Feasibility of Soil Dust Source Apportionment by the Pyrolysis-Gas Chromatography/Mass Spectrometry Method

Abstract

This study tested the feasibility of using pyrolysis (Py)-gas chromatography (GC)/mass spectrometry (MS) to obtain organic chemical species data suitable for source apportionment modeling of soil-derived coarse particulate matter (PM₁₀) dust on ambient filters. A laboratory resuspension apparatus was used with known soils to generate simulated receptor filter samples loaded with ～0.4 mg of PM₁₀ dust, which is within the range of mass loading on ambient filters. Py-GC/MS at 740 °C generated five times more resolvable compounds than were obtained with thermal desorption GC/MS at 315 °C. The identified compounds were consistent with literature from Py experiments using larger samples of bulk soils. A subset of 91 organic species out of the 178 identified Py products was used as input to CMB8 software in a demonstration of source apportionment using laboratory-generated mixtures simulating ambient filter samples. The 178 quantified organic species obtained by Py of soil samples is an improvement compared with the 38 organic species obtained by thermal desorption of soils and the four functionally defined organic fractions reported by thermal/optical reflectance. Significant differences in the concentration of specific species were seen between samples from different sites, both geographically distant and close, using analysis of variance and cluster analysis. This feasibility study showed that Py-GC/MS can generate useful source profile data for receptor modeling and justifies continued method development.     

Application of 1D and 2D MFR reactor technology for the isolation of insecticidal and anti-microbial properties from pyrolysis bio-oils

Valuable chemicals can be separated from agricultural residues by chemical or thermochemical processes. The application of pyrolysis has already been demonstrated as an efficient means to produce a liquid with a high concentration of desired product. The objective of this study was to apply an insect and microorganism bioassay-guided approach to separate and isolate pesticidal compounds from bio-oil produced through biomass pyrolysis. Tobacco leaf (Nicotianata bacum), tomato plant (Solanum lycopersicum), and spent coffee (Coffea arabica) grounds were pyrolyzed at 10°C/min from ambient to 565°C using the mechanically fluidized reactor (MFR). With one-dimensional (1D) MFR pyrolysis, the composition of the product vapors varied as the reactor temperature was raised allowing for the selection of the temperature range that corresponds to vapors with a high concentration of pesticidal properties. Further product separation was performed in a fractional condensation train, or 2D MFR pyrolysis, thus allowing for the separation of vapor components according to their condensation temperature. The 300–400°C tobacco and tomato bio-oil cuts from the 1D MFR showed the highest insecticidal and anti-microbial activity compared to the other bio-oil cuts. The 300–350 and 350–400°C bio-oil cuts produced by 2D MFR had the highest insecticidal activity when the bio-oil was collected from the 210°C condenser. The tobacco and tomato bio-oil had similar insecticidal activity (LC₅₀ of 2.1 and 2.2 mg/mL) when the bio-oil was collected in the 210°C condenser from the 300–350°C reactor temperature gases. The 2D MFR does concentrate the pesticidal products compared to the 1D MFR and thus can reduce the need for further separation steps such as solvent extraction.     

Reaction of arsenic vapor species with fly ash compounds: kinetics and speciation of the reaction with calcium silicates

In coal combustion systems, the partitioning of arsenic between the vapor and solid phases is determined by the interaction of arsenic vapors with fly ash compounds under post-combustion conditions. This partitioning is affected by gas–solid reactions between the calcium components of the ash particles and arsenic vapors. In this study, bench scale experiments were conducted with calcium compounds typical of coal-derived fly ash to determine product formation, the extent of reaction and reaction rates when contacted by arsenic oxide vapors. Experiments conducted with arsenic trioxide (As₄O_6(g)) vapors in contact with calcium oxide, di-calcium silicate and mono-calcium silicate over the temperature range 600–1000 °C indicated that these solids were capable of reacting with arsenic vapor species in both air and nitrogen. Calcium arsenate was the observed reaction product in all the samples analyzed. Maximum capture of arsenic occurred at 1000 °C with calcium oxide being the most effective of the three solids over the range of temperatures studied. Using a shrinking core model for a first order reaction and the results from intrinsic kinetic experiments conducted in air, the reaction rate constants were found to be 1.4×10⁻³exp(−2776/T) m/s for calcium oxide particles, 7.2×10⁻³exp(−3367/T) m/s for di-calcium silicate particles and 5.5×10⁻³exp(−3607/T) m/s for mono-calcium silicate particles. These results therefore suggest that any calcium present in fly ash can react with arsenic vapor and capture the metal in water-insoluble forms of the less hazardous As(V) oxidation state.     

Residues of organochlorine and organophosphorus pesticides in sugarcane crop soils and river water

The presence of residual organochlorine and organophosphorus pesticides was evaluated at different periods of sugarcane cultivation in agricultural soil and water samples from the town of Tlaltizapan, which is located in the state of Morelos in Mexico, to determine the presence and persistence of these compounds and their possible effects on the region. The compounds p,p′-DDE, p,p′-DDD (metabolites of p,p′-DDT), γ-HCH and heptachlor were found in more of 95% of the sampling zones in the three monitoring periods performed along 2 years. The highest concentration detected (129.6 μg/kg _{dry soil}) was for α-HCH, but its frequency of detection was ～5%. The low detection frequency of α-HCH and the high concentration values of γ-HCH indicate the repeated use of technical-grade HCH and Lindane (γ-HCH) in the region. Among the organophosphorus pesticides, ethyl parathion was the compound with the highest soil concentration, at ～2000 μg/kg_{dry soil}, during the initial monitoring. However, this compound was detected in the second monitoring with a concentration of ～4 μg/kg_{dry soil}, but it was not detected in the third, indicating that is was not accumulated in the environment. The heptachlor was the compound most commonly found in all water samples, within a range of 0.45–1.25 ng/L. The presence of this organochlorine compound in the water samples indicated a possible migration from the soil to water bodies due to soil erosion. The presence of organophosphorus compounds was not detected in the water samples, which could be attributed to the moderate persistence of these compounds and their consequent degradation before arriving at the water bodies.     

Effect of pH on surface characteristics of switchgrass-derived biochars produced by fast pyrolysis

Surface properties of switchgrass-derived biochars produced at fast pyrolysis temperatures of 450, 600 and 800 °C were characterized at different solution pHs in order to determine the structural and chemical changes of artificially-weathered biochars when incorporated into soil. As biochars were acidified from pH 7 to 3, crystalline minerals dissolved slowly releasing nutrients; however, residual minerals were still detected in biochars produced at higher pyrolysis temperatures after pH treatment. Moreover, the amount of exchangeable bases and other inorganic compounds released from the biochars increased when pH decreased. As minerals dissolved from the biochars, total surface area and pore volume were found to increase. Surface functional groups and water vapor adsorption capacity at 0.8 P/P_o also increased, whereas the potential CEC of biochars decreased due to the replacement of exchangeable sites by hydrogen ion. Therefore, during the aging process, it is predicted that soil-incorporated biochars will slowly release nutrients with changes in surface functionality and porosity, which are expected to enhance water holding capacity of soil and provide a beneficial habitat for microbial colonization.     

Assessment of natural and calcined starfish for the amelioration of acidic soil

Quality improvement of acidic soil (with an initial pH of approximately 4.5) with respect to soil pH, exchangeable cations, organic matter content, and maize growth was attempted using natural (NSF) and calcined starfish (CSF). Acidic soil was amended with NSF and CSF in the range of 1 to 10 wt.% to improve soil pH, organic matter content, and exchangeable cations. Following the treatment, the soil pH was monitored for periods up to 3 months. The exchangeable cations were measured after 1 month of curing. After a curing period of 1 month, the maize growth experiment was performed with selected treated samples to evaluate the effectiveness of the treatment. The results show that 1 wt.% of NSF and CSF (700 and 900 °C) were required to increase the soil pH to a value higher than 7. In the case of CSF (900 °C), 1 wt.% was sufficient to increase the soil pH value to 9 due to the strong alkalinity in the treatment. No significant changes in soil pHs were observed after 7 days of curing and up to 3 months of curing. Upon treatment, the cation exchange capacity values significantly increased as compared to the untreated samples. The organic content of the samples increased upon NSF treatment, but it remains virtually unchanged upon CSF treatment. Maize growth was greater in the treated samples rather than the untreated samples, except for the samples treated with 1 and 3 wt.% CSF (900 °C), where maize growth was limited due to strong alkalinity. This indicates that the amelioration of acidic soil using natural and calcined starfish is beneficial for plant growth as long as the application rate does not produce alkaline conditions outside the optimal pH range for maize growth.     

Effects of copper fungicide residues on the microbial function of vineyard soils

The use of copper-based fungicides leads to an accumulation of copper (Cu) in vineyard soils, potentially causing adverse effects to the microbial function and fertility of the soil. This study used a soil microcosm approach to assess the effects of Cu accumulation on microbial function in vineyard soils. Surface soil samples were collected from 10 vineyards and a number of un-impacted reference sites in each of three different viticultural regions of Australia. The field-collected soils were transferred to microcosms and maintained for up to 93 days in the laboratory at 20–22 °C and 60 % of their maximum water-holding capacity. The microbial function of the soils was indicated by measuring phosphomonoesterase, arylsulfatase, urease, and phenol oxidase activities. In general, the vineyard soils had greater concentrations of Cu and lower enzyme activities than in the reference soils, although a weak negative relationship between Cu and enzyme activity could only be found for phosphomonoesterase activity. The results show that soil physical–chemical properties (i.e., organic carbon, pH) are greater determinants of soil enzyme activity than increased soil Cu concentration at the Cu concentrations present in vineyard soils.     

Evaluation of B. subtilis SPB1 biosurfactants' potency for diesel-contaminated soil washing: optimization of oil desorption using Taguchi design

Low solubility of certain hydrophobic soil contaminants limits remediation process. Surface-active compounds can improve the solubility and removal of hydrophobic compounds from contaminated soils and, consequently, their biodegradation. Hence, this paper aims to study desorption efficiency of oil from soil of SPB1 lipopeptide biosurfactant. The effect of different physicochemical parameters on desorption potency was assessed. Taguchi experimental design method was applied in order to enhance the desorption capacity and establish the best washing parameters. Mobilization potency was compared to those of chemical surfactants under the newly defined conditions. Better desorption capacity was obtained using 0.1 % biosurfacatnt solution and the mobilization potency shows great tolerance to acidic and alkaline pH values and salinity. Results show an optimum value of oil removal from diesel-contaminated soil of about 87 %. The optimum washing conditions for surfactant solution volume, biosurfactant concentration, agitation speed, temperature, and time were found to be 12 ml/g of soil, 0.1 % biosurfactant, 200 rpm, 30 °C, and 24 h, respectively. The obtained results were compared to those of SDS and Tween 80 at the optimal conditions described above, and the study reveals an effectiveness of SPB1 biosurfactant comparable to the reported chemical emulsifiers. (1) The obtained findings suggest (a) the competence of Bacillus subtilis biosurfactant in promoting diesel desorption from soil towards chemical surfactants and (b) the applicability of this method in decontaminating crude oil-contaminated soil and, therefore, improving bioavailability of hydrophobic compounds. (2) The obtained findings also suggest the adequacy of Taguchi design in promoting process efficiency. Our findings suggest that preoptimized desorption process using microbial-derived emulsifier can contribute significantly to enhancement of hydrophobic pollutants' bioavailability. This study can be complemented with the investigation of potential role in improving the biodegradation of the diesel adsorbed to the soil.     

Occurrence and analysis of selected pharmaceutical compounds in soil from Spanish agricultural fields

This work describes the analysis of 15 pharmaceutical compounds, belonging to different therapeutic classes (anti-inflammatory/analgesics, lipid regulators, antiepileptics, β-blockers and antidepressants) and with diverse physical–chemical properties, in Spanish soils with different farmland uses. The studied compounds were extracted from soil by ultrasound-assisted extraction (UAE) and determined, after derivatization, by gas chromatography with mass spectrometric detection (GC–MS). The limits of detection (LODs) ranged from 0.14 ng g^?1 (naproxen) to 0.65 ng g^?1 (amitriptyline). At least two compounds where detected in all samples, being ibuprofen, salicylic acid, and paracetamol, the most frequently detected compounds. The highest levels found in soil were 47 ng g^?1 for allopurinol and 37 ng g^?1 for salicylic acid. The influence of the type of crop and the sampling area on the levels of pharmaceuticals in soil, as well as their relationship with soil physical–chemical properties, was studied. The frequent and widespread detection of some of these compounds in agricultural soils show a diffuse contamination, although the low levels found do not pose a risk to the environment or the human health.     

Adsorption of organic vapors on polar surfaces- Recent advances

This paper summarizes recent research on the adsorption of organic vapors on surfaces. Since the low gas phase concentration range is typical for environmental situations, this review is restricted to these adsorption coefficients. Two environmental parameters have a strong influence on the adsorption of organic vapors on polar surfaces:temperature andrelative humidity (which is the most suitable parameter for describing the influence of ambient moisture). An exponential relationship was found for the adsorption coefficientversus relative humidity and the reciprocal temperature, respectively. Comparing the heats of adsorption, two different groups of substances emerged: polar chemicals exhibited heats of sorption which were higher than their corresponding heats of condensation due to their ability to form hydrogen bonds, while for the nonpolar compounds the opposite was true. Sorption takes place on the surface of an adsorbed water film when the relative humidity exceeds the value which is necessary to form a monomolecular layer of water on the surface of the adsorbent (≥ 30 % relative humidity). Therefore, at temperature below 0 °C, a change in the adsorption behavior might be expected due to a change of properties of the adsorbed water film. However, no alterations were observed at temperatures from -12 °C to + 4 °C (adsorption on quartz sand). The results were comparable to those at much higher temperatures (50 – 80 °C). A statistical approach for the prediction of the adsorption coefficients from physico-chemical parameters of the substances (vapor pressure, polarizability, and electron-donating capability) was developed and good agreement was found with experimental results and independent data from the literature. Finally, two special cases, the adsorption on bulk water and ice, are discussed.     

Effect of temperature and particle size on the thermal desorption of PCBs from contaminated soil

Thermal desorption is widely used for remediation of soil contaminated with volatiles, such as solvents and distillates. In this study, a soil contaminated with semivolatile polychlorinated biphenyls (PCBs) was sampled at an interim storage point for waste PCB transformers and heated to temperatures from 300 to 600 °C in a flow of nitrogen to investigate the effect of temperature and particle size on thermal desorption. Two size fractions were tested: coarse soil of 420–841 μm and fine soil with particles <250 μm. A PCB removal efficiency of 98.0 % was attained after 1 h of thermal treatment at 600 °C. The residual amount of PCBs in this soil decreased with rising thermal treatment temperature while the amount transferred to the gas phase increased up to 550 °C; at 600 °C, destruction of PCBs became more obvious. At low temperature, the thermally treated soil still had a similar PCB homologue distribution as raw soil, indicating thermal desorption as a main mechanism in removal. Dechlorination and decomposition increasingly occurred at high temperature, since shifts in average chlorination level were observed, from 3.34 in the raw soil to 2.75 in soil treated at 600 °C. Fine soil particles showed higher removal efficiency and destruction efficiency than coarse particles, suggesting that desorption from coarse particles is influenced by mass transfer.     

Distribution,possible sources,and health risk assessment of SVOC pollution in small streams in Pearl River Delta,China

The pollution levels of typical semivolatile organic compounds (SVOCs) consisting of 15 polycyclic aromatic hydrocarbons (PAHs), 20 organic chlorinated pesticides (OCPs), and 15 phthalate esters (PAEs) were investigated in small rivers running through the flourishing cities in Pearl River Delta region, China. The concentrations of ∑15PAHs were 2.0–48 ng/L and 29–1.2?×?10³ ng/g in the water and sediment samples, respectively. The ∑20OCPs were 6.6–57 ng/L and 9.3–6.0?×?10² ng/g in the water and sediment samples, respectively. The concentrations of ∑15PAEs were much higher both in the water and sediments. The partition process of the detected SVOCs between the water and sediment did not reach the equilibrium state at most of the sites when sampling. The combustion of petroleum products and coal was the major source of the detected PAHs. The OCPs were mainly historical residue, whereas the new inputs of dichlorodiphenyltrichloroethane (DDT), chlordane, and endosulfan were possible at several sites. The industrial and domestic sewage were the major source for the PAEs; storm water runoff accelerated the input of PAEs. No chronic risk of the SVOCs was identified by a health risk assessment through daily water consumption, except for the ∑20OCPs that might cause cancer at several sites. Nevertheless, the integrated health risk of the SVOCs should not be neglected and need intensive investigations.     

A New Audit Technique for EPA Method 25

A simple, inexpensive, and accurate technique for evaluating or auditing the sampling, recovery, and analytical phases of EPA Source Reference Method 25 has been developed. The technique involves spiking a U-shaped stainless steel cartridge containing Tenax® with known quantities of selected organic compounds and thermally desorbing them at temperatures from 160°C to 180°C to generate organic vapors quantitatively. The major advantages of this technique are that no other measurement methods can be used to determine the generated organic concentrations in lieu of Method 25; and that the cartridge can easily be taken to the field for evaluation. The organic compounds generated in test runs are collected and analyzed using the Method 25 procedure. The generation of organics is quantitative and recoveries were found to be 100 ± 10%. The time required for desorption of the majority of organics is generally less than forty-five minutes at a flow rate of 100 mL/min; however, based on laboratory experience the recommended sampling time is sixty minutes. These spiked cartridges are stable at room temperature over a two-month period. Results of interlaboratory studies showed close agreement with the expected concentrations based on calculations from the mass loadings and sample volumes.     

Effects of soil moisture and physical-chemical properties of organic pollutants on vapor-phase transport in the vadose zone

Vapor-phase transport of organic pollutants is one of the important pathways in the distribution and attenuation of volatile organic compounds in the vadose zone. In this study, the impact of vapor-phase partitioning and of the physical-chemical properties of organic pollutants on vapor-phase transport was assessed. An experimentally derived relationship to predict vapor sorption for a variety of soil types under varying soil moisture conditions was incorporated into the two-dimensional finite-element model, Vocwaste. The revised model was then used to simulate the transport of volatile organics. Vapor-phase partitioning in the model accounted for vapor uptake by sorption onto moist mineral surfaces as well as sorption at the liquid-solid interface and dissolution into soil water. Under dry conditions, vapor-phase sorption of volatile organic pollutants was shown to have a retarding effect on transport of organic vapors. However, for shallow, contaminated soils, volatilization was controlled by vapor diffusion, even under dry conditions where vapor-phase sorption was high. The influence of Henry's law constant and of the aqueous-phase (solid-liquid) partition coefficient for volatile organic pollutants was considered in the simulations. Volatilization of organic vapors was shown to be favored for contaminants with high Henry's law constants and low aqueous-phase partitioning coefficients. Because of the interdependence of these two physical-chemical properties, individual properties of the contaminant should not be considered in isolation in the evaluation of vapor transport.     

Protecting Off-Site Populations and Site Workers from Vapor Discharges during Shallow Soil Mixing at the North Carolina State University National Priorities List Site

Abstract

Although vapor monitoring is generally a component of remedial action activities, most sites do not have routine gaseous releases or vapor clouds erupting from the soil during implementation of the cleanup process (or during cleanup of the site). At the North Carolina State University Lot 86 National Priorities List Site, over 8410 m³ (11,000 yd³) of chemical waste was disposed at the Site, including organic solvents and shock-sensitive and airand water-reactive compounds. During the Remedial Action, it was imperative to protect site workers and off-site populations from potential inhalation exposures. Engineering controls were incorporated into the shallow soil mixing process to limit the release of gaseous compounds. To quantify potential exposures to on-site and off-site receptors, modeling was conducted to evaluate potential exposure routes and migration pathways. To demonstrate acceptable levels of airborne constituents, a multifaceted air sampling and monitoring program was implemented. To ensure that potential exposures could be quantified, passive dosimeters, continuous real-time monitoring, time-weighted whole air sampling, and grab samples of vapor clouds were all critical components of the air monitoring program. After the successful completion of the Remedial Action, the pre-Resource Conservation and Recovery Act (RCRA) chemical waste generated from the University’s educational and research laboratories was entirely encapsulated and neither on-site workers nor off-site populations were exposed to analyzed compounds above any health-based action level (i.e., 15-min short-term exposure limit [STEL], 8-hr threshold limit value, or time-weighted average permissible exposure limit)     

Comparative assessment of coal tars obtained from 10 former manufactured gas plant sites in the eastern United States

A comparative analysis was performed on eleven coal tars obtained from former manufactured gas plant sites in the eastern United States. Bulk properties analyzed included percent ash, Karl Fisher water content, viscosity and average molecular weight. Chemical properties included monocyclic- and polycyclic-aromatic hydrocarbon (PAH) concentrations, alkylated aromatic concentrations, and concentrations of aliphatic and aromatic fractions. It was found that there was at least an order-of-magnitude variation in all properties measured between the eleven coal tars. Additionally, two coal tars obtained from the same manufactured gas plant site had very different properties, highlighting that there can be wide variations in coal tar properties from different samples obtained from the same site. Similarities were also observed between the coal tars. The relative chemical distributions were similar for all coal tars, and the coal tars predominantly consisted of PAHs, with naphthalene being the single-most prevalent compound. The C(9-22) aromatic fraction, an indicator of all PAHs up to a molecular weight of approximately 276 gmole(-1), showed a strong power-law relationship with the coal tar average molecular weight (MW (ct)). And the concentrations of individual PAHs decreased linearly as MW (ct) increased up to ca. 1000 gmole(-1), above which they remained low and variable. Implications of these properties and their variation with MW (ct) on groundwater quality are discussed. Ultimately, while these similarities do allow generalities to be made about coal tars, the wide range of coal tar bulk and chemical properties reported here highlights the complex nature of coal tars.     

Natural and enhanced biodegradation of propylene glycol in airport soil

Aircraft de-icing fluids (ADF) are a source of water and soil pollution in airport sites. Propylene glycol (PG) is a main component in several commercial formulations of ADFs. Even though PG is biodegradable in soil, seasonal overloads may result in occasional groundwater contamination. Feasibility studies for the biostimulation of PG degradation in soil have been carried out in soil slurries, soil microcosms and enrichment cultures with and without the addition of nutrients (N and P sources, oligoelements), alternative electron acceptors (nitrate, oxygen releasing compounds) and adsorbents (activated carbon). Soil samples have been taken from the contaminated area of Gardermoen Airport Oslo. Under aerobic conditions and in the absence of added nutrients, no or scarce biomass growth is observed and PG degradation occurs by maintenance metabolism at constant removal rate by the original population of PG degraders. With the addition of nutrient, biomass exponential growth enhances aerobic PG degradation also at low temperatures (4 ° C) that occur at the high season of snowmelt. Anaerobic PG degradation without added nutrients still proceeds at constant rate (i.e. no biomass growth) and gives rise to reduced fermentation product (propionic acid, reduced Fe and Mn, methane). The addition of nitrate does not promote biomass growth but allows full PG mineralization without reduced by-products. Further exploitation on the field is necessary to fully evaluate the effect of oxygen releasing compounds and adsorbents.     

Properties of biochars from conventional and alternative feedstocks and their suitability for metal immobilization in industrial soil

In contaminated soils, excessive concentrations of metals and their high mobility pose a serious environmental risk. A suitable soil amendment can minimize the negative effect of metals in soil. This study investigated the effect of different biochars on metal (Cu, Pb, Zn) immobilization in industrial soil. Biochars produced at 300 and 600 °C from conventional (MS, maize silage; WP, wooden pellets) and alternative (SC, sewage sludge compost; DR, digestate residue) feedstocks were used as soil amendments at a dosage of 10 % (w/w). The type of feedstock and pyrolysis temperature affected the properties of the biochars and their ability to immobilize metal in soil. Compared to production at 300 °C, all biochars produced at 600 °C had higher pH (6.2–10.7), content of ash (7.2–69.0 %) and fixed carbon (21.1–56.7 %), but lower content of volatile matter (9.7–37.2 %). All biochars except DR biochar had lower dissolved organic carbon (DOC) content (1.4–2.3 g C/L) when made at 600 °C. Only MS and SC biochars had higher cation exchange capacity (25.2 and 44.7 cmol/kg, respectively) after charring at 600 °C. All biochars contained low concentrations of Cd, Cu, Ni, Pb and Zn; Cd was volatilized to the greatest extent during pyrolysis. Based on FTIR analysis and molar ratios of H/C and O/C, biochars had a greater degree of carbonization and aromaticity after charring at 600 °C. The efficiency of the biochars in metal immobilization depended mainly on their pH, ash content, and concentration of DOC. SC and DR biochars were more effective for Cu and Zn immobilization than MS and WP biochars, which makes them attractive options for large-scale soil amendment.     

Microbial and physicochemical parameters associated with Legionella contamination in hot water recirculation systems

Hot water recirculation systems (HWRS) in hotels and nursing homes, which are common in countries such as Spain, have been related to outbreaks of legionellosis. To establish the relationships of microbial and physicochemical parameters, especially protozoa, with the occurrence of Legionella in HWRS, 231 samples from hotels and nursing homes were analysed for Legionella, protozoa, heterotrophic plate counts (HPC) at 22 and 37 °C, Pseudomonas, metals, temperature and others. Legionella pneumophila was the dominant species isolated, and 22 % were sg. 1. The sampling method became particularly important in order to define which factors were involved on the occurrence of Legionella. Results showed that the bacteria and the accompanying microbiota were more abundant in the first flush water whose temperature was lower. The bacteria occurred in those samples with high HPC and were inversely correlated with high temperatures. Multivariate regression showed that a concentration above 1?×?10⁵?CFU/100 mL of HPC at 37 °C, Fe above 0.095 ppm and the presence of protozoa increased significantly the risk of Legionella colonization, while univariant regression showed that the presence of Cu above 0.76 ppm and temperature above 55 °C diminished it. Therefore, to reduce the risk associated with Legionella occurrence in HWRS these parameters should be taken into consideration.     

Persistence of azadirachtin A and B in soil: Effects of temperature and microbial activity

Abstract

The persistence of two insecticidally active compounds from the neem tree, azadirachtin A and B, was determined at two different temperatures (15 and 25°C) in the laboratory after application of the commercial neem insecticide, Margosan‐O, to a sandy loam soil. The influence of microbial activity on degradation was also examined by comparing autoclaved and non‐autoclaved soils also at 15 and 25°C. Temperature influenced degradation rates. The DT ₅₀ (time required for 50% disappearance of the initial concentration) for azadirachtin A was 43.9 and 19.8 d for non‐autoclaved soil kept at 15 and 25°C, respectively. The DT ₅₀ for azadirachtin B was 59.2 and 20.8 d for non‐autoclaved soil kept at 15 and 25°C, respectively. Microbial activity was also responsible for faster degradation because DT ₅₀ ’s for autoclaved soil were much longer than for non‐autoclaved soils. DT ₅₀ ‘_s for azadirachtin A in autoclaved soil were 91.2 (15°C) and 31.5 d (25°C). DT50’s for azadirachtin B in autoclaved soil were 115.5 (15°C) and 42.3 d (25°C). Two degradation products of azadirachtin were detected, but were not identified. Higher levels of the two degradation products were detected in non‐autoclaved soil.