Ackee apple (Blighia sapida) seeds: a novel adsorbent for the removal of Congo Red dye from aqueous solutions

The ability of ackee apple (AA) seeds to remove Congo Red (CR) dye from aqueous solution was investigated. AA was characterised using thermo gravimetric analyser, scanning electron microscopy, Braunauer Emmett Teller, pH_pzc, elemental analysis and Boehm titration. The effects of operational parameters such as adsorbent dosage, contact time, initial dye concentration and solution pH were studied in a batch system. pH has a profound influence on the adsorption process. Maximum dye adsorption was observed at pH 3.0. The reaction was fast, reaching equilibrium in 90 min. Adsorption data were best described by Langmuir isotherm and the pseudo-second-order kinetic model with a maximum monolayer coverage of 161.89 mg·g^?1. Both boundary layer and intraparticle diffusion mechanisms were found to govern the adsorption process. Thermodynamic parameters such as standard free energy change (Δ G ⁰), standard enthalpy change (Δ H ⁰), and standard entropy change (Δ S ⁰) were studied. Values of Δ G ⁰ varied between?30.94 and?36.56 kJ·mol^?1, Δ H ⁰ was 25.61 kJ·mol^?1, and Δ S ⁰ was 74.84 kJ·mol^?1·K^?1, indicating that the removal of CR from aqueous solution by AA was spontaneous and endothermic in nature. Regeneration and reusability studies were carried out using different eluents. AA gave the highest adsorption efficiency up to four cycles when treated with 0.3 M HCl. AA was found to be an effective adsorbent for the removal of CR dye from aqueous solution.     

Preconcentration of samarium with modified yeast cells for its determination by atomic emission spectroscopy

A chelating-modified biosorbent is produced by coupling of a dye, procion red, to yeast cells. The resulting modified cells have been characterized by Fourier transform infrared, elemental analysis and thermogravimetric analysis and studied for preconcentration and determination of trace Sm(III). The optimum pH value for sorption of the samarium ions is 6.2. The sorption capacity of functionalized modified yeast cells is 7.2 mg g^?1. Recovery was 99% when Sm(III) was eluted with an aqueous solution of 0.1 mol L^?1 ethylenediaminetetraacetic acid. Scatchard analysis suggested that binding sites were homogeneous. The equilibrium data were analyzed using Langmuir, Freundlich, Temkin, and Redlich–Peterson isotherm models, and the respective constants were determined as 1.0 (L mg^?1), 2.9 [(mg g^?1) (L mg^?1)^1/n], 2.4 × 10⁸ (L g^?1), and 30 (dm³ g^?1) at 20 °C. The method was applied for an Sm(III)-containing sample of ceramic industry effluent.     

Adsorptive features of banana (Musa paradisiaca) stalk-based activated carbon for malachite green dye removal

Chemically prepared activated carbon derived from banana stalk (BSAC) was used as an adsorbent to remove malachite green (MG) dye from aqueous solution. BSAC was characterised using thermogravimetric analyser, Brunauer Emmett Teller, Fourier transform infrared spectrometry, scanning electron microscopy, pH_pzc, elemental analysis and Boehm titration. The effectiveness of BSAC in adsorbing MG dye was studied as a function of pH, contact time, temperature, initial dye concentration and repeated desorption–adsorption processes. pH_pzc of BSAC was 4.5 and maximum dye adsorption occurred at pH 8.0. The rate of dye adsorption by BSAC was very fast initially, attaining equilibrium within 120 min following a pseudo-second-order kinetic model. Experimental data were analysed by Langmuir, Freundlich and Dubinin–Raduschevich isotherms. Equilibrium data fitted best into the Langmuir model, with a maximum adsorption capacity of 141.76 mg·g^?1. Δ G ⁰ values were negative, indicating that the process of MG dye adsorption onto BSAC was spontaneous. The positive values of Δ H ⁰ and Δ S ⁰ suggests that the process of dye adsorption was endothermic. The regeneration efficiency of spent BSAC was studied using 0.5 M HCl, and was found to be in the range of 90.22–95.16% after four cycles. This adsorbent was found to be both effective and viable for the removal of MG dye from aqueous solution.     

Pomegranate husk as an adsorbent in the removal of toxic chromium from wastewater

The use of a new sorbent developed from the husk of pomegranate, a famous fruit in Egypt, for the removal of toxic chromium from aqueous solution has been investigated. The batch experiment was conducted to determine the adsorption capacity of the pomegranate husk. The effects of initial metal concentration (25 and 50 mg l^?1), pH, contact time, and sorbent concentration (2–6 g l^?1) have been studied at room temperature. A strong dependence of the adsorption capacity on pH was observed, the capacity increased as the pH decreased, and the optimum pH value was pH 1.0. Adsorption equilibrium and kinetics were studied with different sorbent and metal concentrations. The adsorption process was fast, and equilibrium was reached within 3 h. The maximum removal was 100% for 25 mg l^?1 of Cr⁶⁺ concentration on 5 g l^?1 pomegranate husk concentration, and the maximum adsorption capacity was 10.59 mg g^?1. The kinetic data were analysed using various kinetic models—pseudo-first-order, pseudo-second-order, Elovich, and intraparticle diffusion equations—and the equilibrium data were tested using several isotherm models, Langmuir, Freundlich, Tempkin, Dubinin–Radushkevich, and Generalized isotherm equations. The Elovich and pseudo-second-order equations provided the greatest accuracy for the kinetic data, while Langmuir and Generalized isotherm models were the closest fit for the equilibrium data. The activation energy of sorption has also been evaluated as 0.236 and 0.707 kJ mol^?1 for 25 and 50 mg l^?1 chromium concentration, respectively.     

Adsorptive removal of rhodamine B from textile wastewater using water chestnut (Trapa natans L.) peel: adsorption dynamics and kinetic studies

Water chestnut peel, an agricultural bio-waste, was used as a biosorbent for removal of rhodamine B (RhB), basic textile dye, from an aqueous solution. The effects of various experimental parameters were studied. The equilibrium data correlated well with a Freundlich isotherm (R² = 0.98–0.99) followed by a Halsey isotherm model (R² = 0.98–0.99) which indicated heterogeneity of the adsorbent surface and multilayer adsorption of RhB dye onto the water chestnut peel waste (WCPW). High correlation coefficients (R² = 0.99) together with close agreement between experimental q_e (0.4–1.7 mg g^?1) and calculated q_e (0.4–2.5 mg g^?1) suggested that the adsorption process followed pseudo-second-order kinetics, with k₂ values in the range of 52–3.4 × 10^?1 g mg^?1 min^?1 at different concentrations. The overall mechanism of adsorption was controlled by both liquid-film and intra-particle diffusions. The negative values of change in Gibb's free energy (?ΔG⁰ = 19.2–29.2 kJ mol^?1) and positive values of change in enthalpy (ΔH⁰ = 30.9–117.6 kJ mol^?1) revealed the process to be spontaneous and endothermic. WCPW was found to be an effective adsorbent for removal of RhB, a cationic dye, from an aqueous solution.     

Kinetic and mechanism studies of the adsorption of lead onto waste cow bone powder (WCBP) surfaces

This study examines the adsorption isotherms, kinetics and mechanisms of Pb²⁺ sorption onto waste cow bone powder (WCBP) surfaces. The concentrations of Pb²⁺ in the study range from 10 to 90 mg/L. Although the sorption data follow the Langmuir and Freundlich isotherm, a detailed examination reveals that surface sorption or complexation and co-precipitation are the most important mechanisms, along with possibly ion exchange and solid diffusion also contributing to the overall sorption process. The co-precipitation of Pb²⁺ with the calcium hydroxyapatite (Ca-HAP) is implied by significant changes in Ca²⁺ and PO₄ ^3? concentrations during the metal sorption processes. The Pb²⁺ sorption onto the WCBP surface by metal complexation with surface functional groups such as ≡ POH. The major metal surface species are likely to be ≡ POPb⁺. The sorption isotherm results indicated that Pb²⁺ sorption onto the Langmuir and Freundlich constant q _max and K _F is 9.52 and 8.18 mg g^?1, respectively. Sorption kinetics results indicated that Pb²⁺ sorption onto WCBP was pseudo-second-order rate constants K ₂ was 1.12 g mg^?1 h^?1. The main mechanism is adsorption or surface complexation (≡POPb⁺: 61.6%), co-precipitation or ion exchange [Ca_3.93 Pb_1.07 (PO₄)₃ (OH): 21.4%] and other precipitation [Pb 50 mg L^?1 and natural pH: 17%). Sorption isotherms showed that WCBP has a much higher Pb²⁺ removal rate in an aqueous solution; the greater capability of WCBP to remove aqueous Pb²⁺ indicates its potential as another promising way to remediate Pb²⁺-contaminated media.     

Biosolids application affects the competitive sorption and lability of cadmium,copper, nickel,lead, and zinc in fluvial and calcareous soils

The objective of this research was to investigate the effects of biosolids on the competitive sorption and lability of the sorbed Cd, Cu, Ni, Pb, and Zn in fluvial and calcareous soils. Competitive sorption isotherms were developed, and the lability of these metals was estimated by DTPA extraction following their sorption. Sorption of all metals was higher in the fluvial than in the calcareous soil. Sorption of Cu and Pb was stronger than that of Cd, Ni, and Zn in all soils. Biosolids application (2.5%) reduced the sorption of all metals especially Cu and Pb (28–43%) in both soils (especially the calcareous soil) at the lower added metal concentrations (50 and 100 mg L^?1). However, it increased the sorption of all metals especially Pb and Cu in both soils (especially the calcareous soil; 15.5-fold for Cu) at the higher added concentrations (250 and 300 mg L^?1). Nickel showed the highest lability followed by Cd, Zn, and Pb in both soils. Biosolids increased the lability of the sorbed Ni in the fluvial soils at all added concentrations and the lability of Cd, Pb, and Zn at 50 mg L^?1, but decreased the lability of Cd, Pb, and Zn at 250 and 300 mg L^?1 in both soils. We conclude that at low loading rate (e.g., 50 mg L^?1) biosolids treatment might increase the lability and environmental risk of Cd, Cu, Pb, and Zn. However, at high loading rate (e.g., 300 mg L^?1) biosolids may be used as an immobilizing agent for Cd, Cu, Pb, Zn and mobilizing agent for Ni.     

Chemically modified biochar produced from conocarpus waste increases NO<Subscript>3</Subscript> removal from aqueous solutions

Biochar has emerged as a universal sorbent for the removal of contaminants from water and soil. However, its efficiency is lower than that of commercially available sorbents. Engineering biochar by chemical modification may improve its sorption efficiency. In this study, conocarpus green waste was chemically modified with magnesium and iron oxides and then subjected to thermal pyrolysis to produce biochar. These chemically modified biochars were tested for NO₃ removal efficiency from aqueous solutions in batch sorption isothermal and kinetic experiments. The results revealed that MgO-biochar outperformed other biochars with a maximum NO₃ sorption capacity of 45.36 mmol kg^?1 predicted by the Langmuir sorption model. The kinetics data were well described by the Type 1 pseudo-second-order model, indicating chemisorption as the dominating mechanism of NO₃ sorption onto biochars. Greater efficiency of MgO-biochar was related to its high specific surface area (391.8 m² g^?1) and formation of strong ionic complexes with NO₃. At an initial pH of 2, more than 89 % NO₃ removal efficiency was observed for all of the biochars. We conclude that chemical modification can alter the surface chemistry of biochar, thereby leading to enhanced sorption capacity compared with simple biochar.     

Quantitative analysis and sorption of cadmium in environmental samples with a functionalized synthetic polymer

Quantitative analysis of cadmium in environmental samples was achieved with a polymeric sorbent synthesized by copolymerization of N,N-dimethylacrylamide and allyl glycidyl ether/iminodiacetic acid as chelating monomers with N,N′-methylenebisacrylamide as cross-linker. The polymer was characterized by Fourier transform infrared spectroscopy, thermogravimetric analysis, elemental analysis, and scanning electron microscopy. The sorption capacity of the functionalized sorbent was 70 mg g^?1. The equilibrium sorption data of Cd(II) on polymeric sorbent were analyzed using Langmuir, Freundlich, Temkin, and Redlich–Peterson models. Based on equilibrium adsorption data, the constants at pH 4.2 and 20 °C were determined for the first three as 0.33 (L mg^?1), 17.5 (mg g^?1) (L mg^?1)^1/n, and 12.9 (J mol^?1). Recovery of 94% of the metal ion was obtained with 0.5 mol L^?1 nitric acid as an eluting agent.     

Kinetic,equilibrium and thermodynamic studies for the sorption of metribuzin from aqueous solution using banana peels,an agro-based biomass

Banana peels were employed for the removal of metribuzin from aqueous solution. Sorption in the batch mode was optimized regarding pH, contact time, sorbent dose, initial pesticide concentrations, and temperature. The sorption data were fitted to pseudo-first-order, pseudo-second-order, intraparticle diffusion, Elovich, and liquid film diffusion model, the pseudo-second-order exhibiting best fit (R² = 0.9803). Of the four most common sorption isotherm models (Langmuir, Freundlich, Tempkin, and Dubinin–Radushkevich), the data followed the Langmuir isotherm with highest correlation. The maximum adsorption capacity was found to be 167 mg g^?1. Gibbs free energy, enthalpy, and entropy showed that the sorption was exothermic and spontaneous.     

Trichoderma harzianum: a green sorbent for Pb(II) uptake from aqueous solutions

This investigation describes the use of specially cultivated, nonliving biomass of Trichoderma harzianum as a biosorbent for the batch removal of Pb(II) from a stirred system under different experimental conditions. The metal removal depended upon pH, sorbent particle size, initial Pb(II) concentration, shaking speed, and sorption time. The optimal experimental conditions for the removal of Pb(II) by T. harzianum with an initial metal concentration of 100 mg L^?1 were obtained at a particle size of 53 μm, a pH of 4.5, a shaking speed of 200 rpm, and a contact time of 720 min. The results were analyzed in terms of adsorption isotherms and kinetic models. The Freundlich isotherm model and pseudo second-order model fitted well in the data. T. harzianum proved to be a good biomaterial for accumulating Pb(II) from aqueous solutions (q = 460 mg g^?1).     

The removal of arsenic from water with natural and modified clinoptilolite

The presence of increased arsenic concentrations in Eastern Croatia is a consequence of the geological composition of the soil. Because of its known harmful effects, arsenic removal is of high importance and adsorption represents an attractive and economically efficient approach to arsenic removal. The use of zeolites obtained from the Donje Jesenje deposit, Croatia (CZ) and the Zlatokop deposit in Vranjska Banja, Serbia (SZ) in Na- and Fe–Na-modified forms was investigated in order to effectively remove arsenate and arsenite from aqueous solutions. The adsorption kinetics of arsenic was studied as a function of the initial arsenate and arsenite concentrations (30–300 μg · L^?1), equilibration time (3–48 h), pH (5–10) and in the presence of sulfate and phosphate at initial concentrations of 0.2–0.5 mg · L^?1. In order to estimate sorption constants designating the sorption capacity and affinity of the zeolites samples, the experimental results were fitted to the Langmuir and Freundlich sorption isotherms. Desorption tests conducted with 1–3 mol · L^?1 HCl indicated that arsenate sorption was irreversible. The results obtained indicated that use of the Serbian zeolite in the Fe–Na-modified form (Fe–Na-SZ) was favourable for arsenate removal from water containing up to 30 μg As · L^?1.     

Assessment of PAHs in water and fish tissues from Great Bitter and El Temsah lakes,Suez Canal,as chemical markers of pollution sources

Sea water and fish tissue samples were collected from nine sampling stations from the Great Bitter and El Temsah lakes in the Suez Canal and analysed for polycyclic aromatic hydrocarbon (PAH). The compositions of PAH determined in the dissolved fraction of sea water were measured in order to use them as chemical markers for identifying different sources of PAH pollution in this region. PAHs determined in fish tissues were measured for comparison with human health standards as consumption. The total mean PAHs concentrations in the sea water samples ranged from 0.28 to 39.57 μg l^?1 with an overall mean of 10.78 and 12.38 μg l^?1 for El Temsah and Bitter Lakes water, respectively. Total PAHs fractions recorded in muscle tissues of all different Osteicthyes fishes collected from Great Bitter lakes ranged from 5.8 to 218.5 μg g^?1 with an overall mean of 57.98 μg g^?1 during all seasons. However, they ranged from 68 to 623 μg g^?1 with an overall mean of 87.69 μg g^?1 recorded in El Temsah lake during four seasons (2003–2004). Benzo(a)pyrene was the most dominant PAHs found in the sea water samples from both lakes with an average concentration of 3.8 μ g l^?1. Dibenzo(a,h)anthracene (DBA) was the most dominant PAHs recorded in fish samples. A maximum of 533 μg g^?1 of DBA was recorded in Dahbana sp. collected from Bitter lakes during January 2004. However, a maximum of 68.7 μ g g^?1 was recorded in Liza carinata species collected from El Temsah lake during July, 2004. The simultaneous occurrence of isomer ratios PHE/ANT<10 for all stations indicated that the major PAH input to water was from combustion of fossil fuel (pyrolytic source). The average ratios were 1.21 and 12.9 during winter (January 2004) and 4.3 and 8.63 during spring (April 2004) for all water samples of Great Bitter lakes and El Temsah lake, respectively. In addition, the present data demonstrate that PAHs from fossil fuel sources (MW<178) were the least significant source of PAHs in this region.     

Removal of heavy metals from aqueous solutions using activated carbon prepared from Cicer arietinum

Removal of Cu²⁺, Cd²⁺, Pb²⁺, and Zn²⁺ from aqueous solutions by activated carbon prepared from stems and seed hulls of Cicer arietinum, an agricultural solid waste, has been studied. The influence of various parameters, such as pH, contact time, adsorbent dose, and initial concentration of metal ions on removal was evaluated. The activated carbon was characterized by FT-IR spectroscopy, X-ray diffraction, and elemental analysis. Sorption isotherms were studied using Langmuir and Freundlich isotherm models. All experimental sorption data were fitted to the sorption models using nonlinear least-squares regression. The maximum adsorption capacity values for activated carbon prepared from Cicer arietinum waste for metal ions were 18 mg g^?1 (Cu²⁺), 18 mg g^?1 (Cd²⁺), 20 mg g^?1 (Pb²⁺), and 20 mg g^?1 (Zn²⁺), respectively. The Freundlich isotherm model fit was best, followed by the pseudo-second-order kinetic model. Desorption studies were carried out with dilute hydrochloric acid for quantitative recovery of the metal ions and for regeneration of the adsorbent.     

Decolorization and degradation of acid dyes mediated by salt fractionated turnip ( Brassica rapa ) peroxidases

Peroxidases from turnip roots (524?U?g^?1 of vegetable) were highly effective in decolorizing acid dyes having wide spectrum chemical groups. Dye solutions, containing 40–170?mg?dye?L^?1, were treated by turnip peroxidases (TP) (specific activity of 122.0?U?mg^?1 proteins). These enzymes were able to decolorize most of the acid dyes in the presence of 2.0?mM 1-hydroxybenzotriazole (HOBT). Increasing concentration of enzyme and time in the absence of HOBT did not influence dye decolorization. The rate of decolorization was significantly enhanced when HOBT was added to the decolorizing solutions. The decolorization of all the used dyes was maximum at pH 5.0 and 40°C. Complex mixtures of dyes were significantly decolorized when treated with enzyme in the presence of HOBT (2.0?mM). Phytotoxicity test based on Allium cepa root growth inhibition has shown that majority of the TP-treated dye product were not more toxic than their parent dye. Kinetic parameters of the TP with various dyes showed that this enzyme has highest affinity for Acid Yellow 42. This study demonstrates that the peroxidase/mediator system was an effective biocatalyst for the treatment of industrial effluents from textile, dye manufacturing, dyeing and printing industries or complex mixtures of dyes.     

Effect of waterborne boron and molybdenum on survival,growth and feed intake of Indian major carp,Cirrhinus mrigala (Hamilton)

The effect of either boron (B) or molybdenum (Mo) on survival, growth and feed intake of Indian major carp, Cirrhinus mrigala (Hamilton), advanced fry was studied in two separate experiments. Survival rates of C. mrigala fry (2.78±0.14 g) following 50 days’ exposure to B at 0.01 (control), 0.5, 1.0, 2.0, 4.0 and 8.0 mg·L ^?1 were 100% at all concentrations except 8.0 mg·L ^?1 where the survival rate 87.5±7.5%. We observed 100% survival of mrigala fry at all concentrations of Mo, 0.02 (control), 0.5, 1.0, 2.0, 4.0 and 8.0 mg·L ^?1. Both B and Mo at 0.5 mg·L ^?1 showed significantly (p<0.05) higher growth of the fish compared with control and other concentrations. B exposure at 1.0, 2.0 and 4.0 mg·L ^?1 had no significant effect on growth rate, whereas at 8.0 mg B·L ^?1 growth of the fish almost ceased. Mo exposure at 1.0, 2.0, 4.0 and 8.0 mg·L ^?1 caused no significant effect on growth rate of the fish compared to control. Both B and Mo at all concentrations had no significant effect on feed intake of the fish compared with control, except at the highest concentration of boron (8.0 mg·L ^?1).     

The influence of solid matrices on arsenic toxicity to Corophium orientale

In marine ecosystems, benthic organisms are really important because they are the first step in the transfer of contaminants from environment to biota. To this end, this study focused on biological assays with the amphipod Corophium orientale exposed to two different molecules of arsenic: arsenate (As^V), the most abundant form in sediments, and dimethyl-arsinate (DMA), expected to be moderately toxic as an intermediate in the process of detoxification. The toxicity of arsenic compounds was measured after exposure to three different matrices: water, spiked natural sediment and inert spiked quartz sand. LC₅₀ values were calculated for each exposure, and the results confirmed the highest toxicity of As^V, in addition to underlining the importance of matrix of exposure. Water exposure was the matrix which presented the highest toxicity for inorganic arsenic (As^V LC₅₀=3.51 mg L^?1 vs DMA LC₅₀=54.65 mg L^?1), spiked natural sediment demonstrated its capability to chelate arsenate toxicity (As^V LC₅₀=34.27 mg kg^?1 vs. DMA LC₅₀=52.19 mg kg^?1) and spiked quartz sand presented intermediate values for As^V (LC₅₀=25.26 mg kg^?1), whereas for DMA a lower toxicity was registered (LC₅₀=872.35 mg kg^?1). This study can provide some useful data linked with chemical speciation of arsenic and exposure matrix, for improving the correct management of contaminated sediment.     

Organochlorine pesticides (HCHs and DDTs) in soils along the north coastal areas of the Bohai Sea,China

A systematic survey of organochlorine pesticides (OCPs) including hexachlorocyclohexane isomers (α-HCH, β-HCH, γ-HCH, δ-HCH and ΣHCH) and dichlorodiphenyltrichloroethane metabolites (p,p′-DDT, p,p′-DDE, o,p′-DDT, p,p′-DDD and ∑DDT) in soils along the north coastal areas of the Bohai Sea, China, has been lacking. In this study, 31 representative surface soil samples were collected along the north coastal and riverine areas of the Bohai Sea to characterise the potential for adverse effects of ∑HCH, ∑DDT and their individual isomers and transformation products. Concentrations of ΣHCH and ΣDDT in soils ranged from less than the limit of detection (1 ng · g^?1 dw (mean: 3.5 ng · g^?1 dw) and2 ng · g^?1 dw (mean: 1.7 × 10¹ ng · g^?1 dw), respectively. Compared with studies of OCPs in soils from other locations, concentrations of HCHs and DDTs observed in this study were moderate. Concentrations of OCPs observed in soils were generally less than proposed reference values. HCH residues were a mixture of historical technical HCH and current lindane sources. The pattern of DDTs was consistent with historical releases of technical DDTs. Selected soil physicochemical properties did not explain the sorption and/or partitioning of HCHs or DDTs.     

Biosorption of Direct Yellow 12 from aqueous solution using green alga Ulva lactuca

The potential of commonly available green alga Ulva lactuca was investigated as viable biomaterials for removal of synthetic azo dye (Direct Yellow 12, DY-12) from aqueous solution. The results obtained from the batch experiments revealed that the ability of the U. lactuca to remove DY-12 from its aqueous solution was dependent on the dye concentration, pH, and algal biomass but less dependent on the particle size of the U. lactuca. The equilibrium conditions and kinetics of adsorption were investigated, and the adsorption kinetic was consistent with the pseudo-second-order model (R ²=1). The adsorption isotherm followed only the Freundlich model with a correlation coefficient R ²=0.99. This study demonstrated that the U. lactuca could be used as an effective biosorbent for the removal of DY-12 from its aqueous solution.     

Assessment of heavy metals in a soil contaminated by oil spill: a case study in Nigeria

Surface and subsurface soil samples contaminated with crude oils were collected from an impacted site at Bodo City in the Niger Delta, Nigeria, after a field reconnaissance survey. An uncontaminated soil sample collected 100 m from the impacted site, but within the same geographical area, was used as a control. Trace elements such as, As, Cu, Cr, Cd, Fe, Pb, Ba, Ni, V, Hg and cation-exchange capacity constituents of the contaminated and uncontaminated soils were determined by atomic absorption spectroscopy. Trace element concentrations were: Cu, 0.5–13.4 mg kg^{? 1}; Cr, 0.2–0.8 mg kg^{? 1}; Fe, 6.2–8.7 mg kg^{? 1}; Ba 80.0–108.0 mg kg^{? 1}; Ni, 0.6–4.8 mg kg^{? 1}; and V, 4.0–9.4 mg kg^{? 1}; cation-exchange capacity ranged from 43.6 to 57.2 mg kg^{? 1} in surface and subsurface soils. Results showed that eigenvalues for the two first principal components represent up to 49% of the total variance. A positive correlation of the first principal component with Cu, Cr and cation-exchange capacity shows pollution from oil spillage, while a positive correlation of the second principal component with Cr, Fe, V, and dissolved oxygen (DO) shows both oil pollution and allochthonous inputs.