺ by the prepared adsorbent were investigated. The as-prepared adsorbent exhibited a high performance, with a maximum adsorption amount of 32.895?mg?g^?1 for Cu²⁺ at pH 5.0 and 25 °C, owing to the presence of ?OH, C=O, C–O, Si-O-Si, and O-Si-O on its surface. The predominant Cu²⁺ adsorption mechanism was assumed to be ion exchange. Notably, the Cu²⁺ adsorption could attain equilibrium within 90?min. In addition, the fact that the Langmuir model was a better fit than the Freundlich model for the isotherm data of Cu²⁺ adsorption by the as-prepared adsorbent suggested that the adsorption of Cu²⁺ was a monolayer adsorption process.     

Removal of Mo(VI) from aqueous solutions using sulfuric acid-modified cinder: kinetic and thermodynamic studies

Removal of Mo(VI) from aqueous solutions was investigated using cinder modified by sulfuric acid. Various parameters such as pH, agitation time, Mo(VI) concentration, and temperature have been studied. The maximum adsorption of Mo(VI) occurred at pH between 4.0 and 6.0. Kinetic studies showed that the adsorption generally obeyed a pseudo second-order model. The activation energy was 31.4?kJ?mol^?1, indicating that the adsorption process was governed mainly by interactions of physical nature. Furthermore, application of Langmuir and Freundlich isotherm models to the adsorption equilibrium data showed that the adsorption behavior obeyed the Langmuir model. The adsorption capacity was found to be 10.8?g Mo(VI)?kg^?1 adsorbent. Finally, thermodynamic parameters such as ΔH ⁰, ΔS ⁰, and ΔG ⁰ were also evaluated, which showed that the adsorption of Mo(VI) on the treated cinder was endothermic, entropy increasing, and spontaneous. In conclusion, the sulfuric acid-modified cinder was shown to be an inexpensive, effective, and simple adsorbent for the removal of Mo(VI) from water.     

Equilibrium,kinetic, and quantum chemical studies on the adsorption of Congo red using Imperata cylindrica leaf powder activated carbon

Leaf powder of spear grass, otherwise known as Imperata cylindrica (IC), was used to prepare activated carbon. The Imperata cylindrica activated carbon (ICAC) prepared was used for the removal of Congo red (CR) dye from aqueous solution. Operation parameters such as initial dye concentration, contact time, adsorbent dosage, pH, and temperature were studied in batch systems. Equilibrium was attained in 150 and 180?min at lowest and highest concentrations, respectively. Maximum adsorption was observed at pH 3. Quantum chemical studies suggested that the protonation of aniline groups and minimal molecular size at planar geometry coupled with electrostatic interaction enhances the adsorption at low pH. Adsorption data were tested using pseudo-first-order and second-order reaction kinetics; the latter was found to be more suitable with a coefficient of determination of ≥0.99. The adsorption process fits Langmuir isotherm model better than the Freundlich model, with a maximum monolayer coverage of 313?mgg^?1. This study shows that ICAC is effective in removing CR dye from aqueous solutions.     

Removal of C.I. acid brown 75 from aqueous solution by kaolinite

The adsorption of acid brown 75 onto kaolinite in aqueous solution was studied with respect to the pH, adsorbent dosage, contact time, initial concentration, and operating temperature. Desorption of dye from dye-saturated kaolinite was observed. Experimental data indicated that the adsorption capacity of kaolinite for the dye was higher in acidic rather than in basic solution. The maximum adsorption capacity of kaolinite towards the dye was found to be 96.5 mg g^?1 (pH 1.0). At the optimal adsorption condition, the dye removal ratio was 95.5%. Dye-saturated kaolinite could desorb at aqueous NaOH, the desorption ratio of dye was 78.8%. The linear Langmuir and Freundlich isotherm models are well fitting to represent the experimental data.     

Heavy metals uptake from aqueous solutions using marine algae (Colpomenia sinuosa): kinetics and isotherms

The adsorption of copper, zinc, cobalt, lead and cadmium ions onto Colpomenia sinuosa was studied as a function of contact time, initial metal ion concentration and initial pH. In addition, desorption studies were performed. Characterisation of this adsorbent was also confirmed by Fourier transform infrared (FTIR) spectroscopy and scanning electron microscopy (SEM) analysis. Batch adsorption experimental data were analysed using Langmuir, Freundlich and Dubinin–Raduschkevich (D–R) adsorption isotherms. The results indicated that the biosorption equilibrium was well described by both the Freudlich and D–R isotherms. Moreover, sorption kinetics was performed and it was observed that equilibrium was reached in<60 min, which could be described by the pseudo-second-order kinetic model for all heavy metals. The sorption of heavy metals onto the biomass was largely dependent on the initial solution pH. The elution efficiency for heavy metal ions desorption from C. sinuosa was determined for 0.1 M HCl, 1.0 M HCl and 1.0 M HNO₃. Desorption efficiency and also adsorption capacity were highest for Pb(II). The results indicate that C. sinuosa has great potential for the removal of heavy metals in an ecofriendly process.     

Determination of sorbent point zero charge: usefulness in sorption studies

Potentiometric mass titration (PMT) technique has been adapted to determine the pH _pzc of four vegetable wastes: grape stalks, cork, yohimbe bark and olive stones wastes used for Cu(II) removal. The pH at the point zero charge (pH _pzc), determined by PMT, are compared with that obtained by two classical techniques: mass titration (MT) and immersion technique (IT). PMT has been found to be an easy and appropriate technique to determine pH _pzc of the studied materials. From the results, the knowledge of sorbents pH _pzc provides information about the possible attraction and repulsion between sorbent and sorbate but in any case enables to ensure that electrostatic force is one of the mechanisms that takes place in metal sorption.     

Adsorption of cationic and anionic surfactants onto organic polymer resin Lewatit VPOC 1064 MD PH

The adsorption of a cationic (CTAB, cetyl trimethylammonium bromide) and an anionic surfactant (SLES, sodium dodecylethersulfate) from aqueous solution onto organic polymer resin (Lewatit VPOC 1064 MD PH) was studied. A series of batch experiments were performed to determine the sorption isotherms of surfactants to organic polymer resin. The experimental studies were analyzed by Langmuir and Freundlich isotherms. Furthermore, the isotherm parameters, average percentage errors (ε) of model data, and separation factor (R _L) were calculated. Other factors influencing the adsorption capacity (contact time, adsorbent amount, and initial surfactant concentration) were also discussed. The experimental data fitted very well to the Langmuir equilibrium model in the studied concentration range. The calculated R _L values showed that the adsorption of both surfactants were favorable. Among the surfactants, CTAB showed higher adsorption capacity onto organic polymer resin compared to SLES (Q ⁰ = 250 and 34.36 mg g⁻¹, respectively).     

Removal of congo red and basic violet 1 by chir pine (Pinus roxburghii) sawdust,a saw mill waste: batch and column studies

The efficiency of chir pine sawdust (CPS) for adsorptive removal of the dyes, congo red (CR) and basic violet 1 (BV), from aqueous solution was evaluated using batch and column studies. The equilibrium was attained in 60 min for CR and 45 min for BV. The adsorption of BV obeyed the Langmuir isotherm model while the Freundlich isotherm fitted the equilibrium data of CR adsorption. The Langmuir monolayer adsorption capacities (Q_o) of CPS for BV and CR were 11.3 and 5.8 g kg^?1, respectively. The kinetic data for CR were best fitted to the Lagergren pseudo-first-order model and for BV to the pseudo-second-order model. The intra-particle diffusion was found to be the rate-controlling step for CR adsorption, while the adsorption kinetics of BV were controlled by both intra-particle and liquid-film diffusion. The thermodynamic parameters indicated that the adsorption process was spontaneous and endothermic in nature. The adsorption activation energy (E_a) for CR (124 kJ mol^?1) implied chemical adsorption while that for BV (5.4 kJ mol^?1) indicated physical adsorption. An increase in the Thomas model constant (K_Th) with increasing flow indicated that for both dyes the mass transport resistance decreased during adsorption. Thus, CPS may be an efficient low-cost adsorbent for decolorization of dye-containing wastewaters.     

Physicochemical aspects of using natural scavengers in removing methylene blue (basic dye) from solution

Effluent from dyeing and finishing processes is an important source of water pollution. The effectiveness of bentonite, kaolinite and sediment from a local deposit in removing methylene blue as a cationic dye from aqueous solutions has been investigated. The adsorption equilibrium (isotherm) has been determined according to Freundlich and Langmuir equations. The optimum amount is 0.5 g for all adsorbents, and the optimum pH ranges are 2–8 for bentonite and 2–6 for kaolinite and sediment. With respect to kinetic modelling, the adsorption of methylene blue on various adsorbents was fitted to a second-order equation. Also, the thermodynamic parameters were determined. The negative free energy values indicate the feasibility of the process and spontaneous nature of adsorption. The positive ΔH° values indicate the endothermic nature of the process. Thus, Egyptian clay minerals and sediments have a great tendency to remove the dye from solutions.     

Ethylenediamine-modified activated carbon for aqueous lead adsorption

This study is to develop a carbon-based adsorbent containing multiple functional ligands for effective removal of lead ions from aqueous media. Activated carbon was oxidized by nitric acid, followed by chlorination with thionyl chloride and reaction with ethylenediamine. Modified activated carbon (MAC) was characterized using scanning electron microscopy in conjunction of energy dispersive spectroscopy (SEM-EDS), Fourier transform infrared spectroscopy (FT-IR), and potentiometric titration. Surface characterizations confirmed that carboxyl, amine, and chlorine functional groups were effectively introduced onto the carbon surface by the treatments. The modifications lowered the pH at the point of zero charge (pH_pzc) from 9.6 to 2.55 and resulted in more negatively charged surfaces. Adsorptive experiments showed that aqueous Pb removal by MAC was faster, with a 62% higher capacity than the original activated carbon (60.2 vs. 37.2 mg g⁻¹).     

Modeling of adsorption isotherms and kinetics of uranium sorption by magnetic ion imprinted polymers

Application of magnetic U(VI) ion imprinted polymers (IIPs) coated on magnetic nanoparticles was investigated for pre-concentration and determination of U(VI) ions in aqueous solutions. The scanning electron micrographs revealed the microporosity of the adsorbent. Uranium leaching was successful as the energy-dispersive X-ray spectra showed. The Brunauer–Emmett–Teller (BET) surface area improved by more than 13-fold (83.1 and 6.2 m² g^?1 for the leached and unleached magnetic IIP, respectively). U(VI) uptake was optimized using batch experiments with parameters affecting the uptake performance, such as initial uranium concentration, pH, contact time, and adsorbent dose investigated. Pseudo-second-order kinetics and the Langmuir isotherm model best fitted the experimental data. The maximum adsorption capacity of uranium onto the activated magnetic IIP reached 5.4 mg g^?1. The selectivity order was determined to be U(VI) > Ni(II) > Th(IV).