Removal of gaseous elemental mercury by dielectric barrier discharge

The removal of elemental mercury (Hg(0)) with the reactive species produced from dielectric barrier discharge (DBD) was studied. The effects of the operating parameters, such as the applied voltage, residence time, initial concentration and co-existence of other pollutants, were investigated. The removal of Hg(0) was significantly promoted by an increase in the applied voltage of the DBD reactor system. The presence of NO gas decreased the Hg(0) removal efficiency within the range of input powers tested compared to the case of Hg(0)-only due to the competition for ozone between Hg(0) and NO gas in the DBD reactor.     

Removal of carbon disulfide via coupled reactions on a bi-functional catalyst: experimental and modeling results

A mathematical model describing the rate of carbon disulfide (CS₂) removal due to coupled reactions has been developed. Kinetic studies were carried out in a fixed bed reactor under atmospheric pressure and a range of temperatures (85–125 °C). The effects of flow rate, CS₂ inlet concentration, temperature and relative humidity were analyzed. A kinetic model based on axial dispersion, external and internal mass-transfer resistances, as well as effects of S deposition on the inner-face of the catalyst was in agreement with the CS₂ experimental breakthrough curves. The mathematical model can be used for process design and scale up of similar systems.     

Biological elimination of H2S and NH3 from wastegases by biofilter packed with immobilized heterotrophic bacteria

Biotreatment of various ratios of H₂S and NH₃ gas mixtures was studied using the biofilters, packed with co-immobilized cells (Arthrobacter oxydans CH8 for NH₃ and Pseudomonas putida CH11 for H₂S). Extensive tests to determine removal characteristics, removal efficiency, removal kinetics, and pressure drops of the biofilters were performed. To estimate the largest allowable inlet concentration, a prediction model was also employed. Greater than 95% and 90% removal efficiencies were observed for NH₃ and H₂S, respectively, irrespective of the ratios of H₂S and NH₃ gas mixtures. The results showed that H₂S removal of the biofilter was significantly affected by high inlet concentrations of H₂S and NH₃. As high H₂S concentration was an inhibitory substrate for the growth of heterotrophic sulfur-oxidizing bacteria, the activity of H₂S oxidation was thus inhibited. In the case of high NH₃ concentration, the poor H₂S removal efficiency might be attributed to the acidification of the biofilter. The phenomenon was caused by acidic metabolite accumulation of NH₃. Through kinetic analysis, the presence of NH₃ did not hinder the NH₃ removal, but a high H₂S concentration would result in low removal efficiency. Conversely, H₂S of adequate concentrations would favor the removal of incoming NH₃. The results also indicated that maximum inlet concentrations (model-estimated) agreed well with the experimental values for space velocities of 50–150 h⁻¹. Hence, the results would be used as the guideline for the design and operation of biofilters.     

Pulsed discharge plasma induced Fenton-like reactions for the enhancement of the degradation of 4-chlorophenol in water

To sufficiently utilize chemically active species and enhance the degradation rate and removal efficiency of toxic and biorefractory organic pollutant para-chlorophenol (para-CP), the introductions of iron metal ions (Fe²⁺/Fe³⁺) into either pulsed discharge plasma (PDP) process or the PDP process with TiO₂ photo-catalyst were tentatively performed. The experimental results showed that under the same experimental condition, the degradation rate and removal efficiency of para-CP were greatly enhanced by the introduction of iron ions (Fe²⁺/Fe³⁺) into the PDP process. Moreover, when iron ions and TiO₂ were added together in the PDP process, the degradation rate and removal energy of para-CP further improved. The possible mechanism was discussed that the obvious promoting effects were attributed to ferrous ions via plasma induced Fenton-like reactions by UV light irradiation excited and hydrogen peroxide formed in pulsed electrical discharge, resulting in a larger amount of hydroxyl radicals produced from the residual hydrogen peroxide. In addition, the regeneration of ferric ions to ferrous ions facilitates the progress of plasma induced Fenton-like reactions by photo-catalytic reduction of UV light, photo-catalytic reduction on TiO₂ surface and electron transfer of quinone intermediates, i.e. 1,4-hydroquinone and 1,4-benzoquinone.     

脉冲电晕低温等离子体提高一氧化氮氧化效率的实验研究

提高一氧化氮（NO）的氧化效率对于提高生物法处理该类废气的净化效率具有重要意义。实验研究了低温等离子体在脉冲电晕条件下氧化废气中NO的过程，考察了不同峰值电压、氧气含量、气体停留时间和添加有机物等因素对提高NO氧化效率的影响。结果表明：低温等离子法可有效地提高NO的氧化效率，主要产物为NO₂；室温条件下，当进气NO浓度590 mg/m³、脉冲频率50 Hz时，增大峰值电压、气体停留时间和进气中的氧气含量可提高NO的氧化效率；在最适峰值电压15 kV，气体停留时间5 s时，NO氧化效率为20%；在进气NO中添加甲苯、乙醇后，NO氧化效率可增加至30%以上，甲苯的效果要好于乙醇。     

Abatement of sulfur hexafluoride emissions from the semiconductor manufacturing process by atmospheric-pressure plasmas

Sulfur hexafluoride (SF6) is an important gas for plasma etching processes in the semiconductor industry. SF6 intensely absorbs infrared radiation and, consequently, aggravates global warming. This study investigates SF6 abatement by nonthermal plasma technologies under atmospheric pressure. Two kinds of nonthermal plasma processes--dielectric barrier discharge (DBD) and combined plasma catalysis (CPC)--were employed and evaluated. Experimental results indicated that as much as 91% of SF6 was removed with DBDs at 20 kV of applied voltage and 150 Hz of discharge frequency for the gas stream containing 300 ppm SF6, 12% oxygen (O2), and 40% argon (Ar), with nitrogen (N2) as the carrier gas. Four additives, including Ar, O2, ethylene (C2H4), and H2O(g), are effective in enhancing SF6 abatement in the range of conditions studied. DBD achieves a higher SF6 removal efficiency than does CPC at the same operation condition. But CPC achieves a higher electrical energy utilization compared with DBD. However, poisoning of catalysts by sulfur (S)-containing species needs further investigation. SF6 is mainly converted to SOF2, SO2F4, sulfur dioxide (SO2), oxygen difluoride (OF2), and fluoride (F2). They do not cause global warming and can be captured by either wet scrubbing or adsorption. This study indicates that DBD and CPC are feasible control technologies for reducing SF6 emissions.     

介质阻挡放电氧化降解木质素磺酸钠的动力学研究

为了有效地处理难生物降解的造纸废水，采用气相介质阻挡放电产生氧化性物质，对木质素磺酸钠进行了氧化降解研究。在不同操作条件下，对其降解动力学及矿化程度进行了研究。结果表明，介质阻挡放电能有效地降解木质素磺酸钠，其氧化降解反应遵循准一级动力学反应。当峰值电压为20 kV，被水蒸气饱和的空气为气源，流量为7 L/min时，氧化处理60 min后，木质素磺酸钠降解率达到70％。其速率常数K随峰值电压、气源、气体流量和木质素磺酸钠的初始浓度的变化而不同。气体流量越大，木质素磺酸钠的初始浓度越低，速率常数K越大，降解效果越好。随着处理时间的增加，氧化性物质能将部分木质素磺酸钠矿化使溶液TOC降低，当被水蒸气饱和的空气作为气源时，氧化处理120min，21.38%的TOC被去除。     

介质阻挡放电净化硫化氢气体的实验研究

采用介质阻挡放电等离子体技术净化恶臭气体硫化氢。考察了电压、频率、硫化氢初始浓度以及停留时间对硫化氢净化效果的影响。结果表明,介质阻挡放电可以有效消除硫化氢污染,硫化氢净化率随电压、频率以及停留时间的增加而升高,随硫化氢初始浓度增加而下降。当电压≥19kV,频率为300Hz,停留时间为1.56s,硫化氢初始质量浓度为30.1mg/m3时,硫化氢净化率接近100%。     

Direct measurement of denitrification activity in a Gulf coast freshwater marsh receiving diverted Mississippi River water

Wetland loss along the Louisiana Gulf coast and excessive nitrate loading into the Gulf of Mexico are interrelated environmental problems. Nitrate removal by soil denitrification activity was studied in a ponded freshwater marsh receiving diverted Mississippi River water for the purpose of reversing or slowing wetland loss. Labeled ¹⁵N-nitrate was applied at 3.8 g N m⁻² into four replicate study plots after removing above ground vegetation. Nitrogen gas (N₂) and nitrous oxide (N₂O) emissions from the plots were determined by isotope ratio mass spectrometry (IRMS). Nitrous oxide emissions were also compared with the results determined by gas chromatograph (GC). Results showed that it took 2 weeks to remove the added nitrate with N₂O emission occurring over a period of 4 d. The apparent denitrification dynamics were assumed to follow the Michaelis–Menten equation. The maximum denitrification rate and K_m value were determined as 12.6 mg N m ⁻² h⁻¹, and 6.5 mg N l⁻¹, respectively. Therefore the maximum capacity for nitrate removal by the marsh soil would be equivalent to 110 g N m⁻² yr⁻¹, with more than 30% of nitrogen gas evolved as N₂O. For typical nitrate concentrations in Mississippi River water of about 1 mg N l⁻¹, nitrate would be removed at a rate of 14.7 g N m⁻² yr⁻¹ with N₂O emission about 1.5%. A denitrification dynamic model showed that the efficiency of nitrate removal would largely depend on the water discharge rate into the ponded wetland. Higher discharge rate will result in less retention time for the water in the marsh where nitrate is denitrified.     

Arsenic removal from water employing heterogeneous photocatalysis with TiO2 immobilized in PET bottles

Arsenic oxidation (As(III) to As(V)) and As(V) removal from water were assessed by using TiO₂ immobilized in PET (polyethylene terephthalate) bottles in the presence of natural sunlight and iron salts. The effect of many parameters was sequentially studied: TiO₂ concentration of the coating solution, Fe(II) concentration, pH, solar irradiation time; dissolved organic carbon concentration. The final conditions (TiO₂ concentration of the coating solution: 10%; Fe(II): 7.0 mg l⁻¹; solar exposure time: 120 min) were applied to natural water samples spiked with 500 μg l⁻¹ As(III) in order to verify the influence of natural water matrix. After treatment, As(III) and total As concentrations were lower than the limit of quantitation (2 μg l⁻¹) of the voltammetric method used, showing a removal over 99%, and giving evidence that As(III) was effectively oxidized to As(V). The results obtained demonstrated that TiO₂ can be easily immobilized on a PET surface in order to perform As(III) oxidation in water and that this TiO₂ immobilization, combined with coprecipitation of arsenic on Fe(III) hydroxides(oxides) could be an efficient way for inorganic arsenic removal from groundwaters.     

Determination of dithiocarbamate fungicide propineb and its main metabolite propylenethiourea in airborne samples

A simple, rapid and sensitive GC–MS method for the determination of dithiocarbamate fungicide propineb [polymeric zinc propylenebis (dithiocarbamate)] and an improved HPLC procedure for the simultaneous determination of its main metabolite, propylenethiourea, and ethylenethiourea, the main metabolite of all ethylenedithiocarbamates, in airborne samples are described. The method for the analysis of propineb involves the evolution of carbon disulfide (CS₂), under acidic conditions in the presence of stannous chloride, extraction of the generated CS₂ into a layer of isooctane which is then analyzed for CS₂ content by GC–MS in SIM mode. Under the optimum conditions, the retention time of CS₂ was 1.89 min and the total time of chromatographic analysis was 5 min. Recoveries from spiking glass microfibre filters (GF/A) and silica gel filters were 86 ± 7 (n = 9) and 89 ± 4 (n = 9), respectively. The limit of detection is 0.7 ng per filter, which is equivalent to about 0.8–1.0 ng m⁻³ in air. In parallel, an HPLC method with ultraviolet detection is presented for the simultaneous analysis of the metabolites. Separation of the two metabolites was attained in less than 5 min. Recoveries from spiking GF/A and silica gel filters for ethylenethiourea were 100 ± 1 (n = 3) and 98 ± 2 (n = 3), respectively, while for propylenethiourea were 102 ± 1 (n = 3) and 98 ± 1 (n = 3), respectively. The detection limits are about 36–43 and 40–49 ng m⁻³ in air for ethylenethiourea and propylenethiourea, respectively. All the analytes spiked in the filters are proven to be stable for more than one month, at −4 °C.     

介质阻挡放电对湖泊水华蓝藻的去除

采用介质阻挡放电等离子体技术去除太湖水华蓝藻,考察了放电输出功率、空气流速、添加剂(异丙醇、腐植酸)等对蓝藻去除的影响。结果表明,介质阻挡放电能去除太湖水华蓝藻,放电功率100 W,空气流速1.0 L/min,放电18min,在光照强度2 000 lx和25℃下培养4 d,初始叶绿素a浓度为9.58 mg/L藻液中蓝藻去除率达87.8%。增加放电输出功率和空气流速能提高蓝藻的去除效率;腐植酸促进了介质阻挡放电对蓝藻的去除;而异丙醇添加剂抑制了介质阻挡放电的作用。放电处理后,蓝藻细胞内类胡萝卜素含量、SOD活性、MDA含量发生明显变化,介质阻挡放电破坏了蓝藻细胞内含物。     

Radiolysis of aqueous 4-nitrophenol solution with Al2O3 or TiO2 nanoparticles

Aqueous 4-nitrophenol solutions containing TiO₂ or Al₂O₃ nanoparticles were irradiated with electron beam. 4-nitrophenol was decomposed by the ionizing radiation process in the absence of the nanoparticles. The addition of TiO₂ or Al₂O₃ (2 g l⁻¹) before irradiation improved the removal of 4-nitrophenol, total organic carbon (TOC) but also nitrogen (TN). To identify the origin of the loss (catalysis or simply adsorption), TiO₂ or Al₂O₃ nanoparticles were added after irradiation. Experiments show that the effect of the presence of TiO₂ or Al₂O₃ during irradiation is just due to adsorption.     

Compound-specific chlorine isotope analysis of polychlorinated biphenyls isolated from Aroclor and Clophen technical mixtures

The combined electrochemical oxidation-solar-light/immobilized TiO₂ film process was conducted to degrade an azo dye, Reactive Black 5 (RB5). The toxicity was also monitored by the Vibrio fischeri light inhibition test. The electrochemical oxidation rapidly decolorized RB5 (55, 110 μM) with a supporting electrolyte of 2 g l⁻¹ NaCl at current density 277 A m⁻² and pH 4. However, TOC mineralization and A₃₁₀ removal were low. Additionally, the treated solution showed high biotoxicity. RB5 at 110 μM significantly retarded the de-colorization efficiency by using the solar-light/immobilized TiO₂ film process. The combined electrochemical oxidation-solar-light/immobilized TiO₂ process effectively increased the removal of color, A₃₁₀, and TOC. The toxicity was also significantly reduced after 3 h of solar irradiation. The results indicated that the low-cost combined process is a potential technique for rapid treatment of RB5.     

Abatement of Sulfur Hexafluoride Emissions from the Semiconductor Manufacturing Process by Atmospheric-Pressure Plasmas

Abstract

Sulfur hexafluoride (SF₆) is an important gas for plasma etching processes in the semiconductor industry. SF₆ intensely absorbs infrared radiation and, consequently, aggravates global warming. This study investigates SF₆ abatement by nonthermal plasma technologies under atmospheric pressure. Two kinds of nonthermal plasma processes—dielectric barrier discharge (DBD) and combined plasma catalysis (CPC)—were employed and evaluated. Experimental results indicated that as much as 91% of SF₆ was removed with DBDs at 20 kV of applied voltage and 150 Hz of discharge frequency for the gas stream containing 300 ppm SF₆, 12% oxygen (O₂), and 40% argon (Ar), with nitrogen (N₂) as the carrier gas. Four additives, including Ar, O₂, ethylene (C₂H₄), and H₂O_(g), are effective in enhancing SF₆ abatement in the range of conditions studied. DBD achieves a higher SF₆ removal efficiency than does CPC at the same operation condition. But CPC achieves a higher electrical energy utilization compared with DBD. However, poisoning of catalysts by sulfur (S)-containing species needs further investigation. SF₆ is mainly converted to SOF₂,SO₂F₄, sulfur dioxide (SO₂), oxygen difluoride (OF₂), and fluoride (F₂). They do not cause global warming and can be captured by either wet scrubbing or adsorption. This study indicates that DBD and CPC are feasible control technologies for reducing SF₆ emissions.     

吸附增效低温等离子体法去除甲苯废气的研究

采用150Hz中频高压交流电源作为低温等离子体发生源,选用典型的微孔γ-Al2O3球形颗粒吸附剂(以下简称γ-Al2O3)作为等离子体反应器填充材料,协同低温等离子体法催化降解甲苯废气。考察了在不同条件下,γ-Al2O3的甲苯吸脱附效果和吸附增效低温等离子体法的甲苯去除效果。结果表明,甲苯降解反应主要发生在γ-Al2O3的表面,甲苯的去除率在一定的浓度范围内与γ-Al2O3表面吸附的甲苯量成正比关系;填充γ-Al2O3有利于提高甲苯去除率及等离子体反应器能量利用率;γ-Al2O3对臭氧的降解表现出一定的促进作用。     

The use of physiological characteristics for comparison of organic compounds phytotoxicity

The influence of intact (FLT) and photomodified (phFLT) fluoranthene (0.05, 0.5 and 5 μmol l⁻¹) and herbicide Basagran (5, 20, 35 and 50 nmol l⁻¹) on the germination, growth of seedlings and photosynthetic processes in pea plants (Pisum sativum L., cv. Garde) was investigated. The germination was significantly inhibited already by the lowest concentration (0.05 μmol l⁻¹) of FLT and phFLT, while Basagran caused inhibition only in higher concentrations (35 and 50 nmol l⁻¹). The growth of roots was significantly inhibited by higher concentration 5 μmol l⁻¹ of both FLT and phFLT and the shoot of seedlings was significantly influenced only by photomodified form. The length of root and shoot was inhibited already by concentration 5 nmol l⁻¹ of Basagran. Organic compounds applied on chloroplasts suspension influenced primary photochemical processes of photosynthesis. In chlorophyll fluorescence parameters, the significant increase of F₀ values and the decrease of F_V/F_M and Φ_II values by application of FLT (0.5 and 5 μmol l⁻¹) and phFLT (0.05, 0.5 and 5 μmol l⁻¹) was recorded. The maximum capacity of PSII (F_V/F_M) was influenced by the highest (50 nmol l⁻¹) and the effective quantum yield of PSII (Φ_II) already by the lowest (5 nmol l⁻¹) concentration of Basagran. Hill reaction activity decreased and was significantly inhibited by higher concentration (0.5 and 5 μmol l⁻¹) of FLT and phFLT and already by the lowest concentration (5 nmol l⁻¹) of Basagran.     

Nitrogen trace gas emissions from a riparian ecosystem in southern Appalachia

In this paper, we present two years of seasonal nitric oxide (NO), ammonia (NH₃), and nitrous oxide (N₂O) trace gas fluxes measured in a recovering riparian zone with cattle excluded and adjacent riparian zone grazed by cattle. In the recovering riparian zone, average NO, NH₃, and N₂O fluxes were 5.8, 2.0, and 76.7 ng N m⁻² s⁻¹ (1.83, 0.63, and 24.19 kg N ha⁻¹ y⁻¹), respectively. Fluxes in the grazed riparian zone were larger, especially for NO and NH₃, measuring 9.1, 4.3, and 77.6 ng N m⁻² s⁻¹ (2.87, 1.35, and 24.50 kg N ha⁻¹ y⁻¹) for NO, NH₃, and N₂O, respectively. On average, N₂O accounted for greater than 85% of total trace gas flux in both the recovering and grazed riparian zones, though N₂O fluxes were highly variable temporally. In the recovering riparian zone, variability in seasonal average fluxes was explained by variability in soil nitrogen (N) concentrations. Nitric oxide flux was positively correlated with soil ammonium (NH₄⁺) concentration, while N₂O flux was positively correlated with soil nitrate (NO₃⁻) concentration. Ammonia flux was positively correlated with the ratio of NH₄⁺ to NO₃⁻. In the grazed riparian zone, average NH₃ and N₂O fluxes were not correlated with soil temperature, N concentrations, or moisture. This was likely due to high variability in soil microsite conditions related to cattle effects such as compaction and N input. Nitric oxide flux in the grazed riparian zone was positively correlated with soil temperature and NO₃⁻ concentration. Restoration appeared to significantly affect NO flux, which increased ≈600% during the first year following restoration and decreased during the second year to levels encountered at the onset of restoration. By comparing the ratio of total trace gas flux to soil N concentration, we show that the restored riparian zone is likely more efficient than the grazed riparian zone at diverting upper-soil N from the receiving stream to the atmosphere. This is likely due to the recovery of microbiological communities following changes in soil physical characteristics.     

Microwave-induced combustion of volatile organic compounds in an industrial flue gas over the magnetite fixed-bed

A modified domestic microwave oven was applied to heat a magnetite (Fe₃O₄) fixed-bed for continuous decomposition of volatile organic compounds (VOCs), such as acetone, n-hexane, and dichloromethane (DCM), in a simulated flue gas which contains VOCs equivalent to 2000 ppmv as DCM. Experimental results revealed that effect of the addition of water to the inlet stream on decomposition of DCM in the overall experiment was insignificant. Bulk temperature of the Fe₃O₄ fixed-bed was also found to reach 600 °C from an initial room temperature by 6.5 min under microwave radiation, even though the inlet gas was at a high gas hourly space velocity of 5240 h⁻¹ and a high relative humidity of 75%. Moreover, the VOCs in the inlet stream could be decomposed completely over the Fe₃O₄ fixed-bed by microwave heating at a power level of 645 W at heating time of 10 min. The conversion of VOCs is stable when the Fe₃O₄ fixed-bed has been heated longer than 10 min with microwave radiation. The microwave-induced heating upon Fe₃O₄ fixed-bed processing appears to be not only an energy efficient technique for air pollutions treatment but also a promising technology for variety of VOCs in a flue gas from industrial factory being decomposed simultaneously and completely.