Effect of dissolved metal ions on PCE decomposition by gamma-rays

This study investigates the effect of initial tetrachloroethylene (PCE) concentration, irradiation dose and dissolved metal ions such as Cr3+, Mn2+, Fe3+, Co2+, Ni2+, Cu2+ and Zn2+ on removal of PCE by gamma irradiation. The amount of removed PCE decreased with increase in initial PCE concentration and increased with increase in irradiation dose. PCE removal reached a maximum in the presence of Fe3+, while Cu2+ strongly hindered PCE decomposition. Except for Cu2+, the amount of removed PCE in the presence of metal ions was linearly dependent on the standard reduction potential of the metal ions. The extraordinary inhibition of Cu2+ in PCE removal was caused by the action of Cu2+ as a strong *OH scavenger, that was directly confirmed by electron paramagnetic resonance spectroscopy.     

可渗透反应复合电极法对土壤重金属的电动去除

将零价铁(Fe0)、沸石等活性材料附着在电极上形成可渗透反应层并构成可渗透反应复合电极,采用不同的复合电极对Cd2+、Ni 2+、Pb2+和Cu2+等4种阳离子型重金属污染土壤进行了电动力学修复。研究了不同可渗透反应复合电极对土壤pH的控制效果以及对重金属的去除作用,分析了迁移到复合电极中的重金属形态变化。结果表明,复合电极中添加酸、碱性沸石并适时更换,可有效中和、截留阴阳极电解产生的OH-和H+,避免或减缓土壤酸碱迁移带的形成,防止重金属离子的过早沉淀及土壤过度酸化,极大提高了重金属的去除率。复合电极中Fe0可将迁移进来的重金属离子进行还原稳定,实现重金属污染物的捕获与固定,与迁移到沸石复合电极中的4种重金属不稳定态相比,"Fe0+沸石"复合电极中重金属不稳定态分别下降了61.4、60.5、61.4、57.1百分点。结果还显示,阴极采用"Fe0+沸石"复合电极并适时进行更换,施加1.5V/cm的直流电压修复10d后,土壤中Cd、Ni、Pb、Cu的总去除率分别为44.5%、41.5%、33.5%和36.7%,且进一步延长修复时间和持续更换电极可获得更为理想的修复效果。     

Evaluation of pectin binding of heavy metal ions in aqueous solutions

Evaluation of adsorption performance of several industrially manufactured pectins towards some toxic heavy metals was carried out. Adsorption isotherms for divalent cations in simulant aqueous solutions were measured and corresponding distribution coefficients were calculated. The following selectivity sequences we found for pectins: Pb2+ > Cu2+ > Co2+ > Ni2+ > Zn2+ > Cd2+. It was shown that a beet pectin exhibits a high affinity for Pb2+ and Cu2+ ions, an apple pectin for Co2+ ion and a citrus pectin for Ni2+ ion. The binding properties of all pectins towards Zn2+ and Cd2+ ions are extremely poor. The quantitative data on adsorption performance of pectins suggest their applicability as food additives or remedies for efficient removal of Pb2+, Cu2+, Co2+, and Ni2+ ions from different biological systems, including human and animal organisms.     

Utilization of Modified Attapulgite for the Removal of Sr(II), Co(II), and Ni(II) Ions from Multicomponent System,Part I: Kinetic Studies

Radionuclide sorption by natural and modified clays is extensively accepted to be an important process from the radioactive waste point of view. This work focused on modification of natural attapulgite with a layered double hydroxide to produce a novel chemisorbent for Sr2+, Ni2+, and Co2+ removal from multicomponent solution. The structural and surface characteristics of both attapulgite (ATP) and modified attapulgite (LDH-ATP) were investigated using XRD, FTIR, SEM, and thermal analysis. Comparison of sorption features of Sr2+, Ni2+, and Co2+ onto ATP and LDH-ATP was achieved; the results indicated that LDH-ATP was the most efficient sorbent for Sr2+, Ni2+, and Co2+. Kinetic studies established that the sorption is fast and reaching >90% within 30 min. The sorption of Sr2+, Ni2+, and Co2+ are well defined by non-linear pseudo-second-order model and controlled by an intra-particle diffusion mechanism. The diffusivity was determined using homogeneous surface diffusion (HSDM) model and found in the order 10−13 m2/min; this confirmed that the sorption of the three ions is chemisorption process. LDH-ATP can be employed as a candidate chemisorbent for the removal of some metal ions from waste solution.     

Competitive adsorption characteristics of Co2+, Ni2+, and Cr3+ by IRN-77 cation exchange resin in synthesized wastewater

Adsorption properties of Co2+, Ni2+, and Cr3+ on an Amberlite IRN-77 cation exchange resin were investigated in batch systems. Levels of adsorption rapidly approached an equilibrium state within 1 h. The adsorption characteristics of each metal onto the resin were accurately represented by Langmuir isotherms. Co2+ and Ni2+, which have an equivalent electrovalence, displayed similar levels of adsorption onto the resin when they coexisted in the solution. However, when Cr3+ was added to the solution it competitively replaced Co2+ and Ni2+ ions that had been previously adsorbed onto the resin, resulting in the desorption of these metals into the solution. The result was likely due to a higher adsorption affinity of Cr3+ relative to Co2+ and Ni2+. This implies that interactively competitive adsorption of multi-cations onto the resin should be thoroughly considered when contemplating the efficient operation of an ion exchange process in the treatment of industrial wastewater.     

Simultaneous heavy metal removal mechanism by dead macrophytes

The use of dead, dried aquatic plants, for water removal of metals derived from industrial activities as a simple biosorbent material has been increasing in the last years. The mechanism of simultaneous metal removal (Cd2+, Ni2+, Cu2+, Zn2+ and Pb2+) by 3 macrophytes biomass (Spirodela intermedia, Lemna minor and Pistia stratiotes) was investigated. L. minor biomass presented the highest mean removal percentage and P. stratiotes the lowest for all metals tested. Pb2+ and Cd2+ were more efficiently removed by the three of them. The simultaneous metal sorption data were analysed according to Langmuir and Freundlich isotherms. Data fitted the Langmuir model only for Ni and Cd, but Freundlich isotherm for all metals tested, as it was expected. The K(F) values showed that Pb was the metal more efficiently removed from water solution. The adsorption process for the three species studied followed first order kinetics. The mechanism involved in biosorption resulted ion exchange between monovalent metals as counter ions present in the macrophytes biomass and heavy metal ions and protons taken up from water. No significant differences were observed in the metal exchange amounts while using multi-metal or individual metal solutions.     

The use of a sequential leaching procedure for heavy metal fractionation in green liquor dregs from a causticizing process at a pulp mill

A five-stage sequential leaching procedure was used to fractionate heavy metals (Cd, Cu, Pb, Cr, Zn, Fe, Mn, Ni, Co, As, V, Ba and Ti) in green liquor dregs into the following fractions: (1) water-soluble fraction (H2O), (2) exchangeable fraction (CH3COOH), (3) easily reduced fraction (HONH3Cl), (4) oxidizable fraction (H2O2 + CH3COONH4), and (5) residual fraction (HF + HNO3 + HCl). The green liquor dregs were derived from a causticizing process at a pulp mill at Kemi, Northern Finland. According to the leaching studies, the leachability of heavy metals in the water-soluble fraction varied between 0.5 and 2 mg kg(-1) expressed on a dry weight (d.w.) basis, indicating relatively low bioavailability of the metals. However, the concentration of Mn (2065 mg kg(-1); d.w.) showed a strong and of Zn (17.6 mg kg(-1); d.w.), Ni (39.7 mg kg(-1); d.w.) and Ba (32.0 mg kg(-1); d.w.) slightly tendency to be extracted in the exchangeable fraction. In addition, Zn, Mn, Ni, Co, V and Ba showed clear leachability in the easily reduced fraction, as well as Cd, Cu, Cr, Zn, Mn, As and Ba in the oxidizable fraction. For Cd, Cu, Cr, Zn, Mn, Ni, Co, Ba and Ti, the sum of leachable heavy metal concentrations in fractions 1-5 agreed relatively well with the "total" heavy metal concentrations. Recoveries of the sum of fractions 1-5 were 84-56% of those obtained by the US EPA method 3052 (i.e. concentrations obtained after microwave oven digestion with a mixture of HF and HNO3).     

皂化改性橘子皮生物吸附剂对重金属离子的吸附

以生物废料橘子皮(OP)为原料,经乙醇、氢氧化钠处理,得到改性橘子皮生物吸附剂SOP,将其用于对重金属离子Cu2+、Pb2+、Cd2+、Zn2+和Ni2+的吸附。研究了溶液pH、吸附时间和重金属离子初始浓度对SOP吸附性能的影响。结果表明,重金属离子在生物吸附剂上的吸附速率快,符合准二级动力学方程。SOP对重金属离子的吸附等温线符合Lang-muir模型,根据Langmuir模型计算SOP对Cu2+、Pb2+、Cd2+、Zn2+和Ni2+的饱和吸附量分别为56.82、152.4、66.27、33.90和23.02 mg/g,均高于改性前。常见阳离子的存在对重金属离子吸附的影响较小,改性后的橘子皮生物吸附剂可以再生重复使用4次以上,是性能良好的重金属离子吸附剂。     

Pre-concentration and separation of heavy metal ions by chemically modified waste paper gel

Iminodiacetic acid was immobilized on waste paper by chemical modification in order to develop a new type of adsorption gel for heavy metal ions. Adsorption behavior of the gel was investigated for a number of metal ions, specifically Cu(II), Pb(II), Fe(III), Ni(II), Cd(II), and Co(II) at acidic pH. From batch adsorption tests, the order of selectivity was found to be as follows: Cu(II)  Fe(III) > Pb(II) > Ni(II)  Co(II) > Cd(II). Column tests were carried out for pairs of metal ions to understand the separation and pre-concentration behavior of the gel. It was found that mutual separation of Ni(II) from Co(II) and that of Pb(II) from Cd(II) can be achieved at pH 3. Similarly, selective separation of Cu(II) from Cu(II)–Fe(III) and Cu(II)–Pb(II) mixtures at pH 1.5 and 2, respectively, was observed by using this new adsorption gel. In all cases, almost complete recovery of the adsorbed metal was confirmed by elution tests with HCl.     

Predictions of binary sorption isotherms for the sorption of heavy metals by pine bark using single isotherm data

The adsorption of three heavy metal ions by pine bark was studied. The study was divided into two parts; single component adsorption of the metals Cu2+, Cd2+ and Ni2+ and bisolute adsorption of the three binary systems Cu2+-Cd2+, Cu2+-Ni2+ and Cd2+-Ni2+. Extended Langmuir model, extended Freundlich model. Sips model and ideal adsorption solution theory (IAST) models were used to predict the equilibrium uptake for Cu2+, Cd2+ and Ni2+ in the binary diluted solutions using the single adsorption constants. The experimental data of single isotherm adsorption process were found to follow Langmuir isotherm model with less accuracy than Freundlich and Sips models. Whereas, the predictions of bisolute adsorption isotherms of the mentioned three systems, Cu2+-Cd2+, Cu2+-Ni2+ and Cd2+-Ni2+, showed good agreement with experimental data when using Extended-Langmuir, Extended-Freundlich and IAST. However, the only good fit of the Sips model was with the Cu2+-Cd2+ system.     

Superior photodecomposition of pyrene by metal ion-loaded TiO₂ catalyst under UV light irradiation

BACKGROUND: The photocatalytic degradation of pyrene under UV (125 W Hg-Arc, 10.4 mW/cm2) irradiation of TiO2 aqueous suspension has been found to be highly improved with the dissolved transition metal ions like Cu2+, Fe3+, Ag+, and Au3+, etc. As the reduction potential of these metals lies below the conduction band (CB) position (?0.1 eV) of TiO2, the photoexcited electron transfer occurs more readily and reduces electron–hole recombination rate. Therefore, it has a beneficial influence on the photocatalytic ability of TiO2 because of rapid Fermi energy equilibrium between the CB of TiO2 and its surface adsorbed metal ions. RESULTS AND DISCUSSION: The Fermi level is referred to as the electrochemical potential and plays an important role in the band theory of solids. When metal and semiconductor are in contact, electron migration from photoirradiated semiconductor to the deposited metal occurs at the interface until two Fermi levels equilibrate and enhanced the photocatalytic activity of semiconductor photocatalyst. Ni2+ having more negative reduction potential (?0.25 eV) than the CB of TiO2 imparts negligible co-catalytic activity to TiO2 photoreaction. It also revealed that loading of Au3+ ions displayed higher degradation rate of pyrene than Au photodeposition. Furthermore, when the amount of dissolved Fe+3 and Au3+ ions gradually increases from 0.1 to 2 wt.%, the pyrene photodecomposition rate also become faster.     

Effect of metal ions and humic acid on the dechlorination of tetrachloroethylene by zerovalent iron

The dechlorination of tetrachloroethylene (PCE) by zerovalent iron (Fe(0)) in the presence of metal ions and humic acid was investigated. In the absence of metal ion and humic acid, 64% of the initial PCE was dechlorinated after 125 h with the production of ethane and ethene as the major end products. The dechlorination followed pseudo-first-order kinetics and the normalized surface rate constant (k(SA)) for PCE dechlorination was (3.43+/-0.61)x10(-3)lm(-2)h(-1). Addition of metal ions enhanced the dechlorination efficiency and rate of PCE, and the enhancement effect followed the order Ni(II)>Cu(II)>Co(II). The k(SA) for PCE dechlorination in the presence of metal ions were 2-84 times higher than that in the absence of metal ions. X-ray photoelectron spectroscopy (XPS) showed that Cu(II) and Ni(II) were reduced by Fe(0) to zerovalent metals, and resulted in the formation of bimetallic system to accelerate the dechlorination reaction. On the contrary, humic acid out-competed the reactive sites on iron surface with PCE, and subsequently decreased the dechlorination efficiency and rate of PCE by Fe(0). However, the reactivity of Fe(0) for PCE dechlorination in the presence of metal ions and humic acid increased by a factor of 3-161 when compared to the iron system containing humic acid alone. Since humic acid and metal ions are the most often found co-existing compounds in the contaminated aquifers with chlorinated hydrocarbons, results obtained in this study is useful to better understand the feasibility of using Fe(0) for long-term application to the remediation of contaminated sites.     

Effect of metal ions on decomposition of chlorinated organic substances by ozonation in acetic acid

The objective of this study is to find metal ions that enhance the ozone decomposition of chlorinated organic substances in acetic acid. Although the pseudo-first order degradation rate constant for 2,4-DCP by ozone in acetic acid in addition of Ca2+, Mg2+, Al3+ and Fe2+ were almost the same as that with no metal ion, the degradation rate in addition of Mn2+ and Fe3+ were 2.4 and 4.5 times as high as that with no metal ion, respectively. The presence of Fe3+ enhanced the degradation of 2,4-DCP by ozone in acetic acid because Fe3+-phenolate complex which have high reactivity with ozone was produced by the reaction between 2,4-DCP and Fe3+ in acetic acid.     

Retrieval of heavy metal ions from solution via ferritisation

The paper summarises the results of the studies on retrieval of heavy metal ions in solution by ferritisation and its potential application in waste-water treatment. The optimum procedure for ferritisation of heavy metal ions in solution has been evolved with respect to pH, concentration of Fe2+, rate and time of aeration and temperature. The recommended procedure consists of controlled aeration of the solution containing heavy metal ions and ferrous ions at pH 9.5-10.5 at about 50 degrees C, until the black, granular, magnetic ferrite separates out. The metal ferrites can also be formed, even without heating or forced aeration, by ageing the mixed metal hydroxide precipitate at pH 10 to 11. The metal ferrites formed have been characterised by X-ray diffractometry. The laboratory-scope experiments conducted with synthetic heavy metal solutions as well as actual wastewater from a tanning industry showed that heavy metal ions can be effectively removed from solution to sub-ppm levels. The metal ferrites thus recovered may find commercial application as microwave absorbers, catalysts, metal scavengers, etc. This technique seems to have potential application in simultaneous, one step removal of different heavy metal ions from industrial wastewaters.     

Effects of temperature and pH on conjugal transfer of zinc-resistant plasmids residing in Gram-negative bacteria isolated from industrial effluents

Two zinc (Zn)-resistant strains, AnZn-1 and AnZn-2, which were resistant to ZnSO4 up to 12.5 mg ml(-1) were isolated from industrial effluents. Both were Gram-negative with motile cells. They exhibited tolerance to Ba2+, Ni+, Co2+, Mn2+, Cu2+, Fe2+, Ni2+, Cd2+, kanamycin, chloramphenicol, ampillicin and tetracycline, but were sensitive to Hg2+ and streptomycin. For AnZn-1 and AnZn-2, the optimum pH for growth was 7. Both were facultative anaerobes and had cytochrome oxidase and urease enzymes, while catalase was present only in AnZn-2. Both strains had the ability to hydrolyse gelatin, reduce nitrate, and yield acid from arabinose and rhamnose. The two strains shared maximum characters with Vibrionaceae. Each strain carries a single Zn-resistant conjugative plasmid. The plasmid residing in AnZn-1 (pSH1211) displayed a lower level of resistance than the plasmid of AnZn-2 (pSH1212). Both required a minimum of 24 h for mating and showed highest transfer frequency at 25 degrees C. pSH1211 preferred pH 7 and pSH1212 pH 8.5 for their transfer. Both plasmids, when allowed to mate with Escherichia coli at 25 degrees C, alkaline pH values of 8-8.5 (pSH1211) of pH 7.5 (pSH1212), showed increased transfer frequency.     

利用芦竹修复重金属污染湿地的研究

研究了芦竹(Arundodonaxlinn)对Cu2+、Ni2+、Cr6+重金属污染湿地的响应和对该污染湿地的影响。实验结果表明,芦竹对这3种重金属离子有一定的耐受性,并有不同程度的吸收,Cu2+、Ni2+和Cr6+去除率分别为63.8%,42.3%和34.4%。芦竹在100mg/kg浓度的Cu2+、Ni2+污染湿地中生长正常,在低浓度(55mg/kg)Cr6+污染中能存活,但生长速度较慢。在100mg/kg浓度Cr6+污染湿地中,出现急性中毒现象,半月后致死。在重金属污染环境中,芦竹普遍出现失绿现象,但除高浓度Cr6+(100mg/kg)以外,都能正常存活,表现出较强的适应性。     

Evaluation of heavy metal concentrations of edible wild-grown mushrooms from China

ABSTRACT

The heavy metal contents (Co, Cu, Fe, Mn, Ni, and Zn) of eight species of wild edible mushrooms from China were determined. The analyses were performed using inductively coupled plasma atomic emission spectrophotometry after microwave digestion. The contents of Co, Cu, Fe, Mn, Ni, and Zn in caps of mushroom samples were 0.7–7.2, 16.2–70.4, 371–1315, 12.5–29.8, 7.1–58.5, and 77.8–187.4 mg kg^?1 dry matter (dm), respectively, while considerable differences were found to be 1.8–25.9, 9.8–36.3, 288–6762, 13.3–103.9, 5.9–78.7, and 38.7–118 mg kg^?1 dm for stipes. The results indicated that higher levels of Co, Fe, and Ni were found in the mushrooms samples analyzed. Zinc and manganese levels were similar to previous reports, whereas Cu was lower than literature values. Correlation analysis suggested that significant correlations were found between the minerals determined and the greatest amount of contamination is associated with Co, Mn, Ni, and Fe. The results of this study indicate that heavy metal contents in mushroom species are mainly related to the mineral resources of sampling sites.     

Removal of heavy metals from anaerobically digested sewage sludge by isolated indigenous iron-oxidizing bacteria

The removal of heavy metals (Cr, Cu, Zn, Ni and Pb) from anaerobically digested sludge from the Yuen Long wastewater treatment plant, Hong Kong, has been studied in a batch system using isolated indigenous iron-oxidizing bacteria. The inoculation of indigenous iron-oxidizing bacteria and the addition of FeSO4 accelerated the solubilization of Cr, Cu, Zn, Ni and Pb from the sludge. pH of the sludge decreased with an increase in Fe2+ concentrations and reached a low pH of 2-2.5 for treatments receiving both bacterial inoculation and FeSO4. After 16 days of bioleaching, the following heavy metal removal efficiencies were obtained: Cr 55.3%, Cu 91.5%, Zn 83.3%, Ni 54.4%, and Pb 16.2%. In contrast, only 2.6% of Cr, 42.9% of Cu, 72.1% of Zn, 22.8% of Ni and 0.56% of Pb were extracted from the control without the bacterial inoculation and addition of FeSO4. The residual heavy metal content in the leached sludge was acceptable for unrestricted use for agriculture. The experimental results confirmed the effectiveness of using the isolated iron-oxidizing bacteria for the removal of heavy metals from sewage sludge.     

Relationship between heavy metals concentrations in egret species,their environment and food chain differences from two Headworks of Pakistan

Concentration of ten metals (Cd, Cr, Co, Cu, Fe, Li, Mn, Ni, Pb and Zn) were analyzed in the egg contents, prey and soil samples of little egret (Egretta garzetta) and cattle egret (Bubulcus ibis) from two Headworks to determine habitat and species-specific differences; to assess the importance of prey and habitat contamination as an exposure source for heavy metals. Concentration of Cu, Mn, Cr and Pb in egg contents, Fe, Co, Cu, Mn, Zn in prey and Fe, Co, Cu, Ni, Li in surface soils were significantly different (P < 0.05). Mean metal concentrations of Cr, Pb and Cd were relatively higher in little egret whereas Cu and Mn were higher in the egg contents of cattle egret. The mean concentrations of Cu, Mn and Zn were higher in prey samples of cattle egrets and Cr, Cd and Pb in prey samples of little egrets. In soil samples collected from little egret heronries metal concentrations were higher except Cu and Ni. Correlation Analysis and Hierarchical Agglomerative Cluster Analysis (HACA) identified relatively similar associations of metals and their source identification. Metals such as Fe, Cu, Mn, and Li were related with geochemical origin from parent rock material as well as anthropogenic input whereas Cr, Cd, Pb, Ni, Co and Zn were associated mostly with anthropogenic activities. The study suggested that eggs are useful bio-monitor of local heavy metal contamination.