Friction measurements on “anti-slip” floors under shoe sole,contamination, and inclination conditions

Friction measurements were conducted to study the effects of shoe sole, floor, contamination, and inclined angle of the floor surface on friction coefficient. The shoe sole samples included composite rubber outsole samples with and without V-shaped tread design. Unglazed ceramic tiles of both flat and tiles with molded profile design were tested. The contamination conditions included dry, wet, and glycerol-contaminated conditions. The inclined angles included 0°, 5°, and 10°. A Brungraber Mark II slipmeter was used. The results showed that all the four factors affected friction coefficient significantly (p < 0.0001). Flat rubber soles had higher friction coefficients than the soling samples with V-shaped tread design on all tested floors and inclined angles under wet conditions. Flat soles, however, had extremely low friction when tested on flat floors under glycerol-contaminated conditions. The floors with molded grooves perpendicular to friction measurement direction had the highest friction coefficients than all other floor conditions under both the wet and glycerol-contaminated conditions except the wet/flat sole/10° condition. A regression model with a cosine function was established to describe the relationship between friction coefficient and inclined angle of the floor under the experimental conditions. This model is statistically significant at p < 0.0001 with an R² of 0.97.     

Friction measurements on three commonly used floors on a college campus under dry,wet, and sand-covered conditions

Slipping and falling are common incidents not only in workplaces but also on school campuses. In this research, we measured the coefficient of fiction of three floors commonly used on a college campus in Taiwan, under dry, wet, and sand-covered conditions using the Brungraber Mark II slipmeter. Leather, rubber, and polyvinyl chloride footwear samples without tread pattern were adopted in the friction measurement. The most surprising finding of this study was that there were significant friction reductions when the floors (terrazzo, ceramic and quarry) were covered by sand as compared with both dry and wet conditions. The grains of sand on the floor resulted in a friction loss ranging from 71% to 92% as compared with the dry non-contaminated surface, depending on the type of the footwear material and floor. The results indicated that effects of sand particles on the friction at footwear–floor interface were more significant than that of the wet conditions for most of the footwear material–floor combinations tested in this experiment.     

A field assessment of floor slipperiness in a fish market in Taiwan

A field assessment of floor slipperiness in 10 fish stands in a fish market in Taiwan was conducted using both friction measurements and subjective ratings. The friction measurements were conducted using the Portable Skid Resistance Tester (PSRT). The subjective ratings of floor slipperiness of both the workers and the customers were collected. The friction measurement results showed that the sink areas had both the lowest friction values and subjective ratings. The overall friction measurement results and the subjective ratings were in fair agreement (r = 0.46 and ρ = 0.49). The customers perceived the walkways as somewhere between “very slippery” to “somewhat slippery” and the picking-up areas as “very slippery.” These were different from the perceptions of the workers where they perceived both areas as “somewhat slippery.”     

Performance of slippery and slip-resistant footwear in different wintry weather conditions measured in situ

In Finland about 70,000 people are annually injured in pedestrian and bicycle falling accidents occurred at the street, walkways and courtyards. Around 2/3 of these occur when the walking surface is covered by ice or snow. In general, slipping is caused by both environmental and human factors. The primary environmental factor behind slipping accidents is slip resistance characteristics of underfoot surface. Especially in winter slipping accidents are mainly due to inadequate friction between footwear and underfoot surfaces. Portable devices measuring friction, i.e. slipmeters, may be used for assessing slipperiness on different walking surfaces in situ. During winter seasons 2003 and 2004 a study was performed to evaluate the usability of portable slip simulator for measuring slipperiness of walkways on varying weather conditions and to assess slip resistance of different footwear. The Portable Slip Simulator proved to be applicable for measuring in situ the slipperiness of wintry walking surfaces and evaluating quality of winter maintenance. Significant differences in traction between footwear were found especially in normal Finnish climate winter days when friction provided by slip-resistant footwear was multifold compared to a poorer one. On very slippery icy surfaces no footwear provided enough grip and, therefore, in such conditions anti-slip devices should be used.     

The Surface Roughness of a Rubber Soling Material Determines the Coefficient of Friction on Water-Lubricated Surfaces

For more than a decade, evidence has been accumulating that points to the fact that the microscopic roughness of the footwear soling surface is a major determinant of slip-resistance on lubricated surfaces, but conclusive experimental proof has been lacking. This article describes an experiment in which five pairs of shoes were soled with the same rubber compound. Four of the pairs were abraded by different grades of grit to produce a range of roughness values. The coefficient of friction (CoF) of the five solings was then measured repeatedly by the walking traction method on wet surfaces including glazed wall tiles, vinyl asbestos coated with the wax floor polish, and both sides of a sheet of float glass. The Kruskal-Wallis statistical test proved beyond doubt that the soling roughness is a major factor in determining the CoF of this rubber soling material; p < 10⁻⁵. Nearly all of the grip was due to surface roughness of the soling material on these atypically smooth floors, although the surface roughness of the floors also had a significant effect on CoF; p < 0.003. Float glass is shown to be a promising reference floor material for the measurement of CoF of footwear; there was no statistical difference between results for the two sides of the glass sheet. Float glass could be used in the development of a standard CoF test method because new sheets of glass from the same manufacturer are identical and extremely smooth. The specification of CoF values for solings/floors combinations in lubricated conditions is of little value unless associated with roughness measurements and knowledge of how wear will affect the surface roughness of the sole. This article reports the first evidence that any specification of flooring by measuring CoF based on dry surfaces could lead to an increase in the number of injuries caused by slipping on the wet surfaces. Published by Elsevier Science Ltd     

Heel contact dynamics during slip events on level and inclined surfaces

This study describes heel contact dynamics during slip events, information that must be known to develop biomechanically relevant shoe-floor coefficient of friction measurement systems. Sixteen subjects walked on a level, 5 and 10° ramp with two possible contaminants (dry, oil). Foot motion was recorded at 350 Hz and compared among no-slip, slip-recovery and slip-fall events. For all trials, the foot rotated to foot-flat, even during slip and fall trials. Heel sliding patterns recorded upon and shortly after heel contact were similar for all conditions. Slip distances, sliding velocities and heel acceleration profiles varied across trials. During the fall trials, the slipping motion of the foot was found to decelerate approximately 200 to 300 ms into stance before accelerating again, eventually leading to the fall. This deceleration was believed to be an attempt by the subject to recover from the slip. Recovery attempts on inclined surfaces were less successful than on level floors. In general, the slip distance and peak forward sliding velocity associated with fall trials were greater than or equal to 10 cm and 0.8 m/s, respectively. These complex motions at the shoe-floor interface during slipping should be taken into account for improving slip resistance measurement systems.     

Evaluation of two models of a slipmeter

The aim of the study was to compare the performances of the Brungraber Mark II (BM II) and Mark III (BM III) slipmeters. Friction measurements with the two slipmeters were conducted in a laboratory using four footwear materials, four floor types, and three surface conditions. Both the coefficient of friction (COF) values obtained with the slipmeters and the force platform-based COF values were measured. The COF measured with the BM II was slightly higher than that measured with the BM III with a R² of 0.83. A comparison of the averaged normal force between the two slipmeters showed that the BM II generated a significantly higher normal force than the BM III at a low COF and the difference of the normal force between the two slipmeters decreased when the COF value was increased. The regression analysis results in this study showed that the force platform-based COF values were closer to the COF values obtained with the BM III than with the BM II. The R² values for the regression model between the COF values obtained from the slipmeter and the force platform were 0.90 and 0.79 for the BM II and BM III, respectively.     

Preferred surface microscopic geometric features on floors as potential interventions for slip and fall accidents on liquid contaminated surfaces

PROBLEM: Surface roughness affects friction, so selection of floor surfaces with certain roughness characteristics could potentially reduce slip and fall accidents. This article summarizes the preferred surface microscopic geometric features that could increase friction on surfaces covered with liquid contaminants. METHOD: Three types of surface features, represented by the average of the maximum height above the mean line in each cut-off length (R(pm)), the arithmetical average of surface slope (Delta(a)), and the kernel roughness depth (R(k)), are identified as preferred surface microscopic geometric features for a higher friction. The proper settings on the profilometers (instruments used to measure surface roughness) for optimizing these surface parameters are specified. The friction mechanisms involved reveal why these features are more desirable. RESULTS: Although surface roughness is important in determining slipperiness, there is still insufficient information to establish a safety criterion based on roughness; however, the method presented in this paper can readily provide a relative comparison. IMPACT ON INDUSTRY: The summary presented will help safety professionals properly select new floor surfaces or assess existing floors to reduce slip and fall accidents.     

Subjective assessments of floor slipperiness before and after walk under two lighting conditions

A gait experiment was performed. The participants were tested under shoes, floors, surface and lighting conditions. They gave floor slipperiness ratings before and after a gait trial. The perceived sense of slip (PSOS) was collected. It was found that the perceived floor slipperiness (PFS) before walking was affected significantly by the lighting, floor and surface conditions. Relative low PFS values were recorded under wet and detergent-contaminated conditions in the normal daylight condition as compared with those in the dimmed condition. The PFS after the gait was significantly affected by the floor and surface conditions. The PSOS was highly correlated with the PFS after trial. The regression analyses results indicated that both the coefficient of friction (COF) of the floor and lighting were primary predictors of the PFS before a gait. The COF and walking speed were the primary predictors of the PFS after a gait.     

Postural sway following prolonged exposure to an inclined surface

Fatal and non-fatal falls from elevation have been documented to be a significant issue. Historically, roofing work has been ranked among the highest in incidents of falls. Recent literature has indicated that exposure to inclined surfaces (roof) has a detrimental effect on postural stability. The purpose of this preliminary study was to determine if postural instability was found to increase following extended exposure to an inclined surface. Twenty-three participants were pre/post tested under four postural stability conditions while varying duration exposure (0.0–2.0 h) to an inclined surface. Dependent variable postural sway measures were calculated from center of pressure data derived from a portable force plate. The results indicate significant differences between pre and post-exposure measures. Specifically, the results imply that an individual is less stable directly after performing tasks on an inclined surface. These findings contribute to the literature and serve as a basis for further research into work rest cycles for those individuals who routinely work on inclined surfaces.     

Slip Resistance of Industrial Floor Surfaces: Development of an Elastomer Suited to In-Situ Measurement

Slips contribute to 12% of occupational accidents. A slip resistant floor is a mean to prevent slipping accidents occurring in workshops. Floor slip resistance is often evaluated by measuring a friction index, proportional to the force opposing slipping of a reference elastomer on the floor surface under test. When implementing a portable appliance, slip resistance measurements carried out on lubricated floors were not stabilized. The authors advanced the hypothesis of oil impregnating the elastomer. A new elastomer suited to in-situ measurement has been developed to achieve stable measuring conditions. This study highlights the fact that the nature and characteristics of a reference elastomer must be specified when slip resistance measurements are carried out.     

Development of an objective determination of a slip with a portable inclineable articulated strut slip tester (PIAST)

A portable inclineable articulated strut slip tester (PIAST) is a slipmeter that is widely used in the USA to measure coefficient of friction (COF) at the shoe sole and floor interface. A determination of a slip at the measurement interface, which is currently judged subjectively by operators, plays a crucial role in deciding the outcomes of a PIAST measurement. The goal of this study was to develop an objective determination of a slip based on the movement of the weight used by the slipmeter. The displacement of the weight and the time duration of consecutive strikes in a measurement were used to derive the objective slip criterion. Various footwear materials, floor materials and surface conditions were used to cover a wide range of COF values. The results of the regression analysis indicated that the objective COF predicted by the method developed in the current study was significant (R² = 0.997, β = 0.991, p < 0.001) in predicting the subjective COF determined by the operator.     

Development of new footwear sole surface pattern for prevention of slip-related falls

In this study, a new rubber surface pattern for a footwear sole was developed to prevent slip-related falls. This pattern shows a high static coefficient of friction (SCOF) and a high dynamic coefficient of friction (DCOF) when sliding against a liquid contaminated surface. A hybrid rubber block, in which a rubber block with a rough surface (Ra = 30.4 μm) was sandwiched between two rubber blocks with smooth surfaces (Ra = 0.98 μm), was prepared. The ratio of the rough surface area to the whole rubber block surface area r was 0%, 30%, 50%, 80%, and 100%. The coefficient of friction of the rubber blocks was measured when sliding against a stainless steel plate with Ra of 0.09 μm contaminated with a 90% aqueous solution of glycerol. While the SCOF increased with an increase of the rough surface area ratio r, the DCOF during steady-state sliding decreased with an increase of the rough surface area ratio r. The rough surface area ratio of 50% achieved a SCOF value around 0.5 or more and a DCOF value greater than 0.5. Furthermore, the difference in the value of the SCOF and DCOF was the smallest for the rubber block with r of 50%. The results indicated that the rubber block with r of 50% would be applicable to a footwear sole surface pattern to prevent slip and fall accidents on contaminated surfaces.     

Thermal characterization of fly ash from one municipal solid waste incinerator (MSWI) in Shanghai

This study aims to develop a methodology for the thermal characterization of MSWI fly ash. We performed TGA–DTA and component variation analysis, microstructure transfer of sintered fly ash, as well as leaching toxicity, volatilization ratio and specification transformation of heavy metals as a function of temperature. It is found that content of crystal phases first increases between room temperature and 800 °C and then decreases between 800 °C and 1200 °C, while that of glass phases registers a reverse trend. Fly ash registers a SiO₂–Al₂O₃–metal oxides system and its content of glass phases is around 57%. Increase of sintering temperature between 600 °C and 1200 °C is conducive to the reduction of soluble As, Cd, Cu, Hg, Pb, Ni and Zn, while content of soluble Cr increases as temperature rises from 800 °C to 1200 °C.     

Investigation on removal of p-nitrophenol using a hybridized photo-thermal activated persulfate process: Central composite design modeling

The aim of this work is the study of p-nitrophenol (PNP) removal, as a nitroaromatic compound, using a hybridized photo-thermally activated potassium persulfate (KPS) in a fully recycled batch reactor. Response surface method was used for modeling the process. Reaction temperature, KPS initial dosage and initial pH of the solution were selected as variables, besides PNP degradation efficiency was selected as the response. ANOVA analysis reveals that a second order polynomial model with F-value of 41.7, p-value of 0.0001 and regression coefficient of 0.95 is able to predict the response. Based on the model, the process optimum conditions were introduced as initial pH of 4.5, [KPS]₀ = 1452 mg/L and T = 66 °C. Also experiments showed that using thermolysis and photolysis of the persulfate simultaneously, the role of thermolysis is not considerable. A pseudo first order kinetic model was established to describe the degradation reaction. Operational cost, as a vital industrial criterion, was estimated so that the condition of initial pH of 4.5, [KPS]₀ = 1452 mg/L and T = 25 °C showed the highest cost effective case. Under the preferred mild condition, the process will reach to 84% and 89% of degradation and mineralization efficiencies, after 60 and 120 min, respectively.     

Inherently safer reactors: Improved efficiency of 3-picoline N-oxidation in the temperature range 110–125 °C

Alkylpyridine N-oxides are important intermediates in the pharmaceutical and agrochemicals industries. The N-oxides are produced via the homogeneously catalyzed oxidation of the respective alkylpyridines using a 50% excess of hydrogen peroxide. The competitive hydrogen peroxide decomposition produces oxygen in the flammable environment of alkylpyridines and thus forms a key hazard for this reaction. In this work, the N-oxidation was performed under pressure in the temperature range of 110–125 °C with different catalyst concentrations. It was shown that temperature had an undisputable positive effect on the N-oxidation efficiency. The accurate measurement of the pressure rise due to decomposition was difficult. However, only 5% of the added H₂O₂ decomposed when stoichiometric quantities were employed, even in the temperature of 110 °C. The N-oxidation was very efficient, even when the lowest concentration of catalyst employed in this study was used.     

Dilute Acid Hydrolysis of Cellulose and Cellulosic Bio-Waste Using a Microwave Reactor System

The dilute acid hydrolysis of grass and cellulose with phosphoric acid was undertaken in a microwave reactor system. The experimental data and reaction kinetic analysis indicate that this is a potential process for cellulose and hemi-cellulose hydrolysis, due to a rapid hydrolysis reaction at moderate temperatures. The optimum conditions for grass hydrolysis were found to be 2.5% phosphoric acid at a temperature of 175°C. It was found that sugar degradation occurred at acid concentrations greater than 2.5% (v/v) and temperatures greater than 175°C. In a further series of experiments, the kinetics of dilute acid hydrolysis of cellulose was investigated varying phosphoric acid concentration and reaction temperatures. The experimental data indicate that the use of microwave technology can successfully facilitate dilute acid hydrolysis of cellulose allowing high yields of glucose in short reaction times. The optimum conditions gave a yield of 90% glucose. A pseudo-homogeneous consecutive first order reaction was assumed and the reaction rate constants were calculated as: k₁ = 0.0813 s⁻¹; k₂ = 0.0075 s⁻¹, which compare favourably with reaction rate constants found in conventional non-microwave reaction systems. The kinetic analysis would indicate that the primary advantages of employing microwave heating were to: achieve a high rate constant at moderate temperatures: and to prevent ‘hot spot’ formation within the reactor, which would have cause localised degradation of glucose.     

7 mT static magnetic exposure enhanced synthesis of poly-3-hydroxybutyrate by activated sludge at low temperature and high acetate concentration

The effect of 7 mT (milliTesla) SMF (static magnetic field) on poly-3-hydroxybutyrate (PHB) production was studied at an acetate concentration of 260 Cmmol l^?1 and temperature of 10 °C. The SMF decreased the specific acetate uptake rate by 29%, but increased the maximum PHB content and the yield of PHB on acetate by 32 and 28% respectively. The ratio q_P/(q_S ? q_P), which described specific PHB production rate over the difference between specific acetate uptake rate and specific PHB production rate, was introduced for evaluation of the ratio of carbon flux into PHB synthesis and into the TCA (tricarboxylic acid) cycle. This value reached 2.3 when activated sludge culture was exposed to magnetic field of 7 mT, which was 1.1 times higher than the q_P/(q_S ? q_P) value obtained without magnetic exposure. Therefore, the SMF promoted diversion of more acetyl-CoA towards PHB synthesis and could offset adverse effects of high acetate concentration and low temperature. These results provide evidence that SMF enhances PHB production by activated sludge.     

Decolorization of synthetic Methyl Orange wastewater by electrocoagulation with periodic reversal of electrodes and optimization by RSM

Treatment of Methyl Orange (MO), an azo dye, synthetic wastewater by electrocoagulation with periodic reversal of the electrodes (PREC) was examined. Response Surface Methodology (RSM) was used to optimize the influence of experimental conditions for color removal (CR), energy consumption (ENC), electrode consumption (ELC) and sludge production (SP) per kg MO removed (kg(MO_r)) with optimal conditions being found to be pH 7.4, solution conductivity (к) 9.4 mS cm⁻¹, cell voltage (U) 4.4 V, current density (j) 185 mA cm⁻², electrocoagulation time (T) 14 min, cycle of periodic reversal of electrodes (t) 15 s, inter-electrode distance (d) 3.5 cm and initial MO concentration of 125 mg L⁻¹. Under these conditions, 97 ± 2% color was removed and ENC, ELC and SP were 44 ± 3 kWh kg(MO_r)⁻¹, 4.1 ± 0.2 kg(Al) kg(MO_r)⁻¹ and 17.2 ± 0.9 kg(sludge) kg(MO_r)⁻¹, respectively. With the enhanced electrochemical efficiency resulting from the periodic electrode reversal, the coefficients of increased resistance and decreased current density between the two electrodes in the PREC setup were 2.48 × 10⁻⁴ Ω cm⁻² min⁻¹ and 0.29 mA cm⁻² min⁻¹, respectively, as compared to 7.72 × 10⁻⁴ Ω cm⁻² min⁻¹ and 0.79 mA cm⁻² min⁻¹ as measured for the traditional electrocoagulation process. The rate constant of decolorization was also enhanced by 20.4% from 0.152 min⁻¹ in the traditional electrocoagulation process to 0.183 min⁻¹ in the PREC process. These performance characteristics indicate that the PREC approach may be more promising in terms of practical application, as a cost-effective treatment, than conventional electrocoagulation for textile dye removals.     

Evaluation of Abelmoschus esculentus (lady's finger) seed as a novel biosorbent for the removal of Acid Blue 113 dye from aqueous solutions

The use of a new biosorbent derived from Abelmoschus esculentus (A. esculentus) seed for the removal of Acid Blue 113 (AB113) in aqueous solutions was investigated in batch mode. Biosorption studies were carried out under varying operational parameters including initial pH, biosorbent dosage, contact time, initial dye concentration and temperature. The results indicated that the biosorption properties were strongly dependent on initial pH. Fourier transform infrared spectroscopy analysis revealed that hydroxyl, carboxylic and amide functional groups present on the biosorbent surface were involved in the dye removal process. Equilibrium data were best fitted by the Langmuir model. The maximum biosorption capacity was 169.9 ± 3.1 mg g⁻¹ at 25 °C and initial pH 5.5. The kinetic data were in good agreement with the pseudo-second-order kinetic model. The process was controlled by diffusion through boundary layer at the initial stage followed by intra-particle diffusion at the later stage. Thermodynamic evaluation showed that the process was endothermic and spontaneous. The present study suggests that A. esculentus seed with maximum biosorption capacity which compared well with values reported in the literature can be a potential biosorbent for AB113 dye removal.