Transformation and removal of ammonium sulfate aerosols and ammonia slip from selective catalytic reduction in wet flue gas desulfurization system

Selective catalytic reduction (SCR) denitration may increase the emission of NH₄⁺ and NH₃. The removal and transformation characteristics of ammonium sulfate aerosols and ammonia slip during the wet flue gas desulfurization (WFGD) process, as well as the effect of desulfurization parameters, were investigated in an experimental system equipped with a simulated SCR flue gas generation system and a limestone-based WFGD system. The results indicate that the ammonium sulfate aerosols and ammonia slip in the flue gas from SCR can be partly removed by slurry scrubbing, while the entrainment and evaporation of desulfurization slurry with accumulated NH₄⁺ will generate new ammonium-containing particles and gaseous ammonia. The ammonium-containing particles formed by desulfurization are not only derived from the entrainment of slurry droplets, but also from the re-condensation of gaseous ammonia generated by slurry evaporation. Therefore, even if the concentration of NH₄⁺ in the desulfurization slurry is quite low, a high level of NH₄⁺ was still contained in the fine particles at the outlet of the scrubber. When the accumulated NH₄⁺ in the desulfurization slurry was high enough, the WFGD system promoted the conversion of NH₃ to NH₄⁺ and increased the additional emission of primary NH₄⁺ aerosols. With the decline of the liquid/gas ratio and flue gas temperature, the removal efficiency of ammonia sulfate aerosols increased, and the NH₄⁺ emitted from entrainment and evaporation of the desulfurization slurry decreased. In addition, the volatile ammonia concentration after the WFGD system was reduced with the decrease of the NH₄⁺ concentration and pH values of the slurry.     

The biological effect of metal ions on the granulation of aerobic granular activated sludge

As a special biofilm structure, microbial attachment is believed to play an important role in the granulation of aerobic granular activated sludge (AGAS). This experiment was to investigate the biological effect of Ca^2 +, Mg^2 +, Cu^2 +, Fe^2 +, Zn^2 +, and K⁺ which are the most common ions present in biological wastewater treatment systems, on the microbial attachment of AGAS and flocculent activated sludge (FAS), from which AGAS is always derived, in order to provide a new strategy for the rapid cultivation and stability control of AGAS. The result showed that attachment biomass of AGAS was about 300% higher than that of FAS without the addition of metal ions. Different metal ions had different effects on the process of microbial attachment. FAS and AGAS reacted differently to the metal ions as well, and in fact, AGAS was more sensitive to the metal ions. Specifically, Ca^2 +, Mg^2 +, and K⁺ could increase the microbial attachment ability of both AGAS and FAS under appropriate concentrations, Cu^2 +, Fe^2 +, and Zn^2 + were also beneficial to the microbial attachment of FAS at low concentrations, but Cu^2 +, Fe^2 +, and Zn^2 + greatly inhibited the attachment process of AGAS even at extremely low concentrations. In addition, the acylated homoserine lactone (AHL)-based quorum sensing system, the content of extracellular polymeric substances and the relative hydrophobicity of the sludges were greatly influenced by metal ions. As all these parameters had close relationships with the microbial attachment process, the microbial attachment may be affected by changes of these parameters.     

湿法脱硫浆液中石膏与汞的结合特性模拟研究

燃煤烟气湿法脱硫石膏中汞的大量富集限制了其应用范围且容易产生汞的二次逃逸问题.因此,本文对脱硫浆液中的汞在固相石膏的迁移转化规律进行了模拟研究,考察了不同操作条件和离子浓度的影响,探求汞进入石膏的量和形态的变化趋势.同时考察了温度、p H、石膏老化时间和结晶方式等对汞与石膏结合特性的影响,并对机理进行了探讨.结果表明,当液相汞浓度从0.16 mg·L-1增加到2.67 mg·L-1时,进入石膏的汞含量相应从0.38 mg·kg-1增加到4.17 mg·kg-1,但其占液相总汞的比例却呈先下降后不变的趋势.当石膏浆液浓度从1%增加到20%时,由液相进入石膏中的汞比例不断上升,但石膏汞含量却不断下降.基于实验结果推测汞与石膏结合的两种方式:石膏的内部包裹作用和石膏的表面吸附作用.另外,酸根离子浓度会改变浆液中游离汞的含量,从而影响石膏中汞的富集量:Cl-和NO-3对汞进入石膏有抑制作用,而SO2-4的存在会起到促进作用;铁、铝阳离子的存在会促进汞进入石膏,钙、镁阳离子对汞的富集基本无影响.     

白泥烟气脱硫技术与燃煤电厂工程应用

系统地考察了白泥的物化特性、白泥脱硫浆液的特性,并对w（白泥浆液）、pH等因素对脱硫性能的影响进行了研究.在国电肇庆热电有限公司2×350 MW超临界锅炉机组上开展了工程化应用研究,对比研究了白泥脱硫与传统石灰石-石膏法脱硫的性能与石膏副产物特性.结果表明:w（白泥浆液）和pH对脱硫效率影响较为明显,w（白泥浆液）低于12.5%的条件（5.0%、8.0%）下,pH由10.0减至6.0时,脱硫效率逐渐减小;w（白泥浆液）为12.5%的条件下,pH对脱硫效率的影响基本可以忽略;在三层浆液喷淋填料塔内,液气比为8 L/m3,空塔气速为0.4 m/s,脱硫效率最高可达96.7%以上.350 MW燃煤电厂白泥脱硫工程应用结果表明,采用单塔双循环工艺,在运行负荷为240~249 MW范围内,ρ（SO₂）为1 948~1 999 mg/m3的条件下,白泥脱硫的效率（99.25%~99.49%）优于石灰石-石膏法（99.18%~99.20%）;白泥作为脱硫剂时,烟气出口ρ（SO₂）最低仅为10 mg/m3,可满足超低排放标准对SO₂控制的要求.研究显示,与石灰石-石膏法生成的石膏副产物相比,白泥脱硫石膏在酸不溶物、含水率等指标及外观方面基本接近,符合建材制品要求,满足副产物资源化要求.      

Kinetics and mechanism of hexavalent chromium removal by basic oxygen furnace slag

Basic oxygen furnace slag(BOFS) has the potential to remove hexavalent chromium(Cr(VI))from wastewater by a redox process due to the presence of minerals containing Fe2+. The effects of the solution p H, initial Cr(VI) concentration, BOFS dosage, BOFS particle size, and temperature on the removal of Cr(VI) was investigated in detail through batch tests. The chemical and mineral compositions of fresh and reacted BOFS were characterized using scanning electron microscope(SEM) equipped with an energy dispersive spectrometer(EDS)system and X-ray diffractometer(XRD). The results show that Cr(VI) in wastewater can be efficiently removed by Fe2+released from BOFS under appropriate acidic conditions. The removal of Cr(VI) by BOFS significantly depended on the parameters mentioned above. The reaction of Cr(VI) with BOFS followed the pseudo-second-order kinetic model. Fe2+responsible for Cr(VI) removal was primarily derived from the dissolution of Fe O and Fe3O4 in BOFS. When H2SO4 was used to adjust the solution acidity, gypsum(Ca SO4·2H2O)could be formed and become an armoring precipitate layer on the BOFS surface, hindering the release of Fe2+and the removal of Cr(VI). Finally, the main mechanism of Cr(VI) removal by BOFS was described using several consecutive reaction steps.     

Removal of Cs from water and soil by ammonium-pillared montmorillonite/Fe3O4 composite

To remove cesium ions from water and soil, a novel adsorbent was synthesized by following a one-step co-precipitation method and using non-toxic raw materials. By combining ammonium-pillared montmorillonite (MMT) and magnetic nanoparticles (Fe₃O₄), an MMT/Fe₃O₄ composite was prepared and characterized. The adsorbent exhibited high selectivity of Cs⁺ and could be rapidly separated from the mixed solution under an external magnetic field. Above all, the adsorbent had high removal efficiency in cesium-contaminated samples (water and soil) and also showed good recycling performance, indicating that the MMT/Fe₃O₄ composite could be widely applied to the remediation of cesium-contaminated environments. It was observed that the pH, solid/liquid ratio and initial concentration affected adsorption capacity. In the presence of coexisting ions, the adsorption capacity decreased in the order of Ca^2 + > Mg^2 + > K⁺ > Na⁺, which is consistent with our theoretical prediction. The adsorption behavior of this new adsorbent could be expressed by the pseudo-second-order model and Freundlich isotherm. In addition, the adsorption mechanism of Cs⁺ was NH₄⁺ ion exchange and surface hydroxyl group coordination, with the former being more predominant.     

New insight into adsorption characteristics and mechanisms of the biosorbent from waste activated sludge for heavy metals

The adsorption characteristics and mechanisms of the biosorbent from waste activated sludge were investigated by adsorbing Pb2+and Zn2+in aqueous single-metal solutions. A p H value of the metal solutions at 6.0 was beneficial to the high adsorption quantity of the biosorbent. The optimal mass ratio of the biosorbent to metal ions was found to be 2. A higher adsorption quantity of the biosorbent was achieved by keeping the reaction temperature below 55°C. Response surface methodology was applied to optimize the biosorption processes, and the developed mathematical equations showed high determination coefficients(above 0.99 for both metal ions) and insignificant lack of fit(p = 0.0838 and 0.0782 for Pb2+and Zn2+, respectively). Atomic force microscopy analyses suggested that the metal elements were adsorbed onto the biosorbent surface via electrostatic interaction. X-ray photoelectron spectroscopy analyses indicated the presence of complexation(between –NH2,-CN and metal ions) and ion-exchange(between –COOH and metal ions). The adsorption mechanisms could be the combined action of electrostatic interaction, complexation and ion-exchange between functional groups and metal ions.     

Cu(II), Fe(III) and Mn(II) combinations as environmental stress factors have distinguishing effects on Enterococcus hirae

Pollution by various heavy metals as environmental stress factors might affect bacteria. It was established that iron (Fe(III)), manganese (Mn(II)) and copper (Cu(II)) ion combinations caused effects on Enterococcus hirae that differed from the sum of the effects when the metals were added separately. It was shown that the Cu^2 +–Fe^3 + combination decreased the growth and ATPase activity of membrane vesicles of wild-type E. hirae ATCC9790 and atpD mutant (with defective F_oF₁-ATPase) MS116. Addition of Mn^2 +–Fe^3 + combinations within the same concentration range had no effects on growth compared to control (without heavy metals). ATPase activity was increased in the presence of Mn^2 +–Fe^3 +, while together with 0.2 mmol/L N,N′-dicyclohexylcarbodiimide (DCCD), ATPase activity was decreased compared to control (when only 0.2 mmol/L DCCD was present). These results indicate that heavy metals ion combinations probably affect the F_OF₁-ATPase, leading to conformational changes. Moreover the action may be direct or be mediated by environment redox potential. The effects observed when Fe^3 + was added separately disappeared in both cases, which might be a result of competing processes between Fe^3 + and other heavy metals. These findings are novel and improve the understanding of heavy metals ions effects on bacteria, and could be applied for regulation of stress response patterns in the environment.     

动态沉降分离电石渣脱硫浆液中黑色悬浮物质的实验研究

电石渣脱硫浆液中存在沉降速率低于二水硫酸钙的黑色悬浮物质,严重影响脱硫石膏真空过滤,在浆液沉降装置中,对动态沉降分离电石渣脱硫浆液中的黑色悬浮物质进行了实验研究,研究表明:搅拌转速在30～70 r/min,可实现电石渣脱硫浆液动态沉降分层,搅拌转速为60 r/min时,浆液分层最佳;虹吸分离上层黑色悬浮液,黑色物质去除率可达到70%,在相同的过滤工艺条件下,浆液过滤后滤饼含水率可降低3%～5%;浆液中黑色物质含量低于3 g/L时,进一步降低浆液中黑色物质的含量,对提高浆液脱水性能作用不大,甚至可以忽略不计。     

湿式石灰石-石膏烟气脱硫系统的工艺控制

通过实践提出湿法脱硫系统运行时工艺参数的优化值,重点讨论了浆液pH、石膏相对过饱和度的控制,以实例说明烟气负荷变化时设备运行方式的改变和参数的调整手段。     

Characteristics of mass distributions of aerosol particle and its inorganic water-soluble ions in summer over a suburb farmland in Beijing

Agricultural activity is one of the most important sources of aerosol particles. To understand the mass distribution and sources of aerosol particles and their inorganic water-soluble ions in a suburb farmland of Beijing, particle samples were collected using a microorifice uniform deposit impactor (MOUDI) in the summer of 2004 in a suburb vegetable field. The distribution of the particles and their inorganic water-soluble ions in the diameter range of 0.18–18 μm were measured. The dominant fine particle ions were SO₄ ²⁻, NO₃ ⁻, and NH₄ ⁺. The association of day-to-day variation of the concentration of these ions with temperature, humidity, and solar radiation suggested that they are formed by the reaction of NH₃ released from the vegetable field with the acid species produced from photochemical reactions. Fine particle K⁺ is likely from vegetation emission and biomass burning. Coarse particles like Ca²⁺, Mg²⁺, NO₃ ⁻, and SO₄ ²⁻ are suggested to come from the mechanical process by which the soil particle entered the atmosphere, and from the reaction of the acid species at the surface of the soil particle. The results show that fertilizer and soil are important factors determining the aerosol particle over agricultural fields, and vegetable fields in suburban Beijing contribute significantly to the aerosol particle. Translated from Environmental Science, 2006, 27(2): 193–199 [译自: 环境科学]     

Chemical characterization of size-resolved aerosols in four seasons and hazy days in the megacity Beijing of China

Size-resolved aerosol samples were collected by MOUDI in four seasons in 2007 in Beijing. The PM₁₀ and PM_1.8 mass concentrations were 166.0 ± 120.5 and 91.6 ± 69.7 μg/m³, respectively, throughout the measurement, with seasonal variation: nearly two times higher in autumn than in summer and spring. Serious fine particle pollution occurred in winter with the PM_1.8/PM₁₀ ratio of 0.63, which was higher than other seasons. The size distribution of PM showed obvious seasonal and diurnal variation, with a smaller fine mode peak in spring and in the daytime. OM (organic matter = 1.6 × OC (organic carbon)) and SIA (secondary inorganic aerosol) were major components of fine particles, while OM, SIA and Ca^2 + were major components in coarse particles. Moreover, secondary components, mainly SOA (secondary organic aerosol) and SIA, accounted for 46%–96% of each size bin in fine particles, which meant that secondary pollution existed all year. Sulfates and nitrates, primarily in the form of (NH₄)₂SO₄, NH₄NO₃, CaSO₄, Na₂SO₄ and K₂SO₄, calculated by the model ISORROPIA II, were major components of the solid phase in fine particles. The PM concentration and size distribution were similar in the four seasons on non-haze days, while large differences occurred on haze days, which indicated seasonal variation of PM concentration and size distribution were dominated by haze days. The SIA concentrations and fractions of nearly all size bins were higher on haze days than on non-haze days, which was attributed to heterogeneous aqueous reactions on haze days in the four seasons.     

Remediation of saline–sodic soil with flue gas desulfurization gypsum in a reclaimed tidal flat of southeast China

Salinization and sodicity are obstacles for vegetation reconstruction of coastal tidal flat soils. A study was conducted with flue gas desulfurization(FGD)-gypsum applied at rates of 0, 15, 30, 45 and 60 Mg/ha to remediate tidal flat soils of the Yangtze River estuary.Exchangeable sodium percentage(ESP), exchangeable sodium(ExNa), p H, soluble salt concentration, and composition of soluble salts were measured in 10 cm increments from the surface to 30 cm depth after 6 and 18 months. The results indicated that the effect of FGD-gypsum is greatest in the 0–10 cm mixing soil layer and 60 Mg/ha was the optimal rate that can reduce the ESP to below 6% and decrease soil p H to neutral(7.0). The improvement effect was reached after 6 months, and remained after 18 months. The composition of soluble salts was transformed from sodic salt ions mainly containing Na~+, HCO_3~-+ CO_3~(2-)and Cl-to neutral salt ions mainly containing Ca~(2+)and SO_4~(2-). Non-halophyte plants were survived at 90%. The study demonstrates that the use of FGD-gypsum for remediating tidal flat soils is promising.     

Dynamic nano-Ag colloids cytotoxicity to and accumulation by Escherichia coli: Effects of Fe3+, ionic strength and humic acid

Released Ag ions or/and Ag particles are believed to contribute to the cytotoxicity of Ag nanomaterials, and thus, the cytotoxicity and mechanism of Ag nanomaterials should be dynamic in water due to unfixed Ag particle:Ag⁺ ratios. Our recent research found that the cytotoxicity of PVP-Ag nanoparticles is attributable to Ag particles alone in 3 hr bioassays, and shifts to both Ag particles and released Ag⁺ in 48 hr bioassays. Herein, as a continued study, the cytotoxicity and accumulation of 50 and 100 nm Ag colloids in Escherichia coli were determined dynamically. The cytotoxicity and mechanisms of nano-Ag colloids are dynamic throughout exposure and are derived from both Ag ions and particles. Ag accumulation by E. coli is derived mainly from extracellular Ag particles during the initial 12 hr of exposure, and thereafter mainly from intracellular Ag ions. Fe³⁺ accelerates the oxidative dissolution of nano-Ag colloids, which results in decreasing amounts of Ag particles and particle-related toxicity. Na⁺ stabilizes nano-Ag colloids, thereby decreasing the bioavailability of Ag particles and particle-related toxicity. Humic acid (HA) binds Ag⁺ to form Ag⁺-HA, decreasing ion-related toxicity and binding to the E. coli surface, decreasing particle-related toxicity. HA in complex conditions showed a stronger relative contribution to toxicity and accumulation than Na⁺ or Fe³⁺. The results highlighted the cytotoxicity and mechanism of nano-Ag colloids are dynamic and affected by environmental factors, and therefore exposure duration and water chemistry should be seriously considered in environmental and health risk assessments.     

Effect of organic matter on phosphorus recovery from sewage sludge subjected to microwave hybrid pretreatment

Microwave (MW) hybrid processes are able to disrupt the flocculent structure of complex waste activated sludge, and help promote the recovery of phosphorus as struvite. In this study, to optimize struvite yield, (1) the characteristics of matter released in MW-hybrid treatments were compared, including MW, MW-acid, MW-alkali, MW-H₂O₂, and MW-H₂O₂-alkali. The results showed that selective release of carbon, nitrogen, phosphorus, Ca^2 +, and Mg^2 + achieved by sludge pretreatment using MW-hybrid processes. MW-H₂O₂ is the recommended sludge pretreatment process for phosphorus recovery in the form of struvite. The ratio of Mg^2 +:NH₄⁺-N:PO₄^3 −-P was 1.2:2.9:1 in the supernatant. (2) To clarify the effects of organic matter on struvite recovery, the composition and molecular weight distribution of organic matters were analyzed. Low molecular weight COD was found to facilitate the removal rate of NH₄⁺-N and PO₄³-P via crystallization, and the amorphous struvite crystals (< 1 kDa) from the filtered solutions had high purity. Therefore, the present study reveals the necessity of taking into consideration the interference effect of high molecular weight organic matters during struvite crystallization from sewage sludge.     

Insight into the adsorption of tetracycline onto amino and amino–Fe functionalized mesoporous silica: Effect of functionalized groups

In order to study the influences of functionalized groups onto the adsorption of tetracycline (TC), we prepared a series of amino and amino–Fe^3 + complex mesoporous silica adsorbents with diverse content of amino and Fe^3 + groups (named N,N-SBA15 and Fe-N,N-SBA15). The resulting mesoporous silica adsorbents were fully characterized by X-ray powder diffraction, Fourier transform infrared spectrometer and N₂ adsorption/desorption isotherms. Furthermore, the effects of functionalized groups on the removal of TC were investigated. The results showed that the periodic ordered structure of SBA-15 was maintained after modification of amino/Fe^3 + groups. The functionalized amino groups decreased the adsorption capacity while the coordinated Fe^3 + increased the adsorption capacity. The adsorption kinetics of TC fitted pseudo-second-order model well and the equilibrium was achieved quickly. The adsorption isotherms fitted the Langmuir model well and with the Fe^3 + content increased from 3.93% to 8.26%, the Q_max of the adsorbents increased from 102 to 188 mmol/kg. The solution pH affected the adsorption of TC onto amino complex adsorbents slightly while influenced the adsorption onto Fe-amine complex adsorbents greatly. The adsorption of TC on SBA15 and N,N-SBA15 may be related to the formation of outer-sphere surface complexes, while the adsorption of TC onto Fe-N,N-SBA15 was mainly attributed to the inner-sphere surface complexes. This study could offer potential materials that have excellent adsorption behavior for environmental remediation and suggested useful information for the preparing other adsorbents in environmental applications.     

Effects of metal ions on the catalytic degradation of dicofol by cellulase

A new technique whereby cellulase immobilized on aminated silica was applied to catalyze the degradation of dicofol, an organochlorine pesticide. In order to evaluate the performance of free and immobilized cellulase, experiments were carried out to measure the degradation efficiency. The Michaelis constant, K_m, of the reaction catalyzed by immobilized cellulase was 9.16 mg/L, and the maximum reaction rate, V_max, was 0.40 mg/L/min, while that of free cellulase was K_m = 8.18 mg/L, and V_max = 0.79 mg/L/min, respectively. The kinetic constants of catalytic degradation were calculated to estimate substrate affinity. Considering that metal ions may affect enzyme activity, the effects of different metal ions on the catalytic degradation efficiency were explored. The results showed that the substrate affinity decreased after immobilization. Monovalent metal ions had no effect on the reaction, while divalent metal ions had either positive or inhibitory effects, including activation by Mn^2 +, reversible competition with Cd^2 +, and irreversible inhibition by Pb^2 +. Ca^2 + promoted the catalytic degradation of dicofol at low concentrations, but inhibited it at high concentrations. Compared with free cellulase, immobilized cellulase was affected less by metal ions. This work provided a basis for further studies on the co-occurrence of endocrine-disrupting chemicals and heavy metal ions in the environment.     

碳酸盐体系中pH对Cu2+诱导结晶过程的影响

在流化床中,以含Cu2+废水为处理对象,考察了碳酸盐体系中pH的改变对Cu2+诱导结晶过程的影响. 结果表明:当进水ρ(Cu2+)为200 mg/L、沉淀剂pH为10.2时,经回流系统拦截,微晶产率可降低0.5%~1.0%,Cu2+的去除率可达99.0%以上. 经XRD(X射线衍射)分析表明,结晶产物以碱式碳酸铜为主,晶型呈短杆状,尺寸较为均一;当沉淀剂pH升至12.2时,Cu2+的去除率降至95.0%,系统出水结晶产物晶型特征不明显,尺寸不均,XRD结果显示为氢氧化铜、碱式碳酸铜、碳酸钙等混合结晶产物,晶体衍射峰多存在宽化现象,表明高pH下结晶产物晶化程度较低.      

Effect of calcium formate as an additive on desulfurization in power plants

SO_2 in flue gas needs to be eliminated to alleviate air pollution. As the quality of coal decreases and environmental standard requirements become more stringent, the highefficiency desulfurization of flue gas faces more and more challenges. As an economical and environmentally friendly solution, the effect of calcium formate as an additive on desulfurization efficiency in the wet flue gas desulfurization(WFGD) process was studied for the first time. Improvement of the desulfurization efficiency was achieved with limited change in p H after calcium formate was added into the reactor, and it was found to work better than other additives tested. The positive effects were further verified in a power plant, which showed that adding calcium formate could promote the dissolution of calcium carbonate, accelerate the growth of gypsum crystals and improve the efficiency of desulfurization. Thus, calcium formate was proved to be an effective additive and can potentially be used to reduce the amount of limestone slurry required, as well as the energy consumption and operating costs in industrial desulfurization.     

Biodegradation of pendimethalin by Bacillus subtilis Y3

A bacterium strain Y3,capable of efficiently degrading pendimethalin,was isolated from activated sludge and identified as Bacillus subtilis according to its phenotypic features and 16 S rRNA phylogenetic analysis.This strain could grow on pendimethalin as a sole carbon source and degrade 99.5%of 100 mg/L pendimethalin within 2.5 days in batch liquid culture,demonstrating a greater efficiency than any other reported strains.Three metabolic products,6-aminopendimethalin,5-amino-2-methyl-3-nitroso-4-(pentan-3-ylamino) benzoic acid,and 8-amino-2-ethyl-5-(hydroxymethyl)-1,2-dihydroquinoxaline-6-carboxylic acid,were identified by HPLC-MS/MS,and a new microbial degradation pathway was proposed.A nitroreductase catalyzing nitroreduction of pendimethalin to 6-aminopendimethalin was detected in the cell lysate of strain Y3.The cofactor was nicotinamide adenine dinucleotide phosphate(NADPH) or more preferably nicotinamide adenine dinucleotide(NADH).The optimal temperature and pH for the nitroreductase were 30℃ and 7.5,respectively.Hg~(2+),Ni~(2+),Pb~(2+),Co~(2+),Mn~(2+) Cu~(2+),Ag~+,and EDTA severely inhibited the nitroreductase activity,whereas Fe~(2+),Mg~(2+),and Ca~(2+) enhanced it.This study provides an efficient pendimethalin-degrading microorganism and broadens the knowledge of the microbial degradation pathway of pendimethalin.