苜蓿根瘤菌对多氯联苯降解转化特性研究

采用溶液摇瓶实验研究了苜蓿根瘤菌(Rhizobium meliloti)对三氯代联苯(2,4,4′-trichlorobiphenyl)单体以及18种多氯联苯(polychlorinated biphenyls,PCBs)混合物的降解转化能力.结果表明,接入苜蓿根瘤菌转化7d后,随着溶液中底物2,4,4′-TCB浓度的增加,该菌株对其的降解能力也逐渐提高,在1.0、5.0、10.0、25.0、50.0 mg.L-1浓度条件下该菌对2,4,4′-TCB的降解率分别为34.0%、48.3%、69.7%、96.0%、98.5%,并且通过气相质谱分析,发现溶液中出现了一些新的代谢产物.同时,苜蓿根瘤菌对不同浓度下18种PCBs同系物混合物的降解能力,随着底物浓度的升高呈现出从低到高,然后降低,并趋于平衡的趋势,其最高降解率可达54.7%,并存在高氯代PCBs向低氯代PCBs的转化过程.     

一株产絮凝剂的类芽孢杆菌新种及絮凝特性研究

从新疆荒漠地区分离到一株产高效絮凝剂的菌株Y24-1,根据菌株的形态学特征和16S rRNA基因序列比对分析,确定该菌株为类芽孢杆菌属(Paenibacillus)新种。该菌絮凝产物的发酵动力学表明,其属于I型发酵,即菌体生长和产物合成偶联;在发酵42 h时絮凝活性最高,可达82.7%。絮凝特性研究表明,絮凝产物具有较好的热稳定性,最适絮凝pH为6.0,Ca2+、Mg2+等二价金属阳离子具有明显的助凝效果。该菌发酵产物能有效的去除多种重金属离子和色素,特别是对Pb2+和Hg2+的吸附率分别可达到90.5%和78.7%,显示了其在环境工程中良好的应用前景。     

壬基酚对一株铜绿假单胞菌吸附镉的影响

考察壬基酚（NP）对一株从重金属污染场地筛选出的铜绿假单胞菌X吸附镉（Cd）的影响,在NP浓度分别为0、1.0、10.0mg/L条件下,通过优化吸附条件,研究X菌的Cd²⁺吸附效果.结果表明,NP与Cd²⁺共存时,在Cd²⁺初始浓度为1.0mg/L的溶液中,菌体的最佳投菌量和pH值为1.0g/L和7.0,吸附2h,吸附率可达90.0%左右.失活菌与活菌的吸附结果表明失活菌的吸附能力较活菌强.NP浓度对吸附的影响结果表明,低浓度NP对菌株吸附Cd²⁺的抑制作用较小,高浓度NP时抑制作用较大.通过分析X菌处理单一Cd²⁺及Cd²⁺-NP复合污染后的红外光谱图可知,菌体表面的羟基O-H键、酰胺C-N键和N-H键和氨基均参与吸附反应,并且高浓度NP对菌体表面基团活性影响较大,从而影响其对Cd²⁺的吸附.     

金属离子对蒽、菲、芘生物降解过程的影响

对驯化筛选的多环芳烃(PAHs)高效降解菌CN4与CN2进行了深入研究,澄清了金属离子对其降解多环芳烃的作用,得出结论:对于CN2、CN4降解菌,Mn2+与常量Ca2+、Mg2+同时存在于降解体系中时,对蒽和菲降解起到明显促进作用。Cu2+和常量元素Ca2+、Mg2+混合对菲降解也起到促进作用,但没有Mn2+的促进作用明显。不加任何常量和微量金属元素离子的体系对蒽、菲、芘的降解作用仅次于含Mn2+的降解体系,加入Cu2+、Ca2+、Mg2+、Fe3+、Zn2+对CN2降解蒽、芘产生抑制作用,加入Ca2+、Mg2+、Fe2+、Zn2+对CN2降解菲产生促进作用。Mn2+主要是在降解过程中发挥作用的,外加不同浓度的Mn2+制备的菌悬液,对芘的降解作用基本没有差别。在制备菌悬液时加入Mn2+,菌体对Mn2+有富集作用,但Mn2+的存在与否并不影响菌体的生长繁殖状况。降解体系中加入Mn2+能够有效促进降解过程的进行,加入0.5 mmol/L的Mn2+对CN4菌株降解芘的促进作用最大,而在降解体系中一次性加入5.0 mmol/L的Mn2+则会对降解产生抑制作用。     

一株海洋假单胞菌产生物絮凝剂去除赤潮生物的实验研究

利用一株假单胞菌(Pseudomonas sp.)的发酵液研究了该细菌产絮凝剂对东海原甲藻和裸甲藻的絮凝去除作用.结果表明,该生物絮凝剂可有效絮凝去除实验所选用两种赤潮生物,并且随絮凝剂用量的增加以及作用时间的延长,去除效果逐渐增加至最大然后基本保持恒定.有效絮凝去除赤潮生物的体积浓度为4.0%～10.0%.有效絮凝作用时间为1.5 h左右,絮凝效率与体系的pH值密切相关,pH在8.0左右絮凝效率较高.不同浓度的Ca2+、Mg2+对该絮凝剂絮凝除藻作用有一定的增效作用, Ca2+、Mg2+的最佳助凝离子浓度分别为2.0 mmol/L及4.0 mmol/L.     

Sphaerotilus natans对Zn~(2+)吸附的研究

以球衣菌作为生物吸附剂,研究了球衣菌对Zn2+吸附过程中的影响因素,包括吸附时间,pH,菌龄等。结果表明:Zn2+浓度为1.0mg/L,菌体浓度为0.5g/L,菌龄32h,pH7.0,吸附时间30min时,吸附的效果最好,吸附率达到77.2%,吸附量为3.86mg/g。吸附作用是一个快速的过程,30min就基本达到平衡。     

高效耐镍寡养单胞菌的分离鉴定及除Ni~(2+)特性研究

从含镍污水中筛选出一株高耐受Ni2+的菌株,并对该菌株进行了16S rDNA鉴定。同时,以该菌株作为生物吸附剂去除水中低浓度的Ni2+,考察了菌体投加量、pH、镍初始浓度、吸附时间和温度等因素对菌株去除Ni2+的影响。结果表明:经16S rDNA鉴定,筛选得到的高耐受Ni2+的菌株为一株寡养单胞菌属(Stenotrophomonas sp.)的菌株,该菌株对Ni2+表现出良好的吸附性能,在pH为6.0~8.0,温度为25~40℃的范围内,质量浓度为1.5 g/L菌体吸附10 mg/L的Ni2+120 min后,去除率均达90%以上。动力学和等温吸附分析表明,整个吸附过程更符合准二级动力学模型(R2=0.999 9),Langmuir模型相比Freundlich模型而言,有着较好的拟合效果,揭示菌株对Ni2+的吸附以单分子层吸附为主,并且分离因子RL值均在0~1之间,说明Ni2+在菌株上的吸附为有利吸附。     

一株降解微囊藻毒素菌种的鉴定及其活性研究

从巢湖水体中分离出一株能够降解微囊藻毒素(MCs)的菌株M9,通过生理生化实验以及16S rDNA序列比对和序列分析,表明该菌株16S rDNA的全序列与吉氏库特菌kurthia gibsonii的相似性达99%.研究了pH值、外加碳源、氮源以及金属离子对菌株M9降解MCs活性的效应,发现菌株M9降解MCs的最适pH值为7.0.乙醇可显著提高MCs的降解活性,在48h内对微囊藻毒素RR(MC-RR)和微囊藻毒素LR(MC-LR)的降解率分别达到70.0%和81.4%.以硫酸铵为氮源时该菌株对MC-RR和MC-LR的降解率最高,分别为70.4%和80.9%.金属离子Cu2+、Zn2+和Mn2+对菌株M9降解MCs有明显的促进作用,48h时MC-RR和MC-LR的降解率分别达到了85%和93%以上;而Fe3+和Mg2+对降解过程的促进作用不如Cu2+、Zn2+和Mn2+.     

铜绿假单胞菌对铜和铅的吸附

研究了铜绿假单胞菌(Pseudomonas aeruginosa)对Cu和Pb的吸附特性.结果表明,相同条件下,该菌株对Cu~(2+)的吸附率低于Pb~(2+).对于单一重金属体系,吸附率均随时间的延长先上升后平稳变化,2 h达到稳定.吸附率随投菌量的增加先迅速增加,之后趋于平稳.对于Cu~(2+),投菌量为1 g·L~(-1)时吸附率达到稳定,而Pb~(2+)的吸附效果达到平稳时的投菌量为0.5 g·L~(-1).单位质量菌体对Cu~(2+)、Pb~(2+)的吸附量随投菌量的增加而下降.pH为3时,菌体的吸附效果较差,当pH为5~8时,2种重金属的吸附效果较高.对于活菌,Pb~(2+)对菌体吸附Cu~(2+)有抑制作用,而Cu~(2+)对菌体吸附Pb~(2+)的影响无明显规律.对于失活菌,P.aeruginosa吸附Pb~(2+)和Cu~(2+)的效果均随共存重金属浓度的增大而降低,但Cu~(2+)对Pb~(2+)的影响比Pb~(2+)对Cu~(2+)的影响更显著.扫描电镜观察发现,吸附后的菌体较吸附前聚集性更好.总体而言,P.aeruginosa能对水体中共存的Cu~(2+)和Pb~(2+)有较好的吸附效果.     

金属离子对三苯基锡酶促降解的影响

研究了不同金属离子及其添加形式对肺炎克雷伯氏菌胞内酶和胞外酶降解三苯基锡的影响,以期为阐明有机锡的酶促降解机制提供实验依据.结果表明,菌体对K+、Mg2+、Cu2+、Ca2+、Fe3+具有良好的耐受能力,高浓度的Zn2+、Fe2+可能对菌体产生一定的毒害作用,从而影响其生长.适当浓度范围的K+、Mg2+、Zn2+、Cu...     

芽孢杆菌生物吸附处理含铜废水研究

用芽孢杆菌干菌体生物吸附去除废水中的铜离子,试验了pH、接触时间、初始铜离子浓度对该芽孢杆菌生物吸附铜的影响,结果表明:在温度为25℃、pH值5.0、初始铜离子浓度200mg/L、吸附时间不超过30min有最大吸附量16.27mg/g;此时去除率为16.27%,且25℃吸附平衡符合Langmuir等温模型与Freundlich等温模型;因此用芽孢杆菌生物吸附处理低浓度含铜废水可行、经济。     

融合菌-活性污泥联合曝气吸附处理重金属铬

研究了融合菌RHJ-004与活性污泥联合曝气处理含铬废水的生物吸附性能。结果表明,融合菌RHJ-004与活性污泥联合曝气对铬具有良好的处理效果,投加10g/L菌体、6g/L污泥,处理50mg/L的铬液,还原率可达83.26%,去除率达72.04%。该吸附剂对处理酸性含铬废水具有很大的潜力,在pH=1￣5时,还原率均>80%,去除率均>70%;溶解氧是影响该吸附过程的一个重要参数,当DO=2￣4mg/L时,生物吸附效果较好,还原率达到75%以上,去除率也超过65%;融合菌RHJ-004与活性污泥对六价铬的联合吸附可用Langmuir模型和Freundlich模型描述,但Freundlich模型的拟合效果更好。     

黄曲霉A5p1对偶氮染料的降解特性和降解途径

以黄曲霉菌株A5p1为生物材料,研究其脱色染料的广谱性,并选择偶氮染料直接蓝71（DB71）为模型底物,探讨脱色特性及降解产物.该菌株对15种染料的脱色测试结果表明,染料浓度为100mg/L时脱色效率为61.7%~100%.该菌对偶氮染料DB71具有生物吸附和生物降解的双重作用,在pH值7.0,温度30℃,染料浓度300mg/L,蔗糖为碳源时对DB71 脱色率为100%.酶分析显示葡萄糖氧化酶和锰过氧化物酶参与染料的降解.FTIR、GC-MS和LC-MS分析确定代谢终产物为萘胺、叠氮萘、2-羟基-6-草酰-苯甲酸和1-萘酚.     

微生物吸附剂对重金属的吸附特性

从活性污泥中分离得到5株菌,检验了它们对重金属离子的吸附能力,其中类产碱假单胞菌(Pseudomonas pseudoalcaligenes)和藤黄微球菌(Micrococcus luteus)GC subgroup B对Cu(Ⅱ)和Pb(Ⅱ)离子吸附能力最强.考察了Cu(Ⅱ)和Pb(Ⅱ)离子分别在这2种菌体上的吸附特性研究表明,Langmuir型吸附模式能很好地描述Cu(Ⅱ)和Pb(Ⅱ)离子在这2种菌体上的吸附实验数据,其线形回归系数高达0.99,溶液pH值是影响吸附的最主要因素,pH=5～6是吸附Cu(Ⅱ)和Pb(Ⅱ)离子的适宜条件.吸附动力学实验研究表明,菌体对Cu(Ⅱ)和Pb(Ⅱ)离子的吸附可以分为迅速的细胞表面结合和缓慢的向细胞内的传输,稀HNO₃和H₂SO₄是Cu(Ⅱ)离子从Micrococcus luteus GC subgroup B菌体上有效的洗脱剂.     

Removal of sulfamethazine antibiotics by aerobic sludge and an isolated Achromobacter sp. S-3

Removal characteristics of sulfamethazine (SMZ) by sludge and a bacterial strain using an aerobic sequence batch reactor (ASBR) were studied. Operating conditions were optimized by varying the reaction time and sludge retention time (SRT). An Achromobacter sp. (S-3) with the ability to remove SMZ was isolated from the ASBR. The effects of different operating parameters (pH and temperature) on the biodegradation of SMZ by S-3 were determined. The results indicate that, between 0.5 and 4 hr, reaction time of the ASBR had a significant effect on the SMZ removal efficiency in the system. The SMZ removal efficiency also increased from 45% to 80% when SRT was prolonged from 5 to 25 days, although longer SRT had no impact on SMZ removal. The SMZ adsorption rate decreased with increasing temperature, which fitted Freundlich isotherm well. The removal of SMZ in the ASBR was due to the combined effects of adsorption and degradation, and degradation played a leading role.     

Biosorption of lead by Phanerochaete chrysosporium in the form of pellets

The growth of Phanerochaete chrysosporium(ATCC 24725) in pellets was influenced by culture time,medium pH,C/N,surfactant concentration,spore number in inoculum,and shaking rate.The removal of Pb^2 from aqueous solution by this kind of mycelial pellets was studied.The results indicated that many factors affected biosorption.These factors included pH,Pb^2 concentration,co-ion,adsorption time, and chemical pretreatments of biomass.Under optimum biosorption conditions(pH4.5,27℃,16h),the highest lead uptake of 108 mg/g,was observed with mycelial pellets of 1.5-1.7 mm in diameter which were treated with 0.1 mol/L NaOH solution before adsorption.Pretreatment of biomass with NaOH further increased its biosorption capacity.     

板栗内皮对水溶液中镉的吸附研究

采用生物吸附法去除水体重金属污染具有重要的现实意义.本文以板栗内皮为吸附剂,研究了溶液pH值、反应时间、吸附剂投加量对水溶液中镉的吸附量与去除率的影响;通过模型拟合、离子交换实验、电镜扫描（SEM）和红外光谱（FTIR）分析,对吸附机理进行了探讨.结果表明：板栗内皮是一种理想的镉吸附剂,适应pH值范围宽（3～6）,达到...     

Biosorption of cesium（Ⅰ） from aqueous solution by a novel exopolymers secreted from Pseudomonas fluorescens C-2： Equilibrium and kinetic studies

The biosorption characteristics of Cs(I) ions from aqueous solution using exopolymers (PFC02) produced from Pseudomonas fluorescens C-2 were investigated as a function of pH, biosorbent dosage, contact time and initial concentration. pH played a major role in the adsorption process, and the optimum pH for the removal of Cs(I) was 8.0. Langmuir, Freundlich and Dubinin-Radushkevich (D-R) models were applied to describe the biosorption isotherm of the Cs(I) ions by PFC02. The Lagergren first-order, pseudo second-order kinetic and intraparticle diffusion models were used to test the kinetic data. Langmuir model and D-R model fitted the equilibrium data better than the Freundlich isotherm. The monolayer adsorption capacities of PFC02 as obtained from Langmuir isotherm at 25°C was found to be 32.63 mg/g. From the D-R isotherm model, the mean free energy was calculated as 26.73 kJ/mol, indicating that the biosorption of cesium was chemisorption. The biosorption process was rapid, and the kinetic rates were best fitted to the pseudo second-order model, which indicated the biosorption process operated through chemisorption mechanism. FT-IR analysis of PFC02 showed the possible functional groups responsible for cesium adsorption were hydroxyl, carboxyl, carbonyl and sulphonate groups. SEM analysis showed the porous structure of the material while EDX analysis confirmed the adsorption of Cs(I) on PFC02. Cesium adsorbed onto the PFC02 could be desorbed efficiently using 1 mol/L HNO3, and the enrichment factor was 50.0. Furthermore, PFC02 could be reused five times with only about 8.25% regeneration loss. The developed method was successfully utilized for the removal of Cs(I) ions from aqueous solution.     

Biosorption of cadmium(Ⅱ) and lead(Ⅱ) ions from aqueous solutions onto dried activated sludge

The removal of heavy-metal ions from aqueous solutions by using dried activated sludge has been investigated in batch systems. Effect of solution pH, initial metal ion concentration, and temperature were determined. The results of the kinetic studies showed that the uptake processes of the two metal ions（Cd（Ⅱ） and Pb（Ⅱ）） followed the pseudo-second-order rate expression. The equilibrium data fitted very well to both the Langmuir and Freundlich adsorption models. The FT-IR analysis showed that the main mechanism of Cd（Ⅱ） and Pb（Ⅱ） biosorption onto dried activated sludge was their binding with amide I group.