Prognosis of environmental concentrations by geo-referenced and generic models: a comparison of GREAT-ER and EUSES exposure simulations for some consumer-product ingredients in the Itter

The aim of this study was the comparison between predicted environmental concentrations (PEC) derived using a generic aspacial model, European Union System for the Evaluation of Substances (EUSES), and a geo-referenced model, the Geo-referenced Regional Environmental Assessment Tool for European Rivers (GREAT-ER). The PECs of some consumer-product ingredients (boron, LAS) and professional uses (EDTA, NTA and Triclosan) were calculated for the river catchment of the Itter, a small tributary to the river Rhine. The PEClocal and PECregional for the water compartment generated by EUSES (default scenario) were subsequently refined with data that realistically reflects the region of North Rhine-Westphalia (NRW scenario) and the Itter catchment (Itter scenario). The results of the three scenarios were then compared with the PECinitial and PECcatchment calculated by GREAT-ER, that was designed as a higher-tiered exposure assessment tool, and with concrete concentrations in the Itter, measured as 24-h composite samples. While the PECregional of all scenarios was close to the lower end of the measured concentrations, the geo-referenced PECs described equally well the real spacial situation. The measured environmental concentrations confirmed the built-in conservatism of the PEClocal calculations by EUSES showing for all investigated chemicals an unrealistically high PEClocal (default). The refinement in the more realistic scenarios could not provide a straight forward general improvement of the PEClocal. In conclusion, when the EUSES prognosis is refined using more detailed substance and regional specific data, it may provide a fairly accurate modelling especially of substances that are not eliminated in the environment. However, in the case of eliminable substances, it does not match the accuracy of higher-tiered geo-referenced exposure models like GREAT-ER.     

沈阳市固定燃烧源挥发性有机化合物2007年排放清单研究

挥发性有机化合物(VOCs)与.OH的反应是对流层臭氧形成的重要化学过程,是导致城市光化学烟雾的根本原因。为建立沈阳市固定燃烧源VOCs排放清单,选取了电力热力行业、钢铁行业和秸秆燃烧3个主要排放源进行研究。结果表明:(1)2007年,沈阳市固定燃烧源VOCs排放总量为8 544.539 t,其中排放量最大的是秸秆燃烧,为6 317.115 t;其次是电力热力行业,为2 225.780 t;最小的是钢铁行业,为1.644 t。(2)沈阳市各区县固定燃烧源VOCs排放量由大到小排序依次为新民市、法库县、东陵区、康平县、辽中县、于洪区、苏家屯区、大东区、沈北新区、铁西区、沈河区、皇姑区、和平区;VOCs排放强度由大到小排序依次为大东区、沈河区、铁西区、东陵区、皇姑区、和平区、于洪区、苏家屯区、法库县、康平县、辽中县、沈北新区、新民市。     

The weaker points of fish acute toxicity tests and how tests on embryos can solve some issues

Fish acute toxicity tests play an important role in environmental risk assessment and hazard classification because they allow for first estimates of the relative toxicity of various chemicals in various species. However, such tests need to be carefully interpreted. Here we shortly summarize the main issues which are linked to the genetics and the condition of the test animals, the standardized test situations, the uncertainty about whether a given test species can be seen as representative to a given fish fauna, the often missing knowledge about possible interaction effects, especially with micropathogens, and statistical problems like small sample sizes and, in some cases, pseudoreplication. We suggest that multi-factorial embryo tests on ecologically relevant species solve many of these issues, and we shortly explain how such tests could be done to avoid the weaker points of fish acute toxicity tests.     

European union system for the evaluation of substances: the second version

This publication presents major changes in the assessment of the risks of chemicals to human health and the environment as implemented in the second version of the European Union System for the Evaluation of Substances, EUSES 2.0. EUSES is a harmonised quantitative risk assessment tool for chemicals. It is the PC-implementation of the technical guidelines developed within the framework of EU chemical legislation for industrial chemicals and biocides. As such, it is designed to support decision making by risk managers in government and industry and to assist scientific institutions in the risk assessment for these substances. The development of EUSES 2.0 is a co-ordinated project of the European Chemicals Bureau, EU Member States and the European chemical industry. Several model concepts, the technical background and the user interface of EUSES have been improved considerably. Major changes in the environmental assessment such as the implementation of emission scenario documents for industrial chemicals and biocides, the addition of the marine risk assessment, the enhancement of the regional model to include global scales, and improvements in the secondary poisoning and environmental effects modelling will be discussed. The update of the human risk assessment module in EUSES focuses on the risk characterisation for both threshold and non-threshold substances with, among others, the introduction of assessment factors. The performance of EUSES is illustrated in an example showing the human and environmental risk assessment of a sanitation disinfectant for private use.     

建筑陶瓷行业SO2污染物评价及总量控制实用方法

采用高斯点源模型对建陶生产造成的SO2地面浓度增量进行计算.利用比例下降模型计算建陶业的SO2允许排放总量,并根据企业的设备生产能力进行了总量分配,在方法上具有较强的可操作性,计算结果表明,可有效降低所在地区的SO2地面浓度.     

Calculation of environmental concentration and comparison of output for existing chemicals using regional multimedia modeling

The environmental fate of 40 existing chemicals is discussed using the EUSES multimedia distribution and risk assessment model with site-specific parameter setting in an urban area of Japan including a highly industrial region. There has been a strong need to assess the environmental fate of a huge number of existing chemicals. Data on the emission amounts of chemicals are essential for such prediction, and PRTR surveys may yield this data. The study delivered the following results: (1) Volatile compounds with large amounts of emission showed higher predicted concentrations in air, and the concentrations of several compounds agreed well with averaged monitoring data within an order of magnitude. (2) A close relationship was found between the concentration of water and that of sediment, suggesting that the fate of chemicals in sediment essentially depended on the water environment. (3) A group of volatile solvents had high mass distribution ratio to air. Some compounds having high solubility in water were also included in that group due to the high ratio of air emission. Highly hydrophobic compounds with logK(OW) larger than 6.0 showed a high distribution ratio to soil and sediment. (4) Volatile compounds were mostly taken through air. The exposure through fish is a dominant pathway for highly hydrophobic compounds. (5) Exposure ratio could be gathered from physicochemical properties. The exposure from fish intake was roughly estimated by logK(OW), whereas exposure from air and water intake was difficult to estimate simply by vapor pressure and solubility in water, respectively.     

Environmental impact assessment (EIA): Equilibrium fugacity calculations and worst case approach

A mathematical model UNITRISK which can be used for screening purposes and risk ranking was set up to calculate relative risk values of single chemicals and mixtures of chemicals towards single or mixtures of organisms via contamination of air, water, soil and food dose. The concentration values are calculated by applying the fugacity concept or a dose must be defined. The dose-response is assumed to be linear versus concentration and degradative processes are not considered which is the worst case. The assumption that equilibria between the environmental phases exist is simplifying the model and is also representing the worst case. A mean risk factor is calculated which is 1 if the endpoint values (LC₅₀, LD₅₀, ADI, etc.) are exceeded for the investigated organisms and man.     

Steps towards environmental hazard assessment of new chemicals (including a hazard ranking scheme,based upon directive 79/831/EEC)

Directive 79/831/EEC came into force on 18th September 1981, enabling all the Member States of the EEC to classify so-called “new chemicals” with respect to their potential hazard to the environment and to human health on a standardized basis (Directive 79/831/EEC, Annex VII). The authors are of the opinion that the assessment of the “environmental hazard” of new chemicals before they are placed on the market, represents, in the present critical economic /ecological situation, which practically all the Member States have in common, a particular challenge to the scientific community and the competent authorities. The comments aim to achieve the following - to provide a more precise definition of certain key terms and to point out a way of selecting from the bundle of new chemicals those (few) which are potentially hazardous; a way which is clear to the administration, the scientific community, industry and, not least of all, to the individual as taxpayer and consumer.     

Comparison of two screening level risk assessment approaches for six disinfectants and pharmaceuticals

For three examples of both groups (the disinfectants biphenylol, 4-chloro-m-cresol and triclosan and the pharmaceuticals ivermectin, ibuprofen and oxytetracycline) a relative initial risk assessment (RIRA) was performed assuming a standard emission of 1 kg/d to the most relevant environmental compartment. In addition the hazard of the compounds was evaluated based upon their persistence, toxicity and bioaccumulative properties (PTB). Both estimated and measured parameters were used for this purpose. In addition to an analysis of the risks of the pharmaceuticals and disinfectants per se, the capacity to discern between the intrinsic risk of different compounds is evaluated for both criteria used. It is concluded that the RIRA has a higher discriminative value and yields more information compared to the PTB-criterion.     

The spatial scale of organic chemicals in multimedia fate modeling. Recent developments and significance for chemical assessment

In the last years, the spatial range (SR) or characteristic travel distance (CTD) of organic chemicals has found increasing scientific interest as an indicator of the long-range transport (LRT) potential and, in combination with persistence, as a kind of 'hazard' indicator on the exposure level. This development coincides with European debates about more effective and more preventive approaches to the chemicals assessment, and about an international, legally-binding instrument for the phase out of persistent organic pollutants (POPs). Persistence and LRT potential are important issues in these debates. Here, the development of the concept of assessing the spatial scale from early ideas in the 1970s and 1980s to recent studies in the field of multimedia fate and transport modeling is summarized. Different approaches to the modeling of environmental transport (advective and dispersive) and different methods for quantifying the SR or CTD are compared. Relationships between SR or CTD and different persistence measures are analyzed. Comparison of these relationships shows that conclusions for chemical assessment should be based on an evaluation of different persistence and spatial scale measures. The use of SR or CTD and persistence as hazard indicators in the chemicals assessment is illustrated.     

Monitoring, modelling and environmental exposure assessment of industrial chemicals in the aquatic environment

Monitoring and laboratory data play integral roles alongside fate and exposure models in comprehensive risk assessments. The principle in the European Union Technical Guidance Documents for risk assessment is that measured data may take precedence over model results but only after they are judged to be of adequate reliability and to be representative of the particular environmental compartments to which they are applied. In practice, laboratory and field data are used to provide parameters for the models, while monitoring data are used to validate the models' predictions. Thus, comprehensive risk assessments require the integration of laboratory and monitoring data with the model predictions. However, this interplay is often overlooked. Discrepancies between the results of models and monitoring should be investigated in terms of the representativeness of both. Certainly, in the context of the EU risk assessment of existing chemicals, the specific requirements for monitoring data have not been adequately addressed. The resources required for environmental monitoring, both in terms of manpower and equipment, can be very significant. The design of monitoring programmes to optimise the use of resources and the use of models as a cost-effective alternative are increasing in importance. Generic considerations and criteria for the design of new monitoring programmes to generate representative quality data for the aquatic compartment are outlined and the criteria for the use of existing data are discussed. In particular, there is a need to improve the accessibility to data sets, to standardise the data sets, to promote communication and harmonisation of programmes and to incorporate the flexibility to change monitoring protocols to amend the chemicals under investigation in line with changing needs and priorities.     

The measurement of roadway PM10 emission rates using atmospheric tracer ratio techniques

In this work, stationary and mobile point source tracer release techniques have been used to determine PM₁₀ emission rates from four-lane commercial/residential paved roads under sanded and unsanded conditions, and from unpaved roads relative to site-specific vehicular and ambient parameters. Measured street (4 + lanes; ? 10,000 vehicles per day) emission factors for unsanded and sanded roads were 40 and 20% lower, respectively, than the EPA approved reference value. The sanded road emission factor was approximately 40% higher than that for the unsanded road. These results indicate a consistent relationship between PM₁₀ and relative humidity under unsanded conditions. There is some evidence to suggest that street sweeping has a measurable effect on PM,, emission reduction during periods of low relative humidity (i.e. ? 30%). Within the constraints imposed by the variable experimental conditions, the emission factors determined for unpaved roads agreed reasonably well with the unpaved road empirical formula. Limited correlations were observed with ambient meteorological parameters. The capability of the “upwind-dowiawind” concentration modeling method to predict accurate emission was tested using a Gaussian dispersion model (SIMFLUX). Predictions agreed well with the experimentally determined emission factors.     

Sensitivity of schemes for ecotoxicological hazard ranking of chemicals

Data from an environmental hazard profile, including different tests on accumulation and degradation as well as Daphnia acute toxicity were used for a classification of chemicals into three categories: High hazard potential, uncertain hazard potential, and low likelyhood of environmental hazard. Giving the used evaluation factors different weights, leads to a modification in classification.     

Evaluation of approaches for terrestrial hazard classification

Hazard assessment is an essential element in the evaluation of the potential effects of chemical substances on the environment. To date, most work has focused on hazard assessment schemes for the aquatic environment, but in recent years, a number of proposals have been developed for other environmental compartments. Due to limited datasets, the suitability of the toxicity cut-off values in these schemes has not been fully determined and the practicalities associated with using these approaches have not been fully established. This study, which focused on the soil compartment, was performed to examine cut-off values proposed by two terrestrial hazard assessment schemes and establish the availability of data. Data on earthworms indicated that current proposals for toxicity cut-off values are appropriate. However, analysis of IUCLID (International Uniform ChemicaL Information Database) indicates that even for commonly used high production volume chemicals, insufficient data are available to enable classification. Whilst the necessary data may already be available for selected groups of substances (e.g. pesticides and veterinary medicines), a significant experimental testing programme would therefore be required before a terrestrial classification system could be applied widely. Such data may become available in the future as a result of initiatives such as REACH.     

The effect of export to the deep sea on the long-range transport potential of persistent organic pollutants

BACKGROUND: Export to the deep sea has been found to be a relevant pathway for highly hydrophobic chemicals. The objective of this study is to investigate the influence of this process on the potential for long-range transport (LRT) of such chemicals. METHODS: The spatial range as a measure of potential for LRT is calculated for seven PCB congeners with the multimedia fate and transport model ChemRange. Spatial ranges for cases with and without deep sea export are compared. RESULTS AND DISCUSSION: Export to the deep sea leads to increased transfer from the air to the surface ocean and, thereby, to lower spatial ranges for PCB congeners whose net deposition rate constant is similar to or greater than the atmospheric degradation rate constant. This is fulfilled for the PCB congeners 101, 153, 180, and 194. The spatial ranges of the congeners 8, 28, and 52, in contrast, are not affected by deep sea export. With export to the deep sea included in the model, the spatial ranges of the heavier congener are similar to those of the lighter ones, while the intermediate congeners 101 and 153 have the highest potential for long-range transport. CONCLUSIONS: Transfer to the deep ocean affects the mass balance and the potential for LRT of highly hydrophobic chemicals and should be included in multimedia fate models containing a compartment for ocean water.     

Ozonation of a mixture of estrogens and progestins in aqueous solution: Interpretation of experimental results by computational methods

In this paper the results of a thorough evaluation of the environmental fate and effects of azilsartan are presented. Azilsartan medoxomil is administered as a pro-drug for the treatment of patients with essential hypertension. The pro-drug is converted by hydrolysis to the active pharmaceutical ingredient azilsartan. Laboratory tests to evaluate the environmental fate and effects of azilsartan medoxomil were conducted with azilsartan and performed in accordance with OECD test guidelines. The predicted environmental concentration (PEC) in surface water was estimated at 0.32 μg L⁻¹ (above the action limit of 0.01 μg L⁻¹), triggering a Phase II assessment. Azilsartan is not readily biodegradable. Results of the water sediment study demonstrated significant shifting of azilsartan metabolites to sediment. Based on the equilibrium partitioning method, metabolites are unlikely to pose a risk to sediment-dwelling organisms. Ratios of the predicted environmental concentrations (PECs) to the predicted-no-effect concentrations (PNECs) did not exceed the relevant triggers, and the risk to aquatic, sewage treatment plant (STP), groundwater and sediment compartments was concluded acceptable. A terrestrial assessment was not triggered. Azilsartan poses an acceptable risk to the environment.     

Life Cycle Assessment as Part of Sustainability Assessment for Chemicals (5 pp)

Background LCA is the only internationally standardized environmental assessment tool (ISO 14040-43) for product systems, including services and processes. The analysis is done ‘from cradle-to-grave’, i.e. over the whole life cycle. LCA is essentially a comparative method: different systems fulfilling the same function (serving the same purpose) are compared on the basis of a ‘functional unit’ - a quantitative measure of this function or purpose. It is often believed that LCA can be used for judging the (relative) sustainability of product systems. This is only partly true, however, since LCA is restricted to the environmental part of the triad ‘environment/ecology - economy - social aspects (including intergenerational fairness)’ which constitutes sustainability. Standardized assessment tools for the second and the third part are still lacking, but Life Cycle Costing (LCC) seems to be a promising candidate for the economic part. Social Life Cycle Assessment still has to be developed on the basis of known social indicators.Method and Limitations LCA is most frequently used for the comparative assessment or optimization analysis of final products. Materials and chemicals are difficult to analyse from cradle-to-grave, since they are used in many, often innumerable product systems, which all would have to be studied in detail to give a complete LCA of a particular material or substance! This complete analysis of a material or chemical is evidently only possible in such cases where one main application exists. But even if one main application does exist, e.g. in the case of surfactants (chemicals) and detergents (final products), the latter may exist in a great abundance of compositions. Therefore, chemicals and materials are better analysed ‘from cradle-to-factory gate’, leaving the analysis of the final product(s), the use phase and the ‘end-of-life’ phases to specific, full LCAs.Conclusion A comparative assessment of production processes is possible, if the chemicals (the same is true for materials) produced by different methods have exactly the same properties. In this case, the downstream phases may be considered as a ‘black box’ and left out of the assessment. Such truncated LCAs can be used for environmental comparisons, but less so for the (environmental) optimization analysis of a specific chemical: the phases considered as ‘black box’ and left out may actually be the dominant ones. A sustainability assessment should be performed at the product level and contain the results of LCC and social assessments. Equal and consistent system boundaries will have to be used for these life cycle tools which only together can fulfil the aim of assessing the sustainability of product systems.     

Relative sensitivity of one freshwater and two marine acute toxicity tests as determined by testing 30 offshore E & P chemicals

Acute toxicity of 30 offshore E & P (Exploration and Production) chemicals was measured using the three standard test organisms Daphnia magna (freshwater cladoceran), Acartia tonsa (marine copepod) and Skeletonema costatum (marine diatom alga). Test chemicals included 20 water-soluble and 10 (partially) non-soluble products. For 22 out of the 30 chemicals, the difference in sensitivity between the three tests varied within one order of magnitude. A very good correlation was found between the two marine tests (r = 0.96, P < 0.01, n = 30), and a correlation coefficient of r = 0.78 (P < 0.01, n = 30) was found between D. magna and both A. tonsa and S. costatum, individually. When the comparison of D. magna and A. tonsa sensitivity was based only on the water-soluble chemicals, a significantly higher correlation was obtained (r = 0.84, n = 20), indicating that the sample preparation method used for the (partially) non-soluble chemicals (the water accommodated fraction (WAF) method) induces additional variation between tests performed with different test media. (Partially) non-soluble chemicals are characterised by phase separation or precipitation at the concentrations used for testing. In a WAF-based test, each test concentration/exposure level is prepared separately, and following mixing and separation, only the water phase is used for testing. Toxicity is related to the amount of substance originally added to the mixing vessels. For 25 of the 30 chemicals, D. magna was found to be less sensitive than the marine copepod by a factor >2. The generally higher sensitivity of the marine toxicity tests compared to the Daphnia test emphasise the importance of using marine data for environmental hazard classification as well as for environmental risk assessment purposes.     

In silico prediction of Tetrahymena pyriformis toxicity for diverse industrial chemicals with substructure pattern recognition and machine learning methods

There is an increasing need for the rapid safety assessment of chemicals by both industries and regulatory agencies throughout the world. In silico techniques are practical alternatives in the environmental hazard assessment. It is especially true to address the persistence, bioaccumulative and toxicity potentials of organic chemicals. Tetrahymena pyriformis toxicity is often used as a toxic endpoint. In this study, 1571 diverse unique chemicals were collected from the literature and composed of the largest diverse data set for T. pyriformis toxicity. Classification predictive models of T. pyriformis toxicity were developed by substructure pattern recognition and different machine learning methods, including support vector machine (SVM), C4.5 decision tree, k-nearest neighbors and random forest. The results of a 5-fold cross-validation showed that the SVM method performed better than other algorithms. The overall predictive accuracies of the SVM classification model with radial basis functions kernel was 92.2% for the 5-fold cross-validation and 92.6% for the external validation set, respectively. Furthermore, several representative substructure patterns for characterizing T. pyriformis toxicity were also identified via the information gain analysis methods.