Reactions of the amine-containing drugs fluoxetine and metoprolol during chlorination and dechlorination processes used in wastewater treatment

The reactivities of the amine-containing pharmaceuticals fluoxetine and metoprolol with hypochlorite were studied using conditions that simulate wastewater disinfection including neutral pH (7.0), a range of reaction times (2–60 min), and a molar excess of hypochlorite relative to the pharmaceutical concentration (5.7 times). The reactions were monitored using liquid chromatography (LC) with several detection modes including ultraviolet absorbance (UV), mass spectrometry (MS), and post-column reaction/reductive electrochemistry (EC) for determining active chlorine products. At levels of 10 μM, both compounds reacted rapidly (<2 min) to form principally N-chloramine products that were stable in aqueous solution for at least 1 h. The reaction was also studied in wastewater, and similar reactivity was noted. These results demonstrate that the cations fluoxetine and metoprolol are likely to be rapidly transformed into neutral N-chloramines during wastewater disinfection. The reactivity of the N-chloramines was also studied with sulfite to simulate dechlorination, which is often employed in wastewater treatment. Both N-chloramines reacted slowly with sulfite. In the pure water dechlorination experiments, it was estimated that 70% and 10% of the peak areas remained after 2 min reaction time for fluoxetine and metoprolol, respectively. At longer reaction times both N-chloramines had been completely reduced by sulfite, and the product of the sulfite reduction reaction was the parent pharmaceutical amine. Since typical dechlorination times in wastewater treatment are on the order of seconds, this suggests the chloramines formed from these two basic drugs might evade dechlorination and be released into the environment. The implications of chloramine release are discussed.     

Formation of free cyanide and cyanogen chloride from chloramination of publicly owned treatment works secondary effluent: laboratory study with model compounds.

The potential generation of cyanide species in wastewater upon chlorination in the presence of residual ammonia (resulting in chloramine formation) was investigated in experiments with synthetic solutions and publicly owned treatment works (POTW) secondary effluent. This study demonstrated that low concentrations (approximately 5 to 25 microg/L as cyanide) of cyanogen chloride (CNCI), a highly toxic cyanide species not measured in total or free cyanide analyses, could be detected as a result of chloramination reactions in POTW secondary effluent. The potential for chloramination of nitrogen-bearing organic compounds to yield CNCl and/or free cyanide was demonstrated in experiments with synthetic solutions spiked with selected precursor organics: L-serine, benzene, catechin, and humic acid. The amino acid L-serine yielded the largest concentrations of CNCI upon chloramination. Additionally, detectable cyanide (approximately 10 microg/L) was observed in solutions of L-serine and in POTW secondary effluent that was chloraminated followed by dechlorination to prevent destruction of any free cyanide produced. Thus, chlorination of POTW secondary effluent containing residual ammonia can lead to chloramination of organic compounds and the resulting production of CNCl and free cyanide.     

Sulfur speciation: Methodology and application to sulfide oxidation studies at the sediment-water interface

A single column ion chromatographic method for the determination of sulfide, sulfite, sulfate and thiosulfate was developed. It uses an anion exchange column (Waters, IC-Pak A) and a borate-gluconate buffer at pH 8.5 that contains EDTA and ascorbic acid to prevent sulfite oxidation. This eluent has relatively low background values for both conductivity and ultraviolet absorption, which allows determination of the above sulfur anions with high sensitivity. The mean percent recovery of the investigated anions in synthetic mixtures were 98.6, 100.0, 99.6 and 100.2 % for sulfide, sulfite, thiosulfate and sulfate, respectively. The method was applied to study sulfide ion oxidation at the water-sediment interface using six aquifer samples collected within the continental United States. Results indicated that sulfide ion disappearance follows a pseudo first-order profile and that the rate of disappearance correlates with the total organic carbon and clay content of the sediment.     

Reactions of the amine-containing drugs fluoxetine and metoprolol during chlorination and dechlorination processes used in wastewater treatment

The reactivities of the amine-containing pharmaceuticals fluoxetine and metoprolol with hypochlorite were studied using conditions that simulate wastewater disinfection including neutral pH (7.0), a range of reaction times (2–60 min), and a molar excess of hypochlorite relative to the pharmaceutical concentration (5.7 times). The reactions were monitored using liquid chromatography (LC) with several detection modes including ultraviolet absorbance (UV), mass spectrometry (MS), and post-column reaction/reductive electrochemistry (EC) for determining active chlorine products. At levels of 10 μM, both compounds reacted rapidly (<2 min) to form principally N-chloramine products that were stable in aqueous solution for at least 1 h. The reaction was also studied in wastewater, and similar reactivity was noted. These results demonstrate that the cations fluoxetine and metoprolol are likely to be rapidly transformed into neutral N-chloramines during wastewater disinfection. The reactivity of the N-chloramines was also studied with sulfite to simulate dechlorination, which is often employed in wastewater treatment. Both N-chloramines reacted slowly with sulfite. In the pure water dechlorination experiments, it was estimated that 70% and 10% of the peak areas remained after 2 min reaction time for fluoxetine and metoprolol, respectively. At longer reaction times both N-chloramines had been completely reduced by sulfite, and the product of the sulfite reduction reaction was the parent pharmaceutical amine. Since typical dechlorination times in wastewater treatment are on the order of seconds, this suggests the chloramines formed from these two basic drugs might evade dechlorination and be released into the environment. The implications of chloramine release are discussed.     

Effect of metal ions and humic acid on the dechlorination of tetrachloroethylene by zerovalent iron

The dechlorination of tetrachloroethylene (PCE) by zerovalent iron (Fe(0)) in the presence of metal ions and humic acid was investigated. In the absence of metal ion and humic acid, 64% of the initial PCE was dechlorinated after 125 h with the production of ethane and ethene as the major end products. The dechlorination followed pseudo-first-order kinetics and the normalized surface rate constant (k(SA)) for PCE dechlorination was (3.43+/-0.61)x10(-3)lm(-2)h(-1). Addition of metal ions enhanced the dechlorination efficiency and rate of PCE, and the enhancement effect followed the order Ni(II)>Cu(II)>Co(II). The k(SA) for PCE dechlorination in the presence of metal ions were 2-84 times higher than that in the absence of metal ions. X-ray photoelectron spectroscopy (XPS) showed that Cu(II) and Ni(II) were reduced by Fe(0) to zerovalent metals, and resulted in the formation of bimetallic system to accelerate the dechlorination reaction. On the contrary, humic acid out-competed the reactive sites on iron surface with PCE, and subsequently decreased the dechlorination efficiency and rate of PCE by Fe(0). However, the reactivity of Fe(0) for PCE dechlorination in the presence of metal ions and humic acid increased by a factor of 3-161 when compared to the iron system containing humic acid alone. Since humic acid and metal ions are the most often found co-existing compounds in the contaminated aquifers with chlorinated hydrocarbons, results obtained in this study is useful to better understand the feasibility of using Fe(0) for long-term application to the remediation of contaminated sites.     

Removal of genotoxicity in chlorinated secondary effluent of a domestic wastewater treatment plant during dechlorination

Purpose  

Dechlorination with tetravalent sulfur is widely used in wastewater treatment processes after chlorination. Dechlorination can remove certain genotoxic disinfection by-products (DBPs). However, the reactions occurring during dechlorination of chlorinated secondary effluent and their genotoxic chemicals are still very complex, and the related genotoxicity changes remain unknown. Therefore, the effects of dechlorination on genotoxicity in secondary effluent and its fractions and typical genotoxic chemical after chlorination were evaluated.     

The occurrence of cyanide formation in six full-scale publicly owned treatment works.

This paper presents results from an intensive monitoring program implemented at six full-scale publicly owned treatment works (POTWs) to investigate the fate and formation of cyanide in wastewater treatment processes, with a focus on chlorination and dechlorination processes. A review of historical monitoring data for cyanide species in these POTWs was also conducted. This POTW monitoring program provided a database for the investigation of cyanide formation in wastewater secondary treatment. Data from participating POTWs showed evidence of cyanide formation in this 1-year monitoring effort, although the cyanide formation pattern varied significantly from one plant to another and among seasons. Generally, the chlorination of thiocyanate (SCN-) seems to be the most important mechanism for the formation of cyanide in wastewater treatment processes, especially in chlorination and dechlorination. This hypothesis is supported by the findings of a related laboratory study of mechanisms of cyanide formation in POTWs. It is recommended that POTWs monitor SCN in influent and secondary effluent to identify its presence and adjust chlorine dose appropriately.     

Evaluation of disinfection techniques in the treatment of advanced primary treated wastewater for Ciudad Juárez, México.

The purpose of this study was to develop and evaluate the effectiveness of alternative disinfection techniques at the bench-scale level using wastewater from Ciudad Juarez, Mexico, as model feed. This paper presents findings on the effectiveness of UV radiation, peracetic acid (PAA), chlorine dioxide (ClO2), and hypochlorous acid (HOCl) as disinfectants for advanced primary treatment (APT) plant effluent. Wastewater samples for bench-scale testing were collected from an agua negra ("black water") ditch that is part of the combined sewer system in Ciudad Juarez. Bench-scale simulations of the APT process used in Ciudad Juarez were run using a jar test apparatus and aluminum sulfate [Al2(SO4)3] as the coagulant. Jar test effluent from the bench system was used for disinfection testing. The Mexican discharge quality standard for total coliforms is 10 000/100 mL. Ultraviolet radiation met this standard at a dose of 47.5 mW-s/cm2. Ultraviolet disinfection proved reliable and effective despite the presence of suspended solids, and UV dose effectiveness expressed as a total coliforms survival ratio was best explained by a linear regression model. The ClO2 dose ranged from 10 to 20 mg/L and was only effective under ambient temperature conditions found during the winter months; PAA disinfection never met Mexican standards. Chlorine disinfection was effective at a dose range of 8 to 10 mg/L on samples collected at low temperature conditions. Since the completion of this research, Ciudad Juarez has discontinued the use of chlorine disinfection because of its high cost and ineffectiveness.     

Investigation and modeling of solar UV-induced chlorine decay in disinfection contact basins at full-scale wastewater treatment plants

Residual chlorine loss due to UV sunlight in the chlorine disinfection contact basins (DCBs) was investigated at two full-scale wastewater treatment plants (WWTPs). Chlorine decay due to solar UV-induced photochemical reaction was found to be significant and had diurnal and seasonal variations. The total chlorine loss due to sunlight ranged from 19 to 26% of the total chlorine chemical use at the two plants studied. Covering chlorine contact basins led to more stable chlorine demand regardless of the diurnal and seasonal sunlight intensity. Therefore, covering chlorine contact basins offers more stable, or accurate, chlorine dosage and effluent residual control and requires less effort by plant operators. A mathematical model was developed to calculate the amount of UV-induced chlorine decay. The model developed can be used to estimate the UV-induced chlorine decay rate and total chlorine loss due to sunlight at WWTPs with various basin configurations, flowrates, chlorine dosages, and geographical locations. The model results allow the capital cost of covering needs to be assessed against the chlorine chemical cost savings.     

Removal and formation of chlorinated triclosan derivatives in wastewater treatment plants using chlorine and UV disinfection

Triclosan, a common antimicrobial agent, may react during the disinfection of wastewater with free chlorine to form three chlorinated triclosan derivatives (CTDs). This is of concern because the CTDs may be photochemically transformed to tri- and tetra-chlorinated dibenzo-p-dioxins when discharged into natural waters. In this study, wastewater influent, secondary (pre-disinfection) effluent, and final (post-disinfection) effluent samples were collected on two occasions each from two activated sludge wastewater treatment plants, one using chlorine disinfection and one using UV disinfection. Concentrations of triclosan and three CTDs were determined using ultra performance liquid chromatography-triple quadrupole mass spectrometry with isotope dilution methodology. Triclosan and the CTDs were detected in every influent sample at levels ranging from 453 to 4530 and 2 to 98 ng L⁻¹, respectively, though both were efficiently removed from the liquid phase during activated sludge treatment. Triclosan concentrations in the pre-disinfection effluent ranged from 36 to 212 ng L⁻¹, while CTD concentrations were below the limit of quantification (1 ng L⁻¹) for most samples. In the treatment plant that used chlorine disinfection, triclosan concentrations decreased while CTDs were formed during chlorination, as evidenced by CTD levels as high as 22 ng L⁻¹ in the final effluent. No CTDs were detected in the final effluent of the treatment plant that used UV disinfection. The total CTD concentration in the final effluent of the chlorinating treatment plant reached nearly one third of the triclosan concentration, demonstrating that the chlorine disinfection step played a substantial role in the fate of triclosan in this system.     

Cyanide generation during preservation of chlorinated wastewater effluent samples for total cyanide analysis.

Dechlorinating agents and pH adjustment are often used to preserve wastewater samples for cyanide analysis. The effects of four approved preservation protocols on the results of the total cyanide analysis of effluents from four water reclamation plants were examined. The results differed widely, and a clear pattern emerged. Immediate analysis without pH adjustment generally gave total cyanide concentrations below the reporting limit of 5 microg/L, irrespective of the dechlorinating agents used. When the pH was adjusted to > or =12, a slight increase in the measured total cyanide concentration was observed when thiosulfate was used to dechlorinate the samples, and a significant increase (>10 microg/L) was observed when arsenite was used as the dechlorinating agent. These results provide evidence that approved preservation protocols may give rise to cyanide formation in chlorinated wastewater effluent matrices.     

ClO2对医院高浓度含氰废水处理的试验研究

以医院排放的高浓度含氰废水为研究对象,采用"硫酸亚铁+曝气"初级化学处理和ClO2二级深度氧化处理相结合的处理模式,不仅使含氰废水实现无毒化处理,而且使高浓度含氰废水实现资源化回收利用.试验表明,处理后的废水中CN-浓度达到国家排放标准GB8978-1996中的一级标准,为医院高浓度含氰废水的治理提供了一种新的方法.     

Effects of thiocyanate on the formation of free cyanide during chlorination and ultraviolet disinfection of publicly owned treatment works secondary effluent.

Cyanide has been detected in effluent of some publicly owned treatment works (POTWs) at levels exceeding influent concentration. Thiocyanate (SCN-) is a cyanide-related compound encountered in most POTW influents and may be decomposed to free cyanide (CN-) under some circumstances. Effects of SCN- on the formation of cyanide during chlorination and UV disinfection were studied through a laboratory study with synthetic solutions and POTW secondary effluent. Results indicated that CN- was detected in SCN- solutions after chlorination in which the chlorine dose or reaction time was not sufficient to destroy SCN-completely, thus ensuring no residual chlorine to destroy any CN-produced. It was also found that SCN can be broken down to yield cyanide by UV irradiation. In addition, SCN- was observed to cause significant positive error in the conventional total cyanide analysis technique involving acidic distillation and colorimetric measurement when nitrate was present in the sample.     

二氧化氯深度处理垃圾渗滤液研究

利用二氧化氯对生物处理后的垃圾渗滤液进行深度处理，根据废水中有效氯浓度、COD、氨氮及细菌数等参数的分析，初步探讨了不同浓度的二氧化氯在不同处理时间内对垃圾渗滤液的处理效果。结果表明，对于COD初始浓度为450 mg/L左右的水样，二氧化氯的投加浓度达100 mg/L（有效氯），反应时间在50 min时，处理水样可达到同类废水的国家二级排放标准；对于同样条件下的水样，当加入约25 mg/L的二氧化氯时可以杀灭水样中的大肠杆菌，加入浓度达到90 mg/L的二氧化氯时，可以杀灭水样中几乎所有的细菌。     

不同来源废水COD、TOC与Cl-的关系

通过对含盐化工废水(A)、受潮汐影响的河流水(B)、城市生活污水处理厂排水(C)、采油废水(D)4种不同来源废水进行为期15 d的采样监测,测定了其COD、TOC和Cl-浓度,分析比较了3种废水指标之间的关系,其中COD分别使用重铬酸钾法、氯气校正法和碘化钾碱性高锰酸钾法3种方法进行测定.实验结果表明,4种废水Cl-浓...     

Microbial dechlorination of polychlorinated biphenyls in anaerobic sewage sludge.

The potential of a chlorophenol (CP)-adapted consortium to dechlorinate polychlorinated biphenyls (PCBs) in sewage sludge was investigated. Results show that dechlorination rates differed significantly depending on sludge source and PCB congener. Higher total solid concentrations in sewage sludge and higher concentrations of chlorine in PCB resulted in slower dechlorination rates. No significant difference was found for 2,3,4,5-CB dechlorination from pH 6.0 to pH 8.0; however, dechlorination did not occur at pH 9.0 during a 41-day incubation period. Results show that at concentrations of 1 to 10 mg/L, the higher the PCB concentration, the faster the dechlorination rate. In addition, dechlorination rates were in the following order: methanogenic conditions > sulfate-reducing conditions > denitrifying conditions. The addition of acetate, lactate, pyruvate, and ferric chloride decreased lag times and enhanced dechlorination; however, the addition of manganese dioxide had an inhibitory effect. Dechlorination rates were also enhanced by the addition of PCB congeners, including 2,3,4-CB, 2,3,4,5-CB and 2,3,4,5,6-CB in mixture. Overall results show that the CP-adapted consortium has the potential to enhance PCB dechlorination. The optimal dechlorination conditions presented in this paper may be used as a reference for feasibility studies of PCB removal from sludge.     

Catalytic degradation of chlorothalonil in water using bimetallic iron-based systems

Modified zero valent iron (MZVI) was used to study the transformation of a chlorothalonil (CLT) solution and the variation of the observed degradation rate of the reduction reactions. This was carried out when transition metals e.g. Pd, Cu and Co plated on the surface of micrometric iron particles (< 150 microm) were used as reducing catalytic agents for pesticide removal. Reactions were undertaken under both oxic and anoxic conditions in the presence and the absence of a phosphate buffer solution (PBS). Results of batch studies in nitrogen sparged solutions revealed that incomplete slow dechlorination merely occurred with zero valent iron (ZVI), however, complete rapid dechlorination reactions took place with MZVI especially Fe/Pd. Dechlorination was depicted by studying UV absorbance and MS spectra of CLT and all corresponding by-products. Typical blue shifts (deltalambda = 4-6 nm/chlorine atom) were observed at the same time as chlorine cluster isotopes disappeared. After the plating process, metal loading was controlled by analyzing the remaining metal in the solution by atomic absorption spectroscopy. Experiments showed that CLT degradation mechanism is faster in nitrogen sparged solutions in the absence of PBS. Time needed for complete removal of 2.08 +/- 0.19 microM CLT solution was about 2 h when experiments were conducted with ZVI (t1/2 = 15.0 min) and about 10 min when the reaction was carried out under the same conditions with Fe/Pd 1% (t1/2 = 1.0 min). Degradation rates for all bimetallic systems were determined showing that Pd is the more exciting catalytic transition metal followed by Cu and Co. Furthermore, MZVI method showed obvious advantage to traditional CLT treatment methods.     

Effects of wastewater disinfection on waterborne bacteria and viruses.

Wastewater disinfection is practiced with the goal of reducing risks of human exposure to pathogenic microorganisms. In most circumstances, the efficacy of a wastewater disinfection process is regulated and monitored based on measurements of the responses of indicator bacteria. However, inactivation of indicator bacteria does not guarantee an acceptable degree of inactivation among other waterborne microorganisms (e.g., microbial pathogens). Undisinfected effluent samples from several municipal wastewater treatment facilities were collected for analysis. Facilities were selected to provide a broad spectrum of effluent quality, particularly as related to nitrogenous compounds. Samples were subjected to bench-scale chlorination and dechlorination and UV irradiation under conditions that allowed compliance with relevant discharge regulations and such that disinfectant exposures could be accurately quantified. Disinfected samples were subjected to a battery of assays to assess the immediate and long-term effects of wastewater disinfection on waterborne bacteria and viruses. In general, (viable) bacterial populations showed an immediate decline as a result of disinfectant exposure; however, incubation of disinfected samples under conditions that were designed to mimic the conditions in a receiving stream resulted in substantial recovery of the total bacterial community. The bacterial groups that are commonly used as indicators do not provide an accurate representation of the response of the bacterial community to disinfectant exposure and subsequent recovery in the environment. UV irradiation and chlorination/dechlorination both accomplished measurable inactivation of indigenous phage; however, the extent of inactivation was fairly modest under the conditions of disinfection used in this study. UV irradiation was consistently more effective as a virucide than chlorination/dechlorination under the conditions of application, based on measurements of virus (phage) diversity and concentration. Taken together, and when considered in conjunction with previously published research, the results of these experiments illustrate several important limitations of common disinfection processes as applied in the treatment of municipal wastewaters. In general, it is not clear that conventional disinfection processes, as commonly implemented, are effective for control of the risks of disease transmission, particularly those associated with viral pathogens. Microbial quality in receiving streams may not be substantially improved by the application of these disinfection processes; under some circumstances, an argument can be made that disinfection may actually yield a decrease in effluent and receiving water quality. Decisions regarding the need for effluent disinfection must account for site-specific characteristics, but it is not clear that disinfection of municipal wastewater effluents is necessary or beneficial for all facilities. When direct human contact or ingestion of municipal wastewater effluents is likely, disinfection may be necessary. Under these circumstances, UV irradiation appears to be superior to chlorination in terms of microbial quality and chemistry and toxicology. This advantage is particularly evident in effluents that contain appreciable quantities of ammonia-nitrogen or organic nitrogen.     

Toxicity of leather tanning wastewater effluents in sea urchin early development and in marine microalgae

This study was designed to investigate the composition and the toxicity of leather tanning wastewater and conditioned sludge collected at the leather tanning wastewater treatment plant (CODISO) located in Solofra, Avellino (Southern Italy). Samples were analyzed for their conventional parameters (COD, TSS, chromium and ammonia) and for metal content. Effluent samples included raw wastewater, and samples collected following coagulation/flocculation process and biological treatment. A set of toxicity endpoints were tested using sea urchin and marine microalgal bioassays by evaluating acute embryotoxicity, developmental defects, changes in sperm fertilization success and transmissible damage from sperm to the offspring, and changes in algal growth rate. Dose-related toxicity to sea urchin embryogenesis and sperm fertilization success was exerted by effluent or sludge samples according to the following rank: conditioned sludge > coagulated effluent > or = raw influent > effluent from biological treatment. Offspring quality was not affected by sperm exposure to any wastewater or to sludge samples. Algal growth was inhibited by raw or coagulated effluent to a similar extent and, again, the effluent from the biological treatment resulted in a decreased toxicity. The results suggest that coagulated effluent and conditioned sludge result in higher toxicity than raw influent in sea urchin embryos and sperm, whereas the biological wastewater treatment of coagulated effluent, in both sea urchins and algae, cause a substantial improvement of wastewater quality. Hence a final biological wastewater treatment should be operated to minimize any environmental damage from tannery wastewater.     

回用生活污水的电化学消毒试验研究

对北京某中水站回用于杂用水的生活污水进行电化学消毒试验。试验结果表明 ,生活污水经生物接触氧化、活性炭吸附后 ,流经电化学消毒器停留 2 0s、耗电 0 .30kWh/m3 、消毒器出水放置 1h后 ,总大肠菌群数 <3个 /L ,满足生活杂用水的卫生学指标。当余氯浓度及接触时间相等的条件下 ,电化学消毒法的杀菌效果好于加氯消毒。E .coli细胞经电化学消毒和加氯消毒处理后 ,扫描电镜观察的结果表明 :2种方法作用后的细胞在形态上的变化是不相同的 ,说明电化学消毒的消毒机制不仅仅取决于电解产氯的作用 ,还有其他的杀菌作用