电化学方法降解酸性红B研究

研究了成对电氧化技术降解酸性红B染料废水过程.通过高效液相色谱(HPLC)对阴阳极室降解过程中的产物进行了检测,结合UV-Vis变化曲线及TOC、COD_Cr变化过程,发现阳极室脱色比较快,生成多种中间物质;阴极室中间产物很少且降解更完全.电解140min时阴极室中TOC和COD_Cr去除率分别达到71.70%和56.40%,而阳极室中去除率分别为25.15%和27.57%.实验结果表明,阴阳极室中生成氧化物质的氧化能力不同而使酸性红B在阴阳极室按不同的机理降解.     

铁刨花-Fenton-絮凝工艺对染料生产废水中AOX、色度和TOC的去除效果研究

采用铁刨花-Fenton-絮凝工艺处理染料生产废水,考察了不同Fe~(2+)与H_2O_2摩尔比(1∶3~1∶15)、铁刨花反应时间(2~5h)、Fenton氧化反应时间(20~80 min)下可吸附性有机卤代物(AOX)、色度和总有机碳(TOC)的去除效果.结果表明,AOX、色度和TOC去除率随Fe~(2+)与H_2O_2摩尔比的降低先升高后减少,随铁刨花和Fenton反应时间的增加而持续升高.最优化条件为Fe~(2+)与H_2O_2摩尔比1∶8、铁刨花反应时间4 h和Fenton反应时间60 min,该条件下AOX、色度和TOC的去除率分别为94.2%、93.7%和27.2%.比较实验结果表明,铁刨花-Fenton-絮凝组合工艺对废水AOX、色度和TOC的去除效果远优于铁刨花处理、Fenton氧化、絮凝沉淀的单个技术或两两技术组合效果.GC-MS分析表明,废水中的有机卤代物和苯胺类污染物得到高效去除,此外硝基苯类、苯酚类、苯甲醛类、醚类、腈类和杂环化合物等有毒有害物质也均得到高效去除.叔丁醇捕获·OH实验表明·OH在Fenton反应中的主导作用.     

新生态型聚硅酸铁锰处理染料废水的优化

为了提高混凝剂对染料废水的净化效率,本文利用硅酸钠、硫酸亚铁和高锰酸钾为原料合成了新型复配混凝剂聚硅酸铁锰(PSFM),分别以直接大红、分散蓝和活性黄染料废水为处理对象进行混凝模拟实验,研究了碱度和浊度等因素对PSFM混凝去除染料性能影响.结果表明,PSFM对直接大红和分散蓝染料废水具有较好的混凝净化效能,其色度和TOC去除率分别可达99.2%、95.4%和98.5%、93.8%,效果优于聚硅酸铁(PSF)、Al2(SO4)3和Fe Cl3等常规混凝剂,PSFM对活性黄染料废水色度和TOC去除率分别为56.3%和51.3%.浊度对PSFM混凝效能无明显影响.在碱度分别为50、0和75 mg·L~(-1)时,PSFM对直接大红、分散蓝和活性黄去除率分别达到最高.此外,利用扫描电子显微镜(SEM)、傅里叶红外(FTIR)和X射线衍射仪(XRD)等高级表征手段对PSFM进行了表征,对混凝过程中的混合液和絮体分别进行Zeta电位和絮体粒径在线监测,探索得PSFM混凝主要机制为Fe+与Mn+水解产生的带正电的多核配合物和聚硅的桥联聚合,同时还包括新生态水合二氧化锰和羟基氧化铁的吸附助凝作用.     

Removal natural organic matter in typical south-China source water during enhanced coagulation of a with IPF-PACl

Systematic investigation on enhancing removal of natural organic matter （NOM） using inorganic polymer flocculant （IPF）, polyaluminum chloride（PACI） and polyacrylamide（PAM） was performed in a typical south-China source water. Enhanced coagulation and applying polymer flocculant-aid were compared through jar tests and pilot tests. Raw water and settled water were characterized and fractionated by resin adsorption. The results show that DOC composes major part of TOC. The DOC distribution keeps relatively stable all around the year with typical high amounts of the hydrophilic matter around 50%. The distribution between HoB, HoA and HoN varies and undergoes fluctuation with the year round. During the summer season, the HoN becomes gradually the major part in hydrophobic parts. PACI with the species being tailor-made shows little pH effect during coagulation. The enhanced coagulation dosage for PACI could be 4.5 mg/L for the typical source water. The highest TOC removal achieved 31%. To be economically, 3 mg/L dose is the optimum dosage. Although hydrophilic fractions of NOM of both treatment strategies are removed about 30%, NOM causing UV254 absorbance were well removed（about 90%）. Hydrophobic bases and acids fractions are much more removed under enhanced conditions. The hydrophilic fraction could be better removed using PAM, the polymer coagulant aid.     

Enhanced removal of organics by permanganate preoxidation using tannic acid as a model compound – Role of in situ formed manganese dioxide

The effect of permanganate preoxidation on organic matter removal during the coagulation with aluminum chloride was investigated using tannic acid as a model compound. Results showed that a small amount of KMnO4 (0.75 mg/L) increased the removal efficiency of tannic acid up to 20%, as compared to the process of coagulation by aluminum chloride alone. The key factor enhancing the removal efficiency of tannic acid in preoxidation process was the in situ formation of a reductant manganese dioxide. The complexation model was used to describe the reaction between MnO2 and tannic acid. Under weak pH condition, tannic acid was difficult to be adsorbed by MnO2 due to the static electrical repulsive forces. The presence of Ca2+ served as a bridge to hold the negative charged MnO2 and tannic acid together, which could be a crucial factor influencing tannic acid adsorption by in-situ manganese dioxide.     

电絮凝-过滤法去除源水中微量有机物

利用电絮凝-过滤法进行了源水中有机物去除的实验研究,探讨了电流密度、电解时间和pH值等因素对源水中TOC去除效果的影响。结果表明,在电极间距1.0cm,电流密度47.2 A/m2,初始TOC浓度为12.4mg/L时,反应12min后,出水浓度为3.60mg/L,TOC去除率可达71%。表明电絮凝法可有效去除源水中微量有机物。其去除机理包括电絮凝、电化学氧化和还原以及电气浮等。     

Al-Cu双金属体系对活性艳红X-3B的脱色研究

以典型偶氮染料活性艳红X-3B为模型污染物,采用测定染料去除率、TOC去除率、苯胺生成量的方法及添加EDTA的对照试验,考察Al-Cu双金属体系对偶氮染料废水的脱色机理和脱色动力学.结果表明,在近中性条件下处理30min后脱色率就可达到83%左右;处理120min后脱色率高达96.4%,其中约为34%的色度去除是由于活性艳红X-3B被还原为苯胺,约为20%和30%的色度去除是由于铝离子混凝和铝刨花表面吸附.染料废水脱色是一个先大量吸附再进行内电解还原逐步降解的过程,铝离子的絮凝-吸附作用能有效促进色度的去除.脱色反应可视为表观一级反应,提高反应温度可以加快脱色速率.     

酸热氧化修饰合成MnOx/GAC催化臭氧氧化降解邻氯酚

通过酸热氧化修饰法在活性炭上负载锰氧化物,制得MnO_x/GAC催化剂,并研究其催化臭氧氧化降解邻氯酚的性能。结果表明:在催化剂投加量为0.1 g/L,臭氧浓度为20 mg/L,气体流量为0.5 L/min,初始pH为6的条件下,反应120 min时,邻氯酚的TOC去除率可达到95%,比单纯臭氧氧化提高了55百分点。在一定范围内,增加臭氧浓度和气体流量可以加快反应速率,提高TOC去除率,但通入过量的臭氧反而会降低TOC去除率。探究了无机阴离子对于体系TOC去除率的影响,研究发现:1 mmol/L的NO₃-、SO₄2-、Cl-对TOC去除率无明显影响,1 mmol/L Br-使体系TOC去除率降低了10%左右。pH是影响体系氧化能力的重要因素,在酸性条件下的TOC去除率远高于碱性条件下,这可能与催化剂表面官能团的作用和反应体系中无机碳的积累有关。此外,提出了催化剂表面羟基存在形式与pH之间的关系,以及不同羟基存在形式下催化臭氧分解产生的活性物种。     

Effects of pre-ozonation on organic matter removal by coagulation with IPF-PACI

Ozone plays an important role as a disinfectant and oxidant in potable water treatment practice and is increasingly being used as a pre-oxidant before coagulation. The purpose of this study is to obtain insight into the mechanisms that are operative in pre-ozonized coagulation. Effects ofpre-ozonation on organic matter removal during coagulation with IPF-PAC1 were investigated by using PDA （photometric disperse analysis）, apparent molecular weight distribution and chemical fractionation. The dynamic formation of flocs during coagulation process was detected. Changes of aquatic organic matter （AOM） structure resulted from the influence of pre-ozonation were evaluated. Results show that dosage of O3 and characteristics of AOM are two of the major factors influencing the performance of O3 on coagulation. No significant coagulation-aid effect of O3 was observed for all experiments using either A1C13 or PAC1. On the contrary, with the application of pre-ozonation, the coagulation efficiency of A1C13 was significantly deteriorated, reflected by the retardation of floc formation, and the removal decreases of turbidity, DOC, and UV254. However, if PACl was used instead of AlCl3, the adverse effects of pre-ozonation were mitigated obviously, particularly when the O3 dosage was less than 0.69 （mg O3/mg TOC）. The difference between removals of UV254, and DOC indicated that pre-ozonation greatly changed the molecular structure of AOM, but its capability of mineralization was not remarkable. Only 5% or so DOC was removed by pre-ozonation at 0.6--0.8 mg/L alone. Fractionation results showed that the organic products of pre-ozonation exhibited lower molecular weight and more hydrophilicity, which impaired the removal of DOC in the following coagulation process.     

紫外光在臭氧降解不同有机物过程中的协同作用

利用O3／UV分别对与臭氧有不同反应活性的对氯苯酚、硝基苯、乙酸和草酸进行了降解试验,结果表明,UV与臭氧化降解的协同作用与目标有机物本身的性质有很大关系,在本实验条件下,UV与臭氧的联用反而降低了对氯苯酚的臭氧化降解效率,30min后体系的TOC去除率仅有59％,而单独臭氧化TOC的去除率达到了66％;对硝基苯和草酸而言,UV均明显地提高了臭氧的降解效率,40min时两者TOC的去除率分别为44％和90％,比单独臭氧化处理分别高出了6％和33％;但是,O3／UV对乙酸几乎无降解活性．在这4种有机物的单独臭氧化降解过程中,除对氯苯酚外,水中均可检测到溶解臭氧．以上的实验结果表明,目标有机物对紫外光的吸收及单独臭氧化过程水中溶解臭氧的存在是O3／UV降解效率提高的必要条件．除UV对目标有机物的活化作用外,降解过程的中间产物H2O2也是O3／UV降解效率提高的一个重要因素,UV分解溶解臭氧在此过程可能仅起了辅助作用。     

臭氧-紫外预处理对高有机物原水混凝效果的影响

以腐殖酸为模型污染物,分别考察了臭氧氧化、紫外照射及臭氧-紫外联合预处理过程对高有机物原水混凝性能的影响.结果表明,3种预处理方式均对原水中的溶解性腐殖酸具有明显的矿化作用.紫外及臭氧-紫外联合预处理还对后续的混凝过程具有强化作用.随着臭氧投量的增加和紫外照射时间的延长,混凝过滤出水的TOC和浊度呈明显下降趋势.当臭氧浓度(O3/C)达到9.0 mg/mg时,预处理对腐殖酸的去除率可以达到47%,过滤出水TOC含量为3.5 mg/L,浊度为2.6 NTU;紫外光照射3 h可去除原水中52%的溶解性有机物,其出水TOC为2.0 mg/L,浊度低于1.0 NTU.臭氧-紫外联合预处理后的混凝效果要明显优于二者单独作用的系统.在联合预处理系统中,当预臭氧浓度(O3/C)为1.0 mg/mg紫外照射时间为1 h时,过滤出水TOC为2.6 mg/L,且浊度低于1.0 NTU.不同预处理条件下的矿化作用主要是通过.OH实现的,同时.OH还对溶解性腐殖酸的团聚结构产生破坏作用,使其稳定性降低,从而促进了混凝过程对有机物的去除.     

电-多相臭氧催化技术处理金刚烷胺制药废水

采用电-多相臭氧催化（E-catazone）技术处理高COD、高含盐、难生化的金刚烷胺制药废水.对比研究电-多相臭氧催化、多相臭氧催化（Catazone）、电催化氧化（EO）对金刚烷胺制药废水的处理效果,在此基础上进一步研究了电流密度、pH值以及气相O₃浓度对电-多相臭氧催化技术处理效果的影响,同时优化实验条件.实验结果表明,在原水pH值为12.5,电流密度为15mA/cm²,O₃进气流速0.4L/min,O₃浓度为60mg/L的条件下,经过60min反应,电-多相臭氧催化技术获得了62%的COD去除和44%的总有机碳（TOC）去除,其效果显著优于多相臭氧催化（COD 44%,TOC 29%）与电催化氧化（COD 13%,TOC 17%）;同时,电-多相臭氧催化不仅氧化能力强,而且氧化速率快,获得的伪一级COD去除速率常数k是多相臭氧催化和电催化氧化的1.81倍和8.22倍,更为重要的是,电-多相臭氧催化技术还可以高效、快速地提高废水的生化性,提高约2个数量级,结果表明,电-多相臭氧催化技术是一种有潜力的高级氧化技术,可以实现高效、快速去除有机污染物以及提高废水的可生化性.     

磁性离子交换树脂对原水中有机物去除效能的研究

采用磁性离子交换树脂(MIEX)预处理原水中有机物的中试试验结果表明,MIEX技术可有效地去除原水中的有机物,对UV254,DOC和CODMn的去除率分别稳定在82%、66%和50%,MIEX预处理可以有效强化混凝沉淀对有机物、藻细胞和浊度的去除.与常规工艺相比,在混凝剂聚合氯化铝投加量降低56%时,该工艺对UV254和CODMn的去除率分别为90%和71%,对藻细胞数和浊度的去除率分别为99%和95%.对溶解性有机物分级和分子量分布的测定表明,MIEX预处理主要去除混凝沉淀无法有效去除的小分子区间的亲水性和疏水性有机物,可以有效控制消毒副产物的产生,MIEX预处理与混凝沉淀联用工艺出水的三卤甲烷生成势(THMFP)和卤乙酸生成势(HAAFP)比原水降低了88%和87%.     

混凝法处理锰矿选矿废水的试验研究

选取聚合氯化铝（PAC）、聚合硫酸铁（PFS）、聚丙烯酰胺（PAM）和六水合氯化铁（FC）4种常用混凝剂,采用正交试验,以去浊率与去锰率作为综合评价指标,探讨了不同混凝剂处理锰矿选矿废水的效果及最佳混凝条件。结果表明：在以上混凝剂中,FC的混凝效果较差;PAM对锰矿选矿废水的处理效果最优,最佳的混凝条件为：处理500 ml的废水,投加1.5 ml的PAM,pH为7.0,搅拌后沉降20 min,废水经处理后去浊率与去锰率分别为96%、92%,其中废水的pH及投药量对混凝效果的影响较大。     

强化混凝去除微污染湖泊水浊度及TOC的研究

通过烧杯混凝试验和动态连续混凝试验,就混凝剂种类、投药量、pH值、水温等因素,研究强化混凝对水中浊度和TOC去除效果的影响。试验结果表明:PAC最佳投量为30mg/L,浊度去除率为90.19%,TOC去除率为38.2%,水温高于20℃时,聚合氯化铝对浊度和TOC去除率分别高达84.95%、33.18%以上。虽然pH值是影响有机物去除的主要参数,动态连续混凝试验表明,不改变pH值,强化混凝工艺依然能极大地改善出水水质,滤后水质浊度为0.1NTU,TOC为6.23mg/L。     

Comparison of different disinfection processes in the effective removal of antibiotic-resistant bacteria and genes

This study compared three different disinfection processes(chlorination, E-beam, and ozone) and the efficacy of three oxidants(H2O2, S2O-8, and peroxymonosulfate(MPS)) in removing antibiotic resistant bacteria(ARB) and antibiotic resistance genes(ARGs) in a synthetic wastewater. More than30 mg/L of chlorine was needed to remove over 90% of ARB and ARG. For the E-beam method, only1 dose(kGy) was needed to remove ARB and ARG, and ozone could reduce ARB and ARG by more than 90% even at 3 mg/L ozone concentration. In the ozone process, CT values(concentration × time)were compared for ozone alone and combined with different catalysts based on the 2-log removal of ARB and ARG. Ozone treatment yielded a value of 31 and 33(mg·min)/L for ARB and ARGs respectively. On the other hand, ozone with persulfate yielded 15.9 and 18.5(mg·min)/L while ozone with monopersulfate yielded a value of 12 and 14.5(mg·min)/L. This implies that the addition of these catalysts significantly reduces the contact time to achieve a 2-log removal, thus enhancing the process in terms of its kinetics.     

新生态MnO2强化混凝去除苯酚的影响因素研究

以苯酚为目标物,考察钙离子、单宁酸、高岭土投量、新生态二氧化锰投量、pH等条件对新生态二氧化锰强化氯化铝混凝去除苯酚的影响.结果表明,钙离子能够促进新生态二氧化锰强化混凝对苯酚的去除,在钙离子投加范围内（0～1.0mmol.L-1）,苯酚的去除率能提高10%左右;单宁酸与苯酚共存时,能显著促进苯酚的去除,当单宁酸投加1...     

Ru/AC催化臭氧氧化难生物降解有机物

研究了臭氧单独氧化和Ru/AC催化臭氧氧化DMP、酚类物质和消毒副产物前体物.结果表明,Ru/AC能显著提高臭氧氧化中有机物的矿化效果.在DMP降解中,反应100 min后TOC的去除率由单独臭氧氧化的28.84%提高到66.13%.在23种酚类物质降解中,反应60min后TOC的去除率由单独臭氧的9.57%~56.08%提高到41.81%~82.32%.相对于单独臭氧,Ru/AC催化臭氧氧化更能有效地降低水源水中消毒副产物的生成势,以卤乙酸生成势的降低最为明显,100 min后卤乙酸生成势由144.02μg/L降到58.50μg/L,低于美国环保局规定的限制浓度60μg/L.而使用单独臭氧处理并不能使卤乙酸生成势降到符合美国EPA的规定.比较了BAC、O3+BAC、O3/AC+BAC以及Ru/AC+O3+BAC工艺处理水源水的效果,TOC平均去除率分别为3.80%、20.14%、27.45%和48.30%;COD平均去除率分别为4.37%、27.22%、39.91%和50.00%;UV254去除率分别为8.16%、62.24%、67.03%和84.95%.Ru/AC+O3+BAC工艺相比其他工艺,更能有效地...     

强化原位生物接触氧化技术改善水源水质的试验研究

在扬水曝气条件下,在原位进行了强化生物接触氧化技术改善滦河水源水质的试验研究,分析测定其处理效果,研究了生物填料悬挂于自然水体不同水深、不同水力停留时间下对生物预处理效果的影响.试验结果表明,扬水曝气加原位采用生物接触氧化组合用于水源水质改善是可行的;该技术对水中CODMn、氨氮、叶绿素a、真实色度、TOC、UV254、铁和锰平均的去除率分别可达10.1%、64.1%、42.4%、48.6%、12.5%、9.5%、48.9%和41.9%;生物填料可悬挂在水体0～3 m水深区,停留时间应大于2～3 h.     

MIEX预处理技术对长江原水中有机物的去除效能

利用烧杯试验研究了磁性离子交换树脂（magnetic ion exchange resin,MIEX）预处理对长江原水中有机物的去除效能,以总溶解有机碳(DOC)、254 nm紫外吸收值(UV254)、有机物相对分子质量分布、有机物分级、紫外扫描以及消毒副产物生成量等指标进行表征.结果表明,长江水源水中的有机物主要为小分子亲水性有机物,其含量占有机物总量的50%以上;MIEX预处理可以有效降低水中有机物的含量,投加量为10 mL/L、接触时间为15 min时,DOC的去除率超过35%,相对分子质量和分级的测定结果表明,小分子亲水性部分有机物的去除导致了DOC去除效果的改善;从紫外扫描结果可看出,MIEX预处理对在190～250 nm波长时有强吸收的有机物去除效果非常明显,但对在高于250 nm波长处有吸收的有机物去除效果与混凝阶段的效果相近.