高浓度抗菌素废水厌氧预处理的应用实例

采用厌氧UASB反应器处理鲁抗制药的高浓度青霉素、链霉素发酵废水、溶媒废水及提炼废水是可以的.通过中温厌氧消化,当进水COD在15000mg/l左右、UASB有机负荷为5kgCOD/m3·d左右时,COD去除率为80%,出水挥发酸(VFA)小于10mmol/l.     

中空纤维膜生物反应器处理炼厂浮选池出水试验研究

研究设计的膜生物反应器处理炼厂浮选池出水,在每天进水容积负荷1.0 kg COD/m3,进水COD浓度600 mg/L,MLSS为900～5500 mg/L的条件下,无论活性污泥表现正常还是膨胀,过滤出水中COD均稳定地小于90 mg/L,处理效果好于目前炼油厂的合建式曝气池(容积负荷为0.5 kg COD/m3左右,出水COD100 mg/L左右)。试验运行期间,膜通量最高可达到42 L/m2·h。该工艺的技术关键是采用特殊流态来降低膜堵塞的膜生物反应器和优良质量的膜。     

厌氧-好氧一体化反应器处理高浓度有机废水的运行特性研究

本实验采用新型厌氧—好氧一体化反应器处理高浓度有机废水,主要研究了系统的启动与运行性能,并对系统的NH3 N去除效果作了初步考察。实验结果表明:在16℃～24℃的自然温度下,采用递增负荷、厌氧和好氧分期启动的方式,系统可在38天内达到较好的启动效果;在系统负荷运行期内,当系统总进水COD浓度平均值为3601 8mg/L,总出水COD浓度平均值为384 0mg/L,系统容积负荷平均值为2 54kgCOD/(m3·d),系统总HRT平均值为35 1h时,系统总COD去除率平均值达90 6%。实验还发现:当进水NH3 N浓度为280 3～350 7mg/L,整个系统的NH3 N去除率在68 5%～91 7%,平均为81 0%。由此说明,本反应器具有很好的COD去除性能和NH3 N去除效果,适合于处理COD浓度高且含有中等NH3 N浓度的有机废水。     

MBR/RO组合工艺回收处理己内酰胺废水的中试研究

对己内酰胺生产过程废水的回用处理工艺进行了研究。以某己内酰胺化工厂的LUCAS出水作为研究对象,采用膜生物反应器和反渗透膜处理工艺,研究此系统对己内酰胺废水的处理效果。试验结果表明,膜生物反应器工艺适用于该化工厂的生产废水,出水COD平均值为31.33mg/L,平均浊度为0.2NTU,氨氮平均值为2.81mg/L,可以满足反渗透膜的进水要求。在浓缩倍数为3时,反渗透膜系统运行稳定,且产水可以满足化工部循环冷却水用再生水水质标准。     

ABSBR处理高浓度有机废水试验研究

试验研究了ABSBR重启动的条件,讨论了影响生物降解的主要因素。试验表明：进水流量、PH值与进水COD负荷是影响废水处理效能的重要参数。进水流量维持在4L／min、pH值在6．5～7．5时有利于提高COD去除率。研究发现对于驯化成熟的ABSBR存在适宜的进水COD负荷,COD负荷在4000mg／L时,生物降解速率最快。     

SBR系统中pH与MLSS对同步硝化反硝化的影响

本文研究了SBR系统中pH值、MISS的变化对同步硝化反硝化的影响。结果表明：在进水水质和反应条件相同时，将pH值控制在8．5，出水水质最好，COD去除率达到90．0％，总氮去除率达到99．4％；在进水水质和反应条件相同，反应器中MLSS为520mg／L时，出水水质最好，COD去除率达到85馏％，总氮去除率达到99．1％。     

两相UASB反应器处理含高浓度硫酸盐黑液

两相UASB反应器处理含高浓度硫酸盐黑液,酸化相为8.87L的普通升流式反应器,甲烷相为28.75L的UASB反应器,系统温度(35±1)℃。当酸化相进水COD为(6.771～11.057)g/L,SO42-为(5.648～8.669)g/L,pH值为5.5时,整个系统COD去除率平均值为74.42%;系统对负荷的冲击有较强的耐受能力。     

微生物菌剂在酿酒废水处理中的应用研究

采用厌氧－好氧工艺,结合微生物菌剂对酿酒废水进行了处理研究。进水CODCr浓度可达到8,456.3-22,442.0mg/L,BOD55,040.0-9.557.1mg/L,pH3-4,可不调pH,采用微生物菌剂接种可启动厌氧反应器,COD有机负荷最高达到10.2gCOD/Ld,COD去除率稳定在91－95％,BOD去除率90－94％,出水pH6.6-7.1,出水CODCr在2,000mg/L以下,BOD5800mg/L以下。厌氧污泥可全部颗粒化。好氧处理系统中接种微生物菌剂,曝气10－12小时,可保证出水中CODCr在230mg/L以下,甚至直接达到国家一级排放标准。微生物菌剂的应用是取得该处理效果的关键。     

快速纤维过滤技术处理合流制溢流试验研究

采用快速纤维过滤技术在南方某污水处理厂开展合流制溢流处理的中试研究,考察该技术对溢流污染物的去除效果.结果表明,溢流进水SS浓度值常高于COD浓度值,进水混合水样的非溶解性COD浓度为混合水样COD浓度的73.08％～90.0％;滤速不超过20.83 m/h时,SS负荷去除率大于60％,中试装置的水头损失不超过1 kP...     

序批式生物膜法处理油田采油废水

采用序批式生物膜(SBBR)法处理油田采油废水。研究并开发了特殊活性污泥的培养和驯化方法。在被处理的污水中加入微生物促生剂FYS-5,可迅速培养出处理采油废水的微生物,用此种方法培养出的活性污泥的活性高,去除有毒有害物质的能力强,能够提高处理效率,保持良好的微生物生长状况。在SBBR装置进水COD容积负荷为0.5kg/(m3·d)及进水COD为500mg/L左右的条件下,经过近两个月的连续运转,COD平均去除率超过80%,出水中COD低于100mg/L,符合GB8978-1996《污水综合排放标准》的要求,经过处理的污水可以直接排放。     

Decolorization of triphenylmethane dye-bath effluent in an integrated two-stage anaerobic reactor

In the present study, decolorization of a simulated dye waste containing three different triphenylmethane (TPM) dyes--Magenta, Malachite Green and Crystal Violet, was investigated in a laboratory scale, two-stage anaerobic high-rate reactor. The effect of various parameters (influent dye concentration, hydraulic and co-substrate loading rates) on color and COD removal efficiency of the reactor has been studied. It has been shown that the influent dye concentration had little effect on overall COD and color removal efficiency. More than 99% color removal and 96% COD removal efficiency were maintained even at a dye concentration of 500 mg/l and a dye loading rate of 1000 mg/l day. However, a minimum level of glucose as supplementary carbon source is required to maintain the maximum color removal efficiency and it drops appreciably when no glucose is added to the influent. The study also showed that the acidogenic phase of the reaction plays an important role in decolorization of the TPM dyes. In addition, the two-stage anaerobic reactor was observed to have distinct advantages over the single-stage system, as the drop in color and COD removal efficiency of stage 1 are adequately compensated by stage 2 of the reactor especially under high dye loading rates accompanied by low co-substrate loading and under reduced HRTs.     

The effects of leachate recirculation with supplemental water addition on methane production and waste decomposition in a simulated tropical landfill

In order to increase methane production efficiency, leachate recirculation is applied in landfills to increase moisture content and circulate organic matter back into the landfill cell. In the case of tropical landfills, where high temperature and evaporation occurs, leachate recirculation may not be enough to maintain the moisture content, therefore supplemental water addition into the cell is an option that could help stabilize moisture levels as well as stimulate biological activity. The objectives of this study were to determine the effects of leachate recirculation and supplemental water addition on municipal solid waste decomposition and methane production in three anaerobic digestion reactors. Anaerobic digestion with leachate recirculation and supplemental water addition showed the highest performance in terms of cumulative methane production and the stabilization period time required. It produced an accumulated methane production of 54.87 l/kg dry weight of MSW at an average rate of 0.58 l/kg dry weight/d and reached the stabilization phase on day 180. The leachate recirculation reactor provided 17.04 l/kg dry weight at a rate of 0.14l/kg dry weight/d and reached the stabilization phase on day 290. The control reactor provided 9.02 l/kg dry weight at a rate of 0.10 l/kg dry weight/d, and reached the stabilization phase on day 270. Increasing the organic loading rate (OLR) after the waste had reached the stabilization phase made it possible to increase the methane content of the gas, the methane production rate, and the COD removal. Comparison of the reactors' efficiencies at maximum OLR (5 kgCOD/m(3)/d) in terms of the methane production rate showed that the reactor using leachate recirculation with supplemental water addition still gave the highest performance (1.56 l/kg dry weight/d), whereas the leachate recirculation reactor and the control reactor provided 0.69 l/kg dry weight/d and 0.43 l/kg dry weight/d, respectively. However, when considering methane composition (average 63.09%) and COD removal (average 90.60%), slight differences were found among these three reactors.     

内循环三相生物流化床处理生活污水的试验研究

对内循环三相生物流化床处理生活污水进行了试验研究,探讨了生物膜的形成和水力停留时间及曝气量对处理效果的影响。结果表明：在HRT为6h,曝气量为0.6m3/h,进水COD和NH4＋-N分别为240.2~298.7mg/L和29.1~68.9mg/L条件下,平均COD去除率为83%,NH4＋-N去除率为95.1%。     

Behavior of an aerated submerged fixed-film reactor (ASFFR) under simultaneous organic and ammonium loading

The performance of an aerated submerged fixed-film reactor (ASFFR) under simultaneous organic and ammonium loading and its effect on nitrification was studied. Organic loadings varied in the range of 1.93 to 5.29 g chemical oxygen demand (COD) m-2 d-1 and NH4-N loadings were in the range of 116 to 318 mg NH4-N m-2 d-1. Increments of loading rates were obtained both by increasing the flow rate and increasing the influent substrate in individual pilot runs. Results showed that with organic loading rates up to 3.97 g COD m-2 d-1, complete nitrification was achievable. Although high organic loading such as 5.29 g COD m-2 d-1 could cause nitrification to stop, shifting to lower organic loadings made nitrification start and set rapidly to its previous steady-state concentrations. Comparison of results showed that in the ASFFR, nitrification would be severely affected by an organic loading rate of 5.29 g COD m-2 d-1 by increasing either the flow or the influent substrate. It should be noted that the average value of dissolved oxygen was 3.4 mg L-1 with an air supply of 15 L min-1, and there was no indication of oxygen limitation. The results of this study show the flexibility of ASFFRs under changing organic loads. Furthermore, for achieving complete nitrification and optimum application of these reactors for protecting receiving water from the environmental hazards of ammonium, the maximum organic loading that would present complete nitrification should be considered.     

Influence of organic loading on an anaerobic sequencing biofilm batch reactor (ASBBR) as a function of cycle period and wastewater concentration

The effect of organic loading on the performance of a mechanically stirred anaerobic sequencing biofilm batch reactor (ASBBR) has been investigated, by varying influent concentration and cycle period. For microbial immobilization 1-cm polyurethane foam cubes were used. An agitation rate of 500 rpm and temperature of 30+/-2 degrees C were employed. Organic loading rates (OLR) of 1.5-6.0gCODl(-1)d(-1) were applied to the 6.3-l reactor treating 2.0 l synthetic wastewater in 8 and 12-h batches and at concentrations of 500-2000mgCODl(-1), making it possible to analyze the effect of these two operation variables for the same organic loading range. Microbial immobilization on inert support maintained approximately 60 gTVS in the reactor. Filtered sample organic COD removal efficiencies ranged from 73 to 88% for organic loading up to 5.4gCODl(-1)d(-1). For higher organic loading (influent concentration of 2000mgCODl(-1) and 8-h cycle) the system presented total volatile acids accumulation, which reduced organics removal efficiency down to 55%. In this way, ASBBR with immobilized biomass was shown to be efficient for organic removal at organic loading rates of up to 5.4gCODl(-1)d(-1) and to be more stable to organic loading variations for 12-h cycles. This reactor might be an alternative to intermittent systems as it possesses greater operational flexibility. It might also be an alternative to batch systems suspended with microorganisms since it eliminates both the uncertainties regarding granulation and the time necessary for biomass sedimentation, hence reducing the total cycle period.     

Relationships between anaerobic consortia and removal efficiencies in an UASB reactor degrading 2,4 dichlorophenol (DCP)

To gain more insight into the interactions between anaerobic bacteria and reactor performances (chemical oxygen demand-COD, 2,4 dichlorophenol-2,4 DCP removals, volatile fatty acid-VFA, and methane gas productions) and how they depended on operational conditions the microbial variations in the anaerobic granular sludge from an upflow anaerobic sludge blanket (UASB) reactor treating 2,4 DCP was studied. The study was composed of two parts. In the first part, the numbers of methanogens and acedogens in the anaerobic granular sludge were counted at different COD removal efficiencies. The relationships between the numbers of methanogens, the methane gas production and VFA production were investigated. The COD removal efficiencies increased to 74% from 30% while the number of total acedogens decreased to 10 from 30 cfu ml(-1). The number of total methanogens and acedogens varied between 11 x 10(3) and 10 x 10(9)MPN g(-1) and 10 and 30 cfu ml(-1) as the 2,4 DCP removal efficiencies were obtained between 60% and 99%, respectively. It was seen that, as the number of total acedogens decreased, the COD removal efficiencies increased. However, the number of total methanogens increased as the COD removal efficiencies increased. Correlations between the bacterial number and with the removal efficiencies obtained in different operational conditions were investigated. From the results presented in this paper a high correlation between the number of bacteria, COD removals, methane gas percentage, 2,4 DCP removals and VFA was observed. In the second part, methanogen bacteria in the anaerobic granular sludge were identified. Microbial observations and biochemical tests were applied to identify the anaerobic microorganisms from the anaerobic granular sludge. In the reactor treating 2,4 DCP, Methanobacterium bryantii, Methanobacterium formicicum, Methanobrevibacter smithii, Methanococcus voltae, Methanosarcina mazei, Methanosarcina acetivorans, Methanogenium bourgense and Methanospirillum hungatei were identified.     

Treatment of low-strength soluble wastewater using an anaerobic baffled reactor (ABR)

Treatment of low-strength soluble wastewater (COD approximately 500 mg/L) was studied using an eight chambered anaerobic baffled reactor (ABR). At pseudo steady-state (PSS), the average total and soluble COD values (COD(T) and COD(S)) at 8h hydraulic retention time (HRT) were found to be around 50 and 40 mg/L, respectively, while at 10h HRT average COD(T) and COD(S) values were of the order of 47 and 37 mg/L, respectively. COD and BOD (3 day, 27 degrees C) removal averaged more than 90%. Effluent conformed to Indian standards laid down for BOD (less than 30 mg/L). Reactor effluent characteristics exhibited very low values of standard deviation indicating excellent reactor stability at PSS in terms of effluent characteristics. Based on mass balance calculations, more than 60% of raw wastewater COD was estimated to be recovered as CH(4) in the gas phase. Compartment-wise profiles indicated that most of the BOD and COD got reduced in the initial compartments only. Sudden drop in pH (7.8-6.7) and formation of volatile fatty acids (VFA) (53-85 mg/L) were observed in the first compartment due to acidogenesis and acetogenesis. The pH increased and VFA concentration decreased longitudinally down the reactor. Residence time distribution (RTD) studies revealed that the flow pattern in the ABR was neither completely plug-flow nor perfectly mixed. Observations from scanning electron micrographs (SEM) suggest that distinct phase separation takes place in an ABR.     

强制性内循环快速启动IC厌氧反应器过程的研究

如何在短时间内快速启动厌氧反应器是厌氧处理工程中的关键。本文对IC厌氧反应器分别进行强制性内循环启动和常规启动实验。结果表明 ,强制性内循环启动的反应器充分利用了内循环缓冲 pH和抗冲击负荷的能力 ,创造良好的微生物生长环境 ,最终只用了 5 4天就完成整个启动 ,比常规方式启动缩短近一个月 ,是一种值得借鉴的启动方式