Heavy metal concentrations in water, suspended matter, and sediment from Gökova Bay, Turkey

The contents of heavy metals (Fe, Mn, Pb, Cu, Cd, and Hg) dissolved in water and suspended solids of Gökova Bay—partly and fully sampled in 2005 and 2006, respectively—are quite higher than the average values encountered in uncontaminated sea water. The high concentrations are associated with terrestrial inputs from the mining zones and anthropogenic (domestic + industrial) sources. Moreover, the distribution of Fe and Cu is affected by primary production because these elements function as nutrients in biological activities. The Cr, Ni, and Fe concentrations of surface sediments are above the shale average. The Cr and Ni contents of surface sediments representative of river mouths strongly correlate with total phosphorus contents. In a sulfide-poor environment, Pb and Cu were concentrated at a higher ratio in surface sediments than Cd, probably due to higher stabilities of their surface complexes with amorphous iron oxides and clay minerals existing as major components in the sediments. The exceptional enrichment of Zn may be attributed to double oxide formation with amorphous iron oxides in sediments. The high metal values are most probably caused by terrestrial inputs from anthropogenic sources and the mining zones at the southeast part of the bay. The Al, Mn, Pb, Cu, Zn, and Hg contents are below the shale average. The low values have possibly originated from the coarse-grained sandy sediments having a low affinity for metals. There are no distinct differences in the metal distributions in water and suspended matter between the years 2005 and 2006 in the bay, probably due to low sedimentation rates.     

Cumulative influences of a small city and former mining activities on the sediment quality of a subtropical estuarine protected area

This study aimed to evaluate the sediment quality in the estuarine protected area known as Cananéia-Iguape-Peruíbe (CIP-PA), located on the southeastern coast of Brazil. The study was designed considering possible negative effects induced by the city of Cananéia on the sediment quality of surrounding areas. This evaluation was performed using chemical and ecotoxicological analyses. Sediments were predominantly sandy, with low CaCO₃ contents. Amounts of organic matter varied, but higher contents occurred closer to the city, as well as did Fe and Total Recoverable Oils and Greases (TROGs) concentrations. Contamination by Cd and Cu was revealed in some samples, while concentrations of Zn were considered low. Chronic toxicity was detected in all tested sediments and acute toxicity occurred only in sediments collected near the city. The principal component analysis (PCA) revealed an association among Cd, Cu, Fe, TROG, fines, organic matter, CaCO₃, and chronic toxicity, whereas acute toxicity was found to be associated with Zn and mud. However, because Zn levels were low, acute toxicity was likely due to a contaminant that was not measured. Results show that there is a broad area within the CIP-PA that is under the influence of mining activities (chronic toxicity, moderate contamination by metals), whereas poorer conditions occur closer to Cananéia (acute toxicity); thus, the urban area seems to constitute a relevant source of contaminants for the estuarine complex. These results show that contamination is already capable of producing risks for the local aquatic biota, which suggests that the CIP-PA effectiveness in protecting estuarine biota may be threatened.     

Metal and hydrocarbon behavior in sediments from Brazilian shallow waters drilling activities using nonaqueous drilling fluids (NAFs)

The impact of drilling oil activities in the Brazilian Bonito Field/Campos Basin (Rio de Janeiro) shell drilling (300 m) using nonaqueous fluids (NAFs) was investigated with respect to Al, Fe, Mn, Ba, Co, Pb, Cu, As, Hg, Cr, Ni, Zn, Cd, V, and aliphatic and polynuclear aromatic hydrocarbons concentrations in the sediment. Sampling took place in three different times during approximately 33 months. For the metals Al, As, Co, Cr, Cu, Cd, Fe, Ni, Mn, V, and Zn, no significant variation was observed after drilling activities in most of the stations. However, an increase was found in Ba concentration—due to the drilling activity—without return to the levels found 22 months after drilling. High Ba contents was already detected prior to well drilling, probably due to drilling activities in other wells nearby. Hydrocarbon contents also suggest previous anthropogenic activities. Aliphatic hydrocarbon contents were in the range usually reported in other drilling sites. The same behavior was observed in the case of polyaromatic hydrocarbons. Nevertheless, the n-alkane concentration increased sharply after drilling, returning almost to predrilling levels 22 months after drilling activities.     

Elemental analysis of aerosols in Tehran’s atmosphere using PIXE and identification of pollution sources

In this study, the proton-induced X-ray emission (PIXE) technique has been applied to measure the elemental composition and concentrations of particulate matter of 220 samples of aerosols in Tehran’s atmosphere within a 450-day time interval starting from March 2009 and ending in June 2010, covering all four seasons. PIXE analysis shows the samples are comprised of various elements including Al, Si, S, Cl, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, Br, Rb, Sr, and Pb. Also, to obtain more information about the sources of pollution and to identify the major sources of urban particulate matter, principal component analysis (PCA) was used. Furthermore, micro-PIXE was performed to study individual aerosols in some samples. Results revealed that the concentration of elements originating from vehicle emissions increases three times in winter; whereas the concentration of elements with soil origin remains constant. Based on wind rose maps, it is inferred that the high concentrations of the elements Al, Si, K, Ca, Ti, Mn, and Fe are associated with natural dust brought by winds into Tehran from the west.     

Fractionation of eleven elements by chemical bonding from airborne particulate matter collected in an industrial city in Argentina

A four-step chemical sequential extraction procedure was used to evaluate the distribution of Al, As, Cr, Cu, Fe, Mn, Ni, Pb, Ti, V and Zn in airborne particulate matter collected on glass fibre filters using a high-volume sampler. Two sets of samples were collected in 2001 (winter and summer campaigns) in representative zones of an industrial city of Argentina. The leaching scheme was applied to PM-10 particles and consisted in extracting the elements in four fractions, namely soluble and exchangeable elements; carbonates, oxides and reducible elements; bound to organic matter and sulfidic metals; and residual elements. Metals and metalloids at microg g(-1) level were determined in each fraction by inductively coupled plasma optical emission spectrometry (ICP OES). Analyte concentration varied from 14 microg g(-1) (equivalent to 1.0 ng m(-3)) for As to 11.8 mg g(-1) (equivalent to 2,089 ng m(-3)) for Al. Seven elements, namely Al, Cr, Fe, Mn, Pb, Ti and Zn showed similar distributions in both seasons while As was distributed in a significantly different manner in each season. The results exhibited low As contents in the first and second fractions that could be associated with routine coal combustion and a high content in the third and fourth fractions of the summer samples that could be linked to the use of pesticides. Aluminium, As, Cu, Mn, Ni, Ti, V and Zn were found in different percentages in the more bioavailable aqueous fraction with As, Mn, V and Zn exhibiting solubilities greater than 1% while Cr and Pb being insoluble. The content of Al, Cr, Cu, Fe, Ni, Pb, and Zn in the residual fraction was, in average, higher than 50%. A comparative assessment of the use of the underlying information available from fractionation studies compared to that obtained from total element content was done for Fe and Mn. It showed that the results obtained using chemical sequential extraction procedures allowed further discrimination of the potential air pollution sources.     

Trace elements in muscle of three fish species from Todos os Santos Bay,Bahia State,Brazil

In this study, an analysis was performed on the concentrations of the trace elements Al, As, Ba, Cd, Co, Cr, Cu, Fe, Mn, Ni, Pb, V, and Zn in muscle of two carnivorous and one planktivorous fish species collected at Todos os Santos Bay (BTS). The accumulation order of the trace elements in Lutjanus analis was Al >Zn >Fe >Cr >Ba >Ni. In Cetengraulis edentulus, the order was Al >Fe >Zn >Cr >Ni >Mn >As. In the species Diapterus rhombeus, the order was Al >Fe >Zn >Cr >Ni >Mn >Cd. To determine the risk related to the consumption of fish, toxicity guidelines were used as standard references. It was observed that the species C. edentulus contained concentrations of As exceeding WHO limits, but these concentrations were acceptable according to the Agência Nacional de Vigilância Sanitária (ANVISA) guidelines. Cd levels were found only in D. rhombeus and in low concentrations according to the determinations of WHO and ANVISA. Pb levels were not detected in any of the three fish species. The analyzed elements did not differ statistically according to the species and feeding habits. The results point to possible risks of human contamination by As related to the consumption of the fish species C. edentulus from the BTS.     

Studies on heavy metals in the ground waters of the city of Aligarh U.P. (India)

A study was conducted to determine the levels of heavy metals Cd, Cr, Cu, Fe, Mn, Ni, Pb, and Zn along with physico-chemical parameters in ground waters of Aligarh city, U.P. (India). Twenty seven samples of hand pump water and twenty three samples of municipal water supply were collected from different localities of the Aligarh city, five times during the period of two months at intervals of 12 days. The samples were analysed for physico-chemical characteristics (pH, electrical conductivity, chlorides, sulphates, total hardness, total alkalinity, nitrate-nitrogen, fluoride, calcium and magnesium) and heavy metal contents. The concentrations of heavy metals in the hand pump water samples were found in the ranges of Cd (ND-5.00); Cr (ND-30.00); Cu (ND-82.50); Fe (16.80–460.00); Mn (ND-425.00); Ni (ND-25.00); Pb (ND-25.00) and Zn (28.60–775.00) g l^–1. The heavy metal concentrations in the municipal water supply samples were found to be Cd (ND-5.00); Cr (ND-25.00); Cu (ND-37.50); Fe (8.00–37.50); Mn (ND-320.00); Ni (ND-25.00); Pb (ND-25.00) and Zn (2.00–271.87) g l^–1.It appears from the results of these studies the concentrations of Cd, Cr, Cu, Ni, Pb, and Zn in the ground waters of the Aligarh City were found to be lower than the prescribed limits of World Health Organisation (1984), whereas the values of Fe and Mn were found above the prescribed limits in some localities. The chloride total hardness and nitrate-nitrogen were comparatively higher in the hand pump water than the municipal supply water. The reason of higher values of these parameters may be ascribed to the surface disposal of sewage wastes, wastes from metal processing industries and other house hold refuses.     

Morphological deformities of benthic foraminifera in response to nearshore pollution of the Red Sea,Egypt

The Red Sea encompasses a wide range of tropical marine habitats that are stressed due to anthropogenic activities. The main anthropogenic activities are hydrocarbon exploration and important trading harbors. This work aims to assess the influence of the Red Sea coastal heavy metal contamination on the marine meiofauna along three sites (Ras Gharib, Safaga, and Quseir). Eight heavy metal (Cu, Cd, Zn, Pb, Cr, Co, Ni, and Mn) contents are considered in four benthic foraminiferal species (Elphidium striatopunctatum, Amphistegina lobifera, Amphisorus hemprichii, and Ammonia beccarii). Quseir Harbor showed the highest level of pollution followed by Safaga and Ras Gharib sites. The analyzed benthic foraminiferal tests displayed noteworthy high concentrations of Cd, Zn, and Pb in Quseir Harbor which could be attributed to the anthropogenic activities in the nearshore areas. Some foraminiferal tests exhibited abnormalities in their apertures, coiling, and shape of chambers. A comparison between normal and deformed foraminiferal tests revealed that the deformed ones are highly contaminated with elevated heavy metal contents such as Fe, Mn, Ni, and Cd. Statistics in addition to geo-accumulation and pollution load indices reveal a whistling alarm for the Quseir harbor. The present data are necessary to improve conservation and management of the Red Sea ecosystem in the near future.     

Baseline values for metals in soils on Fildes Peninsula, King George Island, Antarctica: the extent of anthropogenic pollution

Metal contents (Al, Ca, Cd, Cr, Cu, Fe, Hg, Mg, Mn, Ni, Pb, Ti, and Zn) have been measured in 30 surface soils on Fildes Peninsula, King George Island, Antarctica, yielding values (in milligrams kilogram(-1)) of 41.57-80.65 (Zn), 2.76-60.52 (Pb), 0.04-0.34 (Cd), 7.18-25.03 (Ni), 43,255-70,534 (Fe), 449-1,401 (Mn), 17.10-64.90 (Cr), 1,440-25,684 (Mg), 10,941-49,354 (Ca), 51.10-176.50 (Cu), 4,388-12,707 (Ti), 28,038-83,849 (Al), and for Hg (in nanograms gram(-1)) 0.01-0.06. Relative cumulative frequency analysis was used to determine the baseline values for the 13 metals. Compared with adjacent areas in Antarctica, Mg and Ni are significantly lower, but Cu is significantly higher than that of McMurdo Station. Enrichment factor analysis and the geo-accumulation index method were applied in order to determine the extent of anthropogenic contamination, and both show that Pb, Cd, and Hg have been significantly increased by human activities. Principal component analysis was used to identify the sources of metals in these soil samples.     

Variation of heavy metal and micro and macro element concentrations of bread and durum wheats and their relationship in grain of Turkish wheat cultivars

The 64 varieties displayed a large variation for all mineral elements, investigated Fe, Mn and Zn, ranging from 24.2 to 43.1 mg/kg, 27.6 to 64.8 mg/kg and 10.4 to 38.2 mg/kg, respectively. The mean Ca, K, Mg, Na, P and S concentrations in wheat rain varieties amounted to 378, 4,266, 1,183, 317, 3,513 and 1,542 mg/kg, respectively. Ca, K, Mg, Na, P and S contents of wheat varieties changed at the levels between 266 and 531 mg/kg, 3,029 and 5,566 mg/kg, 972 and 1,525 mg/kg, 277 and 368 mg/kg, 2,422 and 4,610 mg/kg and 1,241 to 2,052 mg/kg, respectively. The concentrations of Al, Cu, Fe, Mn and Zn of durum wheat samples were found at high levels. The mean Al, Cr, Mo, Ni, Cu, Fe, Mn and Zn concentrations in durum wheat varieties amounted to 10.93, 0.47, 0.72, 0.72, 5.37, 34.9, 37.28 and 20.88 mg/kg, respectively.     

Ferti-irrigational impact of sugar mill effluent on agronomical characteristics of Phaseolus vulgaris (L.) in two seasons

Ferti-irrigation response of 5, 10, 25, 50, 75, and 100 % concentrations of the sugar mill effluent (SME) on French bean (Phaseolus vulgaris L., cv. Annapurna) in the rainy and summer seasons was investigated. The fertigant concentrations produced significant (P?+), potassium (K⁺), calcium (Ca²⁺), magnesium (Mg²⁺), total Kjeldahl nitrogen (TKN), phosphate (PO₄ ^3?), sulfate (SO₄ ^2?), ferrous (Fe²⁺), cadmium (Cd), chromium (Cr), copper (Cu), manganese (Mn), and zinc (Zn), in both seasons. The contents of Cr, Cu, Mn, and Zn except Cd were found to be below the maximum levels permitted for soils in India. The agronomic performance of P. vulgaris was gradually increased at lower concentrations, i.e., from 5 to 25 %, and decreased at higher concentrations, i.e., from 50 to 100 %, of the SME in both seasons when compared to controls. The accumulations of heavy metals were increased in the soil and P. vulgaris from 5 to 100 % concentrations of the SME in both seasons. The contents of Cu, Mn, and Zn except Cd and Cr were noted under the permissible limit of Food and Agriculture Organization (FAO)/World Health Organization (WHO) standards. Most contents of biochemical components like crude proteins, crude fiber, and total carbohydrates were found with 25 % concentration of the SME in both seasons. The contamination factor (Cf) of various metals was in the order of Cd > Cr > Zn > Mn > Cu for soil and Mn > Zn > Cu > Cr > Cd for P. vulgaris in both seasons after fertigation with SME. Therefore, the SME can be used to improve the soil fertility and yield of P. vulgaris after appropriate dilution.     

Assessment of trace elements in the shell layers and soft tissues of the pearl oyster Pinctada radiata using multivariate analyses: a potential proxy for temporal and spatial variations of trace elements

Concentrations of trace elements (Cd, Cu, Ni, Pb, V, and Zn) were determined in the soft tissues (adductor muscle and gills) of the pearl oyster Pinctada radiata and surficial sediments from two sampling sites located in the northern part of the Persian Gulf by Graphite Furnace Atomic Absorption Spectrophotometer (GFAAS). Moreover, the levels of Li, Mg, Al, Mn, Fe, Cu, Sr, Ba, Pb, and Zn were measured in two shell layers (prismatic and nacreous) using Laser Ablation Inductively Coupled Plasma Mass Spectrometer (LA-ICP-MS). There were significant differences between the sampling sites with regard to mean concentrations of Cu, Mn, and Al in the prismatic layers of the shells. But in terms of the soft tissues, only in the case of Ni accumulation in the muscle significant differences between the sites could be observed. No significant differences could be found between the sites from the elements concentrations in the sediments point of view. The levels of Cd, Cu, Ni, and Zn in the gills were markedly higher than those in the muscle. Concentrations of Mn, Mg, Li, and Cu in the prismatic layer were significantly higher than in the nacreous but the reverse case could be found for Sr. The patterns of metal occurrence in the selected tissues, shell layers, and sediments exhibited the following descending order: Zn, Ni?>?Cd, Cu?>?V, and Pb and Zn, Ni, Cd?>?Cu, V, and Pb for muscle and gills, respectively; Zn?>?Cu, Ni, Pb, Cd, and V for sediments; Mg?>?Sr, Mn, Li, Al, Fe, Ba, Cu, Pb, and Zn for the prismatic layer; and Sr, Mg?>?Mn, Al, Fe, Li, Ba, Cu, Pb, and Zn for the nacreous layer. In most cases, the temporal variations of the elements levels in the prismatic layer were clearer than those in the nacreous layer (especially for Li, Mg, Mn, Pb, and Fe). Comparison of the gained data from this study with the other relevant researches shows that in most cases the levels of the elements in this investigation either fell within the range for other world areas or were lower. Generally, it can be concluded that the shell (especially prismatic layer) of P. radiata can be considered as a suitable proxy for temporal and spatial variations of the trace elements (and probably some environmental parameters) in the study area.     

Chemometric study on the trace metal accumulation in the sediments of the Cochin Estuary―Southwest coast of India

The distribution and accumulation of trace metals in the sediments of the Cochin estuary during the pre-monsoon, monsoon and post-monsoon periods were investigated. Sediment samples from 14 locations were collected and analysed for the metal contents (Mg, Cr, Mn, Fe, Co, Ni, Cu, Zn, Cd and Pb), organic carbon, total nitrogen, total sulphur and grain size. The data were processed using statistical tools like correlation, factor and cluster analysis. The study revealed an enrichment of Cd and Zn in the study area particularly at station 2, which is confirmed by enrichment factor, contamination factor and geoaccumulation index. The factor analysis revealed that the source of Cd and Zn may be same. The study indicated that the spatial variation for the metals like Mg, Cr, Fe, Co, Ni, Cu, Zn, Cd and Pb were predominant unlike Mn which shows a temporal variation. The strong association of trace metals with Fe and Mn hydroxides and oxides are prominent along the Cochin estuary. The anthropogenic inputs of industrial effluents mainly control the trace metals enrichment in the Cochin estuary.     

Heavy metal inputs evolution to an urban hypertrophic coastal lagoon, Rodrigo De Freitas Lagoon, Rio De Janeiro, Brazil

This work discusses the temporal variation of metal concentrations in a hypertrophic coastal lagoon located in the metropolitan area of Rio de Janeiro (Brazil). The lagoon watershed includes one of the mostly densely urbanized areas of the city but without industrial activities. Six sediment cores were collected in the lagoon between May and July 2003 and analyzed for the concentration of metals (Fe, Al, Mn, Zn, Pb, Cu, Cr, and Ni). Typical sedimentation rate was calculated as being 0.75 cm year^???1 and was uniform for at least the past 70 years. Therefore, the alterations in the dynamics of the lagoon caused by changes in its watershed were clearly indicated in sediment cores. The construction of an artificial canal to the sea and the increasing urbanization and soil use changes were the major factors affecting metal accumulation in the lagoon sediments. Metals typical of anthropogenic urban sources (Pb, Zn, and Cu) showed increasing loads following urbanization.     

Metal pollution records in core sediments of some Red Sea coastal areas, Kingdom of Saudi Arabia

In the last three decades, the industrial and human activities in the coastal area of Saudi Arabia have increased dramatically and resulted in the continuous invasion of different types of pollutants including heavy metals. Seven sediment cores were collected from three major industrialized areas; Jeddah, Rabigh and Yanbu, along the coast of Saudi Arabia to determine the spatial and temporal distribution of metals and to assess the magnitude of pollution and their potential biological effects. Sediments were analyzed for texture, calcium carbonate contents, organic matter and metals (Al, Fe, Mn, Cd, Cr, Cu, Ni, Pb and Zn). Some metals like, Cr, Mn, Ni and Zn, were enriched in the upper 15 cm of core samples (recent deposition of sediments). Cadmium concentrations showed high fluctuations with depth and reverse pattern to that for Al, Fe and Mn which indicated land based sources of this element to the studied areas. Elevated concentrations of lead were recorded in the bottom layers of cores in Jeddah that indicated the most dramatic increase in usage of gasoline in early 1970s. The calculated contamination factors (CF's) were found in the following sequences: Cd > Pb > Ni > Cu > Zn > Cr > Mn for all studied areas. Results of Pollution Load Index (PLI) revealed that Jeddah is the most polluted area, followed by Rabigh while Yanbu is the least contaminated area. Except for Ni, the concentrations of most metals in the majority of sediment samples were believed to be safe for living organisms. As no data were available on the concentration of metals in core sediments in the coastal area of Saudi Arabia, the results of this study would serve as a baseline against which future anthropogenic effects can be assessed.     

Distribution of trace metals in marine sediments of the Bay of Palma de Mallorca (Mallorca Island, Spain)

Metals were determined in surface bottom marine sediments of the Bay of Palma de Mallorca (Spain) by microwave-assisted acid-oxidant digestion and inductively coupled plasma–optical emission spectrometry in order to assess the level and distribution of potentially metallic pollutants. Average concentrations found were 1.2?±?0.3 Al and 1.9?±?0.9 Fe (in milligrams per gram), and 8?±?2 Cr, 2?±?1 Cu, 60?±?10 Mn, 4?±?1 Ni, 6?±?4 Pb, 50?±?7 Sn and 10?±?3 Zn (in micrograms per gram). Enrichment factors using normalized values to Al were also calculated which indicated that sediments were Sn and Pb enriched. Sediments were fractionated by grain size: <63, 63–250, 250–500 and >500 (in micrometres), and the metals' affinity towards the different fractions was studied. The metals' affinity to the finer fraction was evidenced, excluding Sn and Mn that showed practically no affinity for fine grains. Latent variables were extracted from the data using principal components analysis. It allowed samples to be grouped in two clusters, and most of the metals (Al, Cr, Cu, Fe, Ni, Pb and Zn) showed a similar distribution pattern. Sn and Mn showed a distinct pattern.     

Chemical fractionation of heavy metals in urban soils of Guangzhou, China

Knowledge of the total concentration of heavy metals is not enough to fully assess the environmental impact of urban soils. For this reason, the determination of metal speciation is important to evaluate their environment and the mobilization capacity. Sequential extraction technique proposed by the former European Community Bureau of Reference (BCR) was used to speciate Cd, Cu, Fe, Mn, Ni, Pb, and Zn in urban soils from Guangzhou into four operationally defined fractions: HOAc extractable, reducible, oxidizable, and residual. The Cu, Fe, Ni, and Zn were predominately located in the residual fraction, Pb in the reducible fraction, and Cd and Mn within the HOAc extractable fraction. The order of Cd in each fraction was generally HOAc extractable > reducible > residual > oxidizable; Cu and Fe were residual > reducible > oxidizable > HOAc extractable; Mn was HOAc extractable > residual > reducible > oxidizable; Ni and Zn were residual > reducible > HOAc extractable > oxidizable; and Pb was reducible > residual > oxidizable > HOAc extractable. Cadmium was identified as being the most mobile of the elements, followed by Mn, Zn, Ni, Cu, Pb and Fe. Iron–Mn oxides can play an important role in binding Cd, Cu, Ni, Pb, and Zn and in decreasing their proportion associated with the residual fraction in the soils. With total concentrations of Cd, Cu, Ni, Pb, Zn, and Mn increase, these metals more easily release and may produce more negative effects on the urban environment.     

Metal Pollution Assessment of Sediment and Water in the River Hindon, India

The metal pollution in water and sediment of the River Hindon in western Uttar Pradesh (India) was assessed for Cd, Cr, Cu, Fe, Mn, Ni, Pb and Zn. The metal concentrations in water showed wide temporal variation compared with bed sediment because of variability in water discharge and variations in suspended solid loadings. Metal concentrations in bed sediments provided a better evaluation of the degree and the extent of contamination in the aquatic environment, Santagarh and Atali being the most polluted sites of the river. The ratio of heavy metals to conservative elements (Fe, Al, etc.) may reveal the geochemical imbalances due to the elevated metal concentrations normally attributed to anthropogenic sources. Metal/Al ratios for the bed sediments of the river Hindon were used to determine the relative mobility and general trend of relative mobility occurred Fe > Mn > Zn > Cr > Ni > Pb > Cu > Cd.     

Spatial distribution and metal contamination in the coastal sediments of Al-Khafji area,Arabian Gulf,Saudi Arabia

To document the spatial distribution and metal contamination in the coastal sediments of the Al-Khafji area in the northern part of the Saudi Arabian Gulf, 27 samples were collected for Al, V, Cr, Mn, Cu, Zn, Cd, Pb, Hg, Sr, As, Fe, Co, and Ni analysis using inductively coupled plasma-mass spectrometer (ICP-MS). The results revealed the following descending order of the metal concentrations: Sr > Fe > Al > As > Mn > Ni > V > Zn > Cr > Cu > Pb > Co > Hg > Cd. Average levels of enrichment factor of Sr, As, Hg, Cd, Ni, V, Cu, Co, and Pb were higher than 2 (218.10, 128.50, 80.94, 41.50, 12.31, 5.66, 2.95, 2.90, and 2.85, respectively) and that means the anthropogenic sources of these metals, while Al, Zn, Cr and Mn have enrichment factor less than 2, which implies natural sources. Average values of Sr, Hg, Cd, Cr, Ni, and As in the coastal sediments of Al-Khafji area were mostly higher than the values recorded from the background shale and earth crust and from those results along coasts of the Caspian Sea and the Mediterranean Sea. The highest levels of Cu in the northern part of the studied coastline might be due to Al-Khafji desalination plant, while levels of Al, Ni, Cr, Fe, Mn, Pb, and Zn in the central part may be a result of landfilling and industrial sewage. The highest levels of As, Cd, Co, Cu, Hg, and V in the southern part seem to be due to oil pollutants from Khafji Joint Operations (KJO). The higher values of Sr in the studied sediments in general and particularly in locality 7 could relate to the hypersalinity and aragonitic composition of the scleractinian corals abundant in that area.     

Spatial distribution and source identification of trace elements in topsoil from heavily industrialized region,Aliaga, Turkey

Topsoil samples (n?=?40) were collected from a heavily industrialized region in Turkey. The region includes several scrap processing iron–steel plants with electric arc furnaces (EAFs), a petroleum refinery, a petrochemical complex, steel rolling mills, a natural gas-fired power plant, ship-breaking yards and very dense transportation activities. The region has undergone a rapid transition from an agricultural region to a heavily industrialized region in the last three decades. Collected soil samples were analyzed for 48 trace elements using inductively coupled plasma-mass spectrometry (ICP-MS). The elemental distribution pattern in the region indicated that Nemrut area with dense iron–steel production activities was a hotspot for elemental pollution. In addition to crustal elements, concentrations of anthropogenic trace elements (i.e., Fe, Zn, Pb, Mn, Cu, Cd, Cr and Mo) were very high in the area influencing many parts of the region. Elemental compositions of fugitive sources polluting the soil (i.e., paved and unpaved roads, slag piles, EAFs filter dust piles and coal piles) were also determined. The methods (enrichment factors [EFs] and the index of geoaccumulation [I _geo]) used for determination of pollution status of soil showed that Cr, Ag, Zn, As and Pb were the strongly contaminating elements for the region. Principal component analysis (PCA) clearly indicated that anthropogenic sources (steel production, refinery and petrochemical processes and traffic) were important sources in this region.