Preparation and characterization of <Emphasis Type="Italic">β</Emphasis>-FeOOH-coated sand and its adsorption of Cr(VI) from aqueous solutions

Batch adsorption experiments were conducted to explore the adsorption of Cr(VI) in aqueous solutions by β-FeOOH-coated sand. We investigated the key factors which affected the adsorption process such as adsorbent dosage, initial pH, initial Cr(VI) ion concentration, contact time and temperature. The uptake of Cr(VI) was very rapid and 44.3%, 51.6%, 58.9% of the adsorption happened during the first 180 minutes at 293K, 303K and 313K, respectively. The pseudo-second-order rate equation successfully described the adsorption kinetics. To study the adsorption isotherm, two equilibrium models, the Langmuir and Freundlich isotherms, were adopted. At 293K, 303K and 313K, the adsorption capacities obtained from the Langmuir isotherm were 0.060, 0.070 and 0.076 mg Cr(VI) per gram of the adsorbent, respectively. Thermodynamic parameters such as the change of energy, enthalpy and entropy were calculated using the equilibrium constants. The negative value of ΔG ⁰ and the positive value of ΔH ⁰ showed that the adsorption of Cr(VI) in aqueous solutions by β-FeOOH-coated sand was spontaneous, endothermic and occurred by physisorption.     

Removal of chromium(VI) by ZnCl2 activated coir pith carbon

The adsorption of chromium(VI) onto ZnCl₂ activated carbon developed from coir pith was investigated to assess the possible use of this adsorbent. The influence of contact time, adsorbent dose, Cr(VI) concentration, pH and temperature were investigated. The two theoretical adsorption isotherms, namely, Langmuir and Freundlich were used to describe the experimental results. The Langmuir adsorption capacity (Q ₀) was found to be 120.5?mg Cr(VI) per g of the adsorbent. The adsorption followed the second-order kinetics and was found to be maximum at pH 2.0. The pH effect and the desorption studies showed that ion exchange mechanism might be involved in the adsorption process. The effects of foreign ions such as chloride, sulphate, phosphate, selenite, molybdate, nitrate and perchlorate on the removal of Cr(VI) have been investigated. The removal of Cr(VI) from synthetic ground water was also tested. The results show that ZnCl₂ activated coir pith carbon is effective for the removal of Cr(VI) from water.     

Removal of selenite using ‘waste’ Fe(III)/Cr(III) hydroxide: Adsorption kinetics and isotherms

Removal of selenite [Se (IV)] from aqueous solution on to industrial solid ‘waste’ Fe(III)/Cr(III) hydroxide as adsorbent was investigated in the present article. Maximum adsorption was found to be at pH 4.0. Pretreated Fe(III)/Cr(III) hydroxide was found to be more efficient for the removal of selenite compared to untreated adsorbent. Langmuir and Freundlich isotherms have been studied. The Langmuir adsorption capacity (Q ₀) of the pretreated and untreated adsorbents was found to be 15.63 and 6.04?mg?g^?1, respectively. The adsorption process fit into the second-order kinetics. Thermodynamic parameters show that the adsorption process is spontaneous and endothermic in the temperature range 32 to 60°C. Coexisting anions vanadate and phosphate significantly affect the adsorption of selenite for both the pretreated and untreated adsorbents. Molybdate, thiocyanate, sulphate, nitrate and chloride do not significantly affect the removal of selenite for pretreated adsorbent.     

A review for chromium removal by carbon nanotubes

Water pollution is still a serious problem for the entire world. Adsorption technology is a promising process which is based on the fabrication of novel, cheap, non-dangerous and highly sorptive materials for application in wastewater purification processes. Nanomaterials are functional groups which find use in many important fields such as medicine, food processing and agriculture. This review collects information from published works about the use of carbon nanotubes as efficient and promising adsorbents in chromium removal from (real or synthesised) wastewater. For this purpose, isotherm (Langmuir, Freundlich, etc.), kinetic (pseudo-first-, second-order, etc.), thermodynamic (free-energy Gibbs, enthalpy, entropy) and desorption–regeneration studies were discussed in detail. Moreover, significant factors such as pH, agitation time, temperature, adsorbent dosage and initial dye concentration are also reported extensively. The maximum monolayer adsorption capacities of Cr(III) and Cr(VI) ions were 0.39–238.09 and 1.26–370.3?mg/g, respectively. The absolute values of ΔG⁰ and ΔH⁰ ranged 0.237–48.62 and 0.16–58.43?kJ/mol, respectively.     

Removal of congo red and basic violet 1 by chir pine (Pinus roxburghii) sawdust,a saw mill waste: batch and column studies

The efficiency of chir pine sawdust (CPS) for adsorptive removal of the dyes, congo red (CR) and basic violet 1 (BV), from aqueous solution was evaluated using batch and column studies. The equilibrium was attained in 60 min for CR and 45 min for BV. The adsorption of BV obeyed the Langmuir isotherm model while the Freundlich isotherm fitted the equilibrium data of CR adsorption. The Langmuir monolayer adsorption capacities (Q_o) of CPS for BV and CR were 11.3 and 5.8 g kg^?1, respectively. The kinetic data for CR were best fitted to the Lagergren pseudo-first-order model and for BV to the pseudo-second-order model. The intra-particle diffusion was found to be the rate-controlling step for CR adsorption, while the adsorption kinetics of BV were controlled by both intra-particle and liquid-film diffusion. The thermodynamic parameters indicated that the adsorption process was spontaneous and endothermic in nature. The adsorption activation energy (E_a) for CR (124 kJ mol^?1) implied chemical adsorption while that for BV (5.4 kJ mol^?1) indicated physical adsorption. An increase in the Thomas model constant (K_Th) with increasing flow indicated that for both dyes the mass transport resistance decreased during adsorption. Thus, CPS may be an efficient low-cost adsorbent for decolorization of dye-containing wastewaters.     

Low-cost and efficient adsorbent derived from pyrolysis of Jatropha curcas seeds for the removal of Cu2+ from aqueous solutions

Biochar, is a low-cost material that can be used as an alternative adsorbent for the removal of heavy metals. In this study, a low-cost and efficient adsorbent synthesised from Jatropha curcas seeds was used for the uptake of Cu²⁺ from aqueous solutions. The as-prepared adsorbent was characterised by scanning electron microscopy and Brunauer–Emmett–Teller analysis post calcination at 500 °C, its BET surface area and total pore volume were 39.62?m²?g^?1 and 0.049?m³?g^?1, respectively. Subsequently, the effects of initial pH of the solution, contact time, and adsorbent material dosage on the adsorption of Cu²⁺ by the prepared adsorbent were investigated. The as-prepared adsorbent exhibited a high performance, with a maximum adsorption amount of 32.895?mg?g^?1 for Cu²⁺ at pH 5.0 and 25 °C, owing to the presence of ?OH, C=O, C–O, Si-O-Si, and O-Si-O on its surface. The predominant Cu²⁺ adsorption mechanism was assumed to be ion exchange. Notably, the Cu²⁺ adsorption could attain equilibrium within 90?min. In addition, the fact that the Langmuir model was a better fit than the Freundlich model for the isotherm data of Cu²⁺ adsorption by the as-prepared adsorbent suggested that the adsorption of Cu²⁺ was a monolayer adsorption process.     

Ackee apple (Blighia sapida) seeds: a novel adsorbent for the removal of Congo Red dye from aqueous solutions

The ability of ackee apple (AA) seeds to remove Congo Red (CR) dye from aqueous solution was investigated. AA was characterised using thermo gravimetric analyser, scanning electron microscopy, Braunauer Emmett Teller, pH_pzc, elemental analysis and Boehm titration. The effects of operational parameters such as adsorbent dosage, contact time, initial dye concentration and solution pH were studied in a batch system. pH has a profound influence on the adsorption process. Maximum dye adsorption was observed at pH 3.0. The reaction was fast, reaching equilibrium in 90 min. Adsorption data were best described by Langmuir isotherm and the pseudo-second-order kinetic model with a maximum monolayer coverage of 161.89 mg·g^?1. Both boundary layer and intraparticle diffusion mechanisms were found to govern the adsorption process. Thermodynamic parameters such as standard free energy change (Δ G ⁰), standard enthalpy change (Δ H ⁰), and standard entropy change (Δ S ⁰) were studied. Values of Δ G ⁰ varied between?30.94 and?36.56 kJ·mol^?1, Δ H ⁰ was 25.61 kJ·mol^?1, and Δ S ⁰ was 74.84 kJ·mol^?1·K^?1, indicating that the removal of CR from aqueous solution by AA was spontaneous and endothermic in nature. Regeneration and reusability studies were carried out using different eluents. AA gave the highest adsorption efficiency up to four cycles when treated with 0.3 M HCl. AA was found to be an effective adsorbent for the removal of CR dye from aqueous solution.     

Modeling of adsorption isotherms and kinetics of uranium sorption by magnetic ion imprinted polymers

Application of magnetic U(VI) ion imprinted polymers (IIPs) coated on magnetic nanoparticles was investigated for pre-concentration and determination of U(VI) ions in aqueous solutions. The scanning electron micrographs revealed the microporosity of the adsorbent. Uranium leaching was successful as the energy-dispersive X-ray spectra showed. The Brunauer–Emmett–Teller (BET) surface area improved by more than 13-fold (83.1 and 6.2 m² g^?1 for the leached and unleached magnetic IIP, respectively). U(VI) uptake was optimized using batch experiments with parameters affecting the uptake performance, such as initial uranium concentration, pH, contact time, and adsorbent dose investigated. Pseudo-second-order kinetics and the Langmuir isotherm model best fitted the experimental data. The maximum adsorption capacity of uranium onto the activated magnetic IIP reached 5.4 mg g^?1. The selectivity order was determined to be U(VI) > Ni(II) > Th(IV).     

Removal of cadmium(II), lead(II), and chromium(VI) ions from aqueous solution using clay

Removal of cadmium(II), lead(II), and chromium(VI) from aqueous solution using clay, a naturally occurring low-cost adsorbent, under various conditions, such as contact time, initial concentration, temperature, and pH has been investigated. The sorption of these metals follows both Langmuir and Freundlich adsorption isotherms. The magnitude of Langmuir and Freundlich constants at 30°C for cadmium, lead, and chromium indicate good adsorption capacity. The kinetic rate constants (K _ad) indicate that the adsorption follows first order. The thermodynamic parameters: free energy change (ΔG ^o), enthalpy change (ΔH ^o), and entropy change (ΔS ^o) show that adsorption is an endothermic process and that adsorption is favored at high temperature. The results reveal that clay is a good adsorbent for the removal of these metals from wastewater.     

Removal of Cr(VI) from aqueous solution using waste weed, Salvinia cucullata

Biosorption studies of Cr(VI) were carried out using waste weed, Salvinia cucullata. Various adsorption parameters were studied, such as agitation speed, contact time, pH, particle size, and concentrations of adsorbent and adsorbate. The equilibrium was achieved in 12 h. A lower pH favoured adsorption of Cr(VI). The kinetics followed pseudo-second-order rate equations. The adsorption isotherm obeyed both the Langmuir and Freundlich models. The calculated activation energy (1.1 kJ mol^-1) suggested that the adsorption followed a diffusion-controlled mechanism. Various thermodynamic parameters such as Δ G^°, Δ H^°, and Δ S^° were also calculated. The positive values of enthalpy indicated the endothermic nature of the reaction, and Δ S^° showed the increasing randomness at the solid liquid interface of Cr(VI) on the adsorbent, which revealed the ease of adsorption reaction. These thermo-dynamic parameters showed the spontaneity of the reaction. The maximum adsorption of uptake (232 mg g^-1) compared well with reported values of similar adsorbents. The rate-determining step was observed to follow an intra-particle diffusion model.     

Biosorption of Cr(VI) from wastewater using Sorghastrum Nutans L. Nash

Sorghastrum Nutans L. Nash is used as an adsorbent for the removal of Cr(VI) from wastewater. Adsorption coupled reduction i.e. indirect reduction is the mechanism of Cr(VI) removal by the biomaterial. The adsorbent surface became highly positively charged at lower pH, adsorption rate of Cr(VI) is faster and reduction reaction also accelerates at lower pH since the binding of negatively charged Cr(VI) ion species to the cationic groups is enhanced and protons take part in this reaction. The adsorbent is characterised by using XRD, FTIR, SEM and EDAX analysis. OH bending, CN stretching/bending and NH stretching play a major role in Chromium adsorption. Experimental values follow pseudo-second order reaction and Langmuir adsorption isotherm. Surface diffusion is the rate controlling mechanism for the process. The maximum percentage of Cr(VI) removal obtained is 75.5% with 7?g/L dosage at pH 1.3 and adsorbate concentration was 100?mg/L. From the normal probability, residual, contour, 3D surface, main effect and interaction plot along with t-test, ANOVA, and F-test, it is observed that pH has the most significant effect on the percentage removal followed by adsorbent dosage and time. The adsorbate concentration has the least effects and interaction effects are found to be significant.     

Adsorptive features of banana (Musa paradisiaca) stalk-based activated carbon for malachite green dye removal

Chemically prepared activated carbon derived from banana stalk (BSAC) was used as an adsorbent to remove malachite green (MG) dye from aqueous solution. BSAC was characterised using thermogravimetric analyser, Brunauer Emmett Teller, Fourier transform infrared spectrometry, scanning electron microscopy, pH_pzc, elemental analysis and Boehm titration. The effectiveness of BSAC in adsorbing MG dye was studied as a function of pH, contact time, temperature, initial dye concentration and repeated desorption–adsorption processes. pH_pzc of BSAC was 4.5 and maximum dye adsorption occurred at pH 8.0. The rate of dye adsorption by BSAC was very fast initially, attaining equilibrium within 120 min following a pseudo-second-order kinetic model. Experimental data were analysed by Langmuir, Freundlich and Dubinin–Raduschevich isotherms. Equilibrium data fitted best into the Langmuir model, with a maximum adsorption capacity of 141.76 mg·g^?1. Δ G ⁰ values were negative, indicating that the process of MG dye adsorption onto BSAC was spontaneous. The positive values of Δ H ⁰ and Δ S ⁰ suggests that the process of dye adsorption was endothermic. The regeneration efficiency of spent BSAC was studied using 0.5 M HCl, and was found to be in the range of 90.22–95.16% after four cycles. This adsorbent was found to be both effective and viable for the removal of MG dye from aqueous solution.     

Magnetic particles precipitated onto wheat husk for removal of methyl blue from aqueous solution

Magnetic particles prepared via co-precipitation and impregnated onto wheat husk (MN-WH) were used for the removal of methyl blue (MB) from aqueous solution. Experiments were conducted in a batch mode for optimization regarding pH, contact time, adsorbent dose, initial dye concentrations, and temperature. Maximum adsorption (98%) was achieved at pH 5. The adsorption data were fitted into pseudo-first, pseudo-second, intraparticle diffusion, and Elovich equation revealing that adsorption followed pseudo-second-order kinetics. The four most common isotherm models, i.e. the Langmuir, Freundlich, Tempkin, and Dubinin–Radushkevich (D–R), were used to evaluate the data, with the best fit to a Langmuir isotherm (R² = 0.996), followed by a Freundlich isotherm (R² = 0.995), indicating monolayer adsorption of MB on the surface of MN-WH. Thermodynamic parameters calculated from the Van't Hoff equation revealed that the adsorption is exothermic (ΔHº = ?19.7 kJ mol^?1).     

Biosorption potential of Cr(VI) by Kocuria sp. ASB107, a radio-resistant bacterium isolated from Ramsar,Iran

Heavy metal pollution in soil and wastewater is a worldwide environmental issue in which microorganisms play a significant role for its removal. In the present study, biosorption of Cr(VI) by the live and dead cells of Kocuria sp. ASB107, a radio-resistant bacterium, was investigated. The effect of contact time, solution pH, initial hexavalent chromium concentration and adsorbent dose on biosorption efficiency was studied. Also, live cells were further immobilised on various matrices by different techniques and then were examined for tolerance to chromium biosorption. Experimental results indicated that the removal efficiency of chromium increased with decrease in pH, initial Cr(VI) concentration, and also increase in adsorbent dose and the contact time. The maximum removal efficiency of live and dead cells at acidic pH of 4–4.5, contact time of 24 hours, adsorbent dose 1.6?g/100?mL and initial chromium concentration 25?mg/L were 82.4% and 69.2%, respectively. The adsorption data was described well by Langmuir isotherm model. Among all immobilisation techniques tested, cross-linking showed the highest biosorption of Cr(VI). Results indicated that live cells of Kocuria sp. ASB107 were better than dead ones.     

Lead(II) and cadmium(II) removal from aqueous solution using processed walnut shell: kinetic and equilibrium study

The biosorption potential of processed walnut shell for Pb(II) and Cd(II) ions from aqueous solutions was explored. The effects of pH, contact time, initial ion concentration, and amount of dried adsorbent were studied in batch experiments. The maximum adsorption was achieved within the pH range 4.0–6.0. The equilibrium data were well fitted by the Langmuir isotherm model. The maximum monolayer adsorption capacities were found to be 32?g?kg^?1 and 11.6?g?kg^?1 for Pb(II) and Cd(II) ions, respectively. Kinetic data were best described by the pseudo-second-order model. The structural features of the adsorbent were characterized by Fourier transform infrared spectroscopy, which confirmed the involvement of hydroxyl (–OH), carboxyl (–COO^–), and carbonyl (C=O) groups in metal sorption. This readily available adsorbent is efficient in the uptake of Pb(II) and Cd(II) ions from an aqueous solution and could be used for the treatment of wastewater streams bearing these metal ions.     

Granulation of gibbsite with inorganic binder and its ability to adsorb Mo(VI) from aqueous solution

In this study, we prepared a new adsorbent and evaluated its ability to adsorb Mo(VI). Gibbsite was granulated with colloidal alumina or colloidal silica. The amount of Mo(VI) adsorbed onto granular gibbsite with a binder, effect of contact time and pH on the adsorption of Mo(VI), and column experiments were investigated. The amount of Mo(VI) adsorbed was greater in the order of ST12 (colloidal silica, 12%)?相似文献   

Removal of Eu3+, Ce3+, Sr2+, and Cs+ ions from radioactive waste solutions by modified activated carbon prepared from coconut shells

As a biomass agricultural waste material, coconut shells were used for the preparation of high-quality modified activated carbon. Chemical modification of the surface of the prepared activated carbon is done by oxidation using H₂O₂ and HNO₃, respectively. The surface area and pore volume of the coconut shells activated carbon are increased by the chemical modification, and followingly the removal of the metals is improved. The structural morphology and composition of the modified activated carbon coconut shells (MACCS) were evaluated by Fourier transform infrared (FTIR) spectra, thermogravimetric analysis–differential thermal analysis (TGA-DTA), scanning electron microscope (SEM), X-ray diffraction (XRD), surface area analysis (SAA), X-ray fluorescence (XRF), and carbon, hydrogen, nitrogen, and sulfur (CHNS) elemental analysis. The prepared MACCS has reasonably good chemical stability. The influence of solution pH, contact time, adsorbent dosage, adsorption temperature, initial metal concentrations, and interfering ions on the adsorption performance of the investigated ions onto the prepared sorbent was examined by a batch method. The selectivity sequence for sorption of Eu³⁺, Ce³⁺, Sr²⁺, and Cs⁺ ions on MACCS was found to be Eu^3+?>?Ce^3+?>?Sr^2+?>?Cs⁺. The saturation capacities of MACCS for the studied metal ions were found to be 136.84, 85.55, 69.85, and 60.00?mg?g^?1 for Eu³⁺, Ce³⁺, Sr²⁺, and Cs⁺ ions, respectively. The thermodynamic parameters, ΔH°, ΔS°, and ΔG° were also evaluated.     

Ionic dye adsorption by zinc oxide nanoparticles

The adsorption behaviour of Basic Red 12, Acid Orange 7 and Acid Blue 1 on zinc oxide nanoparticles (ZNP) has been investigated to understand the physicochemical process involved and to explore the possible use of nanoparticles in the treatment and management of textile waste matter. The dye removal capacity of ZNP towards Basic Red 12, Acid Orange 7 and Acid Blue 1 was found to be 15.64, 6.78 and 6.38 mg g^?1, respectively. The adsorption process was pH dependent and optimum pH values of 9.0, 2.0 and 4.0 were obtained for Basic Red 12, Acid Orange 7 and Acid Blue 1, respectively. Equilibrium was established after 1.0 h for all dyes. Langmuir, Freundlich and Temkin isotherm models were applied to the system. The adsorbent ZNP was characterised using scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET) and Fourier transform infrared (FTIR) techniques. SEM analysis revealed the noticeable nanoporous morphology of the material. The results of FTIR spectroscopy showed that the process is driven by an electrostatic complexation mechanism. XRD studies revealed the nanocrystalline structure of ZNP. BET surface area measurement suggested a high pore volume and large surface area for the adsorbent. The kinetic measurements suggested pseudo-second-order kinetic processes with high regression coefficients and smaller standard error of estimate values and lower residual sum of squares. The thermodynamic measurements suggested that all processes were exothermic and accompanied by negative values for Δ G⁰, Δ S⁰ and Δ H⁰.     

Equilibrium,kinetic, and quantum chemical studies on the adsorption of Congo red using Imperata cylindrica leaf powder activated carbon

Leaf powder of spear grass, otherwise known as Imperata cylindrica (IC), was used to prepare activated carbon. The Imperata cylindrica activated carbon (ICAC) prepared was used for the removal of Congo red (CR) dye from aqueous solution. Operation parameters such as initial dye concentration, contact time, adsorbent dosage, pH, and temperature were studied in batch systems. Equilibrium was attained in 150 and 180?min at lowest and highest concentrations, respectively. Maximum adsorption was observed at pH 3. Quantum chemical studies suggested that the protonation of aniline groups and minimal molecular size at planar geometry coupled with electrostatic interaction enhances the adsorption at low pH. Adsorption data were tested using pseudo-first-order and second-order reaction kinetics; the latter was found to be more suitable with a coefficient of determination of ≥0.99. The adsorption process fits Langmuir isotherm model better than the Freundlich model, with a maximum monolayer coverage of 313?mgg^?1. This study shows that ICAC is effective in removing CR dye from aqueous solutions.