Decomposition of gas-phase trichloroethene by the UV/TiO2 process in the presence of ozone.

The decomposition of gas-phase trichloroethene (TCE) in air streams by direct photolysis, the UV/TiO2 and UV/O3 processes was studied. The experiments were carried out under various UV light intensities and wavelengths, ozone dosages, and initial concentrations of TCE to investigate and compare the removal efficiency of the pollutant. For UV/TiO2 process, the individual contribution to the decomposition of TCE by direct photolysis and hydroxyl radicals destruction was differentiated to discuss the quantum efficiency with 254 and 365 nm UV lamps. The removal of gaseous TCE was found to reduce by UV/TiO2 process in the presence of ozone possibly because of the ozone molecules could scavenge hydroxyl radicals produced from the excitation of TiO2 by UV radiation to inhibit the decomposition of TCE. A photoreactor design equation for the decomposition of gaseous TCE by the UV/TiO2 process in air streams was developed by combining the continuity equation of the pollutant and the surface catalysis reaction rate expression. By the proposed design scheme, the temporal distribution of TCE at various operation conditions by the UV/TiO2 process can be well modeled.     

The direct photolysis and photocatalytic degradation of alachlor at different TiO2 and UV sources

Direct photolysis and photocatalytic degradations of alachlor, a widely used herbicide, were studied using three different monochromatic UV lamps (254, 300 and 350 nm) and two TiO(2) sources. Both the direct photolysis and photocatalytic degradations of alachlor follow pseudo-first-order decay kinetics. TiO(2)-P25 was found to be an effective photocatalyst compared to TiO(2)-BDH. The direct photolysis of alachlor was dominant at 254 nm even if TiO(2) was present in the solution. Among the three UV wavelengths used, the highest photocatalysis quantum yield was obtained at 300 nm. The photocatalytic degradation rate of alachlor increased with the dosages of TiO(2), but an overdose of TiO(2) would retard the reaction due to light attenuation. Photocatalytic reactions were slightly enhanced in an alkaline medium, and the different proton sources causing various degrees of rate retardation were due to the presence of the corresponding counter anions. This effect was diminished at a later stage after the reaction intermediates were formed.     

利用UVC去除低浓度苯的实验研究

探讨了不同实验参数对苯的UVC去除效果的影响,获得了苯的去除率与苯的初始浓度、气体流量、相对湿度和氧气含量等参数之间的关系。数据表明,在实验条件范围内,苯的去除率的倒数与苯初始浓度、气体流量之间为线性关系;苯的去除率随相对湿度的增加呈现先升高后缓慢降低的关系,最佳相对湿度值在30%～50%之间;苯的去除率随氧气量的增加而缓慢增加;波长为185+254 nm的UV与254 nm的UV相比净化效果更为理想。还分析了苯降解产生的中间产物,探讨了苯的降解机理。     

The degradation of endocrine disruptor di-n-butyl phthalate by UV irradiation: a photolysis and product study

The direct photolysis of an important endocrine disruptor compound, di-n-butyl phthalate (DBP), has been investigated under monochromatic UV irradiation at 254 nm over a wide pH range (3-11). The investigation was carried out under idealized conditions and has considered both reaction kinetics and the degradation mechanism. It was found that more than 90% of DBP can be degraded within an hour of irradiation in water. A simple model has been developed and used to predict the initial DBP photolysis rate constant at different pH values and initial DBP concentrations. The major decomposition mechanism of DBP is believed to involve the hydrolytic photolysis of the carbon in the alpha and/or beta-position of the ester chain with the production of aromatic carboxylic derivatives. Additionally, multi-degradation pathways are proposed for acid-catalyzed hydrolytic photolysis (pH 3-5), which was found to be useful in explaining the photo-degradation of DBP under acidic conditions. The use of 254 nm UV to photo-degrade DBP was found to be a relatively fast and clean process, especially in neutral to basic conditions.     

Phototransformation of ibuprofen and ketoprofen in aqueous solutions

The UV (254 nm) and UV/VUV (254/185 nm) photolysis of two anti-inflammatory drugs, ibuprofen and ketoprofen, have been studied in aqueous solutions as a possible process for the removal of non-biodegradable compounds.We have examined the effects of dissolved oxygen and initial target concentration. Upon irradiation at 254 nm, the decomposition rate of ketoprofen is almost forty times higher as it of ibuprofen whilst VUV irradiation only increased the ibuprofen decomposition rate. The presence of dissolved oxygen accelerated the photodegradation of ibuprofen, whereas no effect was observed on the degradation of ketoprofen. The maximum quantum yield for the phototransformation was 0.2. The rate of mineralization in both cases was ∼60%, even after 1 h of treatment and this suggests the formation of stable by-products which were identified using GC-MS and HPLC-MS, respectively.     

Photoassisted and photocatalytic degradation of sulfur mustard using TiO2 nanoparticles and polyoxometalates

The decomposition of highly toxic chemical warfare agent, sulfur mustard (bis(2-chloroethyl) sulfide or HD), has been studied by homogeneous photolysis and heterogeneous photocatalytic degradation on titania nanoparticles. Direct photolysis degradation of HD with irradiation system was investigated. The photocatalytic degradation of HD was investigated in the presence of TiO₂ nanoparticles and polyoxometalates embedded in titania nanoparticles in liquid phase at room temperature (33?±?2 °C). Degradation products during the treatment were identified by gas chromatography–mass spectrometry. Whereas apparent first-order kinetics of ultraviolet (UV) photolysis were slow (0.0091 min^?1), the highest degradation rate is obtained in the presence of TiO₂ nanoparticles as nanophotocatalyst. Simultaneous photolysis and photocatalysis under the full UV radiation leads to HD complete destruction in 3 h. No degradation products observed in the presence of nanophotocatalyst without irradiation in 3 h. It was found that up to 90 % of agent was decomposed under of UV irradiation without TiO₂, in 6 h. The decontamination mechanisms are often quite complex and multiple mechanisms can be operable such as hydrolysis, oxidation, and elimination. By simultaneously carrying out photolysis and photocatalysis in hexane, we have succeeded in achieving faster HD decontamination after 90 min with low catalyst loading. TiO₂ nanoparticles proved to be a superior photocatalyst under UV irradiation for HD decontamination.     

紫外光(UV)光解油田采出水中多环芳烃

为了探讨紫外光光解人工模拟油田采出水中多环芳烃的降解效率,利用自制反应装置对油田采出水中多环芳烃(PAHs)的紫外光光解做了一个初步研究。研究结果证明,紫外光光解对油田采出水中的多环芳烃萘和芴有显著的降解能力。实验室的测试表明,与紫外UVA(365 nm)、UVB(308 nm)的光照相比,紫外UVC(254 nm)在光照60 min的条件下,2种多环芳烃各自的去除率都近似达到了99%。可见,在光解效力和暴露时间两方面,紫外UVC对采出水中萘和芴的去除具有相对稳定和比较高的效率。     

An investigation into reservoir NOM reduction by UV photolysis and advanced oxidation processes

A comparison of four treatment technologies for reduction of natural organic matter (NOM) in a reservoir water was made. The work presented here is a laboratory based evaluation of NOM treatment by UV-C photolysis, UV/H(2)O(2), Fenton's reagent (FR) and photo-Fenton's reagent (PFR). The work investigated ways of reducing the organic load on water treatment works (WTWs) with a view to treating 'in-reservoir' or 'in-pipe' before the water reaches the WTW. The efficiency of each process in terms of NOM removal was determined by measuring UV absorbance at 254 nm (UV(254)) and dissolved organic carbon (DOC). In terms of DOC reduction PFR was the most effective (88% removal after 1 min) however there were interferences when measuring UV(254) which was reduced to a lesser extent (31% after 1 min). In the literature, pH 3 is reported to be the optimal pH for oxidation with FR but here the reduction of UV(254) and DOC was found to be insensitive to pH in the range 3-7. The treatment that was identified as the most effective in terms of NOM reduction and cost effectiveness was PFR.     

Study on particulates and volatile organic compounds removal with TiO2 nonwoven filter prepared by electrospinning

In this study, polyvinyl alcohol (PVA) and titania (TiO₂) Degussa P-25 were mixed to generate TiO₂ nonwoven filters using electrospinning. The wires of titanium dioxide and the nonwoven binding titania nanofibers were formed using 14 kV voltage and a distance of 15 cm. A single-factor experimental method was used to investigate the effects of parameters such as initial concentration, retention time, and light source on acetone removal by nonwoven binding titania nanofibers. Furthermore, the effects of parameters such as gas pressure, particle size, initial concentration, and retention time on the removal of particulates were also assessed. The results showed that the degradation efficiency increased with decreasing initial concentrations and increasing retention time. The best operational conditions during this study for the removal of acetone using the TiO₂ nonwoven filters were a retention time of 100 sec, initial acetone concentration of 250 ppm, and ultraviolet (UV) light source of 254 nm. Under those conditions, 99% acetone removal efficiency was obtained. In addition, 90% particulate matter removal efficiency was reached when the particulate size was greater than 200 nm and the reaction time was longer than 5 minutes. The prepared TiO₂/nanofiber has good performance for volatile organic compounds (VOCs) and particulate removal at the same time.

Implications: In this study, polyvinyl alcohol (PVA) and titania (TiO₂) Degussa P-25 were mixed to generate TiO₂ nonwoven filters using electrospinning. The results showed that the optimum operating conditions for the removal of acetone using the TiO₂ nonwoven filters were a retention time of 100 sec, initial acetone concentration of 250 ppm, and UV light source of 254 nm. Under those conditions, 99% acetone removal efficiency was obtained.     

Kinetics of simazine advanced oxidation in water

Comparison of the effects and kinetics of UV photolysis and four advanced oxidation systems (ozone, ozone/hydrogen peroxide, ozone/UV radiation and UV radiation/hydrogen peroxide) for the removal of simazine from water has been investigated. At the conditions applied, the order of reactivity was ozone < ozone/hydrogen peroxide < UV radiation < ozone/UV radiation and UV radiation/hydrogen peroxide. Rate constants of the reactions between ozone and simazine and hydroxyl radical and simazine were found to be 8.7 M-1s-1 and 2.1 x 10(9) M-1s-1, respectively. Also, a quantum yield of 0.06 mol.photon-1 was found for simazine at 254 nm UV radiation. The high value of the quantum yield corroborated the importance of the direct photolysis process. Percentage contributions of direct reaction with ozone, reaction with hydroxyl radicals and direct photolysis were also quantified.     

UV/ozone degradation of gaseous hexamethyldisilazane (HMDS)

As a carcinogen, hexamethyldisilazane (HMDS) is extensively adopted in life science microscopy, materials science and nanotechnology. However, no appropriate technology has been devised for treating HMDS in gas streams. This investigation evaluated the feasibility and effectiveness of the UV (185+254nm) and UV (254nm)/O(3) processes for degradation of gaseous HMDS. Tests were performed in two batch reactors with initial HMDS concentrations of 32-41mgm(-3) under various initial ozone dosages (O(3) (mg)/HMDS (mg)=1-5), atmospheres (N(2), O(2), and air), temperatures (28, 46, 65 and 80 degrees C), relative humilities (20%, 50%, 65%, 99%) and volumetric UV power inputs (0.87, 1.74, 4.07 and 8.16Wl(-1)) to assess their effects on the HMDS degradation rate. Results indicate that for all conditions, the decomposition rates for the UV (185+254nm) irradiation exceeded those for the UV (254nm)/O(3) process. UV (185+254nm) decompositions of HMDS displayed an apparent first-order kinetics. A process with irradiation of UV (185+254nm) to HMDS in air saturated with water at temperatures of 46-80 degrees C favors the HMDS degradation. With the condition as above and a P/V of around 8Wl(-1), k was approximately 0.20s(-1) and a reaction time of just 12s was required to degrade over 90% of the initial HMDS. The main mechanisms for the HMDS in wet air streams irradiated with UV (185+254nm) were found to be caused by OH free-radical oxidation produced from photolysis of water or O((1)D) produced from photolysis of oxygen. The economic evaluation factors of UV (185+254nm) and UV (254nm)/O(3) processes at different UV power inputs were also estimated.     

Photocatalytic degradation of mixed gaseous carbonyl compounds at low level on adsorptive TiO2/SiO2 photocatalyst using a fluidized bed reactor

An adsorptive silica-supported titania photocatalyst TiO(2)/SiO(2) was prepared by using nanosized titania (anatase) immobilized on silica gel by the sol-gel technique with the titanium tetra isopropoxide as the main raw material and acetic acid as the acid catalyst. Meanwhile the structure and properties of the TiO(2)/SiO(2) photocatalyst were studied by means of many modern analysis techniques such as TEM, XRD, and BET. Gas-solid heterogeneous photocatalytic decomposition of four carbonyl compounds mixture at low concentration levels over ultraviolet irradiated TiO(2)/SiO(2) photocatalyst were carried out with high degradation efficiencies in a coaxial triple-cylinder-type fluidized bed photocatalytic reactor, which provided efficient continuous contact of ultraviolet photons, silica-supported titania photocatalyst, and gaseous reactants. Experimental results showed that the photocatalyst had a high adsorption performance and a good photocatalytic activity for four carbonyl compounds mixture. Some factors influencing the photocatalytic decomposition of the mixed carbonyl compounds, i.e. the gas flowrate, relative humidity, concentration of oxygen, and illumination time, were discussed in detail. It is found that the photocatalytic reaction rate of four carbonyl compounds decreased in this order: propionaldehyde, acetone, acetaldehyde and formaldehyde.     

Photocatalytic degradation of gaseous toluene by using immobilized titania/silica on aluminum sheets

Purpose

The aim of this study was to prepare a highly active immobilized titania/silica photocatalyst and to test its performance in situ toward degradation of toluene as one of the major toxic indoor contaminants.

Methods

In this work, two different titania layers immobilized on Al sheets were synthesized via low temperature sol?Cgel method employing presynthesized highly active titania powders (Degussa P25 and Millennium PC500, mass ratio 1:1): (a) with a silica/titania binder and a protective layer and (b) without the binder. The photocatalysts were characterized by X-ray diffraction, nitrogen sorption measurements, scanning electron microscopy (SEM), infrared spectroscopy, and UV?Cvis diffuse reflectance spectroscopy (DRS). The in situ photocatalytic degradation of gaseous toluene was selected as a probe reaction to test photocatalytic activity and to verify the potential application of these materials for air remediation.

Results

Results show that nontransparent highly photocatalytically active coatings based on the silica/titania binder and homogeneously dispersed TiO₂ powders were obtained on the Al sheets. The crystalline structure of titania was not altered upon addition of the binder, which also prevented inhomogeneous agglomeration of particles on the photocatalyst surface. The photoactivity results indicate that the adsorption properties and photocatalytic activity of immobilized photocatalysts with the silica/titania binder and an underlying protective layer were very effective and additionally, they exhibited considerably improved adhesion and uniformity.

Conclusion

We present a new highly photocatalytically active immobilized catalyst on a convenient metallic support, which has a potential application in an air cleaning device.     

Degradation of the pharmaceutical metronidazole via UV, Fenton and photo-Fenton processes

Degradation rates and removal efficiencies of Metronidazole using UV, UV/H2O2, H2O2/Fe2+, and UV/H2O2/Fe2+ were studied in de-ionized water. The four different oxidation processes were compared for the removal kinetics of the antimicrobial pharmaceutical Metronidazole. It was found that the degradation of Metronidazole by UV and UV/H2O2 exhibited pseudo-first order reaction kinetics. By applying H2O2/Fe2+, and UV/H2O2/Fe2+ the degradation kinetics followed a second order behavior. The quantum yields for direct photolysis, measured at 254 nm and 200-400 nm, were 0.0033 and 0.0080 mol E(-1), respectively. Increasing the concentrations of hydrogen peroxide promoted the oxidation rate by UV/ H2O2. Adding more ferrous ions enhanced the oxidation rate for the H2O2/Fe2+ and UV/H2O2/Fe2+ processes. The major advantages and disadvantages of each process and the complexity of comparing the various advanced oxidation processes on an equal basis are discussed.     

太阳能固定膜光催化去除双酚A的特性与效果

以太阳能固定膜光催化中试装置,研究了光解、初始浓度和平均光强等对双酚A(BPA)光催化去除的影响及BPA的矿化和在自来水中的处理效果.试验结果表明,BPA在日光照射下很难光解,其光催化降解呈表观一级反应,在平均光强介于5.7～23.5 W/m2时,表观反应速率常数和平均光强呈线性关系.太阳能光催化对BPA具有良好的矿化作用,但其降解与以UV254为光源的降解有不同的机理.太阳能光催化对自来水中BPA也具有较好的处理效果.     

A combined plasma photolysis (CPP) method for removal of CS2 from gas streams at atmospheric pressure

A combined plasma photolysis (CPP) reactor that utilizes a dielectric barrier discharge (DBD) plasma and 207 nm UV radiation from discharge-driven KrBr^* excimers was designed and constructed. Gas streams containing CS₂ were treated with stand-alone DBD and CPP at atmospheric pressure. In comparison to DBD, CPP greatly enhanced the removal efficiency at the same applied voltage, waste gas concentration and gas residence time. Thus the applied voltage could be reduced to a certain extent in the plasma processing of industrial wastes. Influences of the KrBr^* radiation, inlet CS₂ concentration and gas residence time on CS₂ removal by CPP were also studied. In addition, the likely reaction mechanisms for the removal of CS₂ by CPP are suggested based on the byproducts analysis. The enhanced removal efficiency and reaction mechanisms implied that the CPP process would probably be suitable for the removal of a large number of gaseous pollutants.     

Removal and Destruction of Organic Contaminants in Water Using Adsorption,Steam Regeneration,and Photocatalytic Oxidation: A Pilot-Scale Study

ABSTRACT

The overall objective of this pilot-scale study is to investigate the technical feasibility of the removal and destruction of organic contaminants in water using adsorption and photocatalytic oxidation. The process consists of two consecutive operational steps: (1) removal of organic contaminants using fixed-bed adsorption; and (2) regeneration of spent adsorbent using photocatalysis or steam, followed by decontamination of steam condensate using photocatalysis. The pilot-scale study was conducted to evaluate these options at a water treatment plant in Wausau (Wisconsin) for treatment of groundwater contaminated with tetrachloroethene (PCE), trichloroethene (TCE), cis-dichloroethene (cis-DCE), toluene, ethylbenzene (EB), and xylenes. The adsorbents used were F-400 GAC and Ambersorb 563.

In the first treatment strategy, the adsorbents were impregnated with photocatalyst and used for the removal of aqueous organics. The spent adsorbents were then exposed to ultraviolet light to achieve photocatalytic regeneration. Regeneration of adsorbents using photocatalysis was observed to be not effective, probably because the impregnated photocatalyst was fouled by background organic matter present in the groundwater matrix.

In the second treatment strategy, the spent adsorbents were regenerated using steam, followed by cleanup of steam condensate using photocatalysis. Four cycles of adsorption and three cycles of steam regeneration were performed. Ambersorb 563 adsorbent was successfully regenerated using saturated steam at 160 °C within 20 hours. The steam condensate was treated using fixed-bed photo-catalysis using 1% Pt-TiO₂ photocatalyst supported on silica gel. After 35 minutes of empty bed contact time, more than 95% removal of TCE, cis-DCE, toluene, EB, and xylenes was achieved, and more than 75% removal of PCE was observed.

In the case of activated carbon adsorbent, steam regeneration was not effective, and a significant loss in adsorbent capacity was observed.     

Kinetics of simazine advanced oxidation in water

Abstract

Comparison of the effects and kinetics of UV photolysis and four advanced oxidation systems (ozone, ozone/hydrogen peroxide, ozone/UV radiation and UV radiation/hydrogen peroxide) for the removal of simazine from water has been investigated. At the conditions applied, the order of reactivity was ozone < ozone/hydrogen peroxide < UV radiation < ozone/UV radiation and UV radiation/hydrogen peroxide. Rate constants of the reactions between ozone and simazine and hydroxyl radical and simazine were found to be 8.7 M^‐1s^‐1 and 2.1x10⁹ M^‐1s^‐1, respectively. Also, a quantum yield of 0.06 mol.photon^‐1 was found for simazine at 254 nm UV radiation. The high value of the quantum yield corroborated the importance of the direct photolysis process. Percentage contributions of direct reaction with ozone, reaction with hydroxyl radicals and direct photolysis were also quantified.     

CdS-TiO2/MWCNTs结构表征及其光催化性能

采用溶胶-凝胶法,制备了多壁碳纳米管（MWCNTs）负载的双组分复合半导体光催化剂CdS-TiO2/MWCNTs。通过透射电镜（TEM）、比表面分析（BET）、X射线衍射（XRD）和紫外-可见吸收光谱（UV-vis）等分析方法对光催化剂进行了结构表征,并考察了CdS-TiO2/MWCNTs对甲苯降解的光催化性能。结果表明：纳米活性粒子CdS-TiO2均匀负载于MWCNTs上,比表面积、光吸收阈值和强度增大,活性粒子间以及活性粒子与载体之间具有协同作用,有利于光催化性能的提高,CdS-TiO2/MWCNTs在主波长为254 nm紫外光照射下对甲苯的降解效果较好,去除率可达55.3%。     

O3／GAC-常规处理珠江水系不同原水

以东江、西江和北江3种原水为研究对象,采用臭氧预处理-常规处理-臭氧活性炭系列处理,研究原水中有机物的去除及臭氧化副产物的产生和转化。结果表明,东江、西江和北江水中CODMn、UV254、甲醛和溴酸盐沿各处理单元过程变化规律基本一致;CODMn总去除率分别为60％、51％和39％,uV。总去除率分别为74％、96％和97％,最终出水甲醛浓度分别为0．004mg／L、0mg／L和0mg／L,B-O3-分别为3．1μg／L、8．7μg/L和35．5μg／L;CODMn的去除主要在预臭氧和活性炭过滤2个处理单元,预臭氧对UV254总去除率贡献最大,甲醛和溴酸盐浓度在主臭氧处理单元达到其峰值（西江甲醛除外）;氨氮和有机物浓度较低、pH值较高的北江原水,出水溴酸盐浓度最高。