Investigation of PM2.5 and carbon dioxide levels in urban homes

PM_2.5 (particulate matter with an aerodynamic diameter <2.5 μm) samples were collected in the indoor environments of 15 urban homes and their adjacent outdoor environments in Alexandria, Egypt, during the spring time. Indoor and outdoor carbon dioxide (CO₂) levels were also measured concurrently. The results showed that indoor and outdoor PM_2.5 concentrations in the 15 sites, with daily averages of 45.5 ± 11.1 and 47.3 ± 12.9 µg/m³, respectively, were significantly higher than the ambient 24-hr PM_2.5 standard of 35 µg/m³ recommended by the U.S. Environmental Protection Agency (EPA). The indoor PM_2.5 and CO₂ levels were correlated with the corresponding outdoor levels, demonstrating that outdoor convection and infiltration could lead to direct transportation indoors. Ventilation rates were also measured in the selected residences and ranged from 1.6 to 4.5 hr^?1 with median value of 3.3 hr^?1. The indoor/outdoor (I/O) ratios of the monitored homes varied from 0.73 to 1.65 with average value of 0.99 ± 0.26 for PM_2.5, whereas those for CO₂ ranged from 1.13 to 1.66 with average value of 1.41 ± 0.15. Indoor sources and personal activities, including smoking and cooking, were found to significantly influence indoor levels.

Implications: Few studies on indoor air quality were carried out in Egypt, and the scarce data resulted from such studies do not allow accurate assessment of the current situation to take necessary preventive actions. The current research investigates indoor levels of PM_2.5 and CO₂ in a number of homes located in the city of Alexandria as well as the potential contribution from both indoor and outdoor sources. The study draws attention of policymakers to the importance of the establishment of national indoor air quality standards to protect human health and control air pollution in different indoor environments.     

Indoor particulate matter in urban residences of Alexandria,Egypt

Indoor particulate matter samples were collected in 17 homes in an urban area in Alexandria during the summer season. During air measurement in all selected homes, parallel outdoor air samples were taken in the balconies of the domestic residences. It was found that the mean indoor PM_2.5 and PM₁₀ (particulate matter with an aerodynamic diameter ≤2.5 and ≤10 μm, respectively) concentrations were 53.5 ± 15.2 and 77.2 ± 15.1 µg/m³, respectively. The corresponding mean outdoor levels were 66.2 ± 16.5 and 123.8 ± 32.1 µg/m³, respectively. PM_2.5 concentrations accounted, on average, for 68.8 ± 12.8% of the total PM₁₀ concentrations indoors, whereas PM_2.5 contributed to 53.7 ± 4.9% of the total outdoor PM₁₀ concentrations. The median indoor/outdoor mass concentration (I/O) ratios were 0.81 (range: 0.43–1.45) and 0.65 (range: 0.4–1.07) for PM_2.5 and PM₁₀, respectively. Only four homes were found with I/O ratios above 1, indicating significant contribution from indoor sources. Poor correlation was seen between the indoor PM₁₀ and PM_2.5 levels and the corresponding outdoor concentrations. PM₁₀ levels were significantly correlated with PM_2.5 loadings indoors and outdoors and this might be related to PM₁₀ and PM_2.5 originating from similar particulate matter emission sources. Smoking, cooking using gas stoves, and cleaning were the major indoor sources contributed to elevated indoor levels of PM₁₀ and PM_2.5.

Implications: The current study presents results of the first PM_2.5 and PM₁₀ study in homes located in the city of Alexandria, Egypt. Scarce data are available on indoor air quality in Egypt. Poor correlation was seen between the indoor and outdoor particulate matter concentrations. Indoor sources such as smoking, cooking, and cleaning were found to be the major contributors to elevated indoor levels of PM₁₀ and PM_2.5.     

PM2.5, soot and NO2 indoor–outdoor relationships at homes,pre-schools and schools in Stockholm,Sweden

In developed nations people spend about 90% of their time indoors. The relationship between indoor and outdoor air pollution levels is important for the understanding of the health effects of outdoor air pollution. Although other studies describe both the outdoor and indoor atmospheric environment, few excluded a priori major indoor sources, measured the air exchange rate, included more than one micro-environment and included the presence of human activity. PM_2.5, soot, NO₂ and the air exchange rate were measured during winter and summer indoors and outdoors at 18 homes (mostly apartments) of 18 children (6–11-years-old) and also at the six schools and 10 pre-schools that the children attended. The three types of indoor environments were free of environmental tobacco smoke and gas appliances, as the aim was to asses to what extent PM_2.5, soot and NO₂ infiltrate from outdoors to indoors. The median indoor and outdoor PM_2.5 levels were 8.4 μg m^?3 and 9.3 μg m^?3, respectively. The median indoor levels for soot and NO₂ were 0.66 m^?1 × 10^?5 and 10.0 μg m^?3, respectively. The respective outdoor levels were 0.96 m^?1 × 10^?5 and 12.4 μg m^?3. The median indoor/outdoor (I/O) ratios were 0.93, 0.76 and 0.92 for PM_2.5, soot and NO₂, respectively. Their infiltration factors were influenced by the micro-environment, ventilation type and air exchange rate, with aggregated values of 0.25, 0.55 and 0.64, respectively. Indoor and outdoor NO₂ levels were strongly associated (R² = 0.71), followed by soot (R² = 0.50) and PM_2.5 (R² = 0.16). In Stockholm, the three major indoor environments occupied by children offer little protection against combustion-related particles and gases in the outdoor air. Outdoor PM_2.5 seems to infiltrate less, but indoor sources compensate.     

Effect of Gas and Kerosene Space Heaters on Indoor Air Quality: A Study in Homes of Santiago,Chile

Abstract

The impact of outdoor and indoor pollution sources on indoor air quality in Santiago, Chile was investigated. Toward this end, 16 homes were sampled in four sessions. Each session included an outdoor site and four homes using different unvented space heaters (electric or central heating, compressed natural gas, liquefied petroleum gas, and kerosene). Average outdoor fine particulate matter (PM_2.5) concentrations were very high (55.9 μg·m^-3), and a large fraction of these particles penetrated indoors. PM_2.5 and several PM_2.5 components (including sulfate, elemental carbon, organic carbon, metals, and polycyclic aromatic hydrocarbons) were elevated in homes using kerosene heaters. Nitrogen dioxide (NO₂) and ultrafine particles (UFPs) were higher in homes with combustion heaters as compared with those with electric heaters or central heating. A regression model was used to assess the effect of heater use on continuous indoor PM_2.5 concentrations when windows were closed. The model found an impact only for kerosene heaters (45.8 μg m^-3).     

The Influences of Ambient Particle Composition and Size on Particle Infiltration in Los Angeles,CA, Residences

Abstract

Particle infiltration is a key determinant of the indoor concentrations of ambient particles. Few studies have examined the influence of particle composition on infiltration, particularly in areas with high concentrations of volatile particles, such as ammonium nitrate (NH₄NO₃). A comprehensive indoor monitoring study was conducted in 17 Los Angeles–area homes. As part of this study, indoor/outdoor concentration ratios during overnight (nonindoor source) periods were used to estimate the fraction of ambient particles remaining airborne indoors, or the particle infiltration factor (F_INF), for fine particles (PM_2.5), its nonvolatile (i.e., black carbon [BC]) and volatile (i.e., nitrate [NO₃ ^?]) components, and particle sizes ranging between 0.02 and 10 μm. F_INF was highest for BC (median = 0.84) and lowest for NO₃ ^? (median = 0.18). The low F_INF for NO₃ ^? was likely because of volatilization of NO₃ ^? particles once indoors, in addition to depositional losses upon building entry. The F_INF for PM_2.5 (median = 0.48) fell between those for BC and NO₃ ^?, reflecting the contributions of both particle components to PM_2.5. F_INF varied with particle size, air-exchange rate, and outdoor NO₃ ^? concentrations. The F_INF for particles between 0.7 and 2 μm in size was considerably lower during periods of high as compared with low outdoor NO₃ ^? concentrations, suggesting that outdoor NO₃ ^? particles were of this size. This study demonstrates that infiltration of PM_2.5 varies by particle component and is lowest for volatile species, such as NH₄NO₃. Our results suggest that volatile particle components may influence the ability for outdoor PM concentrations to represent indoor and, thus, personal exposures to particles of ambient origin, because volatilization of these particles causes the composition of PM_2.5 to differ indoors and outdoors. Consequently, particle composition likely influences observed epidemiologic relationships based on outdoor PM concentrations, especially in areas with high concentrations of NH₄NO₃ and other volatile particles.     

Indoor particle size distributions in homes with open fires and improved Patsari cook stoves

Particulate pollution has been clearly linked with adverse health impacts from open fire cookstoves, and indoor air concentrations are frequently used as a proxy for exposures in health studies. Implicit are the assumptions that the size distributions for the open fire and improved stove are not significantly different, and that the relationship between indoor concentrations and personal exposures is the same between stoves. To evaluate the impact of these assumptions size distributions of particulate matter in indoor air were measured with the Sioutas cascade impactor in homes using open fires and improved Patsari stoves in a rural Purepecha community in Michoacan, Mexico. On average indoor concentrations of particles less than 0.25 μm were 72% reduced in homes with improved Patsari stoves, reflecting a reduced contribution of this size fraction to PM_2.5 mass concentrations from 68% to 48%. As a result the mass median diameter of indoor PM_2.5 particulate matter was increased by 29% with the Patsari improved stove compared to the open fire (from 0.42 μm to 0.59 μm, respectively). Personal PM_2.5 exposure concentrations for women in homes using open fires were approximately 61% of indoor concentration levels (156 μg m^?3 and 257 μg m^?3 respectively). In contrast personal exposure concentrations were 77% times indoor air concentration levels for women in homes using improved Patsari stoves (78 μg m^?3and 101 μg m^?3 respectively). Thus, if indoor air concentrations are used in health and epidemiologic studies significant bias may result if the shift in size distribution and the change in relationship between indoor air concentrations and personal exposure concentrations are not accounted for between different stove types.     

Day-to-Day Particulate Exposures and Health Changes in Los Angeles Area Residents with Severe Lung Disease

ABSTRACT

We measured particulate matter (PM_2.5 and PM₁₀) exposures, home temperature, arterial blood oxygen saturation, blood pressure, and lung function in 30 volunteer Los Angeles area residents during four-day intervals. Continuous Holter electrocardiograms were recorded in a subgroup on the first two days. Subjects recorded symptoms and time-activity patterns in diaries during monitoring, and during a reference period one week earlier/later. All subjects had severe chronic obstructive pulmonary disease. PM₁₀ (24-hr mean) at monitoring stations near subjects’ homes averaged 33 μg/m³, and ranged from 9 to 84 μpg/m³. In longitudinal analyses, day-to-day changes in PM_2.5 and PM₁₀ outside subjects’ homes significantly tracked concurrent station PM10 (r² = 0.22 and 0.44, respectively). Indoor and personal concentrations were less related to station readings (r² ≤ 0.1), but tracked each other (r² ≥ 0.4). In-home temperatures tracked outdoor temperatures more for lows (r² = 0.27) than for highs (r² = 0.10). These longitudinal relationships of subject-oriented and station PM measurements were generally similar to cross-sectional relationships observed previously in similar subjects. Among health measurements, only blood pressure showed reasonably consistent unfavorable longitudinal associations with particulates, more with station or outdoor PM than with indoor or personal PM.     

Evaluation of Human Exposure to Ambient PM10 in the Metropolitan Area of Mexico City Using a GIS-Based Methodology

ABSTRACT

The main goal of this study was to evaluate the magnitude of outdoor exposure to fine particulate matter (PM₁₀) potentially experienced by the population of metropolitan Mexico City. With the use of a geographic information system (GIS), spatially resolved PM₁₀ distributions were generated and linked to the local population. The PM₁₀ concentration exceeded the 24-hr air quality standard of 150 μg/m³ on 16% of the days, and the annual air quality standard of 50 μg/m³ was exceeded by almost twice its value in some places. The basic methodology described in this paper integrates spatial demographic and air quality databases, allowing the evaluation of various air pollution reduction scenarios. Achieving the annual air quality standard would represent a reduction in the annual arithmetic average concentration of 14 μg/m³ for the typical inhabitant. Human exposure to particulate matter (PM) has been associated with mortality and morbidity in Mexico City; reducing the concentration levels of this pollutant would represent a reduction in mortality and morbidity and the associated cost of such impacts. This methodology is critical to assessing the potential benefits of the current initiative to improve air quality implemented by the Environmental Metropolitan Commission of Mexico City.     

Evaluation of airborne particulate matter and metals data in personal,indoor and outdoor environments using ED-XRF and ICP-MS and co-located duplicate samples

Factors and sources affecting measurement uncertainty associated with monitoring metals in airborne particulate matter (PM) were investigated as part of the Windsor, Ontario Exposure Assessment Study (WOEAS). The assessment was made using co-located duplicate samples and a comparison of two analytical approaches: ED-XRF and ICP-MS. Sampling variability was estimated using relative percent difference (RPD) of co-located duplicate samples. The comparison of ICP-MS and ED-XRF results yields very good correlations (R² ≥ 0.7) for elements present at concentrations that pass both ICP-MS and ED-XRF detection limits (e.g. Fe, Mn, Zn, Pb and Cu). PM concentration ranges (median, sample number) of 24-h indoor PM₁₀ and personal PM₁₀ filters, and outdoor PM_2.5 filters were determined to be 2.2–40.7 (11.0, n = 48) μg m^?3, 8.0–48.3 (11.9, n = 48) μg m^?3, and 17.1–42.3 (21.6, n = 18) μg m^?3, respectively. The gravimetric analytical results reveal that the variations in PM mass measurements for same-day sampling are insignificant compared to temporal or spatial variations: 92%, 100% and 96% of indoor, outdoor and personal duplicate samples, respectively, pass the quality criteria (RPD ≤ 20%). Uncertainties associated with ED-XRF elemental measurements of S, Ca, Mn, Fe and Zn for 24-h filter samples are low: 78%–100% of the duplicate samples passed the quality criteria. In the case of 24-h filter samples using ICP-MS, more elements passed the quality criteria due to the lower detection limits. These were: Li, Na, K, Ca, Si, Al, V, Fe, Mn, Co, Cu, Mo, Ag, Zn, Pb, As, Mg, Sb, Sn, Sr, Th, Ti, Tl, and U. Low air concentrations of metals (near or below instrumental detection limits) and/or inadvertent introduction of metal contamination are the main causes for excluding elements based on the pass/fail criteria. Uncertainty associated with elemental measurements must be assessed on an element-by-element basis.     

Outdoor and indoor factors influencing particulate matter and carbon dioxide levels in naturally ventilated urban homes

ABSTRACT

The present study investigated indoor and outdoor concentrations of two particulate matter size fractions (PM₁₀ and PM_2.5) and CO₂ in 20 urban homes ventilated naturally and located in one congested residential and commercial area in the city of Alexandria, Egypt. The results indicate that the daily mean PM_2.5 concentrations measured in the ambient air, living rooms, and kitchens of all sampling sites exceeded the WHO guideline by 100%, 65%, and 95%, respectively. The daily mean outdoor and indoor PM₁₀ levels in all sampling sites were found to exceed the WHO guideline by 100% and 80%, respectively. The indoor PM₁₀ and PM_2.5 concentrations were significantly correlated with their corresponding outdoor levels, as natural ventilation through opening doors and windows allowed direct transfer of outdoor airborne particles into the indoor air. Most of the kitchens investigated had higher indoor concentrations of PM_2.5 and CO₂ than in living rooms. The elevated levels of PM_2.5 and CO₂ in domestic kitchens were probably related to inadequate ventilation. The current study attempted to understand the sources and the various indoor and outdoor factors that affect indoor PM₁₀, PM_2.5 and CO₂ concentrations. Several domestic activities, such as smoking, cooking, and cleaning, were found to constitute important sources of indoor air pollution. The indoor pollution caused by PM_2.5 was also found to be more serious in the domestic kitchens than in the living rooms and the results suggest that exposure to PM_2.5 is high and highlights the need for more effective control measures.

Implications: Indoor air pollution is a complex problem that involves many determinant factors. Understanding the relationships and the influence of various indoor and outdoor factors on indoor air quality is very important to prioritize control measures and mitigation action plans. There is currently a lack of research studies in Egypt to investigate determinant factors controlling indoor air quality for urban homes. The present study characterizes the indoor and outdoor concentrations of PM₁₀, PM_2.5, and CO₂ in residential buildings in Alexandria city. The study also determines the indoor and outdoor factors which influence the indoor PM and CO₂ concentrations as well as it evaluates the potential indoor sources in the selected homes. This research will help in the development of future indoor air quality standards for Egypt.     

Characterization of indoor air quality and resident health in an Arizona senior housing apartment building

A survey of key indoor air quality (IAQ) parameters and resident health was carried out in 72 apartments within a single low-income senior housing building in Phoenix, Arizona. Air sampling was carried out simultaneously with a questionnaire on personal habits and general health of residents. Mean PM₁₀ concentrations are 66±16, 58±13, and 24±3 μg/m³ and mean PM_2.5 concentrations are 62±16, 53±13, and 20±2 μg/m³ for the living room, kitchen, and outdoor balcony, respectively. Median PM₁₀ concentrations are 17, 18 and 17 μg/m³ and median PM_2.5 concentrations are 13, 14, and 13 μg/m³, respectively. The initial results indicate that increased indoor particle concentrations coincide with residents who report smoking cigarettes. Indoor formaldehyde concentrations revealed median levels of 36.9, 38.8, and 4.3 ppb in the living room, kitchen, and balcony, respectively. Results show that 36% of living room samples and 44% of kitchen samples exceeded the Health Canada REL for chronic exposure to formaldehyde (40 ppb). Associations between occupants’ behavior, self-reported health conditions, and IAQ are evaluated.

Implications:This study provides a characterization of indoor air quality (IAQ) of subsidized apartments for seniors in Phoenix, Arizona. It is important for policy makers to understand the environments in which low-income seniors live, as they are vulnerable to the health impacts from poor IAQ. Formaldehyde concentrations were found to exceed the Health Canada 8-hr reference exposure level (REL) for up to 44% of indoor samples. Particulate matter exposure was governed by resident behavior (i.e., smoking). Associations between occupants’ behavior, IAQ, and self-reported health conditions are evaluated. This work can provide a foundation for subsequent remediation of IAQ conditions.     

Particulate Air Pollution in Mexico City: A Collaborative Research Project

ABSTRACT

PM₁₀, PM₂₅, precursor gas, and upper-air meteorological measurements were taken in Mexico City, Mexico, from February 23 to March 22, 1997, to understand concentrations and chemical compositions of the city's particulate matter (PM). Average 24-hr PM₁₀ concentrations over the period of study at the core sites in the city were 75 H g/m³. The 24-hr standard of 150 μ g/m³ was exceeded for seven samples taken during the study period; the maximum 24-hr concentration measured was 542 μ g/m³. Nearly half of the PM₁₀ was composed of fugitive dust from roadways, construction, and bare land. About 50% of the PM₁₀ consisted of PM_2.5, with higher percentages during the morning hours. Organic and black carbon constituted up to half of the PM_2.5. PM concentrations were highest during the early morning and after sunset, when the mixed layers were shallow. Meteorological measurements taken during the field campaign show that on most days air was transported out of the Mexico City basin during the afternoon with little day-to-day carryover.     

Prescribed Burns and Wildfires in Colorado: Impacts of Mitigation Measures on Indoor Air Particulate Matter

Abstract

Wildfires and prescribed burns are receiving increasing attention as sources of fine particulate matter (PM_2.5). The goal of this research project was to understand the impact of mitigation strategies for residences impacted by scheduled prescribed burns and wildfires. Pairs of residences were solicited to have PM_2.5 concentrations monitored inside and outside of their houses during four fires. The effect of using air cleaners on indoor PM_2.5 was investigated, as well as the effect of keeping windows closed. Appropriately sized air cleaners were provided to one of each pair of residences; occupants of all of the residences were asked to keep windows shut and minimize opening of exterior doors. Additionally, residents were asked to record all of the activities that may be a source of particulate matter, such as cooking and cleaning. Measurements were made during one prescribed burn and three wildfires during the 2002 fire season. Outdoor 24‐hr average PM_2.5 concentrations ranging from 6 to 38 µg/m³ were measured during the fires, compared with levels of 2–5 µg/m³ during background measurements when no fires were burning. During the fires, PM_2.5 was <3 µg/m³ inside all of the houses with air cleaners installed. This corresponds with a decrease of 63–88% in homes with the air cleaners operating when compared with homes without air cleaners. In the homes without the air cleaners, measured indoor concentrations were 58–100% of the concentrations measured outdoors.     

Personal exposure to PM2.5 and element composition—A comparison between outdoor and indoor workers from two Mexican cities

Many individuals work outdoors in the formal and informal economy of the large urban areas in developing countries, where they are potentially exposed for long periods to high concentrations of ambient airborne particulate matter (PM). This study describes the personal exposures to PM of 2.5 μm aerodynamic diameter and smaller (PM_2.5) for a sample of outdoor and indoor workers in two cities, Mexico City and Puebla, in central Mexico.Thirty-six workers in Mexico City and 17 in Puebla were studied. Thirty were outdoor workers (i.e., taxi and bus drivers, street vendors, and vehicle inspectors) and 23 were indoor (office) workers. Their personal exposures to PM_2.5 were monitored for a mean 19-h period. In Mexico City, the street vendors and taxi drivers overall exposures were significantly higher than indoor workers were. In Puebla, bus drivers had a higher overall exposure than vehicle inspectors or indoor workers. Most of the exposures were above the 65 μg m⁻³ 24-h Mexican standard.In Mexico City, exposures to Si, Ti, Cr, Mn, Fe, Ni, Cu, Mo and Cd were higher for outdoor than for indoor workers. In Puebla, exposures to Si, S, K, Ca, Ti, V, Mn, and Zn also were higher for outdoor workers. In Mexico City outdoor workers exposures to Cu, Pb, Cr, Se and Mo were 4 or more times higher than for Puebla outdoor workers, while Puebla outdoor workers’ exposures to V, Si, Fe and Ca were 3 or more times higher than Mexico City outdoor workers.These results suggest that for these outdoor workers the elevated local ambient air PM concentrations and an extended period spent outside are more important contributors to total exposures than indoor concentrations. These workers could be at particular risk of increased morbidity and mortality associated with ambient PM.     

An assessment of indoor air quality in recent Mexican immigrant housing in Commerce City, Colorado

An indoor air quality assessment was conducted on 100 homes of recent Mexican immigrants in Commerce City, Colorado, an urban industrial community north of Denver. Head of households were administered a family health survey, filled out an activity diary, and participated in a home inspection. Carbon monoxide (CO) and carbon dioxide (CO₂) were measured for 24 h inside the main living area and outside of the homes. Harvard Impactors were used to collect 24-h samples of PM_2.5 at the same locations for gravimetric analysis. Dust samples were collected by vacuuming carpeting and flooring at four locations within the home and analyzed by ELISA for seven allergens. Mean indoor and outdoor PM_2.5 levels were 27.2 and 8.5 μg m⁻³, respectively. Indoor PM_2.5 and CO₂ were elevated in homes for which the number of hours with door/window open was zero compared to homes in which the number of hours was high (>15 h). Indoor PM_2.5 levels did not correlate with outdoor levels and tended to increase with number of inhabitants, and results indicate that the source of indoor particles were occupants and their activities, excluding smoking and cooking. Mean indoor CO₂ and CO levels were 1170 and 2.4 ppm, respectively. Carbon monoxide was higher than the 24-h National Ambient Air Quality Standard in 3 of the homes. The predominant allergens were cat (Fel d 1) and mouse (Mus m 1) allergens, found in 20 and 34 homes, respectively.     

Characterizing and predicting coarse and fine particulates in classrooms located close to an urban roadway

The PM₁₀, PM_2.5, and PM₁ (particulate matter with aerodynamic diameters <10, <2.5, and <1 μm, respectively) concentrations were monitored over a 90-day period in a naturally ventilated school building located at roadside in Chennai City. The 24-hr average PM₁₀, PM_2.5, and PM₁ concentrations at indoor and outdoor environments were found to be 136 ± 60, 36 ± 15, and 20 ± 12 and 76 ± 42, 33 ± 16, and 23 ± 14 μg/m³, respectively. The size distribution of PM in the classroom indicated that coarse mode was dominant during working hours (08:00 a.m. to 04:00 p.m.), whereas fine mode was dominant during nonworking hours (04:00 p.m. to 08:00 a.m.). The increase in coarser particles coincided with occupant activities in the classrooms and finer particles were correlated with outdoor traffic. Analysis of indoor PM₁₀, PM_2.5, and PM₁ concentrations monitored at another school, which is located at urban reserved forest area (background site) indicated 3–4 times lower PM₁₀ concentration than the school located at roadside. Also, the indoor PM₁ and PM_2.5 concentrations were 1.3–1.5 times lower at background site. Further, a mass balance indoor air quality (IAQ) model was modified to predict the indoor PM concentration in the classroom. Results indicated good agreement between the predicted and measured indoor PM_2.5 (R² = 0.72–0.81) and PM₁ (R² = 0.81–0.87) concentrations. But, the measured and predicted PM₁₀ concentrations showed poor correlation (R² = 0.17–0.23), which may be because the IAQ model could not take into account the sudden increase in PM₁₀ concentration (resuspension of large size particles) due to human activities.

Implications:The present study discusses characteristics of the indoor coarse and fine PM concentrations of a naturally ventilated school building located close to an urban roadway and at a background site in Chennai City, India. The study results will be useful to engineers and policymakers to prepare strategies for improving the IAQ inside classrooms. Further, this study may help in the development of IAQ standards and guidelines in India.     

Assessment of personal integrated exposure to fine particulate matter of urban residents in Hong Kong

Metropolitan residents are concerned about their exposure to airborne pollutants. But establishing these exposures is challenging. A compact personal exposure kit (PEK) was developed to evaluate personal integrated exposure (PIE) from time-resolved data to particulate matter with aerodynamic diameter less than 2.5 μm (PM_2.5) in five microenvironments, including office, home, commuting, other indoor activities (other than home and office), and outdoor activities experienced both on weekdays and weekends. The study was conducted in Hong Kong. The PEK measured PM_2.5, reported location and several other factors, stored collected data, as well as reported the data back to the investigators using global system for mobile communication (GSM) telemetry. Generally, PM_2.5 concentrations in office microenvironment were found to be the smallest (13.0 μg/m³), whereas the largest PM_2.5 concentration microenvironments were experienced during outdoor activities (54.4 μg/m³). Participants spent more than 85% of their time indoors, including in offices, homes, and other public indoor venues. On average, 42% and 81% of the time were spent in homes, which contributed 52% and 79% of PIE (during weekdays and weekends, respectively), suggesting that improvement of air quality in homes may reduce overall exposures and indicating the need for actions to mitigate possible public health burdens in Hong Kong. This study also found that various indoor/outdoor microenvironments experienced by urban office workers cannot be accurately represented by general urban air quality data reported from the regulatory monitoring. Such personalized air quality information, especially while in transit or in offices and homes, may provide improved information on population exposures to air pollution.

Implications: A newly developed personal exposure kit (PEK) was used to monitor PM_2.5 exposure of metropolitan citizens in their daily life. Different microenvironments and time durations caused various personal integrated exposure (PIE). The stationary monitoring method for PIE was also compared and evaluated with PEK. Positive protection actions can be taken after understanding the major contribution to PM_2.5 exposure.     

Biomass smoke in Burkina Faso: what is the relationship between particulate matter,carbon monoxide,and kitchen characteristics?

In Burkina Faso where cooking with biomass is very common, little information exists regarding kitchen characteristics and their impact on air pollutant levels. The measurement of air pollutants such as respirable particulate matter (PM₁₀), an important component of biomass smoke that has been linked to adverse health outcomes, can also pose challenges in terms of cost and the type of equipment needed. Carbon monoxide could potentially be a more economical and simpler measure of air pollution. The focus of this study was to first assess the association of kitchen characteristics with measured PM₁₀ and CO levels and second, the relationship of PM₁₀ with CO concentrations, across these different kitchen characteristics in households in Nouna, Burkina Faso. Twenty-four-hour concentrations of PM₁₀ (area) were measured with portable monitors and CO (area and personal) estimated using color dosimeter tubes. Data on kitchen characteristics were collected through surveys. Most households used both wood and charcoal burned in three-stone and charcoal stoves. Mean outdoor kitchen PM₁₀ levels were relatively high (774 μg/m³, 95 % CI 329–1,218 μg/m³), but lower than indoor concentrations (Satterthwaite t value, ?6.14; p?<?0.0001). In multivariable analyses, outdoor kitchens were negatively associated with PM₁₀ (OR?=?0.06, 95 % CI 0.02–0.16, p value <0.0001) and CO (OR?=?0.03, 95 % CI 0.01–0.11, p value <0.0001) concentrations. Strong area PM₁₀ and area CO correlations were found with indoor kitchens (Spearman’s r?=?0.82, p?<?0.0001), indoor stove use (Spearman’s r?=?0.82, p?<?0.0001), and the presence of a smoker in the household (Spearman’s r?=?0.83, p?<?0.0001). Weak correlations between area PM₁₀ and personal CO levels were observed with three-stone (Spearman’s r?=?0.23, p?=?0.008) and improved stoves (Spearman’s r?=?0.34, p?=?0.003). This indicates that the extensive use of biomass fuels and multiple stove types for cooking still produce relatively high levels of exposure, even outdoors, suggesting that both fuel subsidies and stove improvement programs are likely necessary to address this problem. These findings also indicate that area CO color dosimeter tubes could be a useful measure of area PM₁₀ concentrations when levels are influenced by strong emission sources or when used in indoors. The weaker correlation observed between area PM₁₀ and personal CO levels suggests that area exposures are not as useful as proxies for personal exposures, which can vary widely from those recorded by stationary monitors.     

Characteristics and origins of air pollutants in Wuhan,China, based on observations and hybrid receptor models

To identify the characteristics of air pollutants and factors attributing to the formation of haze in Wuhan, this study analyzed the hourly observations of air pollutants (PM_2.5, PM₁₀, NO₂, SO₂, O₃, and CO) from March 1, 2013, to February 28, 2014, and used hybrid receptor models for a case study. The results showed that the annual average concentrations for PM_2.5, PM₁₀, NO₂, SO₂, O₃, and CO during the whole period were 89.6 μg m^?3, 134.9 μg m^?3, 54.9 μg m^?3, 32.4 μg m^?3, 62.3 μg m^?3, and 1.1 mg m^?3, respectively. The monthly variations revealed that the peak values of PM_2.5, PM₁₀, NO₂, SO₂, and CO occurred in December because of increased local emissions and severe weather conditions, while the lowest values occurred in July mainly due to larger precipitation. The maximum O₃ concentrations occurred in warm seasons from May to August, which may be partly due to the high temperature and solar radiation. Diurnal analysis showed that hourly PM_2.5, PM₁₀, NO₂, and CO concentrations had two ascending stages accompanying by the two traffic peaks. However, the O₃ concentration variations were different with the highest concentration in the afternoon. A case study utilizing hybrid receptor models showed the significant impact of regional transport on the haze formation in Wuhan and revealed that the mainly potential polluted sources were located in the north and south of Wuhan, such as Baoding and Handan in Hebei province, and Changsha in Hunan province. Implications: Wuhan city requires a 5% reduction of the annual mean of PM_2.5 concentration by the end of 2017. In order to accomplish this goal, Wuhan has adopted some measures to improve its air quality. This work has determined the main pollution sources that affect the formation of haze in Wuhan by transport. We showed that apart from the local emissions, north and south of Wuhan were the potential sources contributing to the high PM_2.5 concentrations in Wuhan, such as Baoding and Handan in Hebei province, Zhumadian and Jiaozuo in Henan province, and Changsha and Zhuzhou in Hunan province.     

Concentration and characterization of airborne particles in Tehran’s subway system

Particulate matter is an important air pollutant, especially in closed environments like underground subway stations. In this study, a total of 13 elements were determined from PM₁₀ and PM_2.5 samples collected at two subway stations (Imam Khomeini and Sadeghiye) in Tehran’s subway system. Sampling was conducted in April to August 2011 to measure PM concentrations in platform and adjacent outdoor air of the stations. In the Imam Khomeini station, the average concentrations of PM₁₀ and PM_2.5 were 94.4?±?26.3 and 52.3?±?16.5 μg m^?3 in the platform and 81.8?±?22.2 and 35?±?17.6 μg m^?3 in the outdoor air, respectively. In the Sadeghiye station, mean concentrations of PM₁₀ and PM_2.5 were 87.6?±?23 and 41.3?±?20.4 μg m^?3 in the platform and 73.9?±?17.3 and 30?±?15 μg m^?3, in the outdoor air, respectively. The relative contribution of elemental components in each particle fraction were accounted for 43 % (PM₁₀) and 47.7 % (PM_2.5) in platform of Imam Khomeini station and 15.9 % (PM₁₀) and 18.5 % (PM_2.5) in the outdoor air of this station. Also, at the Sadeghiye station, each fraction accounted for 31.6 % (PM₁₀) and 39.8 % (PM_2.5) in platform and was 11.7 % (PM₁₀) and 14.3 % (PM_2.5) in the outdoor. At the Imam Khomeini station, Fe was the predominant element to represent 32.4 and 36 % of the total mass of PM₁₀ and PM_2.5 in the platform and 11.5 and 13.3 % in the outdoor, respectively. At the Sadeghiye station, this element represented 22.7 and 29.8 % of total mass of PM₁₀ and PM_2.5 in the platform and 8.7 and 10.5 % in the outdoor air, respectively. Other major crustal elements were 5.8 % (PM₁₀) and 5.3 % (PM_2.5) in the Imam Khomeini station platform and 2.3 and 2.4 % in the outdoor air, respectively. The proportion of other minor elements was significantly lower, actually less than 7 % in total samples, and V was the minor concentration in total mass of PM₁₀ and PM_2.5 in both platform stations.