Auto shredder residue recycling: Mechanical separation and pyrolysis

Directive 2000/53/EC sets a goal of 85% material recycling from end-of-life vehicles (ELVs) by the end of 2015. The current ELV recycling rate is around 80%, while the remaining waste is called automotive shredder residue (ASR), or car fluff. In Europe, this is mainly landfilled because it is extremely heterogeneous and often polluted with car fluids. Despite technical difficulties, in the coming years it will be necessary to recover materials from car fluff in order to meet the ELV Directive requirement. This study deals with ASR pretreatment and pyrolysis, and aims to determine whether the ELV material recycling target may be achieved by car fluff mechanical separation followed by pyrolysis with a bench scale reactor. Results show that flotation followed by pyrolysis of the light, organic fraction may be a suitable ASR recycling technique if the oil can be further refined and used as a chemical. Moreover, metals are liberated during thermal cracking and can be easily separated from the pyrolysis char, amounting to roughly 5% in mass. Lastly, pyrolysis can be a good starting point from a "waste-to-chemicals" perspective, but further research should be done with a focus on oil and gas refining, in order both to make products suitable for the chemical industry and to render the whole recycling process economically feasible.     

End-of-Life Vehicles management: Italian material and energy recovery efficiency

Each European Member State must comply with Directive 2000/53/EC recycling and recovery targets by 2015, set to 85% and 95%, respectively. This paper reports a shredder campaign trial developed and performed in Italy at the beginning of 2008. It turns out to be the first assessment about the critical aspects belonging to the Italian End-of-Life Vehicles (ELVs) reverse supply chain involving 18 dismantling plants, a shredder plant and 630 ELV representatives of different categories of vehicles treated in Italy during 2006. This trial aims at improving the experimental knowledge related to ELVs added waste, pre-treatment, part reuse, recycling and final metal separation and car fluff disposal. Finally, the study also focuses on the calculation of the effective Italian ELV recycling rate, which results equal to 80.8%, and auto shredder residue (ASR) characterization. According to the results obtained in this work, ASR still contains up to 8% of metals and 40% of polymers that could be recovered. Moreover, physical-chemical analysis showed a Lower Heat Value of almost 20,000 kJ/kg and revealed the presence of pollutants such as heavy metals, mineral oils, PCBs and hydrocarbons.     

Strategies for the enhancement of automobile shredder residues (ASRs) recycling: Results and cost assessment

With reference to the European regulation about the management of End-of-Life Vehicles (ELVs), Directive 2000/53/EC imposes the achievement of a recycling target of 85%, and 95% of total recovery by 2015. Over the last few years many efforts have been made to find solutions to properly manage the waste coming from ELVs with the aim of complying with the targets fixed by the Directive.This paper focuses on the economical evaluation of a treatment process, that includes physical (size and density), magnetic and electrical separations, performed on the light fraction of the automobile shredder residue (ASR) with the aim of reducing the amount of waste to dispose of in a landfill and enhancing the recovery of valuable fractions as stated by the EU Directive. The afore mentioned process is able to enhance the recovery of ferrous and non-ferrous metals of an amount equal to about 1% b.w. (by weight) of the ELV weight, and to separate a high energetic-content product suitable for thermal valorization for an amount close to (but not higher than) 10% b.w. of the ELV weight.The results of the economical assessment led to annual operating costs of the treatment ranging from 300,000 €/y to 350,000 €/y. Since the considered plant treats about 13,500 metric tons of ASR per year, this would correspond to an operating cost of approximately 20–25 €/t. Taking into account the amount and the selling price of the scrap iron and of the non magnetic metal recovered by the process, thus leading to a gain of about 30 €/t per ton of light ASR treated, the cost of the recovery process is balanced by the profit from the selling of the recovered metals. On the other hand, the proposed treatment is able to achieve the fulfillment of the targets stated by Directive 2000/53/EC concerning thermal valorization and reduce the amount of waste generated from ELV shredding to landfill.     

The development and prospects of the end-of-life vehicle recycling system in Taiwan

Automobiles usually contain toxic substances, such as lubricants, acid solutions and coolants. Therefore, inappropriate handling of end-of-life vehicles (ELVs) will result in environmental pollution. ELV parts, which include metallic and non-metallic substances, are increasingly gaining recycling value due to the recent global shortage of raw materials. Hence, the establishment of a proper recycling system for ELVs will not only reduce the impact on the environment during the recycling process, but it will also facilitate the effective reuse of recycled resources. Prior to 1994, the recycling of ELVs in Taiwan was performed by related operators in the industry. Since the publishing of the “End-of-life vehicle recycling guidelines” under the authority of the Waste Disposal Act by the Environmental Protection Administration (EPA) in 1994, the recycling of ELVs in Taiwan has gradually become systematic. Subsequently, the Recycling Fund Management Board (RFMB) of the EPA was established in 1998 to collect a Collection–Disposal–Treatment Fee (recycling fee) from responsible enterprises for recycling and related tasks. Since then, the recycling channels, processing equipment, and techniques for ELVs in Taiwan have gradually become established. This paper reviews the establishment of the ELV recycling system, analyzes the current system and its performance, and provides some recommendations for future development. The reduction of auto shredder residue (ASR) is a key factor in maximizing the resource recovery rate and recycling efficiency. The RFMB needs to provide strong economic incentives to further increase the recycling rate and to encourage the automobile industry to design and market greener cars.     

Automobile Shredder Residues in Italy: characterization and valorization opportunities

At the moment Automobile Shredder Residue (ASR) is usually landfilled worldwide, but European draft Directive 2000/53/CE forces the development of alternative solutions, stating the 95%-wt recovery of an End of Life Vehicle (ELV) weight to be fulfilled by 2015. This work describes two industrial tests, each involving 250-300 t of ELVs, in which different pre-shredding operations were performed. The produced ASR materials underwent an extended characterization and some post-shredding processes, consisting of dimensional, magnetic, electrostatic and densimetric separation phases, were tested on laboratory scale, having as main purpose the enhancement of ASR recovery/recycling and the minimization of the landfilled fraction. The gathered results show that accurate depollution and dismantling operations are mandatory to obtain a high quality ASR material which may be recycled/recovered and partially landfilled according to the actual European Union regulations, with particular concern for Lower Heating Value (LHV), heavy metals content and Dissolved Organic Carbon (DOC) as critical parameters. Moreover post-shredding technical solutions foreseeing minimum economic and engineering efforts, therefore realizable in common European ELVs shredding plants, may lead to multi-purposed (material recovery and thermal valorization) opportunities for ASR reuse/recovery.     

Recycling plastics from automotive shredder residues: a review

Automotive shredder residue (ASR) is an inevitable by-product of car recycling, i.e. removal of all liquids and hazardous or valuable components from the car and shredding of the hulk, followed by the recovery of steel, iron, and non-ferrous scrap. The European Union (EU) ELV Directive requires attaining higher recovery and recycling rates, resulting in a reduction of the amount of ASR going to landfill. The most plausible methods to achieve a considerable reduction of ASR are as follows: either recycling of separated materials and dismantled bulky parts, such as bumpers, dashboards, cushions, and front and rear windows, or else systematic sorting of the commingled and size-reduced materials, resulting from shredding. After a brief comparison of the actual situation in the EU, the USA, and Japan, the characteristics of actual ASR are reviewed, as well as some of the most prominent efforts made to separate and recycle specific fractions, such as polyolefins, ABS, or polyurethane. Attention is paid to some major players in the EU and to some of the pitfalls that besiege these ventures.     

Management status of end-of-life vehicles and characteristics of automobile shredder residues in Korea

An end-of-life vehicle (ELV) is dismantled to recover and recycle any re-usable parts, then shipped to the shredding facility for further recovery of iron with any remaining Automobile Shredder Residue (ASR) to be considered as wastes and to be disposed of by either thermal treatment or landfill. Overall ELVs management status in Korea, including recycling resulting from the dismantling processes, was surveyed using some questionnaires given to dismantlers and other available information to provide some feasible means for future treatment. The averaged recycle rate in the dismantling stage showed a value of 44% and the rest of an ELV was then compressed and transported to shredding companies to recover mainly the iron content which averaged 38.7% of the mass of a new vehicle. The non-ferrous metals such as copper, antimony, zinc and aluminum accounted for only 1.5%. The Shredder dusts (SDs) were found to be composed of light and heavy fluffs and soil/dust and amounted to 15.8% based on the mass of a new vehicle. Dumping of fluff and inorganic residues into a landfill site, however, will be restricted when new regulations are implemented to reduce the disposal amount to less than 5% of a new car as done in European countries and Japan. The detailed characteristics of SDs were investigated to provide an idea of how to treat them in order to meet a future expected enforcement.     

Recycling and pollution control of the End of Life Vehicles in China

The quantity of vehicles has increased rapidly in recent years in China; however, the recycling of End of Life Vehicles (ELV) faces several problems and barriers including the collection difficulty and the environmental pollution caused by improper dismantling. In this paper, based on analysis of the basic situation regarding management and recycling of ELV in China, the ELV flow was introduced, and the potential ELV quantity was estimated. The current management regulations and policies were summarized, and dismantling and pollution control technologies for ELV recycling were introduced, too. It was suggested that with the rapid growth of ELV quantities, more regulations will be enacted, and the recycling network will be more effective; the dismantling technology and pollution control measures will be upgraded, and the recycling and remanufacturing industries will be more combined. The government should pay more attention to improve the management and supervision of, and encourage the development of, high level enterprises.     

Automotive shredder residue (ASR) characterization for a valuable management

Car fluff is the waste produced after end-of-life-vehicles (ELVs) shredding and metal recovery. It is made of plastics, rubber, glass, textiles and residual metals and it accounts for almost one-third of a vehicle mass. Due to the approaching of Directive 2000/53/EC recycling targets, 85% recycling rate and 95% recovery rate in 2015, the implementation of automotive shredder residue (ASR) sorting and recycling technologies appears strategic. The present work deals with the characterization of the shredder residue coming from an industrial plant, representative of the Italian situation, as for annual fluxes and technologies involved. The aim of this study is to characterize ASR in order to study and develop a cost effective and environmentally sustainable recycling system. Results show that almost half of the residue is made of fines and the remaining part is mainly composed of polymers. Fine fraction is the most contaminated by mineral oils and heavy metals. This fraction produces also up to 40% ashes and its LHV is lower than the plastic-rich one. Foam rubber represents around half of the polymers share in car fluff. Moreover, some chemical–physical parameters exceed the limits of some parameters fixed by law to be considered refuse derived fuel (RDF). As a consequence, ASR needs to be pre-treated in order to follow the energy recovery route.     

Status of recycling end-of-life vehicles and efforts to reduce automobile shredder residues in Korea

The present end-of-life vehicle (ELV) recycle rate and management status during the dismantling stage were investigated to aid the establishment of policies for the management of ELVs by surveying information and using the results gained from questionnaires given to dismantlers. The average recycle rate at the dismantling stage was 44% of the mass of a new vehicle and the rest of the ELV was then compressed and transported to shredding companies to recover mainly the iron content, which averaged 38.7% of the mass of a new vehicle. Nonferrous metals such as copper, antimony, zinc, and aluminum accounted for only 1.5%. The automobile shredder residues (ASRs) were composed of light and heavy fluffs and soil/dust and amounted to 15.8% based on the mass of a new vehicle. The dumping of fluff and inorganic residues in landfill sites, however, will be restricted when new regulations are implemented to reduce the disposal amount to less than 5% of a new car, as has been done in European countries and in Japan. The detailed characteristics of ASR were investigated to suggest appropriate means of treatment such as volume reduction or the utilization of thermal technologies to meet future expected enforcement. Also, some concerns on hazardous pollutant release such as that of dioxins while utilizing such thermal treatment methods were considered. The present on-going research and development projects to meet such future management targets are also introduced.     

On the ASR and ASR thermal residues characterization of full scale treatment plant

In order to obtain 85% recycling, several procedures on Automotive Shredder Residue (ASR) could be implemented, such as advanced metal and polymer recovery, mechanical recycling, pyrolysis, the direct use of ASR in the cement industry, and/or the direct use of ASR as a secondary raw material. However, many of these recovery options appear to be limited, due to the possible low acceptability of ASR based products on the market. The recovery of bottom ash and slag after an ASR thermal treatment is an option that is not usually considered in most countries (e.g. Italy) due to the excessive amount of contaminants, especially metals. The purpose of this paper is to provide information on the characteristics of ASR and its full-scale incineration residues. Experiments have been carried out, in two different experimental campaigns, in a full-scale tyre incineration plant specifically modified to treat ASR waste.Detailed analysis of ASR samples and combustion residues were carried out and compared with literature data. On the basis of the analytical results, the slag and bottom ash from the combustion process have been classified as non-hazardous wastes, according to the EU waste acceptance criteria (WAC), and therefore after further tests could be used in future in the construction industry. It has also been concluded that ASR bottom ash (EWC – European Waste Catalogue – code 19 01 12) could be landfilled in SNRHW (stabilized non-reactive hazardous waste) cells or used as raw material for road construction, with or without further treatment for the removal of heavy metals. In the case of fly ash from boiler or Air Pollution Control (APC) residues, it has been found that the Cd, Pb and Zn concentrations exceeded regulatory leaching test limits therefore their removal, or a stabilization process, would be essential prior to landfilling the use of these residues as construction material.     

End-of-life vehicle recycling and automobile shredder residue management in Japan

The Japanese Government introduced the Law on Recycling of End-of-Life Vehicles (ELV Recycling Law) in 2002. This law requires manufacturers to retrieve chlorofluorocarbons (CFCs), airbags, and automobile shredder residue (ASR) from ELVs and to properly recycle the remaining materials. This framework is compared with European ELV directives. Pilot-scale incineration plant testing has revealed a greater formation of by-product persistent organic pollutants (POPs) during the primary combustion of ASR compared to normal municipal solid waste. This may be attributed to the abundance of chlorine, Cu, and Fe in ASR, as Cu and Fe have been found to catalyze the formation of POPs under certain conditions. However, most by-product POPs were destroyed by the secondary combustion, and almost all were removed after flue gas treatment. The direct melting system is a shaft-type gasification and melting technology that has proved effective in many municipal solid waste applications. This system can be applied to ASR recycling for effective decomposition of brominated flame retardants and polybrominated dioxins.     

Energy efficiency of substance and energy recovery of selected waste fractions

In order to reduce the ecological impact of resource exploitation, the EU calls for sustainable options to increase the efficiency and productivity of the utilization of natural resources. This target can only be achieved by considering resource recovery from waste comprehensively. However, waste management measures have to be investigated critically and all aspects of substance-related recycling and energy recovery have to be carefully balanced. This article compares recovery methods for selected waste fractions with regard to their energy efficiency.Whether material recycling or energy recovery is the most energy efficient solution, is a question of particular relevance with regard to the following waste fractions: paper and cardboard, plastics and biowaste and also indirectly metals. For the described material categories material recycling has advantages compared to energy recovery. In accordance with the improved energy efficiency of substance opposed to energy recovery, substance-related recycling causes lower emissions of green house gases.For the fractions paper and cardboard, plastics, biowaste and metals it becomes apparent, that intensification of the separate collection systems in combination with a more intensive use of sorting technologies can increase the extent of material recycling. Collection and sorting systems must be coordinated. The objective of the overall system must be to achieve an optimum of the highest possible recovery rates in combination with a high quality of recyclables.The energy efficiency of substance related recycling of biowaste can be increased by intensifying the use of anaerobic technologies. In order to increase the energy efficiency of the overall system, the energy efficiencies of energy recovery plants must be increased so that the waste unsuitable for substance recycling is recycled or treated with the highest possible energy yield.     

Brominated flame retardants and heavy metals in automobile shredder residue (ASR) and their behavior in the melting process

The End-of-life Vehicles Recycling Act went into effect on January 1, 2005, in Japan and requires the proper treatment of airbags, chlorofluorocarbons (CFCs), and automobile shredder residue (ASR). The need for optimal treatment and recycling of ASR, in particular, has been increasing year after year because ASR is regarded as being difficult to treat. Dioxin-related compounds, brominated flame retardants (BFRs), heavy metals, chlorine and organotin compounds are all present in high concentrations in ASR. The authors conducted ASR melting treatment tests using a 10-tons/day-scale direct melting system (DMS), which employs shaft-type gasification and melting technology. The results obtained showed that dioxin-related compounds and BFRs were decomposed by this melting treatment. The high-temperature reducing atmosphere in the melting furnace moved volatile heavy metals such as lead and zinc into the fly ash where they were distributed at a rate of more than 90% of the input amount. This treatment was also found to be effective in the decomposition of organotin, with a rate of decomposition higher than 99.996% of the input amount. Via the recovery of heavy metals concentrated in the fly ash, all the products discharged from this treatment system were utilized effectively for the complete realization of an ASR recycling system that requires no final disposal sites.     

Full scale treatment of ASR wastes in a modified rotary kiln

A plant, designed for the thermo-valorisation of tyres, was specifically modified in order to treat Automobile Shredder Residue (ASR). Results from two full-scale combustion experiments, carried out on large ASR feeding lots (thousands of tons) indicate the proposed technology as a potential route to help the fulfilling of impending 95% reuse and recovery target set by the End of life Vehicle (ELV) Directive (January 2015). The paper describes the main operational troubleshot occurred during the first experiment (emissions at the stack out of regulatory limits and problems of clogging on the conveyer belt) and the consequent upgrading solutions (pre-treatment, introduction of waste double low-flow screw feeder and a cyclone prior to the main fan, modification of rotatory kiln inlet) adopted to allow, during the second long-term experiment, a continuous basis operation of the plant in full compliance with the discharge limit to the atmosphere. Characterization of both ASR and combustion residues allowed to quantify a 18% of combustion residues as not dangerous waste while only the 2% as hazardous one. A pre-treatment for the reduction of fines in the ASR was recommended in order to achieve the required energy recovery efficiency.     

WEEE flow and mitigating measures in China

The research presented in this paper shows that Waste Electrical and Electronic Equipment (WEEE) issues associated with home appliances, such as TV sets, refrigerators, washing machines, air conditioners, and personal computers, are linked in the WEEE flow and recycling systems and are important to matters of public policy and regulation. In this paper, the sources and generation of WEEE in China are identified, and WEEE volumes are calculated. The results show that recycling capacity must increase if the rising quantity of domestic WEEE is to be handled properly. Simultaneously, suitable WEEE treatment will generate large volumes of secondary resources. Environmental problems caused by the existing recycling processes have been investigated in a case study. Problems mainly stem from open burning of plastic-metal parts and from precious metals leaching techniques that utilize acids. The existing WEEE flow at the national level was investigated and described. It became obvious that a considerable amount of obsolete items are stored in homes and offices and have not yet entered the recycling system. The reuse of used appliances has become a high priority for WEEE collectors and dealers because reuse generates higher economic profits than simple material recovery. The results of a cost analysis of WEEE flow shows that management and collection costs significantly influence current WEEE management. Heated discussions are ongoing in political and administrative bodies as to whether extended producer responsibilities policies are promoting WEEE recycling and management. This paper also discusses future challenges and strategies for WEEE management in China.     

报废汽车非金属材料资源化利用研究

随着大量汽车进入报废期,如何对报废汽车进行资源化再利用成为人们面临的重要课题。报废汽车上的非金属材料,由于种类多、组成复杂,资源化再利用的难度较大,大多被废弃,会造成资源浪费、环境污染等一系列问题。塑料、橡胶、玻璃是汽车中主要的非金属材料,这些物质的资源化利用,对改善环境、节约资源,具有极大的社会经济效益。着重对报废汽车中塑料、橡胶、玻璃主要非金属材料的资源化利用技术现状进行研究,探究提高其回收利用水平的思路,对报废汽车非金属材料的资源化再利用提供一定的参考。     

Critical enablers and inhibitors for economic sustainability in the supply and demand of end-of-life vehicles in Malaysia: a SWOT analysis

Journal of Material Cycles and Waste Management - End-of-life vehicles (ELV) management is essential for sustainable development and waste minimization. However, the ELV recycling companies are...     

Comparison of end-of-life vehicle material flows for reuse,material recycling,and energy recovery between Japan and the European Union

Journal of Material Cycles and Waste Management - Japan and the European Union (EU) both have well-established End-of-Life Vehicle (ELV) policies and management systems. However, due to the...     

Review of Italian experience on automotive shredder residue characterization and management

Automotive Shredder Residue (ASR) is a special waste that can be classified as either hazardous or non hazardous depending on the amount of hazardous substances and on the features of leachate gathered from EN12457/2 test. However both the strict regulation concerning landfills and the EU targets related to End-of-Life Vehicles (ELVs) recovery and recycling rate to achieve by 2015 (Directive 2000/53/EC), will limit current landfilling practice and will impose an increased efficiency of ELVs valorization. The present paper considers ELVs context in Italy, taking into account ASRs physical–chemical features and current processing practice, focusing on the enhancement of secondary materials recovery. The application in waste-to-energy plants, cement kilns or metallurgical processes is also analyzed, with a particular attention to the possible connected environmental impacts. Pyrolysis and gasification are considered as emerging technologies although the only use of ASR is debatable; its mixing with other waste streams is gradually being applied in commercial processes. The environmental impacts of the processes are acceptable, but more supporting data are needed and the advantage over (co-)incineration remains to be proven.