铝粉爆炸无火焰泄压技术及装备研究

为有效防止粉尘爆炸泄爆引起的二次爆炸及火灾问题,基于泄压理论、消火机理,设计开发无火焰泄压装置,装置主要由消火结构、底座、爆破片及夹持机构组成,消火结构由不锈钢金属丝网组成。选择铝粉尘为测试粉尘,通过自建除尘系统试验平台进行试验研究。结果表明:无火焰泄压装置可成功阻止火焰传播,装置释放的冲击波在5 m外均小于5 kPa,除尘系统内部最大泄爆压力为0.1 MPa,装置前端火焰传播速度均大于100 m/s。     

连通容器气体密闭爆炸与泄爆过程的实验研究

利用球型容器与管道组合,开展连通容器气体爆炸与泄爆实验,分析连通条件下,火焰在管道中的传播过程及其对起爆容器和传爆容器的压力影响。实验结果表明:连通容器气体爆炸中,火焰从起爆容器到传爆容器传播经历了一段不断加速,但加速度不断减小的过程;泄爆过程中,火焰传播过程与密闭爆炸时基本一致。管道中火焰加速传播,使得传爆容器的爆炸压力和强度相较于作为起爆容器时均明显增加,危险更大,采用与起爆容器相同的泄爆面积,无法满足对连通容器中传爆容器的泄爆。同时,泄爆是一个快速的能量泄放过程应选择合理的泄爆方式,防止二次危害。     

Experimental study on water sealing of fire barriers and explosion venting of large-scale pipeline with low-concentration gas

Low-concentration gas transported in pipelines may lead to explosion accidents because gas with a concentration of less than 30% is prone to explode. To reduce the incidence of gas explosions, water sealing of fire barriers is implemented, and explosion venting devices are installed along the pipeline. To investigate their suppression effect on low-concentration gas explosion, experiments using methane–air premixed gas under different conditions were implemented on a DN500 pipeline test system. The effects of three types of explosion venting forms (rupture disc, asbestos board, and plastic film) on explosion overpressure and flame were compared and analysed. Results show that the rupture disc, asbestos board, and plastic film can achieve adequate explosion venting, causing the peak decay rates of explosion overpressure to reach 82.37%, 81.72%, and 90.79%, respectively. The foregoing indicates that the greater the static activation pressure of the explosion venting form, the higher the peak explosion overpressure at each measurement point. Moreover, the shorter the explosion flame duration, the greater the flame propagation velocity. The research results provide an essential theoretical foundation for the effective suppression of gas explosion accidents in the process of low-concentration gas transportation.     

泄爆口参数对氢气火焰传播过程影响的数值模拟*

为了减少管内气体爆炸造成的损失与破坏,基于大涡模拟LES模型和Zimont燃烧模型,研究泄爆尺寸(直径为40,60,80 mm)和泄爆位置(侧方距点火端1,3,5 m)等泄爆条件对受限空间中氢气燃爆特性的影响。研究结果表明:大孔径泄爆口更好的排放效果造成火焰锋面在通过泄爆口时发生严重畸变,而泄爆口与点火端距离的增加则会削弱火焰锋面畸变的程度,且不同尺寸泄爆口产生的泄压效果差异较大。因此,应考虑将合适尺寸的泄爆口设置于靠近易燃点处。通过探索不同泄爆孔径与泄爆口位置对氢气火焰传播的影响规律,可为实际应用中的安全泄爆起到指导性作用。     

多层丝网结构抑制瓦斯爆炸传播的数学模型

在多层金属丝网结构对瓦斯爆炸传播的抑制作用机理上建立了多层丝网结构抑燃抑爆的数学模型,表述了火焰传播参数、爆炸反应波参数与丝网结构参数之间的关系.     

多孔球形材料阻火抑爆性能影响因素数值模拟研究

为探究影响多孔球形材料阻火抑爆性能的主要因素,采用气体爆炸模拟软件FLACS建立多孔球形结构中湍流燃烧模型,对填充多孔球形材料后丙烷/空气预混气体燃烧爆炸过程进行数值模拟。研究结果表明:多孔球形材料能够有效衰减爆燃压力波、阻隔火焰传播,起到阻火抑爆作用,且压力波衰减程度和火焰阻隔效果与多孔球形材料的尺寸、孔径及填充密度密切相关。当多孔球形材料的直径为25 mm、孔径为3 mm、填充密度为20层时,压力波衰减程度最大,火焰阻隔效果最明显,说明直径和孔径越小,填充密度越大,材料的阻火抑爆性能越强。     

Prediction of the relief of gas explosion in a tubular vessel by venting using a mathematical model

The relief of a gas explosion in a tubular vessel by venting can be predicted by using a mathematical model. In this model, the flame acceleration is represented by an increase in the burning velocity. The movement of a vent cover can be included. The model assumes that the vent is blocked by the vent cover prior to the explosion. the venting ratio was the most influential parameter in terms of relieving the pressure. In the case of a large venting ratio, the flame acceleration made a highly significant contribution, whereas for small venting ratios, the weight of the vent cover contributed to the relief more than the flame acceleration. When the pressure is required to be reduced significantly, the venting ratio, the vent open pressure and the weight of the vent cover must all be reduced.     

Dynamics of explosion venting in a compartment with methane-air mixtures

A series of experiments on explosion venting of methane-air mixtures are performed to scrutinize the pressure evolution as well as the flame dynamics and morphology at various vent conditions. Specifically, a premixed flame is ignited at the center of a polycarbonate cylindrical compartment, with three various vent areas considered (with negligible vent relief pressure). As expected, the highest maximum pressure is observed in the case of the smallest vent area. For all three cases, the pressure evolution experiences two major peaks, associated with the instants (i) when the maximum flame front surface area in the chamber is reached and (ii) when an external explosion occurs due to venting of unburned gases, respectively. For the fuel-rich mixtures, a flashback is observed subsequent to the external explosion, constituting the key outcome of the present work. The flame tip velocities show two general trends, namely, exponential acceleration towards the vent, while a flame propagates towards the blocked side of the compartment with no acceleration, which is important to know in the fire/explosion safety applications.     

Large eddy simulation and experimental study of the effect of wire mesh on flame behaviours of methane/air explosions in a semi-confined pipe

Preventing the propagation of flames in a pipeline is an effective measure for avoiding gas explosion accidents and reducing losses. To evaluate the effect of wire mesh, acting as a porous media, experimental and simulation studies are conducted to determine the influence of the wire mesh on the dynamics of premixed methane/air flame propagation in a semi-closed pipe. Four different kinds of wire mesh with different numbers of layers are chosen in the experiments and simulation, and the mechanism of wire mesh quenching of the flame is investigated. The experimental and simulation results are consistent. Flames are quenched when 4 layers of 40-mesh or 3 layers of 60-mesh wire mesh are used; however, once the flame propagates through the wire mesh, the risk of methane combustion may increase. The wire mesh becomes the key factor causing flame folds and acceleration, and the greater the number of layers or the larger the mesh size is, the more obvious the folds after the flame passes through the wire mesh. Moreover, the combination of heat absorption and disruption of the continuous flame surface by the mesh causes flame quenching. Wire mesh can effectively attenuate the flame temperature during premixed flame propagation in a pipe, and the attenuated maximum rate reaches approximately 79% in the case of adding 3 layers of 60-mesh wire mesh.     

Application and effect of negative pressure chambers on pipeline explosion venting

Explosion venting is a frequently-used way to lower explosion pressure and accident loss. Recently, studies of vessel explosion venting have received much attention, while little attention has been paid to pipe explosion venting. This study researched the characteristics of explosion venting for Coal Bed Methane (CBM) transfer pipe, and proposed the way of explosion venting to chamber in order to avoid the influence of explosion venting on external environment, and investigated the effects of explosion venting to atmosphere and chamber. When explosion venting to atmosphere, the average explosion impulse 4.89 kPa s; when explosion venting to 0 MPa (atmospheric pressure) chamber, average explosion impulse is 7.52 kPa s; when explosion venting to −0.01 MPa chamber, explosion flame and pressure obviously drop, and average explosion impulse decreases to 4.08 kPa s; when explosion venting to −0.09 MPa chamber, explosion flame goes out and average explosion impulse is 1.45 kPa s. Thus, the effect of explosion venting to negative chamber is far better than that to atmospheric chamber. Negative chamber can absorb more explosion gas and energy, increase stretch of explosion flame, and eliminate free radical of gas explosion. All these can promote the effect of explosion venting to negative chamber.     

Experimental study of the venting characteristics of dust explosion through a vent duct

To further understand the dynamic mechanism of dust explosion through a vent duct, we designed a small-scale cylindrical vessel connected with a vent duct and performed a dust explosion venting experiment under different opening pressures using corn starch as the explosive medium in this study. The results show that weakening effect of duct on venting is positively correlated with the opening pressure. The explosion pressure in the duct presents a three-peak-structure with time, successively caused by the membrane breaking shock wave, the secondary explosion in the tube, and the continuous combustion, and decreases gradually with the propagation distance. Meanwhile, the three pressure peaks are positively correlated with the opening pressure, while the time interval between them goes to contrary. The increase of opening pressure leads to the increase of secondary explosion intensity and reverse flow in the vessel, further accelerates the reaction rate in the vessel, and then shortens the duration of combustion in the vessel until the phenomenon of flame reignition in the vessel disappears.     

煤矿火区快速封闭泄爆门研究

目前煤矿发生火灾事故后,火区封闭时间过长极易引发瓦斯爆炸等次生灾害,且煤矿现有的阻隔爆技术存在许多 不足,针对这些问题,研发一种用于煤矿火区的快速封闭泄爆门。通过对泄爆门的结构设计、封闭与泄爆机制及有益效 果等方面进行阐述,并采用流体力学FLUENT软件计算得出不同数量泄爆窗的泄爆门与监控泄爆门前截面的压力、速度之 间的变化情况。结果表明:6个泄爆窗比2个泄爆窗的封闭时间快1 200 ms,快速封闭时间节省了68.57%。随着泄爆窗的 增多,瓦斯爆炸冲击波压力和传播速度都大幅度降低。当煤矿发生火灾事故封闭火区时,快速封闭泄爆门不仅具有快速 密闭功能,也同时具有泄爆功能,为煤矿安全提供新的隔爆技术。     

泄爆面积比对泄爆门封闭泄爆特性的影响研究*

为研究泄爆面积比对泄爆门泄爆特性的影响,运用FLUENT软件建立煤矿井下1∶1巷道模型,在不同泄爆面积比的工况下对瓦斯爆炸传播规律及泄爆过程进行模拟,分析其变化特征和封闭泄爆效果。结果表明:S0工况条件下,压力和温度衰减后保持在0.29 MPa和565 K;S1~S4工况条件下,S4比S1,S2和S3达到封闭状态时间快780,260,50 ms,封闭时间最大节省70.91%;随着泄爆面积比的增大,封闭火区内的压力的峰值、峰值数量和达到封闭状态时间减小,泄爆能力增强;火焰速度峰值和衰减速率增大;温度的初始峰值、峰值数量和达到稳定状态时间减小,最大峰值反而增大,说明泄爆门对瓦斯爆炸火焰无抑制作用。     

Flame behaviors and pressure characteristics of vented dust explosions at elevated static activation overpressures

Dust explosion venting experiments were performed using a 20-L spherical chamber at elevated static activation overpressures larger than 1 bar. Lycopodium dust samples with mean diameter of 70 μm and electric igniters with 0.5 KJ ignition energy were used in the experiments. Explosion overpressures in the chamber and flame appearances near the vent were recorded simultaneously. The results indicated that the flame appeared as the under-expanded free jet with shock diamonds, when the overpressure in the chamber was larger than the critical pressure during the venting process. The flame appeared as the normal constant-pressure combustion when the pressure venting process finished. Three types of venting processes were concluded in the experiments: no secondary flame and no secondary explosion, secondary flame, secondary explosion. The occurrence of the secondary explosions near the vent was related to the vent diameter and the static activation overpressure. Larger diameters and lower static activation overpressures were beneficial to the occurrence of the secondary explosions. In current experiments, the secondary explosions only occurred at the following combinations of the vent diameter and the static activation overpressure: 40 mm and 1.2 bar, 60 mm and 1.2 bar, 60 mm and 1.8 bar.     

Flameless venting of dust explosion: Testing and modeling

Flameless venting is a sort of dual mitigation technique allowing, in principle, to vent a process vessel inside a building where people are working without transmitting a flame outside the protected vessel. Existing devices are an assembly of a vent panel and a metal filter so that the exploding cloud and the flame front is forced to go through the filter. Within the frame of ATEX Directive, those systems need to be certified. To do so a standard (NF EN 16009) has been issued describing which criteria need to be verified/measured. Among them, the “efficiency” factor as defined earlier for standard vents. This implies that flameless venting systems are basically considered as vents. But is it really so? This question is discussed on the basis of experimental results and some implications on the practical use and certification process are drawn. The practical experience of INERIS in testing such systems is presented in this paper. Schematically, with a flameless vent the pressure is discharged but not the flame so that combustion is proceeding to a much longer extent inside the vessel than with a classical vent so that the physics of the explosion is different. In particular it is shown that besides the problem of the unloading of the confined explosion, there is a highly complicated fluid mechanics problem of a fluid-particle flow passing through a porous media (the flameless device grids arrangement in the filter), which passing surface is progressively reduced. To characterize Flameless venting the problem can be addressed sequentially, considering separately the vent panel and the flameless mesh. A model is proposed to estimate the overall venting efficiency of the flameless vent. However, it does not address the flame quenching issue, which is a different problem of heat exchange between the devices and the evacuated burnt products.     

加气站压缩机间气体爆炸数值模拟研究

加气站压缩机间安全设计时,需要评估内部气体爆炸危害,确定爆炸能量和影响因素。采用CFD技术,建立加气站压缩机间三维模型,模拟不同点火源位置、泄压板不同泄压压力和重量下,压缩机间气体爆炸时的爆炸压力及火焰传播行为。结果表明点火源位置以及泄压参数是影响加气站压缩机间气体爆炸的重要因素;点火源位置距离压缩机间放空位置越近,爆炸压力越小;对于泄压参数,爆炸压力与泄压板开启压力和重量之间均为正比关系。为减缓压缩机间内的气体爆炸危害,需要合理布置点火源位置,选择容重轻、泄压压力小的泄压材料,并同时需要考虑爆炸导致的物体破碎危害以及火焰次生灾害。     

Characteristics of dust explosion venting pressure and flame under high activation pressure

A 20 L spherical explosive device with a venting diameter of 110 mm was used to study the vented pressure and flame propagation characteristics of corn dust explosion with an activation pressure of 0.78–2.1 bar and a dust concentration of 400∼900 g/m³. And the formation and prevention of secondary vented flame are analyzed and discussed. The results show that the maximum reduced explosion overpressure increases with the activation pressure, and the vented flame length and propagation speed increase first and then decrease with time. The pressure and flame venting process models are established, and the region where the secondary flame occurs is predicted. Whether there is pressure accompanying or not in the venting process, the flame venting process is divided into two stages: overpressure venting and normal pressure venting. In the overpressure venting stage, the flame shape gradually changes from under-expanded jet flame to turbulent jet flame. In the normal pressure venting stage, the flame form is a turbulent combustion flame, and a secondary flame occurs under certain conditions. The bleed flames within the test range are divided into three regions and four types according to the shape of the flame and whether there is a secondary flame. The analysis found that when the activation pressure is 0.78 bar and the dust concentration is less than 500 g/m³, there will be no secondary flame. Therefore, to prevent secondary flames, it is necessary to reduce the activation pressure and dust concentration. When the dust concentration is greater than 600 g/m³, the critical dust concentration of the secondary flame gradually increases with the increase of the activation pressure. Therefore, when the dust concentration is not controllable, a higher activation pressure can be selected based on comprehensive consideration of the activation pressure and destruction pressure of the device to prevent the occurrence of the secondary flame.     

Effect of the vent burst pressure on explosion venting of rich methane-air mixtures in a cylindrical vessel

The effect of the vent burst pressure on explosion venting of a rich methane-air mixture was experimentally investigated in a small cylindrical vessel. The experimental results show that Helmholtz oscillation of the internal flame bubble of the methane-air mixture can occur in a vessel with a vent area much smaller than that reported by previous researchers, and the period of Helmholtz oscillation decreases slightly when the vent burst pressure increases. The maximum overpressure in the vessel increases approximately linearly with the increase in the vent burst pressure; however, the pressure peaks induced by Helmholtz oscillation always remain approximately several kilopascals. The external flame reaches its maximum length in a few milliseconds after vent failure and then oscillates in accordance with the pressure oscillation in the vessel. The maximum length of the external flame increases, but its duration time decreases with the increase in the vent burst pressure.     

FA型高炉煤气管道火焰捕器研制

研制满足高炉煤气管道阻火的火焰捕器.内径88 mm、199 mm和305 mm组合爆炸管道模拟实验结果表明,FA型火焰捕器的阻火性能良好,满足高炉煤气管道阻火的技术要求,各项技术性能指标达到了设计要求.     

Effects of vent layout and vent area on dynamic characteristics of premixed methane-air explosion in a tube with two side-vented ducts

To further elucidate the influence mechanism of side vents on the dynamic characteristics of gas explosions in tubes is helpful to design more reasonable vent layouts. In this paper, 9.5% methane-air explosion experiments were conducted in a tube with two side-vented ducts, and the effects of vent layouts and vent areas on the dynamic characteristics of explosion overpressure and flame propagation speed were investigated. The results demonstrate that under the same condition with a single vent area of 100 mm × 100 mm, when only the end vent is open, the maximum explosion overpressure and the maximum flame propagation speed are the highest among the five vent layouts. When the side vents 1 and 2 and the end vent are open, the maximum explosion overpressure is the lowest, and an unusual discovery is that the flame front changes into a hemispherical shape, finger shape, quasi-plane shape, tulip shape and wrinkled structure. When only side vent 1 is open, a unique Helmholtz oscillation occurs, and a new discovery is that there is a consistent oscillation relationship among the overpressure, flame propagation speed and flame structure. Helmholtz oscillation occurs only when a single vent area is 100 mm × 100 mm–60 mm × 60 mm, and the oscillation degree decreases with decreasing vent area. During the vent failure stage, the maximum explosion overpressure is generated, the flame front begins to appear irregular shape, and the flame propagation speed shows a prominent characteristic peak. After the vent failure stage, the driving effect of the end vent on the flame is higher than that of the side vent on the flame. Furthermore, the correlation equations of the mathematical relationships among the maximum explosion overpressure P_red, the static activation pressure P_stat and the vent coefficient K_v under four vent layouts are established, respectively.