Sulfamethoxazole removal from polluted water by immobilized photocatalysis

The photocatalytic activity of TiO₂ deposits (Degussa P25 and Millennium PC500) has been studied using sulfamethoxazole (SMX) as a model water pollutant and a UV fluorescent lamp as a light source (365 nm). Both catalysts have shown very similar properties in the photocatalytic degradation of SMX. Special attention has been given to the effect of the irradiation time, pH, and pollutant concentration. No mass-transfer limitations are observed. The degradation of SMX is accelerated at low concentration, and the photocatalytic degradation kinetics obey the Langmuir–Hinshelwood model, allowing the adsorption and apparent rate constants to be determined for both catalysts.     

Preparation and characterization of a new TiO2/SiO2 composite catalyst for photocatalytic degradation of indigo carmin

The TiO₂/SiO₂ composite was prepared by means of the SiO₂-particle-entrapment method. The FTIR data showed the presence of Si–O–Ti stretching vibration band at 970 cm⁻¹ in the TiO₂/SiO₂ composite, suggesting a reaction between TiO₂ and silica on the TiO₂ particle surface during the silicagel formation around the TiO₂ particles. The photocatalytic efficiency of TiO₂ immobilized in silicagel was compared with that of the conventional TiO₂ Degussa P25 catalyst. For this purpose, the degradation of indigo carmin (IC) dye was used as model molecule in the tests. The effect of operational parameters such as catalyst loading and dye concentration on the photocatalytic degradation of the model dye was investigated. The rate of degradation increased with increasing catalyst loading, and when the concentration of the dye decreases.     

Photocatalytic mineralization of a water pollutant,Sunset Yellow dye by an advanced oxidation process using a modified catalyst

ZnS-loaded TiO₂ (ZnS–TiO₂) was synthesized by a sol–gel method. The catalyst was characterized by using different techniques (XRD, HR-SEM, EDS, DRS, PL, XPS, and BET methods). The photocatalytic activity of ZnS–TiO₂ was investigated for the degradation of Sunset Yellow FCF (SY) dye in an aqueous solution using ultraviolet light. ZnS–TiO₂ is found to be more efficient than prepared TiO₂, TiO₂–P25, TiO₂ (Merck), and ZnS at pH 7 for the mineralization of SY. The effects of operational parameters such as the amount of photocatalyst, dye concentration, and initial pH on photo mineralization of SY have been analyzed. The mineralization of SY has been confirmed by chemical oxygen demand measurements. The catalyst is found to be reusable.     

Comparison of photoelectrochemical properties of TiO2-nanotube-array photoanode prepared by anodization in different electrolyte

Self-organized, well-crystallized and high aspect-ratio TiO₂ nanotube arrays (TNAs) have been prepared by anodic oxidation in dimethyl sulfoxide (DMSO) containing 5 wt% HF at 40 V (vs. Pt). A 50 h anodization results in a nanotube arrays approximately 19.4 μm in length, referred as long tube. As a comparison, the short titania nanotube arrays, about 500 nm in length, was obtained by anodization in HF aqueous solution, referred as short tube. Different characterization techniques (viz. FESEM, TEM, XRD and DRS) are used to study the nanotubular microstructure. The morphology of the nanotube electrodes shows an evident influence on their photocatalytic (PC) and photoelectrochemical reactivity. The long tube reveals enhanced photocurrent response and PC degradation efficiency of organic compounds. The kinetic constant of PC degradation of methylic orange (MO) for long tube electrode is found 1.55 times as high as the short tube. A significant photoelectrochemcial synergetic effect in MO degradation was observed on the long tube electrode and the photoelectrocatalytic (PEC) degradation of MO on long tube is 27% higher than its PC process.     

Photocatalytic degradation of phenol with mesoporous TiO2?xBx

We report a facile approach for preparing mesoporous boron-doped TiO₂ materials by combining the sol?Cgel process with the dehydration of glucose. Specifically a high surface carbon material was formed by dehydration of glucose, then used as template. This material and the TiO₂ dry gel were calcinated to produce porous TiO₂. The as-synthesized boron-doped TiO₂ was in pure anatase crystallite phase with high surface area. X-ray photoelectron spectroscopy (XPS) results showed that boron was incorporated into the anatase TiO₂ lattice to form TiO_2?xB_x. The absorption spectra of TiO_2?xB_x extended into the visible region to 460?nm. The TiO_2?xB_x exhibited much higher photocatalytic activity on phenol degradation than pure TiO₂. It showed that the phenol degradation by-products of TiO_2?xB_x were different from that of pure TiO₂. Mechanism of the photocatalytic degradation of phenol at TiO_2?xB_x was also proposed.     

Solar photocatalytic decomposition of two azo dyes on multi-walled carbon nanotubes (MWCNTs)/TiO<Subscript>2</Subscript> composites

Multi-walled carbon nanotubes (MWCNTs)/TiO₂ composite photocatalysts with high photoactivity were prepared by sol-gel process and further characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared (FT-IR), and UV-vis absorption spectra. Compared to pure TiO₂, the combination of MWCNTs with titania could cause a significant absorption shift toward the visible region. The photocatalytic performances of the MWCNTs/TiO₂ composite catalysts were evaluated for the decomposition of Reactive light yellow K-6G (K-6G) and Mordant black 7 (MB 7) azo dyes solution under solar light irradiation. The results showed that the addition of MWCNTs enhanced the adsorption and photocatalytic activity of TiO₂ for the degradation of azo dyes K-6G and MB 7. The effect of MWCNTs content, catalyst dosage, pH, and initial dye concentration were examined as operational parameters. The kinetics of photocatalytic degradation of two dyes was found to follow a pseudo-first-order rate law. The photocatalyst was used for seven cycles with photocatalytic degradation efficiency still higher than 98%. A plausible mechanism is also proposed and discussed on the basis of experimental results.     

Structural effect on photocatalytic degradation of metallised azo dyes in aqueous TiO2 suspension

Three metallised azo dyes were investigated under TiO₂‐photocatalytic and photosensitised conditions in aqueous buffering solutions. The degradation follows apparent first‐order kinetics. The size and strength of intramolecular conjugation determine the light‐fastness of the investigated dyes. Compared with ¹O₂ produced in photosensitised process, the more powerful *OH radicals in TiCO₂ photocatalytic process are highly reactive towards the investigated azo dyes. And as a result, the TiO₂‐photocatalysis makes little less distinction in the degradation kinetic data of the azo dyes compared with the photosensitised degradation of them.     

Preparation of effective TiO<Subscript>2</Subscript>/Bi<Subscript>2</Subscript>O<Subscript>3</Subscript> photocatalysts for water treatment

Photocatalytic oxidation using semiconductors is one of the advanced oxidation processes for degradation of organic pollutants in water and air. TiO₂ is an excellent photocatalyst that can mineralize a large range of organic pollutants such as pesticides and dyes. The main challenge is to improve the efficiency of the TiO₂ photocatalyst and to extend TiO₂ light absorption spectra to the visible region. A potential solution is to couple TiO₂ with a narrow band gap semiconductor possessing a higher conduction band such as bismuth oxide. Therefore, here we prepared Bi₂O₃/TiO₂ heterojunctions by the impregnation method with different Bi/Ti ratio. The prepared composites have been characterized by UV–Vis diffused reflectance spectra and X-ray diffraction. The photocatalytic activity of the heterojunction has been determined from the degradation of orange II under visible and UV light. Results show that Bi₂O₃/TiO₂ heterojunctions are more effective than pure TiO₂-anatase under UV-A irradiation, with an optimum for the Bi/Ti ratio of 5 %, for the photocatalytic degradation of Orange II. However, the photocatalytic activity under irradiation at λ higher than 420 nm is not much improved. Under UV–visible radiation, the two semiconductors are activated. We propose a mechanism explaining why our products are more effective under UV–visible irradiation. In this case the charge separation is enhanced because a part of photogenerated electrons from the conduction band of TiO₂ will go to the conduction band of bismuth oxide. In this composite, titanium dioxide is the main photocatalyst, while bismuth oxide acts as adsorbent photosensitizer under visible light.     

Photodegradation of an azo dye by silver-doped nano-particulate titanium dioxide

The synthesis of silver doped nano-particulate titanium dioxide (Ag/TiO₂) using a microemulsion method and an investigation of its photocatalytic activity for the degradation of Acid Red 27 in distilled water under UV-irradiation is reported. The prepared Ag/TiO₂ is characterized using transmission electron microscopy, X-ray diffraction, and energy-dispersive X-ray spectroscopy. The size of the Ag nanoparticles is around 5–15?nm, with almost uniform distribution on the TiO₂ particles. The efficiency of the photocatalytic process is evaluated to establish the optimum conditions, found to be at 2?wt% of Ag loading on TiO₂, catalyst dosage of 400?mg?L^?1, and calcination temperature of 300°C. Complete decolorization of the dye solution on Ag/TiO₂ was observed in 20?min of UV irradiation in the optimum conditions.     

Photocatalytic degradation of organic dyes by Er<Superscript>3+</Superscript>:YAlO<Subscript>3</Subscript>/TiO<Subscript>2</Subscript> composite under solar light

In this work, Er³⁺:YAlO₃/TiO₂ composite was synthesized by a ultrasonic dispersion and liquid boil method. The Er³⁺:YAlO₃/TiO₂ composite and pure TiO₂ powder were characterized by XRD. The degradation of different organic dyes was used to evaluate the photocatalytic activity of the Er³⁺:YAlO₃/TiO₂ composite. It is found that the photocatalytic activity of Er³⁺:YAlO₃/TiO₂ composite is much higher than that for the similar system with only TiO₂. Moreover, this Er³⁺:YAlO₃/TiO₂ composite provides a new way to take advantage of TiO₂ in sewage treatment aspects using solar light.     

TiO2 photocatalyzed degradation of diazinon in an aqueous medium

The photocatalytic degradation of diazinon was studied over TiO₂ catalysts. The kinetics obtained demonstrated that powder titania (t_1/2 = 9.7 min) was more efficient compared to pure titania thin film catalysts (t_1/2 = 29.4 min). Mineralization of organic carbon to CO₂ after 360 min of irradiation was found to be 75% while heteroatoms (P, S, N) were mineralized into phosphate, sulfate and nitrate ions, respectively. A microtox test was performed to evaluate the toxicity of solutions treated by catalysts. Illumination of diazinon in the presence of TiO₂ gave rise to several intermediates that have been identified by means of solid phase extraction and gas chromatography-mass spectrometry, while a simple degradation pathway is proposed.     

Removal of rhodamine B from aqueous solution by BiPO4 hierarchical architecture

Hexahedron-like BiPO₄ microcrystals were sucessfully synthesized via a template-free hydrothermal method. The resulting samples were characterized by Xray diffraction (XRD), field-emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM) and UV-vis spectroscopy. The BiPO₄ samples were of pure monoclinic phase, and the initial amount of PO_3–4 during synthesis did not show obvious effect on the phase properties of the materials. The hexahedron-like BiPO₄ microcrystal had explicitly cut edges, and its thickness was about 1 μm. The photocatalytic performance of the BiPO₄ catalysts was evaluated by photodegradation of RhB under UV light irradiation with commerial Degussa P25 TiO₂ as reference. Compared with P25, the BiPO₄ catalysts displayed higher photocatalytic activity, with 98.7% of RhB degraded during 60-min experiment. Cost evaluation analysis was adopted to describe the energy consumption of the degradation process, and the results suggested the potential application of this material in the field of dye-contaminated wastewater treatment or environmental matrices remediation.     

Degradation of azo dye reactive violet 5 by TiO2 photocatalysis

The photocatalytic degradation of hydrolyzed reactive violet 5 (RV5) using titanium dioxide (TiO₂) was investigated in this study. The effects of various factors including the amount of photocatalyst, RV5 concentration, light intensity, and pH on photocatalytic degradation were evaluated. The photodegradation efficiency was 90% after 20 min of irradiation and reached nearly 100% after 80 min under the condition of pH 4 and temperature of 25°C. The decolorization rate typically followed first-order reaction, and increased markedly with increasing amount of photocatalyst, pH as well as light intensity. The total mineralization, based on total organic carbon (TOC) concentration was 53% after 20 min of UV light exposure and approached nearly 100% after 140 min. The final mineralization product was formylformamide. The photodegradation was faster than the mineralization, indicating that the intermediate products of decolorization were resistant to photodegradation. In this study, we found that toxicity of RV5 significantly decreased after decolorization. Our study suggests that the photocatalytic degradation treatment of RV5 with TiO₂ in wastewater is a simple and fast method.     

Enhancement of photoelectrocatalytic properties of stainless-steel/TiO2 electrode by applying mid-frequency electric field

Nanocrystalline TiO₂ films were prepared by magnetron sputtering technique on stainless-steel substrates. The as-deposited TiO₂ thin films were in anatase structure with smooth surface morphology. Decomposition of methyl orange was used to measure the photoelectrocatalytic activity. The degradation rate of methyl orange increased with externally applied potential. To further accelerate the photocatalytic reaction, a novel method was employed by applying an external electric field in the mid-frequency domain. The fastest photocatalytic degradation rate of methyl orange was obtained when the frequency was maintained at 20 kHz with an external anodic bias at 3.0 V.     

Photocatalytic removal of nitrogen oxides via titanium dioxide

We studied the removal of nitrogen oxides pollutants via TiO₂ Degussa P25 powder by photocatalysis. Parameters such as mass of catalyst, geometric irradiated surface, catalyst morphology, and thermal treatment were tested to explain the photocatalytic concentration decrease of nitrogen oxides. According to our working conditions, the conversion rates increased until an optimal value of the TiO₂ weight, 35% of NO concentration and around 20% of NOx, was decomposed by the photocatalysis. The NOx removal increased proportionally with the irradiated geometric surface. The structural transformation of anatase to rutile performed by thermal treatment involved the decrease of the photocatalytic activity.     

Solar photocatalytic degradation of the herbicide isoproturon on a Bi–TiO2/zeolite photocatalyst

The photocatalytic degradation of the herbicide isoproturon under solar light was investigated in aqueous solution containing a Bi–TiO₂/zeolite photocatalyst. The catalysts were characterized using X-ray diffraction, UV-Vis diffuse reflectance spectroscopy, Fourier transform-infrared spectroscopy, scanning electron microscopy, and transmission electron microscopy. The effect of Bi–TiO₂ loading onto the zeolite support and influence of the parameters such as catalyst amount, pH, and initial concentration of isoproturon on the degradation rate were evaluated. The recycling ability of the catalyst was found to be sustainable for elongated periods. The high activity of the Bi–TiO₂/zeolite was attributed to its absorptivity of visible light and its high adsorption capacity for the pollutant molecules.     

Photodegradation of Ibuprofen,Cetirizine, and Naproxen by PAN-MWCNT/TiO<Subscript>2</Subscript>–NH<Subscript>2</Subscript> nanofiber membrane under UV light irradiation

Background

In this study, the photodegradation of three pharmaceuticals, namely Ibuprofen (IBP), Naproxen (NPX), and Cetirizine (CIZ) in aqueous media was investigated under UV irradiation. The photocatalyst used in this work consists of surface functionalized titanium dioxide (TiO₂–NH₂) nanoparticles grafted into Polyacrylonitrile (PAN)/multi-walled carbon nanotube composite nanofibers. Surface modification of the fabricated composite nanofibers was illustrated using XRD, FTIR, and SEM analyses.

Results

Sets of experiments were performed to study the effect of pharmaceuticals initial concentration (5–50 mg/L), solution pH (2–9), and irradiation time on the degradation efficiency. The results demonstrated that more than 99% degradation efficiency was obtained for IBP, CIZ, and NPX within 120, 40, and 25 min, respectively.

Conclusions

Comparatively, the photocatalytic degradation of pharmaceuticals using PAN-CNT/TiO₂–NH₂ composite nanofibers was much more efficient than with PAN/TiO₂–NH₂ composite nanofibers.

     

Titanium dioxide photocatalysis for pharmaceutical wastewater treatment

Heterogeneous photocatalysis using the semiconductor titanium dioxide (TiO₂) has proven to be a promising treatment technology for water purification. The effectiveness of this oxidation technology for the destruction of pharmaceuticals has also been demonstrated in numerous studies. This review highlights recent research on TiO₂ photocatalytic treatment applied to the removal of selected pharmaceuticals. The discussions are tailored based on the therapeutic drug classes as the kinetics and mechanistic aspects are compound dependent. These classes of pharmaceuticals were chosen because of their environmental prevalence and potential adverse effects. Optimal operational conditions and degradation pathways vary with different pharmaceutical compounds. The main conclusion is that the use of TiO₂ photocatalysis can be considered a state-of-the-art pharmaceutical wastewater treatment methodology. Further studies are, however, required to optimize the operating conditions for maximum degradation of multiple pharmaceuticals in wastewater under realistic conditions and on an industrial scale.     

Fabrication and photocatalytic ability of an Au/TiO<Subscript>2</Subscript>/reduced graphene oxide nanocomposite

A new type of Au/TiO₂/reduced graphene oxide (RGO) nanocomposite was fabricated by the hydrothermal synthesis of TiO₂ on graphene oxide followed by the photodeposition of Au nanoparticles. Transmission electron microscopy images showed that Au nanoparticles were loaded onto the surface of both TiO₂ and RGO. Au/TiO₂/RGO had a better photocatalytic activity than Au/ TiO₂ for the degradation of phenol. Electrochemical measurements indicated that Au/TiO₂/RGO had an improved charge transfer capability. Meanwhile, chemiluminescent analysis and electron spin resonance spectroscopy revealed that Au/TiO₂/RGO displayed high production of hydrogen peroxide and hydroxyl radicals in the photocatalytic process. This high photocatalytic performance was achieved via the addition of RGO in Au/TiO₂/RGO, where RGO served not only as a catalyst support to provide more sites for the deposition of Au nanoparticles but also as a collector to accept electrons from TiO₂ to effectively reduce photogenerated charge recombination.

Open image in new window

     

Enhanced photocatalytic activity of electrospun TiO2/polyacrylonitrile membranes in a crossflow reactor using dual lights

Photocatalytic membranes reactors have become one of the most efficient technologies to treat polluted waters. However, a major drawback is the unilateral irradiation of the membrane, where only one side of the membrane is exploited. To overcome this issue, we developed a reactor where the membrane can be irradiated on both sides. Polyacrylonitrile membranes containing different amounts of TiO₂ nanoparticles up to 60% were first prepared by electrospinning. These membranes were used in a 3D-printed crossflow photocatalytic membrane reactor for the degradation of methylene blue under different combinations of lights. The use of both sides of the photocatalytic membrane significantly enhanced the photocatalytic activity for the decolorization of methylene blue in water. The prepared membranes showed the best decolorization rate for a loading of 60% of TiO₂ and the use of dual ultraviolet lights, where the methylene blue solution was completely discolored after 90 min. This is the first report of a such system configuration, and this new irradiation concept is promising for photocatalytic membrane reactions and water cleaning.