Comparing electron ionization high-resolution and electron capture low-resolution mass spectrometric determination of polybrominated diphenyl ethers in plasma, serum and milk

Gas chromatography coupled to low-resolution mass spectrometry with electron capture negative ionization as detection mode (GC-LRMS (ECNI)) has been compared to gas chromatography coupled to high-resolution mass spectrometry using electron ionization as detection mode (GC-HRMS (EI)) for determination of polybrominated diphenyl ethers (PBDEs) in biological samples. Extracts of 5.0 g plasma, serum and milk samples were analyzed using both methods. The GC-LRMS (ECNI) and GC-HRMS (EI) systems were found to be equally well suited for determination of PBDEs in the biological samples, as well as in standard solutions, with respect to response, detection limits and repeatability at the pg-level. The estimated limits of detection (LOD) in milk extracts ranged from 0.3-0.6 pg PBDE/g milk and 0.4-0.7 pg PBDE/g milk, for the GC-LRMS (ECNI) and GC-HRMS (EI) systems, respectively. The method repeatability including sample preparation was in the range 4.7-8.4% and 0.6-10% relative standard deviation (RSD) for the GC-LRMS (ECNI) and GC-HRMS (EI) systems, respectively.     

Secondary ozonides of substituted cyclohexenes: a new class of pollutants characterized by collision-induced dissociation mass spectrometry using negative chemical ionization

Recent studies indicate that secondary ozonides of cyclic alkenes are formed in atmospheric reactions and may be relatively stable. The secondary ozonides (SOZs) of cyclohexene (1), 1-methylcyclohexene (2), 4-isopropyl-1-methylcyclohexene (3) and 4-isopropenyl-1-methylcyclohexene (limonene) (4) have been characterized by rapid gas chromatography electron ionization (EI), negative and positive chemical ionization (CI: ammonia, isobutane and methane) and collision-induced dissociation (CID) mass spectrometry. Both EI and positive CI spectra were found unsuitable for reproducible analysis. However, negative CI showed stable (M−H)⁻ ions with minor fragmentation. CID of the (M−H)⁻ ions resulted in simple and reproducible fragmentation patterns for all four SOZs with loss of m/z 18, 44 and 60, tentatively assigned as H₂O, CO₂ and C₂H₄O₂ or CO₃, respectively. Thus, negative CI-MS–MS in combination with rapid gas chromatography is the preferred method for identification of secondary ozonides of cyclohexenes.     

Biological effects of diethylene glycol (DEG) and produced waters (PWs) released from offshore activities: A multi-biomarker approach with the sea bass Dicentrarchus labrax

Diethylene glycol (DEG) is largely used during oil and gas exploitation by offshore platforms. The aim of this work was to investigate if this compound induces direct molecular/cellular effects in marine organisms, or indirectly modulate those of produced waters (PWs). Sea bass (Dicentrarchus labrax) were exposed to DEG dosed alone or in combination with PWs from an Adriatic platform. A wide array of analysed biomarkers included cytochrome P450-dependent enzymatic activity, bile metabolites, glutathione S-transferases, acetylcholinesterase, peroxisomal proliferation, antioxidant defences (catalase, glutathione reductase, glutathione peroxidases, glutathione), total oxyradical scavenging capacity, malondialdehyde and DNA integrity (single strand breaks and frequency of micronuclei). Results did not reveal marked effects of DEG, while PWs influenced the biotransformation system, the oxidative status and the onset of genotoxic damages. Co-exposures caused only limited differences of biomarker responses at some experimental conditions, overall suggesting a limited biological impact of DEG at levels normally deriving from offshore activities.     

Synthesis, isolation and purification of C10-C13 polychloro-n-alkanes for use as standards in environmental analysis

Short chain (C10-C13) polychloro-n-alkanes (sPCAs) mixtures were synthesized by refluxing pure n-alkane (> 99%) with sulfuryl chloride (SO2Cl2) in the presence of UV-light (550 W). The free radical initiated reactions produced analogs containing approximately 4-9 chlorine atoms on each carbon chain. Purification of reaction products was achieved by adsorption chromatography on Florisil. The products were characterized by high-resolution gas chromatography/mass spectrometry (HRGC/MS) operated in the electron capture negative ionization (ECNI) and in electron ionization (EI) modes. Individual standards can now be combined to create standards whose profiles resemble that of environmental samples. Quantification of a known amount of the newly synthesized sPCAs mixture, using an industrial formulation as an external standard, resulted in an overestimation (approximately 28%) in its true value.     

Dioxin like compounds from municipal waste incinerator emissions: assessment of the presence of polychlorinated naphthalenes

Polychloronaphthalenes (PCN) were identified and quantified in emission samples collected from five different municipal waste incinerators (MWI). Polychlorodibenzo-p-dioxins (PCDD) and polychlorodibenzofurans (PCDF) were also determined to find a possible relationship between these classes of organochlorinated compounds. The analyses of PCDD/PCDF and PCN were carried out by high resolution gas chromatography coupled with high resolution mass spectrometry using a positive electron ionization source and operating in the selected ion monitoring analyzer mode (HRGC-HRMS/EI(+)-SIM). The total levels of PCN varied from 1.08 up to 21.36 ng/Nm3 (mono- to octachlorinated) and 0.33 to 5.72 ng/Nm3 (tetra- to octachlorinated), whereas the levels of PCDD/PCDF ranged between 1.14 and 276.26 ng/Nm3 (0.01 and 5 ng I-TEQ/Nm3), depending on the type of the MWI. These findings do not corroborate a PCN and PCDD/PCDF correlation.     

Sampling and Analysis of Volatile Organic Compounds Evolved During Thermal Processing of Acrylonitrile Butadiene Styrene Composite Resins

Abstract

The evaluation of emissions of volatile organic compounds (VOCs) during processing of resins is of interest to resin manufacturers and resin processors. An accurate estimate of the VOCs emitted from resin processing has been difficult due to the wide variation in processing facilities. This study was designed to estimate the emissions in terms of mass of emitted VOC per mass of resin processed.

A collection and analysis method was developed and validated for the determination of VOCs present in the emissions of thermally processed acrylonitrile butadiene styrene (ABS) resins. Four composite resins were blended from automotive, general molding, pipe, and refrigeration grade ABS resins obtained from the manufacturers. Emission samples were collected in evacuated 6-L Summa canisters and then analyzed using gas chromatography/flame ionization detection/mass selective detection (GC/FID/MSD). Levels were determined for nine target analytes detected in canister samples, and for total VOCs detected by an inline GC/FID. The emissions evolved from the extrusion of each composite resin were expressed in terms of mass of VOCs per mass of processed resin. Styrene was the principal volatile emission from all the composite resins. VOCs analyzed from the pipe resin sample contained the highest level of styrene at 402 μg/g. An additional collection and detection method was used to determine the presence of aerosols in the emissions. This method involved collecting particulates on glass fiber filters, extracting them with solvents, and analyzing them using gas chromatography/mass spectrometry (GC/MS). No significant levels of any of the target analytes were detected on the filters.     

Determination of dimethyl fumarate (DMFu) in silica gel pouches using gas chromatography coupled ion trap mass spectrometry

A simple method for the determination of dimethyl fumarate (DMFu) in silica gel pouches has been developed. The gas chromatographic behaviour of DMFu was investigated; the instrumental method, based on EI mass spectrometry coupled with an Ion Trap Detector operating whether in full scan mode or in MS/MS mode was also investigated. Several factors have been evaluated and optimized during the development process: solvent and temperature of extraction, type of stationary phase in capillary column. The analytical procedure consists of two steps as follows: (a) the sample preparation using 10 g of sample extracted with acetonitrile in an ultrasonic, heated bath and (b) the determination by gas chromatography-ion trap mass spectrometry. Mass spectrometry in conjunction with chromatographic separation is a very powerful combination for identification of an analyte in the extract in spite of selective detectors employed with GC, such as ECD, FPD and NPD, that offer only limited specificity. Blank samples show no interfering peaks in the areas of interest, so the specificity of the method was assured under the investigated GC/MS conditions. The method has been validated in terms of recovery, repeatability, linearity, detection limits and measurement uncertainty. The results obtained meet both the method validation criteria and requirements of the European/National legislation. The method was verified to be accurate with 97 % mean recoveries at 0.05 mg/kg and 1.00 mg/kg levels; the repeatability (expressed as RSD %) was found to be better than 15 %. Good linearity was found in the range between 0.05 μg/mL and 5.0 μg/mL and a value of R2 > 0.9998 was calculated. The procedure ensures high specificity and a good sensitivity with detection limit (ld) of 0.02 mg/kg and quantification limit (LOQ) of 0.05 mg/kg. This procedure has been successfully applied for the analysis of several hundred of real samples collected during a monitoring control plan started last year in our country. All samples exceeding the maximum allowed level of DMFu (0, 1 mg/kg) were confirmed by GC/MS/MS (ITD) for a higher degree of confidence in identification. The main advantages of this method include: rapidity, simplicity (few, simple steps), reliability, cheapness, no need for long and difficult clean-up and evaporation steps, high specificity by using GC/MS and GC/MS/MS, availability for routine monitoring.     

Low-resolution mass spectrometric relative response factors (RRFs) and relative retention times (RRTs) on two common gas chromatographic stationary phases for 87 polychlorinated dibenzofurans

All 87 tetra- to octa-chlorinated dibenzofurans (PCDFs) were analysed using high-resolution gas chromatography/low-resolution mass spectrometry (HRGC-LRMS). The mass spectrometer was operated in two different modes: electron ionisation (EI), and negative ion chemical ionisation (NCI) with methane as a reagent gas. Baseline separation and identification of all PCDF congeners was carried out using one non-polar (DB-5) and one polar (RT-2330) capillary GC column. Relative retention times (RRTs) on both columns, and relative response factors (RRFs) in both EI- and NCI-modes, were calculated for all 87 of the PCDFs. Comparison of the EI-RRFs and NCI-RRFs showed that the mass spectrometric NCI-responses varied to a higher degree than the EI-responses. The level of NCI-response was dependent on the substitution positions of the chlorine atoms on the dibenzofuran molecule skeleton. The ratio between the highest and lowest RRFs was 26 in the NCI-mode, but only 2.3 in the EI-mode. Thus, quantification of tetra- to octa-CDFs in environmental samples using the NCI-mode will result in incorrect estimates of PCDF concentrations unless 13C-labelled internal standards are used for each congener, or RRFs are taken into consideration. In contrast, the quantification of PCDFs in the EI-mode using a single internal 13C-labelled PCDF standard for each PCDF homologue is accurate according to the findings in this investigation. A flue gas sample from a municipal solid waste incinerator (MSWI) analysed in the NCI-mode was quantified with and without NCI-RRFs. When using NCI-RRFs the reported concentration of SigmaPCDFs in the flue gas sample increased by 40%. Furthermore, TCDF analysis was compared using two mass spectrometers (a VG 12-250 and a Finnigan 4500) operating in EI-mode. These quadrupole instruments performed equally well, giving similar EI-RRFs for the tested compounds.     

Identification of dimethylchloroarsine near a former herbicide factory by headspace solid-phase microextraction gas chromatography-mass spectrometry

The application of an improved method based on multidetector gas chromatography to the determination of trace levels of organoarsines in complex matrices is described. The method using headspace-mode solid-phase microextraction (SPME) was applied to a carefully sampled and preserved freshwater sediment core obtained from central Green Bay, Lake Michigan. The sediment core was collected and fractionated in an inert atmosphere. A carboxen/ polydimethylsiloxane-coated SPME fiber (85 microm film thickness) was equilibrated (n = 4) for 60 min at 25 degrees C in the headspace of the sample vessel before introduction to the chromatograph. Conventional quadrupole ion trap mass spectrometry (electron impact ionization), electron capture detection, and pulsed flame photometric detection (arsenic mode) were employed for structure elucidation. A heretofore unidentified species in this region, dimethylchloroarsine (DMCA). was identified. The mass spectrum for DMCA is interpreted based on the observed fragmentation pattern. A bimodal vertical distribution of DMCA in the sediment core sample was observed and its interpretation based on Pb-210 dating is reported.     

Polychlorinated biphenyls in contaminated soil samples evaluated by GC-ECD with dual-column and GC-HRMS

We present and compare results obtained from the analysis of polychlorinated biphenyls (PCBs) of a limited number of contaminated soil samples collected in three areas of Basilicata region (south of Italy). The levels of PCBs were evaluated by using two analytical methods: (i) parallel dual-column gas-chromatography with dual electron capture detectors (GC-ECD) and (ii) gas-chromatography coupled to high-resolution mass spectrometry (GC-HRMS) via electron impact ionization (EI) in the multiple ion monitoring mode (MIM, two ions per compound). Two extraction methods prior to sample cleanup were also examined: microwave-assisted extraction (MAE) and ultrasonic-assisted extraction (UAE). The MAE was the extraction procedure adopted using acetone/n-hexane (1:1, v/v) as it is mainly characterized by higher sample throughput and allowed reduced consumption of organic solvents. While extraction and analysis of spiked soil samples showed the applicability of both methods, systematic differences between the results were obtained for the sum of PCBs as a result of some non-detected congeners by GC-ECD compared with GC-HRMS. Indeed, high resolution MS using EI mode (electron energy 40eV) with a resolving power of 10,000 provides additional information about the contamination pattern. The GC-ECD screening of 11 soil samples led to just one sample non-compliant to as it was close to the guide value for soils fixed by the Italian legislation (i.e., 60ppb for private or urban soil). Using GC-HRMS, the amount of all PCBs found ranged from 5.4 to 127ppb with five soil samples non-compliant to the guide value. The number of identified congeners ranged from 1 to 9 and 9 to 18 using dual-column GC-ECD and GC-HRMS, respectively.     

Analysis of halogenated polycyclic aromatic hydrocarbons in urban air, snow and automobile exhaust

Urban air, snow and automobile exhaust samples were extensively cleaned up by open column liquid chromatography. The appropriate fractions were analysed for halogenated polycyclic aromatic hydrocarbons (XPAH) by gas chromatography/negative chemical ionization mass spectrometry (GC/NCIMS). XPAH were found in all three sample types. A urban air sample was found to contain chlorinated pyrenes, fluoranthenes and benzopyrene and brominated pyrenes and fluoranthenes. Furthermore, the concentration of 1-chloropyrene in that air sample was estimated to be 10 pg/m³. XPAH were also found in snow samples taken in the vicinity of a motor-way. Ethylene dibromide and ethylene dichloride, are probably the source of the halogen atoms in the XPAH detected in car exhaust.     

Applicability of Fenton and H2O2/UV reactions in the treatment of tannery wastewaters

In this paper we evaluated the H2O2/UV and the Fenton's oxidation processes for the treatment of tannery wastewater under different experimental conditions. Efficiencies were judged by the amounts of organic substances degraded or eliminated under these treatment techniques. Daphnia magna and Vibrio fischeri were used to monitor toxicity. Organic compounds contained in the untreated and treated tannery wastewater were determined and identified using substance specific techniques. Gas chromatography-mass spectrometry (GC-MS) in positive electron impact (EI(+)) mode was applied to determine volatile organics. Atmospheric pressure ionization (API) mass (MS) and tandem mass spectrometry (MS-MS) coupled with flow injection analysis (FIA) or liquid chromatography (LC) were used to detect or identify polar organic pollutants. The experimental results indicated that both oxidation processes--H2O2/UV at pH 3 and Fenton at pH 3.5--are able to reduce TOC content by mineralisation of the organic compounds.     

Products and mechanisms of the gas-phase reactions of OH radicals and O3 with 2-methyl-3-buten-2-ol

Products of the gas-phase reactions of OH radicals (in the presence of NO) and O₃ with the biogenic organic compound 2-methyl-3-buten-2-ol have been investigated using gas chromatography with flame ionization detection (GC-FID), combined gas chromatography–mass spectrometry (GC-MS), gas chromatography with Fourier transform infrared detection (GC-FTIR), in situ FT-IR spectroscopy and in situ atmospheric pressure ionization tandem mass spectrometry (API-MS/MS). Formaldehyde, 2-hydroxy-2-methylpropanal and acetone were identified from both the OH radical and O₃ reactions, glycolaldehyde and organic nitrate (s) were also observed from the OH radical reaction, and the OH radical formation yield from the O₃ reaction was measured. The formaldehyde, 2-hydroxy-2-methylpropanal, glycolaldehyde, acetone and organic nitrate yields from the OH radical reaction were 0.29±0.03, 0.19±0.07, 0.61±0.09, 0.58±0.04 and 0.05±0.02, respectively, and the formaldehyde, 2-hydroxy-2-methylpropanal and OH radical formation yields from the O₃ reaction were 0.29±0.03, 0.30±0.06 (0.47 from FT-IR measurements) and 0.19 (uncertain to a factor of 1.5), respectively. Acetone was also observed from the O₃ reaction, but appeared to be formed from secondary reactions. Reaction mechanisms are presented and discussed.     

Thermal degradation products of spruce needles

Spruce needles are analysed by in-source pyrolysis (Py)-field ionization (FI) mass spectrography and Curie-point Py-gas chromatography/electron ionization mass spectrometry. The identified thermal degradation products allow the interpretation of the FI mass signals. It could be shown that Py-FI mass spectra of plant materials are representative fingerprints which consist primarily of molecular ions of Py products derived from the thermal degradation of the main constituents of spruce needles such as carbohydrates, lignin, lipids and proteins. Primary building blocks of these biopolymers form characteristic Py products of spruce needles. Furthermore, over 500 different molecular ion species of volatilized, thermostable plant constituents are recorded using FI as soft ionization method. The present study shows that Py-FIMS is suitable for the rapid and comprehensive characterization of complex biological materials, without pretreatment of the sample except of drying and milling. The presented results contribute to the basic knowledge for the evaluation of the causes of the present tree damage.     

Calculated physical properties of polychlorinated dibenzo-p-dioxins and dibenzofurans

The modified neglect of diatomic overlap (MNDO) method, a semi-empirical molecular orbital calculation, has been used to calculate the heats of formation, ionization potentials, dipole moments, and LUMOs (lowest unoccupied molecular orbitals) for all of the tetra, penta, hexa, hepta, and octa-chlorinated dibenzo-p-dioxins and dibenzofurans. These data have been used to predict gas chromatographic retention indexes.     

Evaluation of GC-ion trap-MS/MS methodology for monitoring PCDD/Fs in infant formulas

The application of high resolution gas chromatography in combination with low resolution mass spectrometry with electron ionization and MS/MS detection (HRGC-MS/MS) is tested for its use in the analysis of PCDD/Fs in infant formulas. Development of the analytical method was based upon EPA directrices and international recommendations. Calibration linearity was tested and average relative response for any native and labelled compound over the five-point calibration range below 14% was found. The precision and accuracy of the proposed analytical procedure are also presented. Results obtained are in agreement with EPA criteria. The method is applied to the analysis of a number of initial and follow-on milk based infant formulas. In general, HRGC-MS/MS constitutes an interesting method for the analysis of dioxins in such matrices.     

激光质谱法对机动车尾气中污染物的测量

本文详细介绍了一种全新的污染物测试方法———激光质谱法的原理和特点。我们应用这一方法对机动车尾气进行了初步探测 ,得到了 2 6 6nm激光作用下汽车尾气的激光电离质谱图 ,并对摩托车发动机运行状态与苯系列污染物排放量之间的关系进行了初步的在线测量     

Solid-state UV–MALDI–MS assay of transition metal dithiocarbamate fungicides

The determination of transition metal containing dithiocarbamate fungicides represents a challenging aspect of analytical object. They have a low stability, low solubility and stabilize versatile coordination monomers, dimers, disulfides and/or S-oxidized derivatives. Their diverse biological activities and agricultural implementation encompass plant prevention and crop protection against a variety of plants containing fungi and diseases of 400 pathogens and 70 cultures. Nonetheless, those dithiocarbamates (DTCs) are banned for agricultural use in Europe or have expiration at years 2016–2017 because of their highly toxic degradation products and/or metabolites, in particular ethylene thiourea; they found large-scale implementations in materials research and medicine. Despite the broad interdisciplinary of DTC application, due to the above reasons, they have received little attention in the rapidly growing field of analytical chemistry, and in particular, the analytical mass spectrometry. Therefore, the study reported on qualitative, quantitative and structural analysis of ten DTCs (1–10), using the matrix assisted laser desorption/ionization (UV–MALDI)–Orbitrap–mass spectrometry (MS) contributed considerably to the implementation of the method for environmental and foodstuffs monitoring. Its ultrahigh resolving power and capacity for direct solid-state analysis, at limited number of sample pretreatment steps, at concentration levels of analytes of up to femtogram per gram resulted to achievement of a highly precise analytical information for these non-trivial objects. The presented fully validated method and technique is based on the successful ionization of DTCs embedded in three novel organic salts (M₁–M₃). In this regard, the reported MS and the single-crystal X-ray diffraction data as well as the quantum chemical one are able to correlate the molecular structures in condense and in the gas phase. Despite the novelty of the fundamental methodological character of the research reported, the promising metrology contributed to the applied aspect of the UV–MALDI–MS as a robust analytical method for environmental and foodstuffs monitoring, which is tested on two commercially available crop protecting products such as Mancozeb® and Antracol®, respectively.     

A gas chromatography/high-resolution mass spectrometry (GC/HRMS) method for determination of polybrominated diphenyl ethers in fish

A method for the determination of polybrominated diphenyl ethers (PBDEs) in biota for routine analysis is described. The mass spectroscopic (MS) evaluation of 23 brominated diphenyl ethers, under electron ionization and electron capture negative ion conditions using magnetic sector and quadrupole mass spectrometers, showed that high-resolution mass spectrometry (HRMS) under electron ionization conditions was the most reliable technique, with high selectivity and adequate sensitivity. The instrument detection limit for this method ranged for individual congeners between 4.8 and 0.1 pg for 3-bromodiphenyl ether (BDE-2) and 2,3',4,4'-tetrabromodiphenyl ether (BDE-66), respectively, and method detection limit for each homologue group ranged between 5 pg/g for salmon certified reference material (CRM) and 93 pg/g for lake trout CRM. The effectiveness of this method was evaluated by analyzing the occurrence of PBDEs in commercially available CRMs comprising Lake Ontario lake trout, Pacific herring, and sockeye salmon. The average coefficients of variation for the replicate analyses of PDBEs in several tissue samples were: 25% for lake trout, 36% for Pacific herring, and 34% for sockeye salmon. The average deviations in the inter-laboratory study were: 14% for lake trout, 15% for Pacific herring, and 37% for sockeye salmon. Results indicated that the described method, based on gas chromatography/high-resolution mass spectrometry, is reliable for determining PBDE concentrations in biological tissues.     

Evaluation of non-enteric sources of non-methane volatile organic compound (NMVOC) emissions from dairies

Dairies are believed to be a major source of volatile organic compounds (VOC) in Central California, but few studies have characterized VOC emissions from these facilities. In this work, samples were collected from six sources of VOCs (Silage, Total Mixed Rations, Lagoons, Flushing Lanes, Open Lots and Bedding) at six dairies in Central California during 2006–2007 using emission isolation flux chambers and polished stainless steel canisters. Samples were analyzed by gas chromatography/mass spectrometry and gas chromatography/flame ionization detection. Forty-eight VOCs were identified and quantified in the samples, including alcohols, carbonyls, alkanes and aromatics. Silage and Total Mixed Rations are the dominant sources of VOCs tested, with ethanol as the major VOC present. Emissions from the remaining sources are two to three orders of magnitude smaller, with carbonyls and aromatics as the main components. The data suggest that animal feed rather than animal waste are the main source of non-enteric VOC emissions from dairies.