Influence of ageing of residues on the availability of herbicides for leaching

Losses by leaching of chlorotoluron, isoproturon and triasulfuron from small intact columns of a structured clay loam and an unstructured sandy loam soil were measured in five separate field experiments. In general, losses of all three herbicides were greater from the clay loam than from the sandy loam soil and the order between herbicides was always triasulfuron > isoproturon > chlorotoluron. Differences between experiments were also consistent for every soil/herbicide combination. There was no relationship between total loss and either total rainfall or cumulative leachate volume. When weighting factors were applied to the rainfall data to make early rainfall more important than later rainfall, there were significant positive relationships between cumulative weighted rainfall and total losses. Also, there were significant negative correlations between total losses and the delay to accumulation of 25 mm rainfall (equivalent to one pore volume of available water) in the different experiments. In laboratory incubations, there was a more rapid decline in aqueous (0.01 M calcium chloride) extractable residues than in total solvent extractable residues indicating increasing sorption with residence time. However, the rate of change in water extractable residues could not completely explain the decrease in leachability with ageing of residues in the field. Short-term sorption studies with aggregates of the two soils indicated slower sorption by those of the clay loam than by those of the sandy loam suggesting that diffusion into and out of aggregates may affect availability for leaching in the more structured soil. Small scale leaching studies with aggregates of the soils also demonstrated reductions in availability for leaching as residence time in soil was increased, which could not be explained by degradation. These results therefore indicate that time-dependent sorption processes are important in controlling pesticide movement in soils, although the data do not give a mechanistic explanation of the changes in leaching with ageing of residues.     

Effects of temperature and water content on degradation of isoproturon in three soil profiles

The phenylurea herbicide isoproturon, 3-(4-isopropylphenyl)-1,1-dimethylurea (IPU), is widely used to control pre- and post-emergence of grass and broad-leaved weeds in cereal crops. Its degradation in soils is a key process for assessing its leaching risk to groundwater resources. The degradation properties of various samples from surface and subsurface soil (down to 1m depth) of a heterogeneous agricultural field were studied using (14)C-IPU. Laboratory incubations were carried out at 22 and 10 degrees C and at water contents 90% and 50% of the estimated water holding capacity (eWHC) corresponding to water potentials between -56 kPa and -660 MPa. Degradation was found to be more sensitive to water content variations than to temperature variations in the ranges that we used. For surface layers, at 10 and 22 degrees C, the degradation half-life increased by a factor 10 and 15, respectively, when water content decreased from 90% to 50% eWHC. Under optimal degradation conditions (i.e. 22 degrees C and 90% eWHC), 3-(4-isopropylphenyl)-1-methylurea (MDIPU) was the main metabolite in surface samples. At subsurface depths, IPU half-lives were larger than 100 d, IPU was the main compound after 92 d of incubation and the main metabolite was an unidentified polar metabolite. These results suggest a metabolic pathway involving hydroxylations for subsurface materials. IPU degradation was largely affected by water availability in both surface and subsurface horizons. Clay content seemed to play a major role in degradation processes in subsurface soil by determining through sorption IPU availability in soil solution and/or by limiting water availability for microorganisms.     

Degradation of herbicides in two sandy aquifers under different redox conditions.

We examined the potential for complete degradation (mineralisation) of the four [ring-U-14C]herbicides mecoprop, isoproturon, atrazine, and metsulphuron-methyl in two sandy aquifers representing aerobic, denitrifying, sulphate-reducing, and methanogenic conditions. Slurries with sediment and groundwater were set-up aerobically or anaerobically in the presence of the electron-acceptor prevailing at the sampling site, amended with 25 microg l(-1) herbicide, and incubated at 10 degrees C. Considerable mineralisation was only observed in sediment from the plough layer incubated aerobically. Here, 30% of 14C-mecoprop was recovered as 14CO2 after 15 days and 15% of isoproturon was recovered as 14CO2 after 267 days. Only 7% of mecoprop was recovered as 14CO2 after 313 days in sediment from the aquifer below sampled at 1.95-3.00 mbs (m below the surface). In denitrifying and methanogenic slurries, 3% of 14C added as mecoprop was recovered as 14CO2. Isoproturon was not mineralised except in the aerobic plough layer, and atrazine and metsulphuron-methyl were not mineralised under any of the conditions applied.     

Mobility of isoproturon from an alginate-bentonite controlled release formulation in layered soil

The mobility of isoproturon [3-(4-isopropylphenyl)-1,1-dimethylurea] from an alginate-based controlled release (CR) formulation was investigated by using soil columns. A layered bed system simulating the typical arrangement under a plastic greenhouse, which is composed of sand, peat, amended soil and native soil was used. The CR formulation was based on sodium alginate (1.87%), isoproturon (1.19%), natural bentonite (3.28%), and water (93.66%), and was compared to technical grade isoproturon. The use of the alginate-bentonite CR formulation produced less vertical mobility of the active ingredient as compared to the technical product. There was no presence of herbicide in the leachate when the alginate-bentonite CR formulation was used. However, 0.90% of isoproturon appeared when the treatment was carried out with technical grade material. Isoproturon mobility was modelled using the programme CMLS, which showed the peat layer to retard pesticide leaching. Analysis of the soil columns showed the highest isoproturon concentration in the peat layer.     

Runoff and leaching of atrazine and alachlor on a sandy soil as affected by application in sprinkler irrigation

Rainfall simulation was used with small packed boxes of soil to compare runoff of herbicides applied by conventional spray and injection into sprinkler-irrigation (chemigation), under severe rainfall conditions. It was hypothesized that the larger water volumes used in chemigation would leach some of the chemicals out of the soil surface rainfall interaction zone, and thus reduce the amounts of herbicides available for runoff. A 47-mm rain falling in a 2-hour event 24 hours after application of alachlor (2-chloro-N-(2,6-diethylphenyl)-N-(methoxymethyl)-acetamide) and atrazine (6-chloro-N-ethyl-N'-(1-methylethyl)-1,3,5-triazine-2, 4-diamine) was simulated. The design of the boxes allowed a measurement of pesticide concentrations in splash water throughout the rainfall event. Initial atrazine concentrations exceeding its' solubility were observed. When the herbicides were applied in 64,000 L/ha of water (simulating chemigation in 6.4 mm irrigation water) to the surface of a Tifton loamy sand, subsequent herbicide losses in runoff water were decreased by 90% for atrazine and 91% for alachlor, as compared to losses from applications in typical carrier water volumes of 187 L/ha. However, this difference was not due to an herbicide leaching effect but to a 96% decrease in the amount of runoff from the chemigated plots. Only 0.3 mm of runoff occurred from the chemigated boxes while 7.4 mm runoff occurred from the conventionally-treated boxes, even though antecedent moisture was higher in the former. Two possible explanations for this unexpected result are (a) increased aggregate stability in the more moist condition, leading to less surface sealing during subsequent rainfall, or (b) a hydrophobic effect in the drier boxes. In the majority of these pans herbicide loss was much less in runoff than in leachate water. Thus, in this soil, application of these herbicides by chemigation would decrease their potential for pollution only in situations where runoff is a greater potential threat than leaching.     

Effect of charcoal amendment on adsorption, leaching and degradation of isoproturon in soils

The effects of charcoal amendment on adsorption, leaching and degradation of the herbicide isoproturon in soils were studied under laboratory conditions. The adsorption data all fitted well with the Freundlich empirical equation. It was found that the adsorption of isoproturon in soils increased with the rate of charcoal amended (correlation coefficient r=0.957**, P<0.01). The amount of isoproturon in leachate decreased with the increase of the amount of charcoal addition to soil column, while the retention of isoproturon in soils increased with an increase in the charcoal content of soil samples. Biodegradation was still the most significant mechanism for isoproturon dissipation from soil. Charcoal amendment greatly reduced the biodegradation of isoproturon in soils. The half-lives of isoproturon degradation (DT(50)) in soils greatly extended when the rate of added charcoal increased from 0 to 50 g kg(-1) (for Paddy soil, DT(50) values increased from 54.6 to 71.4 days; for Alfisol, DT(50) from 16.0 to 136 days; and for Vertisol, DT(50) from 15.2 to 107 days). The degradation rate of isoproturon in soils was significantly negatively correlated with the amount of added charcoal. This research suggests that charcoal amendment may be an effective management practice for reducing pesticide leaching and enhancing its persistence in soils.     

Determination of solid-liquid partition coefficients (Kd) for the herbicides isoproturon and trifluralin in five UK agricultural soils

Isoproturon and trifluralin are herbicides of contrasting chemical characters and modes of action. Standard batch sorption procedures were carried out to investigate the individual sorption behaviour of 14C-isoproturon and 14C-trifluralin in five agricultural soils (1.8-4.2% OC), and the soil solid-liquid partition coefficients (Kd values) were determined. Trifluralin exhibited strong partitioning to the soil solid phase (Kd range 106-294) and low desorption potential, thus should not pose a threat to sensitive waters via leaching, although particle erosion and preferential flow pathways may facilitate transport. For isoproturon, soil adsorption was low (Kd range 1.96-5.75) and desorption was high, suggesting a high leaching potential, consistent with isoproturon being the most frequently found pesticide in UK surface waters. Soil partitioning was directly related to soil organic carbon (OC) content. Accumulation isotherms were modelled using a dual-phase adsorption model to estimate adsorption and desorption rate coefficients. Associations between herbicides and soil humic substances were also shown using gel filtration chromatography.     

Retention behavior of hydrophobic organic chemicals as a function of temperature in soil leaching column chromatography

To study the transport mechanism of hydrophobic organic chemicals (HOCs) and the energy change in soil/solvent system, a soil leaching column chromatographic (SLCC) experiment at an environmental temperature range of 20-40 degrees C was carried out, which utilized a reference soil (SP 14696) packed column and a methanol-water (1:4 by volume ratio) eluent. The transport process quickens with the increase of column temperature. The ratio of retention factors at 30 and 40 degrees C (k'30/k'40) ranged from 1.08 to 1.36. The lower enthalpy change of the solute transfer in SLCC (from eluent to soil) than in conventional reversed-phase liquid chromatography (e.g., from eluent to C18) is consistent with the hypothesis that HOCs were dominantly and physically partitioned between solvent and soil. The results were also verified by the linear solvation energy relationships analysis. The chief factor controlling the retention was found to be the solute solvophobic partition, and the second important factor was the solute hydrogen-bond basicity, while the least important factors were the solute polarizability-dipolarity and hydrogen-bond acidity. With the increase of temperature, the contributions of the solute solvophobic partition and hydrogen-bond basicity gradually decrease, and the latter decreases faster than the former.     

Sorption behavior of metolachlor, isoproturon, and terbuthylazine in soils

The sorption-desorption of metolachlor [2-chloro-N-(ethyl-6-methyl phenyl)-N-(2-methoxy-1-methyl ethyl) acetamide], isoproturon [3-(4-isopropyl phenyl)-1,1-dimethyl urea] and terbuthylazine [N6-tert butyl-6-chloro-N4-ethyl-1,3,5-triazine-2,4-diamine] herbicides was studied in two German soils at 1:10 soil to water ratio by batch method. Equilibrium of herbicides between soil and water (0.01 M CaCl2) was attained in 2 h. Sorption data fitted very well to Freundlich equation, represented by very high correlation coefficient (r2 > 0.934). Comparison of Freundlich K values indicated that sorption of all the three herbicides was most pronounced in soil having higher organic carbon content. Koc values were as expected nearly identical for each herbicide in the two soils. The Freundlich constant (1/n) was about 1 for metolachlor and less than 1 for terbuthylazine and isoproturon indicating a L-type of sorption isotherms. Desorption of all the three herbicides showed hysteresis. Nearly equal amounts of metolachlor, isoproturon and terbuthylazine were desorbed from both soils. There was a good correlation between Koc and solubility.     

Influence of a heavy rainfall event on the leaching of [14C]isoproturon and its degradation products in outdoor lysimeters

In four different agricultural soils the long-term leaching behaviour of [14C]isoproturon was studied in outdoor lysimeters (2 m length, 1 m2 surface area). The herbicide was applied in spring 1997 and spring 2001. At the end of the first 4-year-investigation period between 0.13% and 0.31% of the applied radioactivity was leached. Isoproturon or known metabolites could not be detected in the leachate. However, shortly after the second application isoproturon and its degradation products 2-hydroxy-isoproturon and monodemethyl-isoproturon were leached via preferential flow in one of the lysimeters (Mollic gleysol) in concentrations of 4.5 microg L-1, 3.1 microg L-1 and 0.9 microg L-1, respectively, thus considerably exceeding the EU threshold limit of 0.1 microg L-1 for ground and drinking water. The results indicate that in soils where mass flow transfer dominates, leaching of isoproturon to groundwater is of low probability whereas in highly structured soils which have the tendency to form macropores, isoproturon can be transported via preferential flow to the groundwater.     

Runoff and leaching of atrazine and alachlor on a sandy soil as affected by application in sprinkler irrigation

Abstract

Rainfall simulation was used with small packed boxes of soil to compare runoff of herbicides applied by conventional spray and injection into sprinkler‐irrigation (chemigation), under severe rainfall conditions. It was hypothesized that the larger water volumes used in chemigation would leach some of the chemicals out of the soil surface rainfall interaction zone, and thus reduce the amounts of herbicides available for runoff. A 47‐mm rain falling in a 2‐hour event 24 hours after application of alachlor (2‐chloro‐N‐(2,6‐diethylphenyl)‐N‐(methoxymethyl)‐acetamide) and atrazine (6‐chloro‐N‐ethyl‐N‐(1‐methylethyl)‐1,3,5‐triazine‐2,4‐diamine) was simulated. The design of the boxes allowed a measurement of pesticide concentrations in splash water throughout the rainfall event. Initial atrazine concentrations exceeding its’ solubility were observed. When the herbicides were applied in 64000 L/ha of water (simulating chemigation in 6.4 mm irrigation water) to the surface of a Tifton loamy sand, subsequent herbicide losses in runoff water were decreased by 90% for atrazine and 91% for alachlor, as compared to losses from applications in typical carrier water volumes of 187 L/ha. However, this difference was not due to an herbicide leaching effect but to a 96% decrease in the amount of runoff from the chemigated plots. Only 0.3 mm of runoff occurred from the chemigated boxes while 7.4 mm runoff occurred from the conventionally‐treated boxes, even though antecedent moisture was higher in the former. Two possible explanations for this unexpected result are (a) increased aggregate stability in the more moist condition, leading to less surface sealing during subsequent rainfall, or (b) a hydrophobic effect in the drier boxes. In the majority of these pans herbicide loss was much less in runoff than in leachate water. Thus, in this soil, application of these herbicides by chemigation would decrease their potential for pollution only in situations where runoff is a greater potential threat than leaching.     

Spatial variability in the degradation rate of isoproturon in soil

Thirty samples of soil were taken at 50-m intersections on a grid pattern over an area of 250 x 200 m within a single field with nominally uniform soil characteristics. Incubations of isoproturon (3-(4-isopropylphenyl)-1,1-dimethylurea) under standard conditions (15 degrees C; -33 kPa soil water potential) indicated considerable variation in degradation rate of the herbicide, with the time to 50% loss (DT50) varying from 6.5 to 30 days. The kinetics of degradation also varied between the sub-samples of soil. In many of them, there was an exponential decline in isoproturon residues; in others, exponential loss was followed by more rapid rates of decline; in a few soil samples, rapid rates of loss began shortly after the start of the incubations. In more detailed studies with soils from a smaller number of sub-sites (20), measurements were again made of isoproturon degradation rate, and the soils were analysed for organic matter content, pH, and nutrient status (N, P, K). Measurements were also made of isoproturon adsorption by the soils and of soil microbial biomass. Patterns of microbial metabolism were assessed using 95 substrates in Biolog GN plates. Soils showing rapid biodegradation were generally of higher pH and contained more available potassium than those showing slower degradation rates. They also had a larger microbial biomass and greater microbial metabolic diversity as determined by substrate utilisation on Biolog GN plates. The implications of the results for the efficacy and environmental behaviour of isoproturon are discussed.     

Dolomite phosphate rock (DPR) application in acidic sandy soil in reducing leaching of phosphorus and heavy metals—a column leaching study

A column leaching study was designed to investigate the leaching potential of phosphorus (P) and heavy metals from acidic sandy soils applied with dolomite phosphate rock (DPR) fertilizers containing varying amounts of DPR material and N-Viro soils. DPR fertilizers were made from DPR materials mixing with N-Viro soils at the ratios of 30, 40, 50, 60, and 70 %, and applied in acidic sandy soils at the level of 100 mg available P per kilogram soil. A control and a soluble P chemical fertilizer were also included. The amended soils were incubated at room temperature with 70 % field water holding capacity for 21 days before packed into a soil column and subjected to leaching. Seven leaching events were conducted at days 1, 3, 7, 14, 28, 56, and 70, respectively, and 258.9 mL of deionized water was applied at each leaching events. The leachate was collected for the analyses of pH, electrical conductivity (EC), dissolved organic carbon (DOC), major elements, and heavy metals. DPR fertilizer application resulted in elevations up to 1 unit in pH, 7–10 times in EC, and 20–40 times in K and Ca concentrations, but 3–10 times reduction in P concentration in the leachate as compared with the chemical fertilizer or the control. After seven leaching events, DPR fertilizers with adequate DPR materials significantly reduced cumulative leaching losses of Fe, P, Mn, Cu, and Zn by 20, 55, 3.7, 2.7, and 2.5 times than chemical fertilizer or control. Even though higher cumulative losses of Pb, Co, and Ni were observed after DPR fertilizer application, the loss of Pb, Co, and Ni in leachate was <0.10 mg (in total 1,812 mL leachate). Significant correlations of pH (negative) and DOC (positive) with Cu, Pb, and Zn (P?<?0.01) in leachate were observed. The results indicated that DPR fertilizers had a great advantage over the soluble chemical fertilizer in reducing P loss from the acidic sandy soil with minimal likelihood of heavy metal risk to the water environment. pH elevation and high dissolved organic carbon concentration in soils after DPR fertilizer application are two influential factors.     

Assessment of metolachlor and diuron leaching in a tropical soil using undisturbed soil columns under laboratory conditions

In the present study, diuron [3-(3,4-dichlorophenyl)-1,1-dimethylurea] and metolachlor [2-chloro-N-(2-ethyl-6-methylphenyl)-N-(2-metoxi-1-methylethyl)acetamide] leaching was studied in undisturbed soil columns collected in a cotton crop area in Mato Grosso State, Brazil. The pesticides were applied to the soil surface in dosages similar to those used in a cotton plantation. To assess the leaching process, soil columns were submitted to simulated rain under laboratory conditions at 25 ± 3°C, in the absence of wind and direct solar radiation. During the rain simulations, leachate solutions were collected and herbicide concentrations were determined. At the end of the experiment, the soil columns were cut into 10 cm sections to determine the remaining herbicide concentrations through the soil profile. Metolachlor was detected in all soil sections, and approximately 4% of the applied mass was leached. Diuron was detected only in the upper two soil sections and was not detected in the leachate. A linear correlation (r > 0.94) between the metolachlor soil concentrations and the organic contents of the soil sections was observed. Mass balance suggests that around 56% of diuron and 40% of metolachlor were degraded during the experiments. Measurements of the water table depth in the area where the samples were collected showed that it varied from 2 to 6 m and is therefore vulnerable to contamination by the studied herbicides, particularly metolachlor, which demonstrated a higher leaching potential.     

Fate of anilide and aniline herbicides in plant-materials-amended soils

The fate of herbicides trifluralin, pendimethalin, alachlor and metolachlor in paddy field soils amended with plant materials was investigated. The plant materials were purple sesbania, vegetable soybean and rice straw. The investigation was performed at two temperatures (25 and 40 degrees C) and two soil water moistures (60 and 90% water-holding capacity). The results showed linear and Freudlich equations described the adsorption of amide compound to soil. Adsorption coefficient (K(d)) fit to linear equation were in general greater in plant material-amended soils than in non-amended soil, especially in soil amending with rice straw. Increasing temperature and soil water moisture content shortened the half-lives of compounds in various treated soils. The movement of compounds in the soil columns showed the maximum distribution of aniline type compound, trifluralin and pendimethalin, appeared at the upper top of 0 to 5 and 0 to 10 cm of soil column, respectively, and of anilide type, alachlor and metolachlor, were distributed at 0 to 25 cm of the soil column. The mobility of chemicals in the different treated soils was simulated by the behavior assessment model (BAM). There was no significant difference among different plant material incubated soils on dissipation and mobility of compounds in soils.     

Adsorption-desorption,persistence, and leaching behavior of dithiopyr in an alluvial soil of India

Investigations were undertaken to determine the adsorption-desorption, persistence and leaching of dithiopyr (S,S'-dimethyl 2-difluoromethyl-4-isobutyl-6-trifluoromethyl pyridine-3,5-dicarbothioate) in an alluvial soil under laboratory condition. The adsorption-desorption studies were carried out using batch equilibration technique. The mass balance studies showed that 83-97% of the pesticide was recovered during adsorption-desorption studies. The results revealed strong adsorption of dithiopyr in alluvial soil with Kd values ranging from 3.97-5.78 and Freundlich capacity factor (KF) value of 2.41. The strong adsorption was evident from the hysteresis effect observed during desorption. The hysteresis coefficients ranged from 0.17-0.40. The persistence studies were carried out at two concentrations (1.0 and 10.0 microg g(-1) level) under field capacity moisture and submerged condition by incubating the treated soil at 25 +/- 1 degrees C. In general, dithiopyr persisted beyond 90 days with half-life varying from 11.5-12.9 days under different conditions. The rate of application and moisture regimes had no overall effect on the persistence. The leaching studies carried out in packed column under saturated flow condition revealed that dithiopyr was highly immobile in alluvial soil. Only small amounts (0.02-0.04%) were recovered from leachate whereas major portion (99.9%) remained in top layer of the soil column. The data suggest that strong adsorption of dithiopyr will cause a greater persistence problem in the soil. However, the chances of its movement to ground water will be negligible due to its immobility.     

Leaching of mecoprop and dichlorprop in calcareous soil. Effect of the exogen organic matter addition in this process.

Leaching studies of mecorprop (R,S)-2-(4-chloro-2-methylphenoxy)propanoic acid, and dichlorprop, (R,S)-2-(4-chloro-2,4-dichlorophenoxy) propanoic acid, under saturated conditions were conducted in unamended and amended soil columns. The purpose of the study was to investigate the leaching of these herbicides in three type of soils and the exogen organic matter effect on this process. The leaching patterns could be related to variation in the soil texture and diffusion processes of the herbicides into micropores within the walls of conducting pore. The leaching rate in the amended soil columns decreased with the addition of organic matter. The breakthrough curves (BTC) of these herbicides in the leachates of the amended soil columns were wider and more diffused than the BTC obtained for the corresponding unamended soil. The theoretical BTC overestimated the pore volume required for the displacement of these pesticides from the soil column. This may be due to the differences in the adsorption process between the bacth and soil columns methods.     

Leaching of mecoprop and dichlorprop in calcareous soil. Effect of the exogen organic matter addition in this process

Abstract

Leaching studies of mecorprop (R,S)‐2‐(4‐chloro‐2‐methylphenoxy)propanoic acid, and dichlorprop, (R,S)‐2‐(4‐chloro‐2,4‐dichlorophenoxy) propanoic acid, under saturated conditions were conducted in unamended and amended soil columns. The purpose of the study was to investigate the leaching of these herbicides in three type of soils and the exogen organic matter effect on this process. The leaching patterns could be related to variation in the soil texture and diffusion processes of the herbicides into micropores within the walls of conducting pore. The leaching rate in the amended soil columns decreased with the addition of organic matter. The breakthrough curves (BTC) of these herbicides in the leachates of the amended soil columns were wider and more diffused than the BTC obtained for the corresponding unamended soil. The theoretical BTC overestimated the pore volume required for the displacement of these pesticides from the soil column. This may be due to the differences in the adsorption process between the bacth and soil columns methods     

Effect of concentration,moisture and soil type on the dissipation of flufenacet from soil

Effect of concentration, moisture and soil type on dissipation of flufenacet from soil has been studied under laboratory condition. The treated soil samples (1 and 10 microg/g levels) were incubated at 25+/-1 degrees C. The effect of moisture was studied by maintaining the treated soil samples (10 microg/g level) at field capacity and submerged condition. In general, flufenacet persisted for 60-90 days at lower and beyond 90 days at high rate. The dissipation of flufenacet from soil followed first order kinetics with half-life (DT50) values ranging from 10 to 31 days. The dissipation of flufenacet was faster at low rate than high rate of application. The slow dissipation at high rate could be attributed to inhibition of microbial activity at high rate. There was little overall difference in rate of dissipation in Ranchi and Nagpur soil maintained at field capacity and submerged condition moisture regimes. In Delhi soil net dissipation was faster under field capacity moisture than submerged condition. Soil types greatly influenced the dissipation of flufenacet. Dissipation was fastest in Delhi soil (DT50 10.1-22.3 days) followed by Ranchi soil (DT50 10.5-24.1 days) and least in Nagpur soil (DT50 29.2-31.0 days). The difference in dissipation could be attributed to the magnitude of adsorption and desorption of flufenacet in these soils.     

Degradation of [14C]isofenphos in soil in the laboratory under different soil pH's, temperatures, and moistures

The effects of three soil pH's, three soil temperatures, and three soil moistures on [14C]isofenphos degradation were investigated. All three factors interacted strongly and significantly affected the persistence of isofenphos as well as the formation of the degradation products (p less than 1%). Isofenphos degradation was greatest at the higher temperatures 35 degrees C greater than 25 degrees C greater than 15 degrees C (except under alkaline pH's), medium moisture 25% greater than 30% greater than 15%, and in both alkaline (pH = 8) and acidic soils (pH = 6) compared with neutral soil (pH = 7). Isofenphos oxon formation was greatest at higher temperatures 35 degrees C compared with 25 degrees C and 15 degrees C, in acidic soil greater than neutral soil greater than alkaline soil, and under high moisture (30%) compared with the 15% and 22.5% moistures. The formation of soil-bound residues was greatest at higher temperatures 35 degrees C greater than 25 degrees C greater than 15 degrees C, higher moisture 30% compared with 15% and 22.5%, and in alkaline soil compared with neutral and acidic soils.