一般性问题

X701200502160Pd/Ce0.5Zr0.5O2三效催化剂负载方法/朱保伟…(中科院生态环境研究中心)∥环境科学/中科院生态环境研究中心.-2004,25(6).-21~25环图X-5分别采用沉积沉淀、直接混合和传统的浸渍法制备1%Pd/Ce0.5Zr0.5O2催化剂,研究了Pd负载方法对催化剂活性影响。运用H2-TPR和原位漫反射红外(DRIFTS)研究了Pd-铈锆载体间的相互作用及Pd/Ce0.5Zr0.5O2催化剂上的三效反应机理。结果表明沉积沉淀法制备的Pd/Ce0.5Zr0.5O2催化剂(Pd-DP)表现出最强的Pd-载体作用及最优活性,原位红外实验发现Pd-DP上存在与传统的浸渍法制备的Pd-IMP…     

Pd/CZ/Al2O3催化剂的制备、表征与三效催化性能

以共浸渍法制得的氧化铝负载铈锆固溶体为载体,并浸渍贵金属Pd得到了Pd/CZ/Al₂O₃催化剂.实验结果表明,该催化剂在老化前后都表现出良好的三效催化活性,新鲜样品Pd/CZ/Al₂O₃活性与Pd/CZ相当,老化后样品前者优于后者.结合XRD,BET,TPR等表征手段,讨论了Pd/CZ/Al₂O₃的催化活性特别是高温老化后活性与其组成结构之间的内在关系,揭示了其老化后仍具有较高活性的主要原因在于保持了Pd与CZ/Al₂O₃复合载体之间的强相互作用(SMSI).     

CuxCe1-xO2/γ-Al2O3催化剂催化燃烧甲苯性能的研究

以γ-Al₂O₃ 为载体,以复合氧化物Cu_xCe_1-xO₂为活性组分,其中,x=0.1,0.2,0.4,0.6,0.8,通过浸渍法制备了一系列Cu_xCe_1-xO₂/γ-Al₂O₃催化剂.在固定床反应器中评价了催化剂对甲苯的催化活性,通过XRD、SEM对催化剂进行表征,并运用ICP-MS分析并计算Cu、Ce的摩尔比以及活性组分的负载量.结果表明,在Cu_xCe_1-xO₂/γ-Al₂O₃催化剂中Cu、Ce摩尔比的实际值与理论值相近,活性组分的负载量在19%以上,而且对甲苯都有较好的低温催化活性,其中当x=0.2时,即Cu_0.2Ce_0.8O₂/γ-Al₂O₃催化剂对甲苯的催化活性最高,其中T₁₀=160 ℃,T₉₀=265 ℃;当甲苯的进口浓度在700~3000 mg·m^-3时,进口浓度对Cu_0.2Ce_0.8O₂/γ-Al₂O₃催化剂的催化活性影响较小,且经过连续80 h的稳定性操作后转化率仍然保持在90%以上.     

Ce/Zr系列催化剂上碳颗粒物燃烧行为

分别在TG和TPO上考察了CeO₂,ZrO₂及不同Ce/Zr比的CexZr1-xO₂固溶体催化剂上soot的燃烧性能,同时考察了反应气氛对活性的影响.结果表明:Ce基催化剂能明显降低soot的起燃温度,Ce/Zr比的不同导致Ce_xZr_1-xO₂催化剂性能的差异.反应的速度控制步骤随O₂浓度的不同而改变;H₂O对Ce_0.5Zr_0.5O₂上soot的氧化活性基本没有影响;由于NO氧化产生的NO₂具有更强的的氧化能力,因此NO对soot的燃烧具有促进作用,起燃温度降低了30℃.催化剂上的β氧种参与了soot燃烧过程.     

碳包覆Pd/Al2O3催化剂催化4-溴苯酚加氢脱溴的活性和稳定性调控研究

在污染物液相催化加氢脱卤过程中，提高催化剂的稳定性至关重要.以水热合成法制备了不同碳包覆量的Pd/Al₂O₃@C催化剂，对催化剂进行了系列表征，并将催化剂应用于4-溴苯酚（4-BP）污染物的催化加氢脱溴反应.表征结果显示碳层提高了Pd/Al₂O₃的表面疏水性，有利于4-BP在催化剂上的吸附.并且在Pd/Al₂O₃@C催化剂的碳化过程中，碳还原部分Pd颗粒，并保留部分正价态Pd活性位，增强了4-BP中C-Br键的活化.与Pd/Al₂O₃相比，碳涂层提高了催化剂的催化活性.但当碳包覆量超过最佳包覆量后，暴露的Pd粒子随碳包覆量的增加而减少，导致活性下降.此外，碳层修饰后，催化剂的稳定性显著提高，从而大大抑制了Pd粒子的团聚和损耗.Pd/Al₂O₃@C表面的碳涂层对卤素具有较高的耐受性，从而减轻了液相催化加氢脱卤反应中活性中心的中毒.     

富氧条件下SnO2/Al2O3催化剂上丙烯选择性还原NOx的研究

考察了分别用浸渍法、共沉淀法和溶胶-凝胶法制备的SnO₂/Al₂O₃催化剂上丙烯选择性还原NO_x的催化活性,发现制备方法与Sn的负载量对其活性有重要影响.溶胶-凝胶法制备的SnO₂/Al₂O₃催化剂活性最高,Sn的最佳负载量为5%.与浸渍法和共沉淀法制备的5%SnO₂/Al₂O₃催化剂相比,溶胶-凝胶法制备的5%SnO₂/Al₂O₃催化剂受水蒸汽的抑制作用较弱,并且在水和SO₂共存的条件下活性最高.此外,反应气中丙烯及氧气浓度的增加有利于NO_x转化率的提高.     

Al2O3为载体的催化剂净化贫燃汽车尾气研究

在富氧条件下,考察了C₃H₆和C₂H₅OH在Ag/Al₂O₃、In/Al₂O₃、Sn/Al₂O₃、Co/Al₂O₃、Pt/Al₂O₃和Ag/Al₂O₃+Pt/Al₂O₃组合催化剂上选择性还原NO的性能.结果表明,Ag/Al₂O₃具有最高的NO还原活性.在负载型过渡金属氧化物催化剂上,会生成显著量的CO,其HC和CO氧化转化温度也远远高于Pt/Al₂O₃催化剂.串联组合Ag/Al₂O₃+Pt/Al₂O₃催化剂可显著拓宽活性温度范围,促进HC和CO氧化,降低N₂O和CH₃CHO生成量.     

SO2对Ag/Al2O3催化剂上CH3OH还原NO性能的影响

用溶胶-凝胶混合法制备了Ag负载量为5%的Ag/A1₂O₃催化剂.研究了富氧条件下,SO₂对CH₃OH在催化剂上还原NO性能的影响.结果表明,反应气不含SO₂和H₂O时,NO还原活性温度较低,有显著量N₂O生成,这被归因为反应过程中,部分氧化态Ag被还原为金属Ag.添加SO₂或同时添加SO₂和H_{2相似文献}   

富氧条件下在Ag/Al2O3催化剂上C3H6选择性还原NO

比较富氧条件下,Ｃ₃Ｈ₆ 在溶胶－凝胶和浸渍２种方法制备的Ａｇ／Ａｌ₂Ｏ₃ 催化剂上还原ＮＯ的活性和热稳定性． 结果表明,从活性角度考虑,采用溶胶－凝胶法制备Ａｇ／Ａｌ₂Ｏ₃ 催化剂时,最佳Ａｇ 负载量（ｗｔ）为４％ ～６％ ,其最大活性与浸渍法制备的２％ Ａｇ／Ａｌ₂Ｏ₃ 催化剂相同,而溶胶－凝胶法制备的催化剂有更宽的活性温度范围． 随着焙烧温度提高,溶胶－凝胶法制备的Ａｇ／Ａｌ₂Ｏ₃ 催化剂的比表面和活性下降比浸渍法慢．此外,还考察了气氛中含有ＣＯ对Ａｇ／Ａｌ₂Ｏ₃ 催化剂活性的影响,结果表明活性降低,其原因可能是活性高的氧化态Ａｇ 被ＣＯ部分还原为活性低的还原态Ａｇ．     

Reduction of NO by CO using Pd-CeTb and Pd-CeZr catalysts supported on SiO2 and La2O3-Al2O3

The catalytic activity of Pd catalysts supported on Ce_0.73Tb_0.27O_x/SiO₂, Ce_0.6Zr_0.4O_x/SiO₂, Ce_0.73Tb_0.27O_x/La₂O₃-Al₂O₃ and Ce_0.6Zr_0.4O_x/La₂O₃-Al₂O₃ was studied using the reduction of NO by CO. The catalysts were characterized by X-ray fluorescence, surface area, X-ray diffraction, temperature-programmed reduction, CO chemisorption and oxygen storage capacity. Temperature-programmed reduction results indicated that Tb or Zr incorporation improves the reducibility and oxygen storage capacity. CO chemisorption data suggested the presence of large PdO particles due to the low CO/Pd ratio. No significant differences were obtained in light off temperatures (T_{Light off}) for all Pd catalysts and the most active was 1.5%Pd/Ce_0.6Zr_0.4O_x/SiO₂.     

Pd/TiO2对水体中2,4-二氯酚的催化加氢脱氯研究

分别采用沉淀-沉积法和浸渍法合成了Pd/TiO2催化剂,采用透射电镜(TEM)、X射线衍射(XRD)和电感耦合等离子体发射光谱(ICP-AES)对材料进行了表征,并对2,4-二氯酚的催化加氢脱氯反应进行了研究.结果表明,2种方法制备的催化剂在加氢脱氯反应中均具有较好的效果,沉淀-沉积法制备的催化剂活性更高,当反应物初始浓度为3.11 mmol.L-1,pH为12,催化剂用量为50 mg时,45 min内2,4-二氯酚可以完成脱氯过程.酸性条件有利于反应的进行.当催化剂用量在15～80 mg时,反应初活性没有明显变化,因此催化反应过程不受传质阻力的影响.当反应物初始浓度在0.62～3.11 mmol.L-1时反应初活性随浓度的提高显著增加,但进一步增加反应物的浓度时初活性没有明显提高,因此2,4-二氯酚在催化剂上的加氢脱氯行为符合Langmuir-Hinshelwood模型,表明2,4-二氯酚的加氢脱氯受表面吸附所控制.     

Effect of MoO3 on vanadium based catalysts for the selective catalytic reduction of NOx with NH3 at low temperature

The selective catalytic reduction(SCR) activities of the MoO_3 doped V/WTi catalysts prepared by the incipient wetness impregnation method at low temperature were investigated.The results showed that the addition of MoO_3 could enhance the NO_ xconversion at low temperature and the best SCR activity was obtained when the dosage of MoO_3 reached5 wt.%. The NH3-TPD and DRIFTS experiments indicated that the addition of MoO_3 changed the type and number of acid sites on the surface of catalysts and reaction activities of acid sites were altered at the same time. The redox capacity and amount of active oxygen species got improved for V3Mo5/WTi catalyst, which could be confirmed by the H_2-TPR and transient response experiments. Water vapor inhibited the NO_xconversion at low temperature. Deposition of ammonium sulfate or bisulfate might be main reason for the loss of catalytic activity in the presence of SO_2 at low temperature. Choosing the suitable NH_3/NO ratio and elevation of reaction temperature both could weaken the influence of SO_2 on the SCR activity of the V3Mo5/WTi catalyst. Thermal treatment of the deactivated catalyst at350°C could get the low temperature activity recovered. The decrease of GHSV improved the de NO_x efficiency at low temperature and we speculated that the rational technological process and operation parameters could contribute to the application of this kind of catalysts in real industrial environment.     

Effect of Ce doping of TiO2 support on NH3-SCR activity over V2O5-WO3/CeO2-TiO2 catalyst

CeO2–TiO2composite supports with different Ce/Ti molar ratios were prepared by a homogeneous precipitation method, and V2O5–WO3/CeO2–TiO2catalysts for the selective catalytic reduction（SCR） of NOx with NH3 were prepared by an incipient-wetness impregnation method. These catalysts were characterized by means of BET, XRD, UV–Vis,Raman and XPS techniques. The results showed that the catalytic activity of V2O5–WO3/TiO2 was greatly enhanced by Ce doping（molar ratio of Ce/Ti = 1/10） in the TiO2 support.The catalysts that were predominantly anatase TiO2 showed better catalytic performance than the catalysts that were predominantly fluorite CeO2. The Ce additive could enhance the surface adsorbed oxygen and accelerate the SCR reaction. The effects of O2 concentration, ratio of NH3/NO, space velocity and SO2 on the catalytic activity were also investigated. The presence of oxygen played an important role in NO reduction. The optimal ratio of NH3/NO was 1/1 and the catalyst had good resistance to SO2 poisoning.     

纳米Fe3O4/CeO2-H2O2非均相类Fenton体系对3,4-二氯三氟甲苯的降解

以浸渍法制备的新型纳米Fe3O4/Ce O2为催化剂,3,4-二氯三氟甲苯(3,4-DCBTE)为目标污染物,在Fe3O4/Ce O2-H2O2非均相类Fenton体系中对目标污染物的降解进行研究,考察催化剂的催化效果和温度、p H、H2O2投加量等因素对催化剂催化效果的影响.结果表明,以纳米Fe3O4/Ce O2作为催化剂的非均相类Fenton体系对3,4-二氯三氟甲苯的处理效果极佳;随着温度的升高,纳米Fe3O4/Ce O2的催化效果不断提高;在偏酸性环境中,p H越低催化效果越好,p H=2时反应去除效率可达96.67%;随着H2O2投加量的增加,3,4-二氯三氟甲苯的降解效率先提高后降低,投加量为15 mg·L-1时去除效果最好可达99.47%;随着催化剂投加量的增加,同样出现了处理效果先升高后降低的现象,投加量为0.5 g·L-1时催化效果最好可达99.64%.在以纳米Fe3O4/Ce O2为催化剂的非均相类Fenton体系中,3,4-二氯三氟甲苯的降解符合一级反应动力学,反应所需活化能较低只需30.26 k J·mol-1.     

不同方法制备Co3O4催化剂CO-SCR性能及机制

氮氧化物(NOx)是造成细颗粒物、近地面臭氧等大气污染问题的重要前体物.随着大气污染治理行动的深入,对工业锅炉/窑炉烟气排放的NOx进行控制十分重要.采用不同方法制备了一系列Co_3O_4催化剂,考察了不同制备方法对CO选择性催化还原NO(CO-SCR)反应活性的影响,通过BET、XRD、Raman、HR-TEM和SEM等技术对该系列催化剂进行了表征.活性测试表明,以硫酸钴为前驱体用固态研磨法制备的Co_3O_4-S催化剂具有更优异的CO-SCR反应活性,且表现出较好的抗水蒸气性能,以醋酸钴为前驱体用固态研磨法制备的Co_3O_4-C催化剂显示出较好的抗水性能. NO氧化结果显示,催化剂的NO氧化效果越好,CO-SCR活性也越好. Raman表征结果显示,Co_3O_4-S表面可能含有更多的Co2+离子,从而有利于形成氧空位. H2-TPR结果表明,Co_3O_4-S催化剂的氧化还原性较好. HR-TEM表征发现Co_3O_4-S和Co_3O_4-O主要暴露(111)和(220)晶面,而更多(220)晶面的暴露可能更有利于反应的进行.     

非热等离子体结合CuO催化剂或Ca(OH)2吸收剂去除氮氧化物

采用非热等离子体结合催化或现场化学吸收的2种方法来去除气流中的NO_x.结果表明,非热等离子体结合催化,反应器内的CuO催化剂能有效地促进NO的还原反应;相对于催化还原NO而言,脉冲电晕作用下能有效地降低NO催化还原的反应温度.当催化剂为CuO,脉冲电压为18kV,反应温度为200℃,还原剂为1%CO及NO进口浓度为719 mg/m³条件下,NO的去除率达到了100%.非热等离子体结合现场化学吸收方法,是一种在常温下从气流中净化氮氧化物的有效方法,NO的去除率远远高于反应器内没有吸收剂的情况.可以认为反应器内的Ca(OH)₂吸收剂通过与NO的氧化产物NO₂或NO₃的吸收反应促进了NO的去除.当反应器内有Ca(OH)₂吸收剂存在时,在脉冲电压为18kV,O₂浓度为2%及NO进口浓度为1 050 mg/m³条件下,NO的去除率达到了100%.     

Ultrasound-assistant preparation of Cu-SAPO-34 nanocatalyst for selective catalytic reduction of NO by NH3

The influence of the various preparation methods of Cu-SAPO-34 nanocatalysts on the selective catalytic reduction of NO with NH₃ under excess oxygen was studied. Cu-SAPO-34 nanocatalysts were prepared by using four techniques: conventional impregnation (IM), ultrasound-enhanced impregnation (UIM), conventional deposition precipitation (DP) using NaOH and homogeneous deposition precipitation (HDP) using urea. These catalysts were characterized in detail by various techniques such as N₂-sorption, XRD, TEM, H₂-TPR, NH₃-TPD and XPS to understand the catalyst structure, the nature and the dispersed state of the copper species, and the acid sites for NH₃ adsorption. All of the nanocatalysts showed high activities for NO removal. However, the activities were different and followed the sequence of Cu-SAPO-34 (UIM) > Cu-SAPO-34 (HDP) > Cu-SAPO-34 (IM) > Cu-SAPO-34 (DP). Based on the obtained results, it was concluded that the NO conversion on Cu-SAPO-34 nanocatalysts was mainly related to the high reducibility of the isolated Cu^2 + ions and CuO species, the number of the acid sites and the dispersion of CuO species on SAPO-34.