Comparison of pressurized fluid extraction, Soxhlet extraction and sonication for the determination of polycyclic aromatic hydrocarbons in urban air and diesel exhaust particulate matter

In order to characterize and compare the chemical composition of diesel particulate matter and ambient air samples collected on filters, different extraction procedures were tested and their extraction efficiencies and recoveries determined. This study is an evaluation of extraction methods using the standard 16 EPA PAHs with HPLC fluorescence analysis. Including LC analysis also GC and MS methods for the determination of PAHs can be used. Soxhlet extraction was compared with ultrasonic agitation and pressurized fluid extraction (PFE) using three solvents to extract PAHs from diesel exhaust and urban air particulates. The selected PAH compounds of soluble organic fractions were analyzed by HPLC with a multiple wavelength shift fluorescence detector. The EPA standard mixture of 16 PAH compounds was used as a standard to identify and quantify diesel exhaust-derived PAHs. The most effective extraction method of those tested was pressurized fluid extraction using dichloromethane as a solvent.     

PAH and PCB in soils of Switzerland--status and critical review

The surface soil concentrations (0-20 cm) of the Swiss soil monitoring network (NABO) with 105 observation sites representing all major land use types ranged for the sum of 16 EPA PAH (PAH(16)) from 32 to 8465 microg kg(-1) (median 163 microg kg(-1)), for benzo[a]pyrene (BaP) from 0.5 to 1129 microg kg(-1) (median 13 microg kg(-1)) and for the sum of seven IRMM PCB (PCB(7)) from 0.5 to 12 microg kg(-1) (median 1.6 microg kg(-1)). The legal guide values of Switzerland were exceeded for PAH(16) at only three and for BaP at two sites. The PCB(7) concentrations were clearly below any assessment value. The concentration ranges were overlapping between all land use types. Tendencies for higher concentrations were observed at urban and viticulture sites. The overall measurement precision at repeatability conditions ranged from 1 to 37% RSD for PAH(16), BaP and PCB(7). The median bias for the chemical analysis was around zero for PAH(16), +5% for BaP and -5% for PCB(7) with spreads ranging from less than -20% up to more than +30%. The PAH profiles were clearly dominated by phenanthrene. Stratification by land use revealed a prevalence of benzo[a]pyrene at urban and naphthalene at conservation sites. For PCB, the general congener rank order was PCB no. 153 > 138 > 101 > 180. From a broad correlation screening only PAH(16)/BaP (r = 0.88**) were relevant for practical soil protection. The extensive comparison with other studies was severely biased by the lack of harmonisation, especially concerning sampling depth, sampling support, analytical method and the sum calculation procedure.     

Validation of a European standard for the determination of hexavalent chromium in solid material

A European standard for the determination of Cr(vi) in solid material has been elaborated in the framework of an international co-operation and finally validated in the course of an interlaboratory comparison. The procedure is based on the alkaline digestion prescribed by EPA method 3060A followed by ion chromatography and determines an operationally defined content of Cr(vi), including water-soluble and insoluble chromates. A preliminary robustness study was carried out in order to compare different extraction methodologies and to study the equivalency of different analytical methods for the determination of Cr(vi) in alkaline extracts of soil and waste materials. During an interlaboratory validation trial with 19 European laboratories a set of 4 samples (2 soil and 2 waste samples) was analysed to determine performance characteristics for different combinations of digestion and detection methods. With the procedures prescribed by the new European standard (EN 15192) acceptable results were obtained for both soil samples and one of the waste samples (sludge). However, for the second waste sample (fly ash) a large deviation in analytical results was observed. This indicates that particularly for waste materials a possible occurrence of strong matrix effects has to be considered and supplementary quality control data are needed in order to assess the validity of analytical results. The accuracy of the determination of Cr(vi) in solid matrices remains a challenging field in terms of maximum extraction efficiency and minimum species interconversion.     

Interlaboratory evaluation of an extraction and fluorescence method for the determination of trace beryllium in soils

Analytical methods for the determination of trace beryllium in soils are needed so that anthropogenic sources of this element can be distinguished from native (background) levels of beryllium. In this work, a collaborative interlaboratory evaluation of a new extraction and fluorescence-based procedure for determining beryllium in soil samples was carried out to fulfil method validation requirements for ASTM International voluntary consensus standard test methods. A Canadian reference material, CCRMP Till-1 soil, with a background beryllium concentration of 2.4 microg g(-1), was selected for study. This certified reference material (CRM) was spiked and homogenized with varying levels of beryllium oxide in order to give batches of material with beryllium concentrations of 4.36 +/- 0.69, 11.5 +/- 0.7, 124 +/- 7 and 246 +/- 16 microg g(-1) (+/- values are standard deviations). In the interlaboratory study (ILS), which was carried out in accordance with an applicable ASTM International standard practice (ASTM E691), samples of these spiked soils were subjected to extraction in dilute ammonium bifluoride at approximately 90 degrees C for 40 h. Fluorescence measurement of the extracted beryllium was carried out via detection using the high quantum yield fluorophore, hydroxybenzoquinoline sulfonate (HBQS). Interlaboratory precision estimates from six participating laboratories ranged from 0.048 to 0.103 (relative standard deviations) for the five different beryllium concentrations. Pooled bias estimates resulting from this ILS were between -0.049 and 0.177 for the various beryllium levels. These figures of merit support promulgation of the analytical procedure as an ASTM International standard test method.     

Prediction of PAH biodegradation in field contaminated soils using a cyclodextrin extraction technique

Biodegradation has been identified as a major loss process for organic contaminants in soils and, as a result, microbial strategies have been developed for the remediation of contaminated land. Prediction of the biodegradable fraction would be important for determining bioremediation end-points in the clean-up of contaminated land. The aim of this study was to investigate the ability of a cyclodextrin extraction to predict the extent to which polycyclic aromatic hydrocarbons (PAHs) would be degraded microbiologically in field contaminated soils; further testing the robustness and reproducibility of this extraction in chemically complex systems. Dichloromethane and hydroxypropyl-beta-cyclodextrin (HPCD) extractable fractions were measured together with the PAH biodegradable fraction in each of the six field contaminated soils. The amounts of PAHs degraded by the catabolic activity of the indigenous microflora in each of the soils were correlated with HPCD-extractable PAH concentrations. The regressions showed that the amounts of lower molecular weight PAHs extracted by the HPCD were not significantly (P > 0.05) different to the amounts that were degraded. However, higher molecular weight PAHs that were extracted by HPCD did differ significantly (P < 0.05) from the amounts degraded. Although the HPCD extraction did overestimate the microbially degradable fraction of the higher molecular weight PAHs, overall the correlations between the HPCD extractable fraction and the microbially degradable fraction were very close, with mean values of the slope of line for the six soils equalling 1. This study further describes the robust and reproducible nature of the aqueous-based soil extraction technique reliably measuring the extent to which PAHs will be microbially degraded in soil.     

Effect of ultrasonic agitation on the release of copper, iron, manganese and zinc from soil and sediment using the BCR three-stage sequential extraction

An ultrasonic bath and an ultrasonic probe have been used to develop rapid versions of the three-stage Community Bureau of Reference (BCR, now the Standards, Measurement and Testing Programme) sequential extraction procedure. The effect of the ultrasonic treatments on the extraction of copper, iron, manganese and zinc from a sewage sludge-amended soil has been assessed. Recoveries similar to those of conventional shaking (i.e., conventional value, +/- 30%) could generally be obtained for copper, manganese and zinc, but not for the important matrix element iron. With the use of compromise sonication conditions, steps 1, 2 and 3 of the sequential extraction (excluding the hydrogen peroxide digestion in step 3, which was not performed with sonication) could be completed in 3, 5 and 1 min, respectively, using the ultrasonic probe, and in 3, 1 and 1 h, respectively, using the bath. The extraction procedures developed using the soil performed well when applied to lake sediment BCR CRM 601. Analyte partitioning was generally similar to that obtained with mechanical shaking, and overall metal recoveries were 84-98% of those obtained with the conventional BCR protocol, except for copper extracted with the probe (74%). Poorer performance (analyte recoveries, 58-104%) was obtained when the methods were applied to an intertidal sediment. This highlights the difficulty of developing a version of the BCR extraction, with ultrasonic assistance, which gives a performance equivalent to conventional shaking when applied to different substrates.     

Assessment of soil screening levels due to ingestion and dermal absorption of chrysene and benzo[k]fluoranthene and appropriate remediation method for Dorson Abad

For years, the Dorson Abad region has been extremely polluted by Tehran Oil Refinery due to leaking from its underground pipelines, storage tanks, and evaporation ponds. To assess the concentrations of hazardous polycyclic aromatic hydrocarbon (PAH) compounds, soil samples were collected from the grounds at and adjacent to a polluted stream located in the study area. The samples were then analyzed, and the results revealed that 12 of the 16 USEPA PAHs were noticeably present in the soil, which, among them, benzo[k]fluoranthene and chrysene had the highest concentrations with averages of 357.17 and 173.38 mg/kg, respectively. A comparison of the obtained concentrations with the soil screening levels indicated that both benzo[k]fluoranthene and chrysene concentrations were substantially higher than EPA screening level values, signifying the necessity of soil remediation for these contaminants in the area. Techniques such as soil washing/flushing, high temperature thermal desorption, and solidification/stabilization were investigated for treatment of the contaminated soil; solidification/stabilization is recommended as an applicable and cost-effective remediation method for Dorson Abad due to the size of the region, relatively low cost of the binder (cement), and low volatility of benzo[k]fluoranthene and chrysene.     

Treatment technologies for PAH-contaminated sites: a critical review

To reduce environmental and human health risks of contaminated sites, having a comprehensive knowledge about the polycyclic aromatic hydrocarbon (PAH) removal processes is crucial. PAHs are contaminants which are highly recognized to pose threats to humans, animals, and plants. PAHs are hydrophobic and own two or more benzene rings, and hence are resistant to structural degradation. There are various techniques which have been developed to treat PAH-contaminated soil. Four distinct processes to remove PAHs in the contaminated soil, thought to be more effective techniques, are presented in this review: soil washing, chemical oxidation, electrokinetic, phytoremediation. In a surfactant-aided washing process, a removal rate of 90% was reported. Compost-amended phytoremediation treatment presented 58–99% removal of pyrene from the soil in 90 days. Chemical oxidation method was able to reach complete conversion for some PAHs. In electrokinetic treatment, researchers have achieved reliable results in removal of some specific PAHs. Researchers’ innovations in novel studies and advantages/disadvantages of the techniques are also investigated throughout the paper. Finally, it should be noted that an exclusive method or a combination of methods by themselves are not the key to be employed for remediation of every contaminated site but the field characteristics are also essential in selection of the most appropriate decontamination technique(s). The remedy for selection criteria is based on PAH concentrations, site characteristics, costs, shortcomings, and advantages.     

Air quality assessment of benzo(a)pyrene from asphalt plant operation

A study has been carried out to assess the contribution of Polycyclic Aromatic Hydrocarbons (PAHs) from asphalt plant operation, utilising Benzo(a)pyrene (BaP) as a marker for PAHs, to the background air concentration around asphalt plants in the UK. The purpose behind this assessment was to determine whether the use of published BaP emission factors based on the US Environmental Protection Agency (EPA) methodology is appropriate in the context of the UK, especially as the EPA methodology does not give BaP emission factors for all activities. The study also aimed to improve the overall understanding of BaP emissions from asphalt plants in the UK, and determine whether site location and operation is likely to influence the contribution of PAHs to ambient air quality. In order to establish whether the use of US EPA emissions factors is appropriate, the study has compared the BaP emissions measured and calculated emissions rates from two UK sites with those estimated using US EPA emission factors. A dispersion modelling exercise was carried out to show the BaP contribution to ambient air around each site. This study showed that, as the US EPA methodology does not provide factors for all emission sources on asphalt plants, their use may give rise to over- or under-estimations, particularly where sources of BaP are temperature dependent. However, the contribution of both the estimated and measured BaP concentrations to environmental concentration were low, averaging about 0.05 ng m(-3) at the boundary of the sites, which is well below the UK BaP assessment threshold of 0.25 ng m(-3). Therefore, BaP concentrations, and hence PAH concentrations, from similar asphalt plant operations are unlikely to contribute negatively to ambient air quality.     

Determination of petroleum hydrocarbons and polycyclic aromatic hydrocarbons in sludge from wastewater treatment basins

Screening by gas chromatography with flame ionization detection and gas chromatography-mass spectrometry has been carried out on sludge extracts of wastewater treatment basins. Soxhlet extraction with trichlorotrifluoroethane was applied. The yields for petroleum hydrocarbons and PAH recovery were high, usually in excess of 90%. The proposed investigations permit a quick assessment of petroleum pollutants in the environment.     

Characterizing soils for hazardous waste site assessments

This paper provides a review and justification of the minimum data needed to characterize soils for hazardous waste site assessments and to comply with the Comprehensive Environmental Response, Compensation and Liability Act (CERCLA). Scientists and managers within the regulatory agency and the liable party need to know what are the important soil characteristics needed to make decisions about risk assessment, what areas need remediation and what remediation options are available. If all parties involved in characterizing a hazardous waste site can agree on the required soils data set prior to starting a site investigation, data can be collected in a more efficient and less costly manner. Having the proper data will aid in reaching decisions on how to address concerns at, and close-out, hazardous waste sites.This paper was prepared to address two specific concerns related to soil characterization for CERCLA remedial response. The first concern is the applicability of traditional soil classification methods to CERCLA soil characterization. The second is the identification of soil characterization data type required for CERCLA risk assessment and analysis of remedial alternatives. These concerns are related, in that the Data Quality Objective (DQO) process addresses both. The DQO process was developed in part to assist CERCLA decision-makers in identifying the data types, data quality, and data quantity required to support decisions that must be made during the remedial investigation/feasibility study (RI/FS) process. Data Quality Objectives for Remedial Response Activities: Development Process (US EPA, 1987a) is a guidebook on developing DQOs. This process as it relates to CERCLA soil characterization is discussed in the Data Quality Objective Section of this paper.     

Surfer软件和AutoCAD在污染场地调查及风险评估中的应用

在场地调查和风险评估报告中需要描述污染物分布和确定土壤修复区域和范围，目前对此无统一的技术要求，不同案例使用的技术方法不同。今提出将 Surfer软件和 AutoCAD结合使用生成等值线图件，以及据此确定污染土壤修复范围的方法，并基于某搬迁化工厂初步土壤调查及风险评估的案例介绍了操作步骤。旨在介绍2个专业软件联用的新功能的开发和使用技巧，为编制场地调查和风险评估报告提供一种便捷、易操作的工作方法。     

某农药厂周边空气毒死蜱污染状况及健康风险评价

为了研究某农药厂毒死蜱生产对周围人群产生的潜在健康风险,在农药厂周围村庄设置采样点,采用大流量大气采样器采集大气样本,索式提取/气相色谱法分析毒死蜱浓度。结果表明,大气气溶胶中毒死蜱的质量浓度为0.2~189 ng/m3,大气颗粒物中毒死蜱浓度较低,质量浓度为ND~3.50 ng/m3。基于美国环保局推荐的健康风险评价方法计算结果表明,大气毒死蜱暴露对于儿童和成人的非致癌风险控制在EPA推荐的可接受风险水平。     

Development and application of microwave assisted extraction (MAE) for the extraction of five polycyclic aromatic hydrocarbons in sediment samples in Johannesburg area, South Africa

A microwave-assisted extraction (MAE) method was verified and applied for the extraction of polycyclic aromatic hydrocarbons (PAHs) in sediment samples. Soxhlet extraction was used as the reference method. The optimum MAE was carried out with 20 mL of hexane/acetone (1:1, v/v) mixture in a 1-g sample at 250 W for 20 min. Soxhlet extraction was carried out with 250 mL of dichloromethane:hexane (1:1, v/v) mixture in a 15-g sample for 24 h in a water bath maintained at 60 °C. The collected extracts were both cleaned up, reduced to 1 mL under nitrogen and then injected into an HPLC fluorescence. To increase the sample throughput, simultaneous MAE was performed. The obtained percentage recoveries ranged from 61 to 93 and 88–98 for MAE and SE, respectively. The optimised MAE method was validated using certified reference material. It was then applied to real sediment samples from in and around the greater Johannesburg area. The sediments from Jukskei River were found to be the most polluted while Hartbeespoort Dam sediments were found to be least polluted. The overall order of concentrations for the studied PAHs per site was as follows: Jukskei River?>?Kempton Park?>?Centurion Dams?>?Natalspruit River (PIT)?>?Hartbeespoort Dam.     

化工厂场地酸化土壤工程化中和修复案例研究

对江苏某化工厂酸化地块进行了氧化钙中和修复工程研究。Ⅰ、Ⅱ、Ⅲ号地块剖面混合土样pH值分别为3.56、4.68和4.74,土壤修复目标定在pH值为6~8基本近中性。通过室内试验确定Ⅰ、Ⅱ、Ⅲ号地块土壤生石灰掺混比例为0.5%、0.3%和0.3%;现场中试后Ⅰ、Ⅱ、Ⅲ号地块石灰掺混比例调整为0.7%、0.35%和0.3%;中试结果用于场地机械搅拌工程修复,修复过程中定期随机采样对中和效果进行连续监测。监测结果基本达标后请第三方对修复效果进行评估,最后土壤回填压实。修复结果表明借助于科学的石灰添加量和工程机械混合措施,能快速有效地修复酸化地块土壤。     

Assessment of metal contamination using X-ray fluorescence spectrometry and the toxicity characteristic leaching procedure (TCLP) during remediation of a waste disposal site in Antarctica

The remediation of the Thala Valley landfill, Casey Station, East Antarctica, is part of efforts to clean-up contaminated sites associated with the Australian Antarctic Program. These sites, ranging from abandoned rubbish dumps to fuel spills, are contaminated principally with metals and petroleum hydrocarbons. Remediation success depends on accurate, cost-effective and timely--fit-for-purpose--chemical analysis of soil and water samples from the site, which is required to guide excavation, the in situ or off-site treatment and disposal of contaminated material, and to validate satisfactory remediation. Owing to the remote location of Antarctica, it is necessary to carry out chemical analyses on-site. Waste and soil contaminated with Pb, Zn, Cd, and Cu were excavated from Thala Valley for removal to Australia, treatment and disposal. Analysis of total metal concentrations in soil was performed at Casey Station with a transportable energy dispersive X-ray fluorescence (EDXRF) spectrometer. Soil samples were prepared using a simple size-fractionation method to expedite sample throughput. A method for assessing contaminant mobility in solid waste (toxicity characteristic leaching procedure, TCLP) was also used to characterise soil. Although this was more labour-intensive and time-consuming than the total metals analysis, it was of great utility because leachable metals were often significant determinants in the assessment of contaminated soil. The combined data helped managers during remediation, directing excavation and allowing waste to be classified for treatment and disposal before its return to Australia.     

Influence of solvent and soil type on the pressurised fluid extraction of PAHs

Pressurised fluid extraction (PFE) of polycyclic aromatic hydrocarbons (PAHs) from a certified reference material (CRM) 524 has been firstly optimised following a central composite design. The instrumental parameters of the PFE (pressure, temperature, extraction time and number of solvent cycles) were studied in order to obtain maximum extraction yields. Neither pressure nor extraction time or temperature seemed to have any significant effect on the extraction yield, therefore one extraction cycle was enough to exhaustively extract all the PAHs from CRM 524. Once the instrumental conditions were established, the extraction yields obtained with eight different solvents or solvent mixtures [acetone, dichloromethane, acetonitrile, acetone-dichloromethane (1 + 1 v/v), acetone-isohexane (1 + 1 v/v), isohexane, methanol and toluene] from the CRM 524 were compared and showed that the best recoveries were obtained with acetone-isohexane (1 + 1 v/v). Finally, the effect of sand, silt, clay and the organic matter content of soil was investigated with respect to recovery of PAHs by PFE with different solvents or solvent mixtures for aged soil samples. In this case, eight soils with different sand, silt, clay and organic matter contents were slurry spiked with PAHs and aged for 19 days. Three aliquots of each slurry spiked soil were extracted with the previously mentioned solvents and the results were studied by means of principal component analysis (PCA) of the whole data set (soil composition, solubility parameter of the solvent and recoveries of all PAHs) and partial least squares (PLS). Clay and organic matter content and the squared solubility parameter have the highest correlation with the recovery of PAHs from soil samples.     

Fingerprinting of petroleum hydrocarbons (PHC) and other biogenic organic compounds (BOC) in oil-contaminated and background soil samples

Total petroleum hydrocarbons (TPH) or petroleum hydrocarbons (PHC) are one of the most widespread soil contaminants in Canada, the United States and many other countries worldwide. Clean-up of PHC-contaminated soils costs the Canadian economy hundreds of millions of dollars annually. In Canada, most PHC-contaminated site evaluations are based on the methods developed by the Canadian Council of the Ministers of the Environment (CCME). However, the CCME method does not differentiate PHC from BOC (the naturally occurring biogenic organic compounds), which are co-extracted with petroleum hydrocarbons in soil samples. Consequently, this could lead to overestimation of PHC levels in soil samples. In some cases, biogenic interferences can even exceed regulatory levels (300 μg g(-1) for coarse soils and 1300 μg g(-1) for fine soils for Fraction 3, C(16)-C(34) range, in the CCME Soil Quality Level). Resulting false exceedances can trigger unnecessary and costly cleanup or remediation measures. Therefore, it is critically important to develop new protocols to characterize and quantitatively differentiate PHC and BOC in contaminated soils. The ultimate objective of this PERD (Program of Energy Research and Development) project is to correct the misconception that all detectable hydrocarbons should be regulated as toxic petroleum hydrocarbons. During 2009-2010, soil and plant samples were collected from over forty oil-contaminated and paired background sites in various provinces. The silica gel column cleanup procedure was applied to effectively remove all target BOC from the oil-contaminated sample extracts. Furthermore, a reliable GC-MS method in combination with the derivatization technique, developed in this laboratory, was used for identification and characterization of various biogenic sterols and other major biogenic compounds in these oil-contaminated samples. Both PHC and BOC in these samples were quantitatively determined. This paper reports the characterization results of this set of 21 samples. In general, the presence of petroleum-characteristic alkylated PAH homologues and biomarkers can be used as unambiguous indicators of the contamination of oil and petroleum product hydrocarbons; while the absence of petroleum-characteristic alkylated PAH homologues and biomarkers and the presence of abundant BOC can be used as unambiguous indicators of the predominance of natural organic compounds in soil samples.     

PAHs in the urban air of Sarajevo: levels,sources, day/night variation,and human inhalation risk

Polycyclic aromatic hydrocarbons (PAHs) are organic pollutants derived from pyrolysis and pyrosynthesis processes. Industrial activity, motor vehicle emission, and domestic combustion are the main sources of PAHs in the urban atmosphere. In this work, samples collected during the day and night in the urban area of Sarajevo are analyzed separately for gaseous and particle-bound PAHs; the possible origin of PAHs at the receptor site was suggested using different methods applied to the solid phase and to the total PAHs (gaseous + particulate phase). Finally, the risk level in Sarajevo associated to the carcinogenic character of the studied PAHs has been assessed. The result of this study suggests that (a) the total PAH concentrations were higher than those reported in other European cities; (b) the PAH daytime concentrations are higher than nocturnal concentrations: the sum of the PAH day/night ratios is 1.52 (gas) and 1.45 (particle phase); (c) stationary combustion and traffic were suggested to be the main sources of PAHs; (d) the average particle-bound benzo(a)pyrene (BaP) concentration (5.4 ng/m³) is higher than EU target annual value (1 ng/m³); and (e) PAH cancer risk exceeds the carcinogenic benchmark level recommended by the EPA mainly due to BaP during both the day and night periods.     

微波提取高效液相色谱法测定土壤中15种痕量多环芳烃

采用微波提取结合高效液相色谱技术测定了土壤中15种PAHs的含量.比较了用微波提取、索氏提取和超声萃取3种土壤样品的前处理方法对多环芳烃测定的影响,考察了色谱柱的性能、梯度洗脱条件的优化、荧光检潮波长程序变换及柱温等因素对15种PAHs组分之同分离的影响.经优化后的HPLC方法对15种PAHs的最低检测限为0.10～0.80 μg/kg,相对标准偏差为0.60%～4.60%,方法的回收率为58.1%～97.8%.实验结果表明,该方法兵有高效、快速、灵敏等特点,可以用于环境土壤样品中痕量PAHs的检测.