焦炭和废铁屑微电解预处理垃圾渗滤液的研究

研究表明,废铁屑和焦炭微电解是预处理垃圾渗滤液的一种有效方法,可去除垃圾渗滤液COD、色度和腐殖酸等污染物质,改善其可生化性、降低负荷,为后续生化处理创造良好的条件.通过静态正交实验确定废铁屑和焦炭最佳投加体积比为1∶3;最佳反应pH值为4;动态实验中,反应时间为1 h时,COD和色度去除率分别高达68%和91%;BOD/COD从0.3提高到0.5左右.     

高铁酸钾预处理垃圾渗滤液

采用自制高纯度高铁酸钾预处理危废填埋场和垃圾焚烧厂的垃圾渗滤液,探讨和分析了处理效果。正交实验表明,高铁酸钾预处理危废填埋场渗滤液COD的最佳条件为:高铁酸钾与COD的初始质量浓度比为0.5、渗滤液初始pH值4.00、反应温度30℃、反应时间40 min,此时COD去除率达71.51%。此最佳条件下高铁酸钾对不同类型垃圾渗滤液的色度、SS、COD、BOD5、氨氮、总磷、重金属离子等污染因子都具有良好的去除效果,危废填埋场渗滤液经高铁酸钾预处理后可以直接进入后续生化处理系统;垃圾焚烧厂渗滤液预处理后其COD为2 861.0 mg/L,经二次预处理也可进入生化处理系统。实验结果表明,高铁酸钾对不同类型垃圾渗滤液都具有良好的预处理效果。     

准好氧矿化垃圾反应床＋超声／芬顿联用技术处理垃圾渗滤液

针对垃圾渗滤液污染物浓度高、可生化性差等特点，采用准好氧矿化垃圾反应床＋超声／芬顿联用技术对垃圾渗滤液进行预处理。准好氧矿化垃圾床处理后渗滤液中COD、氨氮、总磷、色度的去除率分别为80％、85％、92％和85％。通过单因素实验和正交实验，确定了超声／Fenton法最佳工艺条件。经该组合工艺后，渗滤液中COD、氨氮、总磷和色度的最高去除率分别可达96％、86％、94％和95％，且出水无臭，颜色为淡黄色，BOD5／COD从0．16增至0．35左右，可生化性基本满足后续生物处理需要，且COD、总磷这2个指标达到《生活垃圾填埋场污染控制标准》（GB16889—2008）规定的排放标准。     

超声/Fenton联用技术处理垃圾渗滤液中的有机物

详细研究了超声/Fenton联用技术对垃圾渗滤液中有机物的处理效果.研究内容包括:超声波频率对垃圾渗滤液色度和COD去除率的影响,超声波功率对垃圾渗滤液色度和COD去除率的影响以及Fenton试剂用量和pH值对垃圾渗滤液色度去除率和COD去除率的影响.还利用一次正交回归实验确定了超声/Fenton联用技术处理垃圾渗滤液的优化条件,并在优化条件的基础上,对超声波技术、Fenton高级氧化技术和超声/Fenton联用技术对垃圾渗滤液的处理效果进行比较研究.研究结果表明:超声/Fenton联用技术对垃圾渗滤液的色度去除率和COD去除率最高,其色度去除率接近100%,COD去除率达到73.5%.超声/Fenton联用技术处理垃圾渗滤液的优化条件是:超声频率为28 kHz,超声功率为75W,Fe2 浓度为280 mg/L,H2O2浓度为1.29×104 mg/L,pH值为2.5.超声波的频率、功率和Fenton试剂用量之间存在优化匹配值.     

MFPAC混凝沉淀-矿化垃圾吸附预处理垃圾渗滤液

采用化学还原法制备纳米四氧化三铁,与聚合氯化铝(PAC)制备MFPAC磁性混凝剂,利用混凝沉淀-矿化垃圾吸附预处理垃圾渗滤液,用单因素变量法确定实验的最佳运行参数。结果表明:MFPAC磁性混凝剂对COD和色度的去除效果优于单独投加混凝剂PAC,在纳米四氧化三铁与PAC的质量比为1∶3、MFPAC的投加量为1.5 g·L~(-1)、搅拌条件为转速为300 r·min-1下搅拌60 s、溶液pH值为7.5(垃圾渗滤液原水的pH值)、絮凝时间为30 min的最佳运行条件下,COD由5 810 mg·L~(-1)降低到2 173 mg·L~(-1),色度由1 658倍降低到556倍,其COD去除率为62.6%,色度去除率为66.5%;利用矿化垃圾作为吸附剂处理MFPAC混凝处理后的出水,在矿化垃圾粒径小于2 mm、焙烧温度为700℃、吸附剂投加量为40 mg·L~(-1)、pH值为9的最佳条件下,经过12 h的处理,COD和氨氮的去除率分别为56.7%和68.4%,最终出水的COD和氨氮的浓度分别为941 mg·L~(-1)和343 mg·L~(-1);最终,MFPAC混凝沉淀-矿化垃圾吸附工艺对垃圾渗滤液COD、色度和氨氮的去除率分别为83.8%、78.5%和74.3%。     

硅藻土酸洗液-H2O2(Fenton)去除垃圾渗滤液色度及COD

垃圾渗滤液由于色度高、可生化性差,有时候需采用高级氧化技术（如Fenton法）处理。利用硅藻土酸洗改性产生的酸洗废水与30%H2O2制成Fenton试剂处理初始色度为800倍,COD浓度为810.4 mg/L的垃圾渗滤液。结果表明,当酸洗液与30%H2O2的体积比为6∶4,pH值为3.0,有紫外光照和搅拌的条件下,色度和COD的去除效率最好,分别达到了96.25%和74.14%;且产生的污泥量（干重）最少。     

臭氧化对垃圾填埋场后期渗滤液的预处理研究

应用自制微孔扩散式接触反应器,考察了不同pH条件下垃圾填埋场后期渗滤液的臭氧化预处理效果.结果表明,渗滤液初始pH值升高,臭氧利用率增大,垃圾渗滤液中COD、腐殖酸的去除速率加快;当初始pH为10时,经臭氧化处理120 min后,模拟废水的BOD5/COD可从初始的0.17提高到0.36,改善了废水的可生化性,同时渗滤液的色度、浊度、腐殖酸和SS也有较高的去除率.     

基于新型絮凝剂和专用絮凝反应器的垃圾渗滤液处理中试研究

针对实验室所得垃圾渗滤液专用铁镁铝复合絮凝剂配方进行了批量扩大化生产,设计开发了中试专用絮凝反应设备,在垃圾填埋现场进行了絮凝中试实验。研究结果表明,最佳搅拌速度为170 r/min,最佳投药量为20%,COD去除率大于50%,BOD去除率大于30%,渗滤液可生化性由0.4提高到0.65,色度去除率约70%～80%,重金属去除率大于80%,优于同类常规市售絮凝剂聚铁、聚铝、聚铝铁;垃圾渗滤液处理专用絮凝反应器能满足设计开发要求,具有处理效果好、结构紧凑、多功能、自动化程度高、方便移动适于现场实验等特点;为适应渗滤液絮凝反应剧烈、产生大量泡沫、影响固液分离效果的特点,专用絮凝反应器固液分离部分的细部尺寸应进一步优化调整。     

光电芬顿氧化法深度处理垃圾渗滤液研究

采用光电芬顿氧化法对北京市某垃圾填埋场已经生化处理后的垃圾渗滤液进行深度处理，分别考察了电流强度和铁的不同价态等因素对渗滤液总有机碳（TOC）、化学需氧量（COD）以及色度去除效果的影响，并对阳极氧化、电芬顿和光电芬顿不同反应过程进行了对比。通过分析渗滤液UV-Vis光谱(200～500 nm)变化和渗滤液中有机污染物的分子量变化，发现光电芬顿反应可以明显改善渗滤液生化性。深入研究了反应过程中铁价态的变化规律。试验结果发现，以高比表面积的活性炭纤维(ACF)为阴极的光电芬顿反应可以有效降解垃圾渗滤液，在pH为3，Fe²⁺ 浓度为1 mmol/L，电流为0.5 A，O₂通入量为250 mL/min条件下降解360 min，垃圾渗滤液TOC和COD去除率分别达到78.9%和62.8%，色度完全去除。     

H2O2协同O3预处理垃圾填埋场后期渗滤液的研究

应用自制微孔扩散式接触反应器,考察了H2O3/O3在不同摩尔比下对垃圾填埋场后期渗滤液的氧化处理效果.结果表明,H2O3/O3的摩尔比对处理效果有明显的影响.在试验范围内,确定H2O3/O3的最佳摩尔比为0.2:1,最佳处理时间为90 min,经过H2O3/O3处理后,垃圾填埋场后期渗滤液的BOD5/COD可从初始的0.17提高到0.36,改善了废水的可生化性,同时渗滤液的色度、浊度、腐殖酸和SS也有较高的去除率.     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染     

活性炭三维电极法对印染废水的处理研究

对三维电极方法处理印染废水进行了实验研究,初步探讨了活性炭三维电极法处理印染废水的机理,对影响处理效果的各种要素,如反应时间、槽电压和pH值等进行了条件实验,得出了活性炭三维电极法处理印染废水的最佳运行条件为:停留时间120-180 min,槽电压25～30 V,进水pH值6.5～7.5。结果表明,该反应器能有效地降低废水色度,有较高的COD去除效率,并能提高印染废水的可生化性。     

红土吸附砷对其动电电位的影响

研究了遵义红土吸附砷对其动电电位的影响 ,从砷酸根浓度和体系pH对红土动电电位影响的角度作了探讨 ,结果表明 ,砷酸根离子浓度越大 ,Zata电位下降幅度越大 ,Zata电位也越低 ;随着体系pH的升高 ,氧化铁胶体动电电位逐渐下降 ,甚至改变了表面电位的符号。由此得出了红土吸附砷属于专性吸附的结论。     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

Visualisation of the complexity of EUSES

The interdependencies of parameters applied in the models of EUSES are visualised in a directed connectivity graph. The parameters (inputs, defaults, state variables, outputs) are represented by boxes (nodes) and their relations by lines (edges). The visualisation, on the one hand, clarifies the complexity of the models in EUSES and, on the other hand, creates an overview and transparency. The parameters’ relations to each other can be recognised faster, and the models can be better understood. The complexity was quantified by the number (variety), kind (substance parameter, physico-chemical parameter, concentration, other parameters), and depth (dimension) of the parameter and the number of relations (connectivity). The variety of EUSES (without the modelsSimple Treat andSimple Box whose interior structure is not documented and without the effect and risk characterisation) amounts to 466, the connectivity to 961, and the maximal dimension is 21.